D-Link DIR-615 :: Cannot Get Printer To Show Up On Home Network
Mar 3, 2011
I recently purchased a HP PHOTOSMART D110 wireless/eprint all in one. I have the dir-615 router and cannot get the printer to show up on my home network.Printer works fine hard wired to pc but wireless not at all. The ip address of the printer is 169.254.147.xx while everything on my network is 192.168.0.xx. Printer says connected for a few seconds then disconnected....I have tried to configure it on a vista and a win 7 machine.Everything else shows up fine on my network, as a matter of fact a friend brought his laptop over and it connected great..
View 14 Replies
ADVERTISEMENT
Jan 15, 2011
I have an HP3505 working fine on my home network, accessible from several machines on Vista and Windows 7. But it won't show up on the network map (on any of the machines), even though my other devices (such as network drives, etc.) do. Maybe it doesn't matter, since it works, but how do I get it to show up?Brad
View 3 Replies
View Related
Feb 23, 2012
My new DCS-932L home network camera does not show up in MY DEVICES acct!! Only my FIRST camera show up, therefore I cannot access my SECOND camera remotely on my phone or other computer! When I ran the cd installation for the second camera, it could not access my network.....However I was able to install camera manually....it is working fine, I am getting my motion detection e-mails notification, I am able to access camera thru my laptop....What do i have to do in order to my second camera to show in MY DEVICES Acct? so I can access camera remotely?
View 3 Replies
View Related
Jul 7, 2011
I wanna setup a small office network ? how do I setup and can I use a printer on this LAN ??
View 3 Replies
View Related
Jan 4, 2012
I bought a new laptop with Windows 7. Desktop is running Vista. Printer is set to share and connected to Vista machine. Printer and file sharing is enabled on both machines. Running Windows firewall on both machines. Disabled Comodo firewall on Vista machine. Both computers have the same workgroup. Both computers have the same user name and password. Password protected sharing is turned off both machinesVista can access the W7 machine, last night W7 could see but not access Vista, but it doesn't even see it. When I troubleshoot I get a message "file and print sharing resource (Vista PC name) is online but isn't responding to connection attempts".
View 1 Replies
View Related
Jul 1, 2012
I'm running into an issue with allowing all the PCs to use the one printer connected to devpc. I have a westell 7500 from CenturyLink and a Belkin Wireless G router. This is the layout:
View 6 Replies
View Related
Apr 5, 2011
I just installed Win 7 pro 64 bit on a new computer / hard drive. I can connect to my router which is hardwired to a computer running Win XP Pro 32 bit, but I can't figure out how to connect to my printer which is on that same network. I can access the internet, just not the printer - which is connected via Ethernet to the router.Is is possible that because Win7 is 64bit and the other computers on the network are 32 bit running XPpro - that it won't work? I have another XP pro computer that is connected via wireless that accesses the printer just fine.I have a netgear USB adapter on both the WinXP computer and also the Win7.Win7 is foreign to me. I can't find anywhere where I would 'join' the mshome network. It asks me about them joining ME.
View 10 Replies
View Related
Feb 22, 2012
My wife has a work laptop that she uses to connect to the internet and she can only do this through her work VPN.
I have a windows 7 desktop and can connect fine to a wireless HP 6500A Plus wireless printer on the same home network that my computer is connected to. So my computer prints wirelessly just fine.
She needs to print onto this same printer. We just spent 2 hours on the phone with a tech support guy from her work and we can't get it.
I'm computer savvy but not familiar with VPN's at all. How do we get her laptop, connected through VPN, to connect to the printer on my home wireless network.
she accesses the VPN through my home network.
View 7 Replies
View Related
May 6, 2011
I've got a small wireless home network that currently has 2 computers - my desktop is running XP Pro, and a laptop that my wife uses running XP Home. I've recently bought a new laptop that is running Windows 7, and although it picks up the wireless feature of the network (it has wireless internet access), I can't seem to figure out how to get this new Windows 7 laptop to see the other PCs or the printer connected to my desktop. I've tried a couple of the "how-tos" online, but I must be doing something wrong. getting my Windows 7 box to see the other PCs and printer on my network
View 3 Replies
View Related
Dec 30, 2011
I have decided to set up a simple network at my home. I have got 2 PC's (one ground floor, one up staris), printer, TV and router.Now, my router has got only 4 sockets for RJ45 (no usb connection available). My target is to have one storage hard drive of 2TB for sharing pictures, files and automatic backup from PC's. Make of my router is D-link DIR-615. I want to have PC's connected by RJ45 for quick file transfer and TV as well to load movies from external/network hard drive so 3 of 4 ports are already used.I want to have my printer online in network all the time, so any PC can print at any time without connecting USB cable. Also I do not want to plug my printer into PC downstaris and share it in the network because if PC will be switched off, PC upstaris won't be able to print. So I want all my devices have connected to the router. Printer does not support ethernet interface as well (only usb connection).I've got a choice to buy an External Hard Drive (USB) or Network Hard Drive. I have choosen these two:
[URL]
As I said, I got 2 devices to connect to my network, and there is also one port available. I know, we got many different hubs etc, but what about printer? It supports only USB 2.0.I have also found very basic NAS on ebay:
[URL]
I thought I could by external hard drive because it is cheaper than network, and connect it together with my printer to this NAS and then NAS to router. Will I loose file transfer speed?
View 1 Replies
View Related
Oct 29, 2011
I'm having issues connecting a HP 9000dn printer to my home network. I have windows 7 x64 with a Belkin wireless router. I have the printer (via a jetdriect 615n driver) connected to my router and the computer will not see the printer. I'm a newbie to networking
View 3 Replies
View Related
Jun 2, 2011
I've got a modem which feeds a wireless router; plugged into the router via ethernet cables are my personal computer in my room and an office computer. Connected wirelessly is my kitchen PC. My printer (Canon MX330) is not wireless/bluetooth and is connected via USB to my office computer.
Office / Kitchen Computers: Windows XP My Personal Computer: Windows 7
I'm trying to set up a network/file sharing system, and more importantly, I'm trying to be able to print on a computer other than my office computer.
View 1 Replies
View Related
Feb 19, 2011
Is it possible toconnect a wired printer to the router and have it become a part of the network?
View 6 Replies
View Related
Sep 18, 2012
I'm newbie in Networking. I want to establish a small WLAN network where all the laptops (6 laptops) can use WiFi Internet and also can print via a network printer.I have these hardwares:1: DSL Modem2: A Belkin F5D8233-4 300 Mbps router3: A Network printer (with RJ45 ethernet port, Not wireless printer)4: LAN Cable (if needed)5: Finally 6 Client Laptops
View 4 Replies
View Related
Mar 1, 2011
I am currently having a problem connecting a hardlined (ethernet connected) PC to a wireless printer. I want to know first of all if this is even possible. If so, how can I make this work? I know just enough about networking to be dangerous, but not enough to see what I am doing wrong. My network structure is as follows:
a 2Wire wireless modem/router provided by my ISP. a win xp laptop connected wirelessly a vista laptop connected wirelessly a win xp pc connected via the 2Wire ethernet port a Lexmark 4530 printer with wireless adapter connected wirelessly wireless config is WPA-personal (TKIP)
The laptops are able to print to the printer, but that is only because I used the CD for the printer to setup the wireless printing. When I look at the network neighborhood on both laptops, the printer does not appear. This leads me to believe that the printer is not connected to the network, the laptops have just created a printer connection (the port designation leads me to believe this as it just shows Lexmark 3500_4500 and not an actual address). The hardlined PC can connect to the internet, but is not visible to either of the PC's. When I try to type in the IP address listed on the printers config page, it doesn't see it. I can ping it, but can't connect. I think my problem is in the connection of the wireless printer. I can see it in the connection screen of the 2Wire status page, but I have a funny feeling it isn't configured properly. There appears to be no way to configure the printer outside of using their "wireless connection utility wizard" on the CD.
There is one other twist to this, I have a Dlink DGL4300 wireless gaming router that I use for my XBOX and to give me additional hardline ports for other things. I don't have it connected right now (my box is out of commission waiting on parts), but I did have it connected behind the 2Wire before without any problems. I would like for it to remain this way once I have the printing problem resolved. I am using DHCP right now with auto assigned IPs, but I can reconfigure the network to whatever will allow me to get this to work properly.
View 3 Replies
View Related
Aug 28, 2011
I have a home network with an older desktop, two laptops, couple of PDA and now a cellphone. I'm using using a WRT 110 router I bought new a couple of years ago. It run flawlessly even when I switch from DSL to Comcast Internet.My printer (HP All-in-one) is currently attached to the rear of my desktop and if I want to print anything I have to fire up the desktop. Can I plug the printer in the WRT 110? Be able to print form my laptops?
View 4 Replies
View Related
Sep 10, 2011
I have a D-Link DGL-4500 router and my landlord recently ungraded our internet connection. However, now I get this error message when I try to hook it up to the ethernet hub,"The addressing of the Internet side learnt thru DHCP conflicts with the addressing selected for the LAN side. Internet communications will be disabled until you have changed the LAN side addressing to resolve the problem."
View 3 Replies
View Related
Dec 11, 2012
i use cisco vpn client software to connect my laptop to my company's network when i at home. using dsl modem.
i wonder if it is technically possible to connect my local printer to dsl router and in such a way establish connection between my laptop and printer?
View 5 Replies
View Related
May 17, 2011
This is the configuration I am running:Internet > Cable Modem > Netgear WNDR3700 Router ~~ DAP-1522 > Wired Windows 7 PC + Linux PC + Printer.The Windows 7 and Linus PC's do communicate well to the internet as do any laptops accessing the router wirelessly and any devices wired to the router. That is the good news.
The bad news is that any devices located after the DAP-1522, including the DAP-1522 do not show up on the network map of either the router or any of the wireless laptops. Neither does the Win 7 PC connected through the DAP-1522 show any networked devices, whether through the DAP-1522 or not, even though network discovery is turned on.
Right now the DAP-1522 is set up to function as a bridge and is in "Static IP" mode. I tried changing it to DHCP, but the DAP-1522 will not allow saving that setting, even though it will allow changing it. It just reverts back to "Static IP". The firmware version is 1.31, and the firmware update went well after a workable logon to the admin page was discovered. Also the one-button (WPS) set-up to the router worked as far as allowing an internet connection.
What needs to change to allow all the devices to show up on the network maps and maintain internet access? Ultimately, I would like to stabilize the IP's of the major components of the network to make troubleshooting easier. But to do that the devices need to show up on the network maps, particularly of the router, so they can be added to the IP reservation table by selection.
View 2 Replies
View Related
Feb 5, 2012
I recently bought and installed a DIR-615 for my home network, and downloaded the Yahoo Widget.
Widget recognizes and display all the config information (LAN, WAN, WiFi) fine, but it does no display any of the speeds (which was the whole idea).
View 2 Replies
View Related
Feb 25, 2012
I can see what MAC addresses have a wireless session and I've used MAC Filtering to stop some MAC addresses from using the network at certain times, but they are still getting through to the internet. I don't know if they were to clone their MAC address as to whether this would show up with the cloned address in active sessions list. How I can stop some users from getting through at certain times? Any utility I can use on my Mac (Mac OS X 10.6. to show which computers/MAC addresses are on the network?
View 5 Replies
View Related
Sep 29, 2012
My setup: Windows 7 desktop; Vista laptop. Only one user account on each, with no password.I can share files between the two computers, but only by putting the shared files in the Public folders, otherwise access is denied based on username and password.It is inconvenient, but I can live with sharing files through the Public access.However, a printer connected via USB to the desktop cannot be seen from the laptop. This desktop is new. It replaced an XP desktop on which file and printer sharing worked easily with the same network.
View 2 Replies
View Related
Jun 15, 2012
I have a DCS 3420 that is connected via CAT5 to may LAN and 2days ago something happened on the laptop, whenever I open the window in internet explorer on Win XP Pro; the camera just show a black screen.If I use any other computer on my LAN I get a clear picture of the Gate that the camera is focused on...I have checked the laptop drivers and updates but ca not see something wrong.
View 1 Replies
View Related
Oct 12, 2011
I have had my DIR 615 router for about 6 months, and have had no problems. I have a notebook (Sony Vaio) and I also have a Blue-Ray Player and my DirecTV DVR connected by ethernet. Starting a few days ago I was having connectivity issues. At first I could see the network on my Vaio, but the Internet kept coming and going.I did some troubleshooting on the adapter and that seemed to work. Now I am having an issue where every 2 hours or so the wireless drops and the network disappears from the list of available connections on my notebook. I have had my netbook on (connected wireless) and the issues are replicated on that system.
Both of my wired devices do not see any interruption in connectivity. Living in an apartment complex I suspected interference and indeed there are a ton of other networks in range (as per inSSIDer 2.0). As there is no channel that is clearly open, I have set my router to auto channel scan. I also have tried some of the steps outlined in other threads. The thing I am noticing is that when the network connection drops my network (which has a unique name) doesn't even show up on inSSIDer, it just disappears. When working, my network is consistantly in the -25 range on inSIDDer.I should point out also that my notebook is a mere 8 feet from the router, and there are no obstructions.
View 1 Replies
View Related
Feb 16, 2011
I have a Samsung CLP-315W printer wireless that i cant communicate with. I get network printer status not available. I contacted Samsung support and they said to talk to my router manufacture and get the network configuration and enter it manually.
View 9 Replies
View Related
Mar 7, 2013
I have a cabled network printer, Xerox Phaser 6125n, that have always worked properly from my 3 desktop computers and my laptop.A few days ago, my old dlink router went dead, and I replaced it with the TP-Link WDR4300 router. Everything worked as usual afterwards, until I found out I could no longer print on my printer. I can access the printers web interface through the ip adress, change settings and such through the browser, but the printer has offline status in windows and print jobs never leaves the print queue in windows. I tried deleting the printer in windows (tried both windows 7 and 8) to reinstall it.
View 7 Replies
View Related
Dec 31, 2011
I don't see a forum for the DIR-665 so I am posting this here.I have setup my network using the DIR-665. I can print to my network printer (not plugged into router usb it is a Network printer) from WIN XP and Mac Snow Leopard and Lion via a network cable.
When I connect to the router via WIFI it shows the printer is ready. Then I click print and it starts trying to find the printer but then fails saying the printer is not on the network.
View 14 Replies
View Related
Dec 18, 2010
I recently purchased a DIR-655 and everything's working fine -- Internet access, visibility of local shares, etc. -- with the one except accessing to my printer (Brother MFC-7440N) that's hard-wired to a port on the router.After installing the latest PC SharePort Utility on my two Windows 7 desktops, they're both able to connect and use all of the features of the printer (print, scan, etc.). However, I can't say the same for my two Macbook Pro's connected via WiFi (802.11N). I installed the latest Mac SharePort Utility on both, but neither can "see" the printer. Caveat: If I connect the laptops via a LAN cable (ie. hard-wired directly into the router), they're able to see the printer. how to configure the router (or Mac) to allow them to see the printer?
View 9 Replies
View Related
Apr 7, 2011
Camera set up with the Beta Mac wizard connected via ethernet on Airport base. Wireless security WPA2 Personal. Using DHCP. AirPort Utility 5.5.2, OSX 10.6.6.I can see the cam with the myDlink Lite iPhone (4) App when I am in my house with my wireless network. When I am out, away from my network, the App can't connect to the cam, tells me to check my network settings. I did the wps way and added the cam in the airport base utility *Access Control* tab but still doesn't work. Checked in the cam web page settings, can't figure out what the Pre-Shared Key is and where I get it/set it up in the airport utility...
View 1 Replies
View Related
Sep 25, 2011
I want to create a link between two homes about 10/15 miles away from each other. I was thinking about using microwave technology to achieve this. I would like to be able to use this connection for linking two home networks/internet and possibly running iptv and voip over the link. I was hoping to operate in the unlicensed frequency.
View 2 Replies
View Related
Jul 3, 2011
I have 2 internet services with separate ISPs. My local telephone exchange is somewhat dated so the maximum speed per ISP/connection is about 1 Gbps. I have streaming radio services, I do quite a bit of file downloading and there multiple devices currently trying to share a single connection. I haven't been able to utilise the second connection because my NAS and print serving is all configured on the first connection and therefore unavailable to users/services on the second connection.My goal is to utilise the available capacity of both connections but at the same time allowing all network resources (file and printer sharing, NAS drives, etc.) to be available jointly to all network clients.
My first router is a Netgear RangeMax ADSL modem/wireless router (DG834PN). This connects directly to one ISP and has the NAS and printers attached. The second router is a Netgear N600 wireless dual band router (WNDR3400) which attaches to a Linksys ADSL 2 Gateway with 4-port switch (AG241 v2) and then to the second ISP.As an aside, I also have a number of Devolo devices for utilising the electrical circuit for networking purposes. I have a dLAN 200 AVmini adapter connected to the RangeMax router with 2 further dLAN 200 AVmini adapters and a dLAN 200 AV wireless N adapter distributed through my house.
View 2 Replies
View Related
Jul 23, 2011
I have tried to open ports, but if I use the [URL], I just get the closed. I have tried to use the Viritual server function, but can`t se to get it open.
On my old, D-Link I also had something cal port forwarding, this is not here. Here is a link to an emulator of the router: [URL]
View 13 Replies
View Related
Nov 20, 2011
What device would be necessary to link two networks of identical type? What devices would be necessary to link two networks of dissimilar types?I would say a network card and HUB for identical type but I do not know if this is correct?Describe the parameters governing the choice of cable type for a given network. What are the three main types of cables used in computer networks?
View 3 Replies
View Related
