Cisco Routers :: Cannot Access The Web Management Interface Of SRP521W-U From A Different Subnet

Oct 30, 2012

i cannot access the web managemnet interface of this router from a different subnet.THe WAN interface is a 4G LTE connection,I have disabled both the SPI firewall and NAT and enabled remote management from any ip address but i cannot access the admin web page from a remote subnet.Doing a port scan of the routers WAN or LAN address i cannot see any ports open at all...its as if firewall or NAT is still enabled somehow.

View 0 Replies


ADVERTISEMENT

Cisco Routers :: Unable To Access SRP521W Web Management

Jan 26, 2013

Just brought another set of SRP521W, after changed the WAN setting to PPPOE, we unable to access the web management. The power/sys light will keep blink when trying to access the web management. We able to ping it. We tried the reset button but it did not work as well. Is that a way to upgrade the firmware without using the web management?

View 4 Replies View Related

Cisco Routers :: SRP521W - Wan Interface Disconnected While 3G Mobile Network Is Connected?

Apr 4, 2012

Using a 3G USB Modem (Huwaei E153) the mobile network status is connected however the Wan Interface (AutoConfiguration -DHCP) is displayed as Disconnected (Physical layer disconnected).

View 2 Replies View Related

Cisco Routers :: Configure Wi-Fi Guest Access For SRP521W-K9-G1?

Nov 24, 2012

I have one SRP521W-K9-G1 and need to provide guest internet access without access to my network. What is the best way to configure this?

View 3 Replies View Related

Cisco Switching/Routing :: SG 200-26P Cannot Access Web Interface From Different Subnet

May 24, 2012

Got a shiny new SG 200 26P which seems to work fine operationally.owever, when I am trying to access the web interface from a different IP subnet, the web brower just times out.If I put my PC on the same IP subnet, it works just fine. From the other subnet, I can ping the switch fine. The default gateway is set on the switch, and from the web interface I can ping and dns resolve other hosts and on the internet. I've tried to create a management profile to 'allow all from everywhere' basically, but still no luck.I'm completely stumped.  I've tried to reset to firmware defaults, and I'm now runinng the latest firmware. I woudl suppose that the switch would allow itself to be managed via the web interface from all subnets by default. Any thoughts?  The fact that the switch can ping internet hosts makes be believe it's own default gateway and IP are all ok and working.. (and I can ping it from anywhere in my network).

View 4 Replies View Related

Cisco Wireless :: AP1261N - Unable To Access Bvi Interface From Different Subnet

Apr 23, 2013

I can't access the bvi interface I use to manage the AP1261N from an IP address that is not in the same subnet of the bvi interface. The AP is configured as root bridge. Obviously I've the same behaviour for the non-root AP connected to it. For sure it's an ap configuration problem as other devices in the same vlan (vlan1) are reachable by the vlan I'm connected to. This is the conf:
 
version 15.2
no service pad
service timestamps debug datetime msec

[Code].....

View 13 Replies View Related

Cisco Wireless :: WLC 5508 7.3 Management Interface Access To GUI?

Jan 16, 2013

After I've upgraded software to the v7.3 and applied AP-SSO it made imposible to access the controller's gui via Service-port. So we tried to access it by management-port, but there is some problem too. It is not working from another subnets. But default gateway on management vlan is set correctly and I even tried to turn of all acl's on switch. WLC is only accessible from the same network. But at the same time wlc is replying on ping fine.All other protocols cannot connect to the controller.

View 3 Replies View Related

Cisco :: 5508 - Unable To Access Controller Using Management Interface

Apr 3, 2013

I configure IP address on the management interface port 1 of 5508 controller when i connect it direct to my laptop i can't ping or access controller from my laptop even i connect through layer 2 switch still i can't not.
 
IP Address of management interface : 10.21.0.50
Laptop IP Address : 10.21.0,51

View 13 Replies View Related

Cisco Firewall :: Provide Access To The Management Interface / Vlan On ASA 5505

Jun 8, 2011

I've got an ASA 5505 running 6.3 I've connected the management interface to our management vlan (which contains switch IPs, ilo's etc)Is there a way to allow access to this vlan from another?

View 1 Replies View Related

Cisco Switches :: SRW224G4 - Cannot Access Web View Management Interface Through IP Address

Jul 12, 2012

I am the Systems Admin at LDM Media and am trying to get some support for one of the SRW224G4 managed switches we have in our rack. The issue is as follows:

Any endpoint connected to the switch is assigned an IP address in the range of 169.254.154.XXX regardless of the switches set IP range, the second issue is that I cannot access the web view management interface through the default IP address 192.168.1.254 (and I have tried to use the last IP in the range set by the router 169.254.154.254, to no avail)
 
How to regaining control of this supposedly smart switch?

View 3 Replies View Related

Cisco Routers :: RVS 4000 HTTP Management Interface Hangs At Port 80 And DHCP Stops Working

Dec 1, 2012

This is the RVS 4000

Firmware version 1.3.3.5
STAR 9202 Chipset
64 MB DRAM
8MB Flash
 DOS, Block WAN Rq, Remote mgmt all OFF
IPSec Tunnel none used

[code].....
 
Every day or so the Router becomes unresponsive to the HTTP mgmt interface, as well as it no longer offers DHCP services.then this happens the only remedy is to power reboot.

Everything comes back online just fine, however, the LOGS are initilaized so no data to figure out what`s going on.My next step is to setuo a syslog server and have the logs copied out.(  No, I have no Torrents running at all, but I do have several devices like AppleTV, PS3s etc that run streaming Video plus I have the SPA3102  )

View 1 Replies View Related

Cisco Routers :: WAN Port On SRP521W

Mar 14, 2011

We've come across an issue whereby the WAN port fails to light up with an Adtran Total Access 832 (via bonded SHDSL) unit.
 
Eventually the WAN port does light up after connecting and disconnecting it several times with the ethernet cable. However as a test I power cycled the router with the WAN cable disconnected and had a strange issue where the WAN light would constantly flash and show up in the web gui as being connected when in fact the Adtran Unit showed the device was not connected at all.
 
This is the second Cisco SRP521W router in place as the original one disconnects overnight without any load and a power cycle would fix the issue, but this replacement router disconnects during business hours (even worse for the customer) and power cycling does not bring it back online. We've adjusted the WAN port to 10MB Full on both devices and hope that it stays up. I am wondering if any has had a similar experience?  Would this be a behaviour of a faulty unit or may it not be compatible with the Adtran Total Access 832 (via bonded SHDSL) unit perhaps?

View 1 Replies View Related

Cisco Routers :: SRP521w - Connection With CCA V3.2

May 21, 2012

I have a problem in connecting SRP521w with CCA v3.2. I tried to connect the device with CCA but it said that that the device is unsupported. I already upgraded the router's firmware with v1.01.26.
 
Here is what the CCA looks like every time I try to connect with the router  :

View 1 Replies View Related

Cisco Routers :: SRP521w - VPN Configuration

Jul 2, 2012

Cisco srp521w router vpn configuration. company has wan static ip to router. enable vpn Cisco server in router. connected with Cisco vpn client.  route failed in log. Need to access a PC on the company site with address 192.168.15.105 and router with gateway 192.168.15.1.

How do i configure ip pool ? different ip address? if i connect how do i access pc 192,168.15,105 ? remote pc with 192.168.1.100.

View 2 Replies View Related

Cisco Routers :: Auto-attendant Or IVR In SRP521W?

May 26, 2012

I have a router SRP521W I wonder if you can setup a self-attendant or ivr to this device.

View 4 Replies View Related

Cisco Routers :: SRP521W - Default Route Through VPN?

Mar 18, 2012

Is it possible to send all traffic through site to site VPN using SRP521W (on the other site ASA) ? Lets say, traffic to Internet from branch through HQ - site to site VPN between branch and HQ. I've tried to set up destination crypto policy entry to 0.0.0.0 0.0.0.0 but it's not accepted. Firmware version is 1.01.26 (003)

View 4 Replies View Related

Cisco Routers :: SRP521w Ethernet Sub Interfaces On WAN?

Aug 28, 2012

Have followed the admin guide, and can setup this up fine, however what we're wanting is to turn off any IP connection for the main wan ethernet interface and only have the sub-interface have an IP connection method.
 
I can't see how you can turn this off, which is causing a double-up of dhcp requests being sent when using both the main/sub ethernet interfaces to use dhcp.
 
This has been tested on the 521w and 521w-u versions, and I've just used the latest firmware 1.2.4 on the u version.
 
How can this be configured so that there is only 1 WAN interface that is using IP (the sub interface) Setting default routes to point to the sub interface doesn't make a difference.

View 3 Replies View Related

Cisco Routers :: Configuration Template For SRP521W

Nov 3, 2010

Any recommendation for creating a configuration template for the SRP521W?  I can use the Admin-->Backup Config to get a xxx.cfg file, but I cannot edit it with notepad++. Also, i know the config can be view via view-source: [URL], but how would I load a modified copy of this back to the router?

View 8 Replies View Related

Cisco Routers :: Create VPN Between SRP521W And UC560

Jun 9, 2011

I am trying to create a VPN between a SRP521W (only point-to-point VPN) and a UC560 (VPN server) and it seems it doesn't works (SRP doesn't create the tunnel).

View 4 Replies View Related

Cisco Routers :: SRP521W Falling Short

Feb 25, 2013

We have been using a SRP521W as the main Router for an office with about 25 users.
 
So on the cable network it's about 25 computers, 25 IP Phones, 3 printers. Wireless network hold some smartphones and tablets. Computer traffic is 100% Remote Desktop.
 
That said, for the last few days network connectivity sucks. I think the problem is, precisely, the SRP521W. Some mornings the WAN link is down and can only be brought up by a router reboot.
 
There's an IPSec tunnel to HQ.
 
Wireless network was moved recently to a WAP121 to offload the SRP521W. It has two networks: internal and customers with two VLANs.
 
CPU Usage is around 30-45% all day and spikes to 100% sometimes. RAM Usage is 40-45%. I do not know if this is "too much", "average" or "really low load".
 
Anyway, time for questions:
a) How can I get a table of active connections on the firewall/NAT to see if there anything "strange" on the network traffic that maybe causing issues?
 
b) Is there any know bug in the VLAN handling of the SRP that maybe causing the issue? (it's one of the latests changes introduced).
 
c) If the problem is that there's too much load for such a small router, what replacement would you recommend given the details above? (remember I do not really need wireless on the router as I have the wap121).

View 3 Replies View Related

Cisco Routers :: RV042 - VPN Access Resources With Same Subnet?

Aug 24, 2011

I have an RV042 with the PPTP server configured, which is working because I can connect with my iPad and droid phones, however, I'm unable to access resources on the RV042 side (192.168.1.X) when my local network is the same ip scheme (192.168.1.x). It works fine when I'm on a different network like 3G or someone else's Wifi network (192.168.11.X).

View 1 Replies View Related

Cisco Firewall :: Management Of ASA5520 From ITsupport Subnet?

Sep 27, 2012

Currently have an ASA5520, management port is set to management only connected to a management vlan, inside, outside and dmz ports also in use for respective traffic, all is working well, the issue i have is that the ITsupport staff on there user vlan have to have access to manage the ASA with ASDM at all times, this all works fine as i have added a route for management to there subnet, problem is that from this vlan they can no longer ping the remote sites which connect via site to site vpn. For troubleshooting and management purposes this is required, is there any way around this?, if we make the management port not management-only how will this effect other traffic or routing?

View 3 Replies View Related

Cisco Routers :: RV220W PPTP Users Unable To Access Subnet Across Tunnel

Apr 21, 2012

I have two offices connected with an IPSEC VPN tunnel using RV220W routers.  The Tunnel works fine for local users between the two sites(Site 1:10.0.0.x; site 2 is 10.0.2.x).  I have also set up PPTP users for remote access.  PPTP users that connect to site 1 cannot access site 2 and vice versa.   The PPTP users have no trouble accessing the resources on the site that they connect to.  I have tried activating RIP and adding various static routes with no success.  If I PPTP connect to site 1 and I tracert to an IP address on site 2 the route goes to the site 1 router and then goes to the internet(connected to the site 1 router) where it stops.

View 2 Replies View Related

Cisco Routers :: SRP521W VPN Site-to-Site Tunnel Doesn't Establish

Dec 19, 2011

As you can see i have problems with connecting 2 SRP521W together for an VPN tunnel. I tried as much as I can but now i dont know what to do or how and where is the mistake? the connection between these two devices was there last week, after weekend (nothing changed in configs) the connection suddenly was interrupted, without any reason or warning. another day it worked again and 20 mins later connection was dead again...and now it wont establish at all.. here are some screenshots from the vpnconfigs of my devices. one has a static IP the otherone uses FQDN. These are the IKE policies: Here the IPsec Policies: and the GRE policies:

View 10 Replies View Related

How To Subnet A Serial Interface

Sep 7, 2011

IP Address : 192.168.1.0 /24

I need 50 hosts

I need to subnet for f 0/0 and s 0/0

I know for f 0/0 its 192.168.1.1 /26, but after hours and hours i can't seem how to subnet for the s 0/0

View 2 Replies View Related

Cisco :: Separate Interface For Management On ASA

Nov 5, 2012

I'm trying to separate my management traffic from regular traffic by splitting the management and "outside" interface to separate vlans but I'm hitting a routing issue. Say I have have a management network of 192.168.1.0 255.255.255.0 running across vlan 1 and I want to use 192.168.2.0 255.255.255.0 running across vlan 2 for the outside interface to send all the other traffic excluding the management traffic across. Tag both vlans on the external interface, say Eth0/0 Default route of route outside 0.0.0.0 0.0.0.0 192.168.2.1, With this, you can not hit the management interface because there is no route defined for the 192.168.1.0 network. However of course if you try to set one, you'll get the "connected route exists" error. How can I set the default route or gateway of the 192.168.1.0 network on the ASA. Switches just don't complain like the ASA does.

View 8 Replies View Related

Cisco :: 6509 Sup-2T Management Through CMP Interface

Dec 3, 2012

We acquired recentlty a new Cisco 6509 with Sup-2T supervisor card
 
My question is the following : we have a management subnet on a Copper-based switch; we manage all equipments through this network. I planned to configure the management interface on the 6509 to connect this switch & monitor the VSS through it However, since it is a CMP interface, most of the actions (SNMP, IOS upgrade.. won't be possible through this link)  Moreover, I don't think LMS would be able to get the configuration through it (except by configuring a script running "attach" command & show run
 
Is there something I miss or must I add another interface of the Catalyst to this network (the problem being that I have no copper line card)

View 2 Replies View Related

Cisco Routers :: SRP 527w Cannot Access Web Interface

Aug 3, 2011

Our SRP527W is working - internet on and SIP phones on but I cannot access the Web interface anymore. When I try to login from any of the machines around I get a "not responding" message.
 
Before I get to the stage where I have to reset the whole thing and re-do the configuration completely ? I tried powering off and powering on as well as restarting all the switches etc... but I get the same result.

View 1 Replies View Related

Cisco Firewall :: Changing Subnet Mask In An ASA5520 Interface

Aug 8, 2012

We have an ASA 5520, working fine.One of the interfaces is connected to users PCs and printers mainly. Last months the number of devices has grown rapidly, and we would like to make some changes in it in order for it to be able to host new devices.We thought on change subnet mask of actual subnet (10.0.2.0/24) to 10.0.2.0/23, so it can hold as many devices.I understand I have to make some changes in the ASA, but my question is:What will happend to the acces rules I have created?Will I need to create them again? There are some objects which carry information about subnet mask, so I suppose I will need to redefine them, but for those without any subnet mask information, will I have to redefine them?

View 2 Replies View Related

Cisco Wireless :: WLC 5508 / Cannot Create Interface As Same Vlan Id And Subnet

Aug 12, 2012

I have got a wireless project with WLC  main office and have 10 sites where ap's are there and ap's getting registerd .we need 4 ssid in all branches same .

ssid guest
ssid scanner
ssid user
vlan 600 main office for scanner 192.168.1.0
in branch
vlan 600 for scanner but ip is 172.16.1.0

and bgp is running . And customer is asking me not to edit the ip range or vlan or create new vlan . but in wlc am not able to create branch network 172.16.1.0 range interface and vlan 600 as vlan 600 i already created for scanner main office 192.168.1.0 So is there a way to do that .
 
Temprarly one site i did like created vlan 610 in branch no ip . And in main office interface vlan 610 given another ip range . and i created interface in wlc . from branch i can connect the ssid and getting ip . But they dont want to create any aditional vlan or another network . Customer dont have a smartnet contract . They recently baught 2 wlc 5508 and 40 ap 1142.

View 4 Replies View Related

Unable To Access My Routers Interface

Jun 6, 2011

I can't seem to be able to access my wireless routers settings on my iMac, whenever I type my router's ip adress in my browser's adress bar it's unable to connect. According to the network settings menu my router's ip adress is 78.21.0.1, I don't know if that has anything to do with it.

View 8 Replies View Related

Cisco WAN :: SRP 527W Web Management Interface Inaccessible

Jan 27, 2011

We have recently purchased a Cisco Small Business Pro SRP 527W router, all seems good and it is running smoothly, no disconnections or sync issues like our last router. However, after a certain amount of time the web management interface is unavailable through the browser (accessing it via 192.168.1.254 or the alternative we set-up 1.1.1.1) It is totally unavailable and timeouts in the browser yet there is still internet access and network is still alive. The web management interface was accessible before though and the only solution I have been able to do to access it again is to reboot this router.Could it be possible that because port 80 is forwarded to a different IP it interferes with the Web management interface? And how wcould the interface port access be changed?

View 2 Replies View Related

Cisco :: WLC 2006 - AP Connecting To Management Interface?

Jun 7, 2011

I have running a Wireless LAN Controller Cisco 2006.Today my management IP its public with Internet access. I am thinking in use a private IP without internet access. I have certains Access-Points in other building, that connect to AP Manager interface using Internet . When i see the tcp connections, i look that the access-point not only have TCP connections to AP Manager interfaces, it have TCP connections to Management interface too!!!.If i shutdown the connection between Management interface and Access-Points (mantaining the connection between Access-Point and AP Manager interfaces)?

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved