Link 2 ISP Circuits Into A Single Home Network
Jul 3, 2011
I have 2 internet services with separate ISPs. My local telephone exchange is somewhat dated so the maximum speed per ISP/connection is about 1 Gbps. I have streaming radio services, I do quite a bit of file downloading and there multiple devices currently trying to share a single connection. I haven't been able to utilise the second connection because my NAS and print serving is all configured on the first connection and therefore unavailable to users/services on the second connection.My goal is to utilise the available capacity of both connections but at the same time allowing all network resources (file and printer sharing, NAS drives, etc.) to be available jointly to all network clients.
My first router is a Netgear RangeMax ADSL modem/wireless router (DG834PN). This connects directly to one ISP and has the NAS and printers attached. The second router is a Netgear N600 wireless dual band router (WNDR3400) which attaches to a Linksys ADSL 2 Gateway with 4-port switch (AG241 v2) and then to the second ISP.As an aside, I also have a number of Devolo devices for utilising the electrical circuit for networking purposes. I have a dLAN 200 AVmini adapter connected to the RangeMax router with 2 further dLAN 200 AVmini adapters and a dLAN 200 AV wireless N adapter distributed through my house.
View 2 Replies
ADVERTISEMENT
Feb 1, 2011
I have a site which has been successfully running a multilink bundle of four T1 lines for about 6 months. The remote location is a C3825 router and the central location router is a C7206. I have access to both. A few weeks ago the multilink circuit started flapping and I was able to identify one of the four T1 lines as the culprit. When I shut down the interface for that one T1 line, the multilink circuit stops bouncing. As soon as I issue a "no shut" command on that fourth T1 interface, the multilink circuit starts flapping, ping commands start to time out and I have to shut it down again. The Telco has sent a technician to both locations and reported all tests run clean. Internal wiring from the NIU to the router has also tested fine. I've tried to move the T1 lines to different ports on both routers and the problem persists. [code]
View 9 Replies
View Related
Jun 18, 2012
I am in the process of acquiring a static ip address from my isp time Warner. I only want to pay for a single static, but I have a number of machines I want to put on the internet, a web server and a e-mail-server. Using a cisco router, a Cisco Rv 120w. Can I assign the static ip address my isp gave me to the Rv 120w and then crate a vlan to assign addresses to various computers. Or is this something my ISP does. I get the impression from the tech guy at Time Warner that this is something they do.
View 11 Replies
View Related
Sep 10, 2011
I have a D-Link DGL-4500 router and my landlord recently ungraded our internet connection. However, now I get this error message when I try to hook it up to the ethernet hub,"The addressing of the Internet side learnt thru DHCP conflicts with the addressing selected for the LAN side. Internet communications will be disabled until you have changed the LAN side addressing to resolve the problem."
View 3 Replies
View Related
Nov 25, 2011
I have a standard home network consisting of internet access provided by my cable company which is then disseminated to a variety of wired and wireless devices via a router.
I would like to create a second wireless network that is separate from my current one. This new wireless network would have extra access controls including access restrictions to some web sites using both IP address restrictions and using the OpenDNS DNS servers.
The picture below illustrates the current configuration. The question is: how can I connect ROUTER B to the internet using my current equipment (without buying another IP address from the cable company)?
W
MODEM --> ROUTER A --> ANTENNA <------> COMP 3
1 2 3 4
| |
| |
COMP 1 <---' | W
| ?? <--> ROUTER B --> ANTENNA <---> COMP 4
COMP 2 <-----' 1 2 3 4
W = WAN port
So, in the above picture, COMP 4 is connected via wireless to this second network and cannot access anything on the first network and uses different different DNS servers.
In case it matters, ROUTER A is a Linksys WRT54GL while ROUTER B is a D-Link DI-624.
View 1 Replies
View Related
Jul 29, 2011
I have a VWIC2 running two T1 circuits to two locations. Can I put the controllers on the same channel group? I also have a PPP multilink controller on a VWIC2 on channel group 0.
View 2 Replies
View Related
Apr 7, 2011
Camera set up with the Beta Mac wizard connected via ethernet on Airport base. Wireless security WPA2 Personal. Using DHCP. AirPort Utility 5.5.2, OSX 10.6.6.I can see the cam with the myDlink Lite iPhone (4) App when I am in my house with my wireless network. When I am out, away from my network, the App can't connect to the cam, tells me to check my network settings. I did the wps way and added the cam in the airport base utility *Access Control* tab but still doesn't work. Checked in the cam web page settings, can't figure out what the Pre-Shared Key is and where I get it/set it up in the airport utility...
View 1 Replies
View Related
Sep 25, 2011
I want to create a link between two homes about 10/15 miles away from each other. I was thinking about using microwave technology to achieve this. I would like to be able to use this connection for linking two home networks/internet and possibly running iptv and voip over the link. I was hoping to operate in the unlicensed frequency.
View 2 Replies
View Related
Mar 3, 2011
I recently purchased a HP PHOTOSMART D110 wireless/eprint all in one. I have the dir-615 router and cannot get the printer to show up on my home network.Printer works fine hard wired to pc but wireless not at all. The ip address of the printer is 169.254.147.xx while everything on my network is 192.168.0.xx. Printer says connected for a few seconds then disconnected....I have tried to configure it on a vista and a win 7 machine.Everything else shows up fine on my network, as a matter of fact a friend brought his laptop over and it connected great..
View 14 Replies
View Related
Feb 14, 2013
can i configure virtual circuits on cisco layer 2 switch catalyst 2950 ?
View 1 Replies
View Related
Jul 23, 2011
I have tried to open ports, but if I use the [URL], I just get the closed. I have tried to use the Viritual server function, but can`t se to get it open.
On my old, D-Link I also had something cal port forwarding, this is not here. Here is a link to an emulator of the router: [URL]
View 13 Replies
View Related
Nov 20, 2011
What device would be necessary to link two networks of identical type? What devices would be necessary to link two networks of dissimilar types?I would say a network card and HUB for identical type but I do not know if this is correct?Describe the parameters governing the choice of cable type for a given network. What are the three main types of cables used in computer networks?
View 3 Replies
View Related
Jan 8, 2013
I have a TP-Link TL-WR720N wireless router, and I am trying to set it up so that it limits the times that my kids can access the internet. I have included screenshots of all of the programming pages, so you can see exactly what I am looking at. Here is what I have done so far:
Schedule: I created several schedules for different days, weekdays, weekends, start at 1900, end at 2100, etc.
Host: I created a host name titled "All", and set it for 192.168.0.3 ~ 192.168.0.199. The router assigns from 192.168.0.2 thru 192.168.0.199. I assigned my computer's MAC address as the "Parent PC", and bound it to 192.168.0.2, through the "IP and MAC Binding" function. In this manner, I hope to limit the kids access, while allowing the parent PC to access it at any time.
Rules: I selected the option to "Allow" passing of packets during these hours. I then created rules, assigning the host "All" to the different schedules that I created. I set the target as any, and did not set up any targets in the target section, because I do not want to control what sites they visit (yet, anyway). I generally don't worry about the sites they visit, I just think they spend too much time on the internet.
Here is what happens. I use my laptop (not the parent PC) as a test machine. When trying to access the wireless, i have verified that the router does give me an IP address within the specified range I created in the schedule. If I set the Access Rule to "Allow" the packets to pass through the router, and try to connect during the time it is set for, it will not allow my laptop to even connect. The weird thing is, if I set it for "deny", I can connect, but I have no internet access. Either way, if I have any of the rules enabled, I cannot access the internet at all. Thinking maybe there was some sort of conflict with schedules, I tried enabling only one of the rules instead of all of them, with no change.
What am I doing wrong? Do I need to set targets? If so, does this mean I have to set one for every site I want them to be able to visit? Can I set a target as the IP address of the router? If so, what ports do I use?
View 1 Replies
View Related
Feb 23, 2011
I've been trying to set-up DMZ for my DSL-2542B-SE_1.00_06112008.
But the problem is when I access my IP from WAN, It connects to Router Control Panel, I have set DMZ IP as 192.168.1.2 which is the my computer where I have the Server set-up.
Now I've disabled DMZ but still I can access to my router from WAN through my IP.
View 2 Replies
View Related
Aug 12, 2011
i have a little network knowledge but the tp-link wa-500g is proving quite a challenge to set up.i am trying to set it up in client mode to use with the xbox 360.thhe problem is i seem to set everything up correctly but it doesnt actually seem to work or to connect to the main router..which is a sky sagemfast router...(could this maybe be the problem? and if so how could i sort this? i have set a static ip on the tp.link and set up in client mode and "supposedly" connected to the main router in which is hard to figure out if it has or hasnt...also my sky router has wpa security and i am wondering if something has to be configured in my tp-link wa-500g to connect? but i can find no information on this needing to be done.
View 3 Replies
View Related
Jan 25, 2012
I accidentally created a home network and want to remove it, as it blocks all my wireless devices.
I have a dir655 with 2.o firmware
Os on computer I set it up on is win 7 64 bit
How to make other wireless devices easily recognize it? when I try to access it the wireless computers ask me for code that I entered on setup that was printed on bottom of router but system doesn't recognize it.
View 1 Replies
View Related
Jun 19, 2011
I recently decided to buy a DIR-655 router to create a wireless network in my home. I hooked it up last night and speeds look fine with my rr standard 10mpbs service. However, I decided to check the wireless status and my macbook, macbook pro, and my desktop computer are only getting at most 130mbps. Is there anything i can do to maximize this and go beyond 130mbps
View 3 Replies
View Related
Dec 4, 2012
I finally managed to set up this DSL modem / router on Sunday to replace my old Billion router. I set it up with DHCP and running on IP 192.168.1.254.Last night, the power tripped, and when everything came up again the entire network was dead - PC's were not getting IP's from DHCP.I connected a known working cable directly from laptop to router and attempted to access 192.168.1.254, nothing.So I reset the router and try again to the default IP 192.168.1.1. Nothing. Tried another PC, nothing.Restart router, try again, nothing. Plugged into my other router and try again, nothing. When I initially got the router I had the same problem until one day it just worked, still no idea why
View 2 Replies
View Related
Mar 22, 2011
I have the above router on 10.10.10.1 which I'm quite familiar with but I need reaching a VM residing on one of my internal MAC's. My cisco route table is as follows:
Gateway of last resort is 93.97.20.1 to network 0.0.0.0
93.0.0.0/21 is subnetted, 1 subnets
C 93.97.16.0 is directly connected, ATM0.1
10.0.0.0/24 is subnetted, 1 subnets
C 10.10.10.0 is directly connected, BVI1
S* 0.0.0.0/0 [1/0] via 93.97.20.1
The internal physical machine that contains the VM is 10.10.10.9 whose routing table is:
Routing tables
Internet:
Destination Gateway Flags Refs Use Netif Expire
default 10.10.10.1 UGSc 6 8 en0
10.10.10/24 link#4 UCS 5 0 en0
10.10.10.1 0:1b:2b:cc:7:8a UHLWI 7 1248 en0 284
10.10.10.9 127.0.0.1 UHS 0 86171 lo0
10.10.10.11 0:23:54:2a:6:d3 UHLWI 0 234 en0 150
10.10.10.30 0:9:34:28:60:2e UHLWI 0 25 en0 857
10.10.10.111 0:1d:ec:2:2d:2d UHLWI 1 1599 en0 721
10.10.10.255 link#4 UHLWbI 2 18609 en0
10.37.129/24 link#8 UC 2 0 vnic1
10.37.129.2 0:1c:42:0:0:9 UHLWI 1 2 lo0
10.37.129.255 link#8 UHLWbI 2 14046 vnic1
10.211.55/24 link#7 UC 2 0 vnic0
10.211.55.2 0:1c:42:0:0:8 UHLWI 0 2 lo0
10.211.55.255 link#7 UHLWbI 2 14046 vnic0
127 127.0.0.1 UCS 0 0 lo0
127.0.0.1 127.0.0.1 UH 5 214223 lo0
169.254 link#4 UCS 0 0 en0
The VM has a static IP of 10.211.55.5 and can obviously ping out to the rest of my lan but as of yet my router and other machines on the 10.10.10/24 subnet cannot reach the VM. I sort of presume this is a simple task of adding some kind of static route on my router and then all other machine will know how to get to the VM. So what do I need to do as I have about 40 or so customers already connected of whom I do not wish to suddenly halt their access due to my inexperienced attempts to create this route or new link(s)
View 1 Replies
View Related
Mar 28, 2012
I have been trying to get this setup for 2 days now and so far NADA.....
Router: Linksys E3000 - below is a list of all devices connected (hardwired T568B) to the 4 ports with a laptop connected via wireless
1. Main PC - motherboard: ASUS Maximus IV Extreme-Z (dual GB LAN ports)
2. Media Server - motherboard: MSI Z68A-GD80 (dual GB LAN ports)
3. Test Bench AMD PC
4. WD TV Live
Currently: I have all 3 computers running Windows 7 and connected to a Homegroup. I have given the correct permissions to enable sharing of files between each of the 3 computers and can transfer files from one PC to the next w/o any issues.
Desired: I want to connect my Main PC and Media Sever with a crossover cable using the 2nd LAN port on each motherboard, so that I don't have to go through the router to transfer data to and from these 2 PCs. I will have each PC also connected to the Linksys E3000 router via the 1st LAN port on each motherboard to supply the internet connection, so I am also not trying to "share" an internet connection between these 2 PCs. Basically, I want to run my home network through the Linksys E3000 and then a 2nd network for the 2 PCs using the crossover cable.
Current Problem: I disconnected the straight-through cables from the router to each computer from the 1st LAN port. I then connected the crossover cable from the Main PC to the Media Server and setup a new Home network in the Network and Sharing Center in Windows 7. Everything worked and I could transfer data to and from each these 2 PCs, so i know I wired the crossover cable correctly. Then I reconnected the straight-through cables coming from the router to the 1st LAN ports of each mobo, thinking that each PC would auto-detect the internet connection and reacquire my existing home network, enabling an internet connection again. However, this did not happen.
[URL] I also followed this how-to guide on microsoft.com, but when I get to Step 3 where it says that an "Unidentified network icon" will aprear in the Network and Sharing Center, it does not!
From Googling, reading, and troubleshooting I believe I know 2 things:
1. All of the hardware is functioning properly - when the straight-through cables from the router are disconnected, the 2 PCs are networked through the crossover cable and files can be transferred.
2. The problem is with Windows 7 somewhere - I think?
View 1 Replies
View Related
Jul 21, 2011
I am looking for an equipment recommendation for setting up an access point/repeater for my home network.
I have comcast > surfboard > d-link dir 655 I want to add another router/access point so I can move the dir655 to my office and have my computers connected over gigbait. All my comcast stuff is setup in the living room, and I would like to setup the access point there. Something like
comcast > surfboard > ddwrt n-router (living room) > dir655 (in office) > desktop
View 2 Replies
View Related
Nov 14, 2011
I have 3 pieces of hardware:
1. Green Packet DX-230 WiMAX modem with router
2. D-Link DIR-615 ver G2 (from my ISP)
3. D-Link 8 port desktop switch
I previously used the DIR-615 with my high speed broadband connection. However I had to move to a new house and here I can only get WiMAX. I want to...Place the WiMAX modem upstairs to serve as modem and wireless access point Have the DIR-615 function as the main router and firewall (downstairs) Use the switch to connect all the rooms in my house FYI my WiMAX modem has no connection configurations. I just plug it in and it'll connect automatically to the WiMAX signal. It has 2 LAN ports but no WAN port. From my understanding of networking, I have to turn off DHCP on my WiMAX modem, put it in the same IP range as my DIR-615 (192.168.0.100-199), and disable UPNP and NATPMP. After this I'm stuck.How do I tell my DIR-615 to use the WiMAX modem as it's WAN connection?Should I reserve an IP for the modem in my DIR-615?
View 3 Replies
View Related
Mar 22, 2013
I was using Remote Desktop between two home computers hard wired through the router and a switch. Now after upgrading to firmware 1.35 I can't get remote desktop to connect. I get an error that I may not have permission, etc. I have the DIR 655 ver A and am running Windows 7 professional on both computers.
View 5 Replies
View Related
Feb 24, 2013
I have a Time Warner Cable business class service with no static IP, with a wireless modem which is plugged to a CAT5 distribution panel. On the jacks (2 other rooms on the house) I have a Linksys E3000 and a Linksys Valet router for signal boost and gadgets usage (TV, cameras, etc).The main router (TWC) has it's own external IP which TWC assigns to me and internally distributes via DHCP the range 192.168.0.x. With that said:
- The E3000 has a 192.168.0.6 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address
- The Valet has a 192.168.0.7 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address
- The main router has the 192.168.0.1 as the gateway and web-interface
Whenever I connect something to the E3000, it is distributing the 192.168.1.x range and the valet 192.168.2.x range.That works perfectly for my home based business until I decided to use more stuff on the network such as a IP printer, IP cameras, etc.
- The IP cameras are connected to the E3000 due to signal strength and I have manually assigned them the 192.168.1.15 and 192.168.1.16 IPs and ports 9001 and 9002.
- The printer is connected to the E3000 and I have manually assigned the IP 192.168.1.30.
Issue 1: Port forwarding On the main router (TWC - UBEE) I have tried to setup a port forwarding by informing the Local IP as 192.168.0.6 (E3000 IP), Internal Port 0, Public Interface IP (0.0.0.0), Ext Start Port 9001, Ext End Port 9001, Protocol - Both, Enabled Yes. On the E3000 I did the same config (screen shot attached e3000.png).This is not working properly. I can't get into the camera.
Issue 2: Printer/ The printer is only accessible if I connect to the E3000 (because it is on the 192.168.1.x network)
Issue 3: How to configure all the devices on the same subnet? If I want everyone to be on the 192.168.0.x network, how to configure properly the E3000 and the Valet? I have tried to force them into the same network but it would not work properly. It would not get an IP from the UBEE router (main).
View 5 Replies
View Related
Jun 6, 2011
I have just bought a TP-Link Wireless Access Point (TL-WA&01ND) and an ethernet switcher (TL-SF2005D).I have put the access point into client mode, allowing me to put it in my room and wirelessly connect to my router, allowing me to plug my PC in over ethernet and use the internet. However, after much fiddling with settings I cannot get it to work, as it continually searches for a network, and then fails to connect, despite the fact it is configured to use the network?I already have a similar setup with a netgear wireless G access point which works, and so I dont understand why the new box cannot do this when using what I believe to be the same settings.
Secondly I have an ethernet switch box which I bought to connect to the access point and switch the ethernet signal between my two PCs, my xbox and PC. This works fine with my primary PC (over my old access point) but when I try to connect my PC i get a DNS failure with auto IP settings and a gateway failure with manual settings, and other devices refuse to connect.
View 9 Replies
View Related
Nov 20, 2011
My home desk top is set up with D-Link Xtreme N Dual Band Router. I have no problems accessing the internet on my desk top computer. I am trying to access my home wireless network through my HP laptop computer. The wireless network status is Limited or no Connectivity. I've tried the "repair" button with no resolution. The wireless connection is set to automatic.
View 1 Replies
View Related
Oct 20, 2011
Here's the layout: Cable modem in the basement. Several devices in which I'd prefer a wired connection in the basement. Upstairs on the 1st and 2nd floor of the house are many devices in which wifi is fine or preferred.Here's the problem: As you might guess, wifi is weak upstairs and certainly on the patio and 2nd floor. I have an access point upstairs that I've experimented with but it is flaky.
View 1 Replies
View Related
Nov 10, 2011
How to install a wireless network in home environment?
View 6 Replies
View Related
Jan 14, 2012
I am a new student in networking, taking the CCNA courses, and now want to rewire my home. I currently have a cable modem and E2500 setup running my network. I want to get the modem and router out of my computer room and in the basement where the cable enters the house. I want to do this to clean up the computer room wiring a bit and to run line drops to different rooms in the house where the internet will be utilized.Currently there are two PC's, a laptop, a tablet, sometimes a phone, and an XBOX using the internet. I want to get my printer back up and running on the network but thats another story. Only one PC is currently hardwired. I would like to run two cables into the room with the PC and XBOX that are currently using wireless, at least two into the computer room for the PC and network printer, and one or two into the living room for the blue ray player and possibly an internet tv.
View 1 Replies
View Related
Jul 14, 2012
I live in a Townhome complex so inSSIDer displays a lot of wireless activity. I have noticed that many of the routers channels are listed as 6 + 2, 4 + 1, etc., while show only a single channel. I have been able to "temporarily" replicate this by setting the Channel Width on my DIR-655, by setting channel width to auto, and when I am successful it displays a speed of 300, both in my task bar and in inSSIDer. However, that is usually short lived and the channel for my router reverts back to a single channel and the displayed speed drops to 130 or 144. My neighbor's Netgear is rock solid at displaying dual channels. Well, that and besting my signal strength. :-)
I have the router manually to channel 8 because none of the routers, judged by their displayed strength, use it.So, I guess my question is; how do I stop my DIR-655 from dropping back to using a single channel, which I interpret 20MHz, even though it is set on auto?
View 1 Replies
View Related
Dec 20, 2012
I have setup a webserver on my home PC and I have forwarded port 80 on my router to the IP adress of the PC that is running the web server. The web server is working great; I can get to my web pages from outside of my home by going to http://MyIpAddress/Anyway, the problem is with the Windows Media Player plugin I'm using. I want to embed 6GB MPEG-2 videos into my web pages. I have some videos on my PC and I want to be able to watch them remotely by connecting into my web page. It works fine when I'm at home; other PCs can connect and play the videos no problem. The problem is when I'm at work. When I'm at work, I go to my web page (via my IP address in a web browser) and the Media Player plugin says "Connecting" for a minute, then it says Ready, but the video will not play. I tried using a smaller, AVI file (680 MB) instead to see if the problem was streaming such a large file, but the video still would not play.Do I need to foward more ports on my router so that Windows Media Player can connect back and get the information it needs?
View 4 Replies
View Related
Oct 3, 2011
I have ADSL modem in my workplace that is connected to a switch and other workplace computers are connected to this switch so the ADSL internet is shared in LAN network.(in each of computer I set default Gateway to ip of modem .....)I want to dial my workplace from home and then use of workplace internet or connect to workplace LAN.(such as VPN or Port Forwarding or I don't know...)
View 11 Replies
View Related
Sep 20, 2011
I'm currently in the process of buying the new property, which is in the build process and would like to put some cables across 3 floors, which would be connected to the router downstairs.
View 3 Replies
View Related
