I have an HP3505 working fine on my home network, accessible from several machines on Vista and Windows 7. But it won't show up on the network map (on any of the machines), even though my other devices (such as network drives, etc.) do. Maybe it doesn't matter, since it works, but how do I get it to show up?Brad
View 3 RepliesI recently purchased a HP PHOTOSMART D110 wireless/eprint all in one. I have the dir-615 router and cannot get the printer to show up on my home network.Printer works fine hard wired to pc but wireless not at all. The ip address of the printer is 169.254.147.xx while everything on my network is 192.168.0.xx. Printer says connected for a few seconds then disconnected....I have tried to configure it on a vista and a win 7 machine.Everything else shows up fine on my network, as a matter of fact a friend brought his laptop over and it connected great..
View 14 Replies View RelatedI have a Motorola Affix and am using the app printershare to print from my phone to a network printer at home.. it works great.. but I want to know if there is a way to make the printer accesable from the internet so I can print from pt phone when im not home and connected to the network...accessible
View 2 Replies View RelatedWould it be possible to make a printer accessible from internet? Need to print a lot of batch printing from my cloud application , in that case can we direct this print job to a specific printer over internet ?
View 1 Replies View RelatedI have 2 desktops (running windows 7), a Canon MF8300 printer, and an outgoing ethernet line, all on a Netgear Advanced Cable Modem Gateway CGD24-CPR. I'm only concerned with having the 2 desktops set up with the Canon printer.Both computers have been connected to the printer before and I have the startup disk. But once the new offices were set up and both of the desktops were moved, I can no longer access or find the printer.
I can IPconfig the Desktops for their IPV4 addresses and both desktops recognize eachother on a Homegroup, but I can't find the printer. I printed off the print configuration page from the printer which gave me an IP address (printer is set for auto-obtain), but using an IP search won't bring up the printer.All of the devices are plugged into ethernet ports set up for the three different office they are in and the actual location of the Netgear cable modem/router is over 100 feet away. My primary concern is getting the printer for the desktops, but I also need to add a wireless router into one of those office in the future.
I have configured a vlan interface on a 3750 switch. there is aprox 4Mb active traffic flowing through the interface, but when I do a "show interface vlan (vlanid)" the output show zero bits in and zero bits out. Its a typical L3 config with one IP on the vllan interface acting as the gateway for the VLAN devices. Is this a normal behaviur ? and if so is there any way to get the traffic in/out stats. The end PC/devices are connected to this switch via an L2 TRUNK and I dont have access to the L2 switch on which the actual devices connect. so cant get the real time stats of those interfaces.
View 2 Replies View RelatedHow to understand "show sessions" and "show connection" commands? And what is the difference between the two?
View 2 Replies View RelatedFacing issue with 2960G switch , where its do not display "logging trap informational " in show running and show startup .where its showing all other levels from 0 to 5 and 7 after configuration and save commands. [code] after config getting saved , it do not shows in show runn or in show startup while for all other levels it do show the config lines .I tried the same on 12.55.SE release also but its same results . Is this a limitaion of this platform, is there any doc explaining the same for reference. [code]
View 1 Replies View RelatedI have a cisco 1760 with running VIC-2FXO (working fine). I'm now trying to replace that line with an ISDN line through a VIC2-2BRI.
View 4 Replies View RelatedWe have a network configured this way : 192.168.1.1/24 and we reached it's limit, is there any way to extend it having the same scheme and keeping communications between the machines, I've tried 192.168.2.1 but it simply doesn't work.
View 8 Replies View RelatedI'm running Windows XP, SP3. This is a friends computer that I'm trying to fix. It had a virus which I removed, however it left behind a damaged computer. Now there are no network devices that show up in "Network Connections" or in Device Manager. I tried to reinstall the drivers, but I got this error: "The Realtek Ethernet Controller was not found. If Deep Sleep Mode is enabled Please Plug [sic] the Cable".
View 1 Replies View RelatedI have 2 computers One desktop and one Laptop Both are Vista Home Premium I want to set up a network between them to share files-printer etc Done exactly what it says here [URL]Went to the Desktop pc - Chose turn on network discovery, both are in Workgroup name Picked Private Network and turn on Printer Sharing.and no passwords.Then tried to see a folder I shared. But the laptop could not see it Or the PrinterSo thought maybe I needed to set up sharing on the laptop too? Did I? So set the laptop up exactly the same.
View 14 Replies View RelatedMy desktop is my main computer and is connected to a wireless router. I have added my laptop which i can see and can get into it's files. On the laptop, I cannot get into the desktop files and I cannot share the printer that is connected to the desktop.
View 4 Replies View RelatedI have a router, networking 2 computers. One of them I wish to set to "ad-hoc" I do not want it accessing the internet.
So, a "wired ad-hoc".
The best discriptsion I have is on a Vista or 7 machine you have the Network map I want to disconect the computer from the internet, and leave it connected to the network.
Wireless Network Connection window will not show any of avail local networks
View 8 Replies View RelatedSince downgrading from vista to xp on tower (packard bell bv)have had internet connection issues (no workie!).device manager shows no modem,but modem working fine through laptop wireless set up.odem is through virgin (netgear),have tried to find update for netgear drivers(no chance)but obviously modem is working ok through laptop!have also tried to find update on motherboard (m2 ns-nv, 1.xxbus clock 200mghz bios phoenix tech).
View 1 Replies View RelatedI got the Cat-5e network cable but I cant get it to show up, when I plug it in I cant seem to get it to show up on my computers.
View 4 Replies View RelatedIs it possible to have web browsers load a specific file upon first launch when connected to a certain network (i.e. like public wifi hotspots automatically redirect your browser to their login page when you first connect). Would I be able to create a page that would act as a welcome page to people who have connected to my network (and probably to myself too).I want it to act as a welcome page to my network - to be honest, I don't know why I need it, it just seems fun to find out if I can (I sound so geeky now)
View 1 Replies View RelatedI have two computers, one vista (Laptop) the other XP (Desktop). Now the problem is that i can't see my vista laptop on my XP, but both are connected to the same router (Netgear DG2200). The router also has a hard drive connected as a network drive WHICH i can see on the XP.
Problem is, nothing comes up on the Vista laptop except for the router and itself. Not even the network hard drive. I can view it on my PS3, though.
I noticed my lan is not enabled on my laptop, so how do i enable it? I tried diagnosing but it said to connect the lan cable.
Every once in a while when logging into Windows (7 Ultimate 32 bit) My PC decides it couldn't find a network connection, usually restarting the computer solved the problem, however now I have seemed to permanently be stuck on the "identifying" stage of my LAN connection. My mobo is an Asrock p67 extreme, the network adapter is a realtek pcie family card.Now I know it is not my modem since I can connect on my other PC in the living room, I verified this with a phone call to my ISP, they couldn't see my PC connected to the network but could see the other one.It is not the Ethernet cords, I switched them and even used a new one. I tried rolling back, installing updated and installing factory drivers for my network card, no change.
I tried turning off the PC, disconnected the power cord, discharged it, left everything off/ disconnected for 30 minutes and reattached, powered on, no change.I made sure my DHCP was on and that my PC was set to automatically retrieve IP/DNS.I even bought a new Ethernet card, installed it and I still can't connect, so its not the realtek card.I can't even access my modem using its UP address, 192.168.2.1 (Bell 2wire) but I can on my 2nd PC, it sees all other devices, PS3 /Smartphones but not my PC.
I am running windows 7 HP. We have about 10 devices in one office and 5 devices connected thru a VPN..... When i hooked everything up 4 weeks ago I could see all the devices in the main office and the remote office connected thru the VPN (In the Network Folder that lists everything connected). Now I only see like 4 device and they are all in the main office.
I did some research a couple weeks ago and found a command prompt that "refreshed" all the devices that were connected, but now They are gone again and I cannot remember the command prompt!
I have a small business network computers w/a linux server. One computer was infected with viruses which I removed via kaspersky/norton/malware anti-bytes. I run windows xp professional on this computer.However I run into the following problem:
1) In my network places the documents on the server do not show as a network place-this is despite me being able to access these documents via a folder shortcut
2) After I open the network files/folders from the comp, I am unable to use the find feature because the folder is not listed under the look in drop box. I tried changing workgroups and ran into the same problem.
I can't find my linksys network on the "wireless networks" I've been able to use it many other times but just this past week it hasn't been showing.
View 1 Replies View RelatedMy new DCS-932L home network camera does not show up in MY DEVICES acct!! Only my FIRST camera show up, therefore I cannot access my SECOND camera remotely on my phone or other computer! When I ran the cd installation for the second camera, it could not access my network.....However I was able to install camera manually....it is working fine, I am getting my motion detection e-mails notification, I am able to access camera thru my laptop....What do i have to do in order to my second camera to show in MY DEVICES Acct? so I can access camera remotely?
View 3 Replies View RelatedI have an internet connection coming into my house. The modem is in the basement along with the desktop computer and the wireless router is wired upstairs where coverage is the greatest. Could some tell me how I would make these connections/ hardware needed to have them all on the same network?
View 1 Replies View Relatedhow can i make a 2 km wirless network for dsl internet. my friend lives 2 km far from my home,he has a dsl connection.but there is no facility of dsl availble to my side.how can we make a wireless network?
View 3 Replies View RelatedI would like to make a network for my house where my laptop connects to my home wifi and other computers can connect to my laptop and get internet, almost like ad-hoc but i would like it to work with infrastructural devices also i do have some spare routers available.
View 3 Replies View RelatedWhen I click on to my wireless network list nothing shows up, but I use my work pc and about 20 networks show up. What is going on with my lap top.
View 1 Replies View RelatedIm working for a client at the moment and I've had to setup a network printer for them, I've got 4 Windows 7 machines easily printing over the network to this printer that is connected wirelessly but they want one of there machines to use the scanning functionality of the printer.The scanner doesn't show up at all in the local network devices like the printer does and to be honest i don't really have any experience with scanning over a network to a windows 7 machine, but this printer does support scan to ftp so my idea is to setup a small ftp server on the windows 7 machine with a folder to stored scans on the desktop or something, then put the details of the server in to the printer making it as easy as possible for the customer to scan stuff and just get it from the folder on the desktop, i could also share this folder over the network for anyone to open and get a scan if needs be.
View 2 Replies View RelatedMy entire floor receives wifi from a D-Link router box. For the first 4 months, my laptop was able to find and connect to our wifi fine. Last night the internet crashed. All of my German housemates have internet again, but my laptop does not show the network anymore. My wireless card picks up all the other signals in range, but not our router's. I can only get internet with an ethernet cable.
View 1 Replies View RelatedI put Win7 on a customed pc bought online. The motherboard has an Atheros L1 integrated NIC and I installed a Dlink dge530t NIC into a PCI slot. I know I have to disable the onboard nic but the installed card is not comming up either in Device manager or network connections. What gives? In the bios under integrated peripherals i did enable PnP OS.
View 4 Replies View Relatednetwork adapter does not show up under device manager windows xp
View 4 Replies View RelatedThis is the configuration I am running:Internet > Cable Modem > Netgear WNDR3700 Router ~~ DAP-1522 > Wired Windows 7 PC + Linux PC + Printer.The Windows 7 and Linus PC's do communicate well to the internet as do any laptops accessing the router wirelessly and any devices wired to the router. That is the good news.
The bad news is that any devices located after the DAP-1522, including the DAP-1522 do not show up on the network map of either the router or any of the wireless laptops. Neither does the Win 7 PC connected through the DAP-1522 show any networked devices, whether through the DAP-1522 or not, even though network discovery is turned on.
Right now the DAP-1522 is set up to function as a bridge and is in "Static IP" mode. I tried changing it to DHCP, but the DAP-1522 will not allow saving that setting, even though it will allow changing it. It just reverts back to "Static IP". The firmware version is 1.31, and the firmware update went well after a workable logon to the admin page was discovered. Also the one-button (WPS) set-up to the router worked as far as allowing an internet connection.
What needs to change to allow all the devices to show up on the network maps and maintain internet access? Ultimately, I would like to stabilize the IP's of the major components of the network to make troubleshooting easier. But to do that the devices need to show up on the network maps, particularly of the router, so they can be added to the IP reservation table by selection.