I accidentally created a home network and want to remove it, as it blocks all my wireless devices.
I have a dir655 with 2.o firmware
Os on computer I set it up on is win 7 64 bit
How to make other wireless devices easily recognize it? when I try to access it the wireless computers ask me for code that I entered on setup that was printed on bottom of router but system doesn't recognize it.
My home computer accesses the Internet through an ADSL modem and a phone line. I added a wired router (Linksys BEFSR41).I've since bought a laptop computer, an iPhone4 and a wireless router (Linksys WRT160N).Again, on the advice of a friend, I ADDED the wireless router, so now have two routers connected.The devices are connected as follows:
-Wall jack to ADSL modem
-ADSL modem to BEFSR41
-BEFSR41 to WRT160N
-WRT160N to desktop computer.
As I understand Linksys routers, the default IP address for ALL Linksys routers is 192.168.1.1.Both the iPhone4 and the laptop are unable to connect to the wireless router.I'm assuming the two routers are conflicting with each other, so I thought I would remove the wired router..Can I change the IP address of the BEFSR41 router from 192.168.1.2?
Would this resolve the conflict between the two routers and allow the wireless devices to "see" the wireless router? What's the correct procedure for removing the BEFSR41 router from the system?
Actually i have a small network of 4 and 5 computers. i am sharing internet via lan not ICS.there are some computer showing me in my network places coz i am using windows 7 and the other computers have same window. i can ping their computers by name and by ip add, which is assigned by DHCP. i can see thir MAC address. can i access their computer i mean their data or something else. i don't know that this is the right place to share such information or not.
View 14 Replies View Relatedi have 2 system in same network connected in same switch sys-1 have internet access & sys-2 no internet blocked from fire wall,....Now i want to use internet on sys-2 through sys-1 without Proxy or lancard sharing...
View 3 Replies View RelatedI have tried Intel tools and latest drivers ( w/ and w/o pro wireless utility) but cannot pass thru code 10 error. Tried uninstall and install....as earlier card 4965 agn worked fine but seems like some conflict is stopping successful 5300 agn driver install.
View 20 Replies View RelatedI have a 1Tb Iomega home media network drive. It normally connects via the network to all my machines (iMac osx, eee pc W7, ubuntu 10). But, something has happened, so now I can see the folders on the network drive but when I click on it (photos, videos etc), it says Windows cannot access \Iomega-0E10FDmovies
Error code: 0x80070043
The network name cannot be found
I have tried disabling the firewall in the router and the W7 eee pc, but nothing has worked.
In my home We have 3 pcs.
1. my personal PC1
2. home or general PC2
3. wireless PC (not important here.)so PC1 and PC2 are connected directly to internet via this [URL] modem router. I have full control over everything and I did setup the whole thing.We have a limited bandwidth internet plan, but a lot of bandwidth is easily used up by PC2.I want to limit the speed of internet access on that PC2 so that downloading becomes impossible or difficult.
I am redoing my homes networking and I am looking for a firewall. I heard that you can install clear os on a server and use it as a firewall and a dhcp server. So i was going to install it on a rack in my server cabinet. does the server need to have a wan port and a lan port? Or how does the server get connected? So, so far its the cable modem into the clear os firewall and then into my switch. Is is possible to use the clear os server as the dhcp server for the whole house? From the switch I am going to connect the rest of my servers, and the rest of the house. I was going to connect two wireless routers for my house. Would that work with the clear os server?
View 2 Replies View RelatedI've tried everything possible to connect my blu ray player to my network. I've tried the auto setup, manual entry and cant come up with anything. I've followed all the instructions i can find on-line and i don't know if I'm overlooking something or what. I've got Philips blu ray home theater system and linksys wrt120n router
View 5 Replies View RelatedI have a D-Link DGL-4500 router and my landlord recently ungraded our internet connection. However, now I get this error message when I try to hook it up to the ethernet hub,"The addressing of the Internet side learnt thru DHCP conflicts with the addressing selected for the LAN side. Internet communications will be disabled until you have changed the LAN side addressing to resolve the problem."
View 3 Replies View RelatedI'm donating a computer that was in my office network but would like to delete the office network. How do I do it?
View 2 Replies View RelatedWe have a home network setup. My HP Pavilion AMD Athlon 64 laptop running Vista, shares the printer with an older desktop, AMD Athlon 1600 XP. The printer is hooked up to the older computer that I am getting rid of. I assume I will have to install the software for the printer onto my laptop so I can use it. Is there anything else I should do? Other than removing all the files etc off the old computer.
View 3 Replies View Relatedyellow shield on network sign especially wireless network
View 2 Replies View RelatedCamera set up with the Beta Mac wizard connected via ethernet on Airport base. Wireless security WPA2 Personal. Using DHCP. AirPort Utility 5.5.2, OSX 10.6.6.I can see the cam with the myDlink Lite iPhone (4) App when I am in my house with my wireless network. When I am out, away from my network, the App can't connect to the cam, tells me to check my network settings. I did the wps way and added the cam in the airport base utility *Access Control* tab but still doesn't work. Checked in the cam web page settings, can't figure out what the Pre-Shared Key is and where I get it/set it up in the airport utility...
View 1 Replies View RelatedI have a HP 6530b Laptop, and on-board Broadcom NetLink Gigabit Ethernet adapter.When I remove my laptop from the docking station, I obviously lose Network connectivity, however, when I replace the laptop back (or even just plug in a cable directly), I cannot reconnect to the network until I reboot.When I open Network and Sharing Center (Win7), and click change adapter settings the adapter is missing from the list (after i have removed laptop from docking station).
View 1 Replies View RelatedI want to create a link between two homes about 10/15 miles away from each other. I was thinking about using microwave technology to achieve this. I would like to be able to use this connection for linking two home networks/internet and possibly running iptv and voip over the link. I was hoping to operate in the unlicensed frequency.
View 2 Replies View Related I have 2 internet services with separate ISPs. My local telephone exchange is somewhat dated so the maximum speed per ISP/connection is about 1 Gbps. I have streaming radio services, I do quite a bit of file downloading and there multiple devices currently trying to share a single connection. I haven't been able to utilise the second connection because my NAS and print serving is all configured on the first connection and therefore unavailable to users/services on the second connection.My goal is to utilise the available capacity of both connections but at the same time allowing all network resources (file and printer sharing, NAS drives, etc.) to be available jointly to all network clients.
My first router is a Netgear RangeMax ADSL modem/wireless router (DG834PN). This connects directly to one ISP and has the NAS and printers attached. The second router is a Netgear N600 wireless dual band router (WNDR3400) which attaches to a Linksys ADSL 2 Gateway with 4-port switch (AG241 v2) and then to the second ISP.As an aside, I also have a number of Devolo devices for utilising the electrical circuit for networking purposes. I have a dLAN 200 AVmini adapter connected to the RangeMax router with 2 further dLAN 200 AVmini adapters and a dLAN 200 AV wireless N adapter distributed through my house.
I recently purchased a HP PHOTOSMART D110 wireless/eprint all in one. I have the dir-615 router and cannot get the printer to show up on my home network.Printer works fine hard wired to pc but wireless not at all. The ip address of the printer is 169.254.147.xx while everything on my network is 192.168.0.xx. Printer says connected for a few seconds then disconnected....I have tried to configure it on a vista and a win 7 machine.Everything else shows up fine on my network, as a matter of fact a friend brought his laptop over and it connected great..
View 14 Replies View RelatedI have tried to open ports, but if I use the [URL], I just get the closed. I have tried to use the Viritual server function, but can`t se to get it open.
On my old, D-Link I also had something cal port forwarding, this is not here. Here is a link to an emulator of the router: [URL]
What device would be necessary to link two networks of identical type? What devices would be necessary to link two networks of dissimilar types?I would say a network card and HUB for identical type but I do not know if this is correct?Describe the parameters governing the choice of cable type for a given network. What are the three main types of cables used in computer networks?
View 3 Replies View RelatedI have a TP-Link TL-WR720N wireless router, and I am trying to set it up so that it limits the times that my kids can access the internet. I have included screenshots of all of the programming pages, so you can see exactly what I am looking at. Here is what I have done so far:
Schedule: I created several schedules for different days, weekdays, weekends, start at 1900, end at 2100, etc.
Host: I created a host name titled "All", and set it for 192.168.0.3 ~ 192.168.0.199. The router assigns from 192.168.0.2 thru 192.168.0.199. I assigned my computer's MAC address as the "Parent PC", and bound it to 192.168.0.2, through the "IP and MAC Binding" function. In this manner, I hope to limit the kids access, while allowing the parent PC to access it at any time.
Rules: I selected the option to "Allow" passing of packets during these hours. I then created rules, assigning the host "All" to the different schedules that I created. I set the target as any, and did not set up any targets in the target section, because I do not want to control what sites they visit (yet, anyway). I generally don't worry about the sites they visit, I just think they spend too much time on the internet.
Here is what happens. I use my laptop (not the parent PC) as a test machine. When trying to access the wireless, i have verified that the router does give me an IP address within the specified range I created in the schedule. If I set the Access Rule to "Allow" the packets to pass through the router, and try to connect during the time it is set for, it will not allow my laptop to even connect. The weird thing is, if I set it for "deny", I can connect, but I have no internet access. Either way, if I have any of the rules enabled, I cannot access the internet at all. Thinking maybe there was some sort of conflict with schedules, I tried enabling only one of the rules instead of all of them, with no change.
What am I doing wrong? Do I need to set targets? If so, does this mean I have to set one for every site I want them to be able to visit? Can I set a target as the IP address of the router? If so, what ports do I use?
I've been trying to set-up DMZ for my DSL-2542B-SE_1.00_06112008.
But the problem is when I access my IP from WAN, It connects to Router Control Panel, I have set DMZ IP as 192.168.1.2 which is the my computer where I have the Server set-up.
Now I've disabled DMZ but still I can access to my router from WAN through my IP.
i have a little network knowledge but the tp-link wa-500g is proving quite a challenge to set up.i am trying to set it up in client mode to use with the xbox 360.thhe problem is i seem to set everything up correctly but it doesnt actually seem to work or to connect to the main router..which is a sky sagemfast router...(could this maybe be the problem? and if so how could i sort this? i have set a static ip on the tp.link and set up in client mode and "supposedly" connected to the main router in which is hard to figure out if it has or hasnt...also my sky router has wpa security and i am wondering if something has to be configured in my tp-link wa-500g to connect? but i can find no information on this needing to be done.
View 3 Replies View RelatedI recently decided to buy a DIR-655 router to create a wireless network in my home. I hooked it up last night and speeds look fine with my rr standard 10mpbs service. However, I decided to check the wireless status and my macbook, macbook pro, and my desktop computer are only getting at most 130mbps. Is there anything i can do to maximize this and go beyond 130mbps
View 3 Replies View RelatedI finally managed to set up this DSL modem / router on Sunday to replace my old Billion router. I set it up with DHCP and running on IP 192.168.1.254.Last night, the power tripped, and when everything came up again the entire network was dead - PC's were not getting IP's from DHCP.I connected a known working cable directly from laptop to router and attempted to access 192.168.1.254, nothing.So I reset the router and try again to the default IP 192.168.1.1. Nothing. Tried another PC, nothing.Restart router, try again, nothing. Plugged into my other router and try again, nothing. When I initially got the router I had the same problem until one day it just worked, still no idea why
View 2 Replies View RelatedI have the above router on 10.10.10.1 which I'm quite familiar with but I need reaching a VM residing on one of my internal MAC's. My cisco route table is as follows:
Gateway of last resort is 93.97.20.1 to network 0.0.0.0
93.0.0.0/21 is subnetted, 1 subnets
C 93.97.16.0 is directly connected, ATM0.1
10.0.0.0/24 is subnetted, 1 subnets
C 10.10.10.0 is directly connected, BVI1
S* 0.0.0.0/0 [1/0] via 93.97.20.1
The internal physical machine that contains the VM is 10.10.10.9 whose routing table is:
Routing tables
Internet:
Destination Gateway Flags Refs Use Netif Expire
default 10.10.10.1 UGSc 6 8 en0
10.10.10/24 link#4 UCS 5 0 en0
10.10.10.1 0:1b:2b:cc:7:8a UHLWI 7 1248 en0 284
10.10.10.9 127.0.0.1 UHS 0 86171 lo0
10.10.10.11 0:23:54:2a:6:d3 UHLWI 0 234 en0 150
10.10.10.30 0:9:34:28:60:2e UHLWI 0 25 en0 857
10.10.10.111 0:1d:ec:2:2d:2d UHLWI 1 1599 en0 721
10.10.10.255 link#4 UHLWbI 2 18609 en0
10.37.129/24 link#8 UC 2 0 vnic1
10.37.129.2 0:1c:42:0:0:9 UHLWI 1 2 lo0
10.37.129.255 link#8 UHLWbI 2 14046 vnic1
10.211.55/24 link#7 UC 2 0 vnic0
10.211.55.2 0:1c:42:0:0:8 UHLWI 0 2 lo0
10.211.55.255 link#7 UHLWbI 2 14046 vnic0
127 127.0.0.1 UCS 0 0 lo0
127.0.0.1 127.0.0.1 UH 5 214223 lo0
169.254 link#4 UCS 0 0 en0
The VM has a static IP of 10.211.55.5 and can obviously ping out to the rest of my lan but as of yet my router and other machines on the 10.10.10/24 subnet cannot reach the VM. I sort of presume this is a simple task of adding some kind of static route on my router and then all other machine will know how to get to the VM. So what do I need to do as I have about 40 or so customers already connected of whom I do not wish to suddenly halt their access due to my inexperienced attempts to create this route or new link(s)
I have been trying to get this setup for 2 days now and so far NADA.....
Router: Linksys E3000 - below is a list of all devices connected (hardwired T568B) to the 4 ports with a laptop connected via wireless
1. Main PC - motherboard: ASUS Maximus IV Extreme-Z (dual GB LAN ports)
2. Media Server - motherboard: MSI Z68A-GD80 (dual GB LAN ports)
3. Test Bench AMD PC
4. WD TV Live
Currently: I have all 3 computers running Windows 7 and connected to a Homegroup. I have given the correct permissions to enable sharing of files between each of the 3 computers and can transfer files from one PC to the next w/o any issues.
Desired: I want to connect my Main PC and Media Sever with a crossover cable using the 2nd LAN port on each motherboard, so that I don't have to go through the router to transfer data to and from these 2 PCs. I will have each PC also connected to the Linksys E3000 router via the 1st LAN port on each motherboard to supply the internet connection, so I am also not trying to "share" an internet connection between these 2 PCs. Basically, I want to run my home network through the Linksys E3000 and then a 2nd network for the 2 PCs using the crossover cable.
Current Problem: I disconnected the straight-through cables from the router to each computer from the 1st LAN port. I then connected the crossover cable from the Main PC to the Media Server and setup a new Home network in the Network and Sharing Center in Windows 7. Everything worked and I could transfer data to and from each these 2 PCs, so i know I wired the crossover cable correctly. Then I reconnected the straight-through cables coming from the router to the 1st LAN ports of each mobo, thinking that each PC would auto-detect the internet connection and reacquire my existing home network, enabling an internet connection again. However, this did not happen.
[URL] I also followed this how-to guide on microsoft.com, but when I get to Step 3 where it says that an "Unidentified network icon" will aprear in the Network and Sharing Center, it does not!
From Googling, reading, and troubleshooting I believe I know 2 things:
1. All of the hardware is functioning properly - when the straight-through cables from the router are disconnected, the 2 PCs are networked through the crossover cable and files can be transferred.
2. The problem is with Windows 7 somewhere - I think?
I am looking for an equipment recommendation for setting up an access point/repeater for my home network.
I have comcast > surfboard > d-link dir 655 I want to add another router/access point so I can move the dir655 to my office and have my computers connected over gigbait. All my comcast stuff is setup in the living room, and I would like to setup the access point there. Something like
comcast > surfboard > ddwrt n-router (living room) > dir655 (in office) > desktop
I don't see any GPL code for the DIR-601 listed at [URL]. Is there any reason it is not listed?
View 3 Replies View RelatedI have been searching through the cisco docs for a while and i just cant seem to find this info. Can I run aironet 1600's with my wism running 7.0.116? Also, could I run my 1130 series ap's with a wism2? Basically, what is the minimum code level for a lightweight 1600, and what is the maximum code level for a lightweight 1130?
View 3 Replies View RelatedI have 3 pieces of hardware:
1. Green Packet DX-230 WiMAX modem with router
2. D-Link DIR-615 ver G2 (from my ISP)
3. D-Link 8 port desktop switch
I previously used the DIR-615 with my high speed broadband connection. However I had to move to a new house and here I can only get WiMAX. I want to...Place the WiMAX modem upstairs to serve as modem and wireless access point Have the DIR-615 function as the main router and firewall (downstairs) Use the switch to connect all the rooms in my house FYI my WiMAX modem has no connection configurations. I just plug it in and it'll connect automatically to the WiMAX signal. It has 2 LAN ports but no WAN port. From my understanding of networking, I have to turn off DHCP on my WiMAX modem, put it in the same IP range as my DIR-615 (192.168.0.100-199), and disable UPNP and NATPMP. After this I'm stuck.How do I tell my DIR-615 to use the WiMAX modem as it's WAN connection?Should I reserve an IP for the modem in my DIR-615?
I was using Remote Desktop between two home computers hard wired through the router and a switch. Now after upgrading to firmware 1.35 I can't get remote desktop to connect. I get an error that I may not have permission, etc. I have the DIR 655 ver A and am running Windows 7 professional on both computers.
View 5 Replies View RelatedI have a new computer but I can't connect to the D-link internet connection because I can not find my security code. Can I find the code somewhere in my old computer? If not is there any other way to get it?
View 2 Replies View Related