Cisco Routers :: Create VPN Between SRP521W And UC560
Jun 9, 2011I am trying to create a VPN between a SRP521W (only point-to-point VPN) and a UC560 (VPN server) and it seems it doesn't works (SRP doesn't create the tunnel).
View 4 Replies
ADVERTISEMENT
Cisco Routers :: WAN Port On SRP521W
Mar 14, 2011We've come across an issue whereby the WAN port fails to light up with an Adtran Total Access 832 (via bonded SHDSL) unit.
Eventually the WAN port does light up after connecting and disconnecting it several times with the ethernet cable. However as a test I power cycled the router with the WAN cable disconnected and had a strange issue where the WAN light would constantly flash and show up in the web gui as being connected when in fact the Adtran Unit showed the device was not connected at all.
This is the second Cisco SRP521W router in place as the original one disconnects overnight without any load and a power cycle would fix the issue, but this replacement router disconnects during business hours (even worse for the customer) and power cycling does not bring it back online. We've adjusted the WAN port to 10MB Full on both devices and hope that it stays up. I am wondering if any has had a similar experience? Would this be a behaviour of a faulty unit or may it not be compatible with the Adtran Total Access 832 (via bonded SHDSL) unit perhaps?
Cisco Routers :: SRP521w - Connection With CCA V3.2
May 21, 2012I have a problem in connecting SRP521w with CCA v3.2. I tried to connect the device with CCA but it said that that the device is unsupported. I already upgraded the router's firmware with v1.01.26.
Here is what the CCA looks like every time I try to connect with the router :
Cisco Routers :: SRP521w - VPN Configuration
Jul 2, 2012Cisco srp521w router vpn configuration. company has wan static ip to router. enable vpn Cisco server in router. connected with Cisco vpn client. route failed in log. Need to access a PC on the company site with address 192.168.15.105 and router with gateway 192.168.15.1.
How do i configure ip pool ? different ip address? if i connect how do i access pc 192,168.15,105 ? remote pc with 192.168.1.100.
Cisco Routers :: Auto-attendant Or IVR In SRP521W?
May 26, 2012I have a router SRP521W I wonder if you can setup a self-attendant or ivr to this device.
View 4 Replies View RelatedCisco Routers :: SRP521W - Default Route Through VPN?
Mar 18, 2012Is it possible to send all traffic through site to site VPN using SRP521W (on the other site ASA) ? Lets say, traffic to Internet from branch through HQ - site to site VPN between branch and HQ. I've tried to set up destination crypto policy entry to 0.0.0.0 0.0.0.0 but it's not accepted. Firmware version is 1.01.26 (003)
View 4 Replies View RelatedCisco Routers :: SRP521w Ethernet Sub Interfaces On WAN?
Aug 28, 2012Have followed the admin guide, and can setup this up fine, however what we're wanting is to turn off any IP connection for the main wan ethernet interface and only have the sub-interface have an IP connection method.
I can't see how you can turn this off, which is causing a double-up of dhcp requests being sent when using both the main/sub ethernet interfaces to use dhcp.
This has been tested on the 521w and 521w-u versions, and I've just used the latest firmware 1.2.4 on the u version.
How can this be configured so that there is only 1 WAN interface that is using IP (the sub interface) Setting default routes to point to the sub interface doesn't make a difference.
Cisco Routers :: Configuration Template For SRP521W
Nov 3, 2010Any recommendation for creating a configuration template for the SRP521W? I can use the Admin-->Backup Config to get a xxx.cfg file, but I cannot edit it with notepad++. Also, i know the config can be view via view-source: [URL], but how would I load a modified copy of this back to the router?
View 8 Replies View RelatedCisco Routers :: SRP521W Falling Short
Feb 25, 2013We have been using a SRP521W as the main Router for an office with about 25 users.
So on the cable network it's about 25 computers, 25 IP Phones, 3 printers. Wireless network hold some smartphones and tablets. Computer traffic is 100% Remote Desktop.
That said, for the last few days network connectivity sucks. I think the problem is, precisely, the SRP521W. Some mornings the WAN link is down and can only be brought up by a router reboot.
There's an IPSec tunnel to HQ.
Wireless network was moved recently to a WAP121 to offload the SRP521W. It has two networks: internal and customers with two VLANs.
CPU Usage is around 30-45% all day and spikes to 100% sometimes. RAM Usage is 40-45%. I do not know if this is "too much", "average" or "really low load".
Anyway, time for questions:
a) How can I get a table of active connections on the firewall/NAT to see if there anything "strange" on the network traffic that maybe causing issues?
b) Is there any know bug in the VLAN handling of the SRP that maybe causing the issue? (it's one of the latests changes introduced).
c) If the problem is that there's too much load for such a small router, what replacement would you recommend given the details above? (remember I do not really need wireless on the router as I have the wap121).
Cisco Routers :: Configure Wi-Fi Guest Access For SRP521W-K9-G1?
Nov 24, 2012I have one SRP521W-K9-G1 and need to provide guest internet access without access to my network. What is the best way to configure this?
View 3 Replies View RelatedCisco Routers :: Unable To Access SRP521W Web Management
Jan 26, 2013Just brought another set of SRP521W, after changed the WAN setting to PPPOE, we unable to access the web management. The power/sys light will keep blink when trying to access the web management. We able to ping it. We tried the reset button but it did not work as well. Is that a way to upgrade the firmware without using the web management?
View 4 Replies View RelatedCisco Routers :: Cannot Access The Web Management Interface Of SRP521W-U From A Different Subnet
Oct 30, 2012i cannot access the web managemnet interface of this router from a different subnet.THe WAN interface is a 4G LTE connection,I have disabled both the SPI firewall and NAT and enabled remote management from any ip address but i cannot access the admin web page from a remote subnet.Doing a port scan of the routers WAN or LAN address i cannot see any ports open at all...its as if firewall or NAT is still enabled somehow.
View 0 Replies View RelatedCisco Routers :: SRP521W - Wan Interface Disconnected While 3G Mobile Network Is Connected?
Apr 4, 2012Using a 3G USB Modem (Huwaei E153) the mobile network status is connected however the Wan Interface (AutoConfiguration -DHCP) is displayed as Disconnected (Physical layer disconnected).
View 2 Replies View RelatedCisco Routers :: SRP521W VPN Site-to-Site Tunnel Doesn't Establish
Dec 19, 2011As you can see i have problems with connecting 2 SRP521W together for an VPN tunnel. I tried as much as I can but now i dont know what to do or how and where is the mistake? the connection between these two devices was there last week, after weekend (nothing changed in configs) the connection suddenly was interrupted, without any reason or warning. another day it worked again and 20 mins later connection was dead again...and now it wont establish at all.. here are some screenshots from the vpnconfigs of my devices. one has a static IP the otherone uses FQDN. These are the IKE policies: Here the IPsec Policies: and the GRE policies:
View 10 Replies View RelatedCisco Switches :: CCA Not Seeing UC560 Switch
Aug 29, 2011Have deployed a few of these - and am truly frustrated that I cannot see then in the topolgy, let alone actually manage them. Why such a ubiquitous switch is not supported.
Even the SmartPort utility is useless - CCA (3.3.1 and earlier) gives an error saying a port is incorrectly configured (I pluggged it into an exp port on the UC560 as I gave up trying to get a working uplink to an ESW-540-24P).
The Smartport port function wants the exp port (on the UC560) to be configured as a "Phone/Desktop" - if I try to change it to a "switch", it refuses to accept it saying the "Macro is unsuitable - or similar"
Cisco Wireless :: How Many AP541s Are Supported Directly In UC560 Deployment
Oct 26, 2011Does Cisco have an official number of how many AP541s are supported directly by a UC560? these are standalones and I know they are configured in a max of 10 to a cluster, but how many clusters can you have? We are looking at a hospital installation with one UC560 and 25 AP541s.
View 2 Replies View RelatedCisco Wireless :: Configuring Guest VLAN On AP541N And UC560
Jan 27, 2011I have a AP541N connected to a UC560. We are currently configured for Wireless Voice and Data. We have added a Guest VLAN, but don't see where in CCA to secure the VLAN from accessing the other other two default VLANs.
Additional Info: AP541N-K9-1.7(2)UC560 15.0(1)XA2, RELEASE SOFTWARE (fc2)CCA 3.0
Cisco WAN :: SRP521W / QoS For 2Mb Connection?
Mar 28, 2011We recently switched from a ADSL2+ service to a 2Mb SHDSL link. Uploading images to our website is happening all day long, thus greater upstream bandwidth was required.
Our downloads are suffering somewhat, the upstream gets easily flooded and downloads start to trickle.
I have a SRP521W which has a few QoS options. The QoS Bandwidth control has upstream bandwidth set to 2048 Kbps. Now I don't know how to enforce anything. How to use the WAN strict high priority queue appriopirately.
The website has a static IP address, so I can target that in the rules to only use 80% of the bandwidth?Alternatively can I limit upstream traffic per user?
Cisco Routers :: RV042 Can't Create A Simple VPN?
Dec 18, 2012i'm trying to set up a simple VPN (client to Gateway), but i can't ! An SSL VPN or an IPSEC VPN, whatever..
The firmware of the RV042 is up to date, and i'm trying QuickVPN as a client vpn (also updated...)
My configuration details :
I'm in : 192.168.2.14 /24
My RV042 : 192.168.2.250 /24
And the VPN intend to connect me to : 192.168.4.x
[Code].....
Cisco Routers :: RV220W Can't Create 255.255.254.0 Subnet
Nov 8, 2012I'm trying to setup this router with my IP range 192.168.100.1 to 192.168.101.254 but if I try to enter a subnet mask other than 255.255.255.0 I get the error - Invalid subnet mask. It should be 255 for given class of IP address at 255.255.xxx.0.
Every other device on my network allows that subnet mask, why not this router, it's stopping access from my 192.168.101.x devices.
Cisco Routers :: Create VPN Between RV042 And ASA5505?
Feb 20, 2012I have a Cisco ASA 5505 and a Cisco/Linksys RV042. I would like to crerate a site to site VPN between them, and from what I've read it is possible. So I set up the connection on both routers but When I click on connect on the RV042 nothing happens. I've made sure that the encryption settings are the same on both routers but I can't get them to connect to each other. I think the problem may be with the RV042 as the ASA has other site to site VPN connections without any proble (although they are on other ASAs). I saw this thread [URL] but I'm not sure how to disable phase 2 on the RV042 or enable it on the ASA.
what setting I need to change on either router to make the site to site work?
Routers / Switches :: How To Create Network Between Two PCs
May 6, 2011Got two pc's, two routers and one switch, and two serial cables and I want to create a network.
View 4 Replies View RelatedHow To Connect 2 Routers LAN - WAN And Create Subnet
Sep 8, 2012I'm trying to connect two routers and create a subnet but failing due to a little knowledge but no real understanding! I've read the ultimate setup thread loads of times but can't get my setup to work.
Here's the setup I'm trying to build:
Internet -> Master ADSL modem/router (No NAT, no DHCP) -> Slave cable router (NAT, DHCP)
I want to connect 3 Xboxes to the master router with external IPs to avoid the whole "moderate/strict" NAT nightmare. Then I'll connect everything else (PCs, Macs, wireless devices etc) to the Slave router which will assign IP addresses and do the NAT thing. Both routers are Netgear N150s (master is ADSL, slave is Cable).
Here's what I've tried so far:
Master router:
All IP addresses supplied by ISP
Internet IP: xxx.68.160.143
DNS: xxx.xxx.3.xxx and xxx.xxx.6.xxx
Router IP: xxx.68.160.142
[Code].....
Cisco :: Create A Simulated Serial Wan Connection Between 2 Routers?
Apr 12, 2012i'm making up a new lab and need to create a simulated serial wan connection between 2 routers. I originally did it with 2 wic1t cards but i sold my old setup. I have access to wict1 cards i know they are serial connections. will it provide the same function as connecting with wic1t cards?
View 2 Replies View RelatedCisco Routers :: WRV200 - Create 3 Node WAN Using VPN Connections
Jul 11, 2012I have 3 WRV200 that I want to install in 3 cities.I want each router to have its own Internet connection from the local ISP.I then want each router to connect to the other 2 routers and create a 3 node WAN using VPN connections.
View 1 Replies View RelatedRouters / Switches :: Create A Public LAN Address?
Mar 7, 2011i want to connect dvr to the internet i need the step to take and process of creating a public LAN Address
View 1 Replies View RelatedRouters / Switches :: How To Create Password To Access One Pc To Other
Mar 2, 2011how to create a password to access one pc to another pc .like i have 3 pc it is connecting throw switch .ip addresss is 192.168.1.1,192.168.1.2, 192.168.1.3 i want access from 192.168.1.1 to \192.168.1.2 like this here i want to create login password and how to remove password
View 1 Replies View RelatedCisco :: Create A Bash Script To Log Into Routers And Make Config Changes?
Mar 7, 2012I am trying to create a bash script to log into routers and make config changes.I ran into a snag in that I am unable to pass a password for the ssh login.I tried tying an expect script to handle that piece but was unsuccessful.I saw on google something about public/private ssh keys (not the same type used to ssh into the box) but I do not want to go this route.Can this be done in another language other than a bash script?I would like to avoid TCL or EEM if possible, I want to learn a language that I can use for multiple purposes.
View 15 Replies View RelatedCisco Routers :: RV120W - Create New Unique Self-signed Certificate?
May 9, 2012how to create new unique self-signed certificate on RV120W? I can create request for singning by external CA, but I cannot create new unique self-signed certificate itself.
View 2 Replies View RelatedCisco Routers :: SRP541W Unable To Create IPSEC Policy To ANY (0.0.0.0)
Feb 26, 2012Unfortunately, it does not appear as if the SRP500 series will allow you to create an ipsec policy where the local or remote traffic selection is 0.0.0.0/0.0.0.0. It wants a specific network. I have a scenario where I want to send all traffic over the vpn tunnel.
Is there a workaround to this or a special way to input "ANY" as the remote network?
Cisco Routers :: Create Another Account With User Privileges In RV042 V3?
Jul 26, 2012I am just wondering if it is possible to have two user accounts in Cisco RV042 V3 (Firmware: v4.1.1.01-sp (Dec 6 2011 20:03:18). User accounts to mean that one user can access the router with an administrative level access can do all the changes and management of the router's configurations and settings while another user can only do viewing of the system summary tab and connect and manage the simple configuration to connection to the ISP in both WANs, like setting up the connection type and release/renew the ip address for dynamic ip assigned by the ISP DHCP server.
View 1 Replies View RelatedCisco Routers :: SRP547W Cannot Create Advanced Firewall Rules
Feb 27, 2012I have a SRP547W that I have configured the following way:
LAN 192.168.15.1/24 VLAN1
LAN 10.10.10.1/24 VLAN10
LAN 10.10.2.1/24 VLAN100
PPPOE ADSL
Software DMZ going to 10.10.10.x and another to 10.10.2.x - this is working OK
I now want to use the Advanced Firewall features to block all ports except those that I need as the software DMZ forwards everything. When I try to create the rules I get "the values are invalid" message no matter what I try.
I want to create explicit allow rules, followed by a deny all rule for each of the IP addresses used for the software DMZ
Have I got the Subnet Mask Correct for the Destination IP? Or should it be 255.255.255.0? It doesnt make a difference either way
Policy DetailsNameValueSource IP Address0.0.0.0Source Subnet Mask0.0.0.0Destination IP Address10.10.10.xDestination Subnet Mask255.255.255.254ProtocolAnySource PortAnyDestination Port443ActionPermitScheduleEverydayTimes24 Hours
Cisco Routers :: RV215W - Create Inbound Rules With Control Ip?
Apr 27, 2013I have a Cisco RV215W and i want to create inbound rule (wan -> lan) with ip control.I ha created in "service management" a new service (rsync on 873 start port and and port) After i had created a new access rules :
[code]...