Cisco Routers :: Configure Wi-Fi Guest Access For SRP521W-K9-G1?
Nov 24, 2012I have one SRP521W-K9-G1 and need to provide guest internet access without access to my network. What is the best way to configure this?
View 3 Replies
ADVERTISEMENT
Cisco Routers :: Unable To Access SRP521W Web Management
Jan 26, 2013Just brought another set of SRP521W, after changed the WAN setting to PPPOE, we unable to access the web management. The power/sys light will keep blink when trying to access the web management. We able to ping it. We tried the reset button but it did not work as well. Is that a way to upgrade the firmware without using the web management?
View 4 Replies View RelatedCisco Routers :: Cannot Access The Web Management Interface Of SRP521W-U From A Different Subnet
Oct 30, 2012i cannot access the web managemnet interface of this router from a different subnet.THe WAN interface is a 4G LTE connection,I have disabled both the SPI firewall and NAT and enabled remote management from any ip address but i cannot access the admin web page from a remote subnet.Doing a port scan of the routers WAN or LAN address i cannot see any ports open at all...its as if firewall or NAT is still enabled somehow.
View 0 Replies View RelatedCisco Routers :: WAN Port On SRP521W
Mar 14, 2011We've come across an issue whereby the WAN port fails to light up with an Adtran Total Access 832 (via bonded SHDSL) unit.
Eventually the WAN port does light up after connecting and disconnecting it several times with the ethernet cable. However as a test I power cycled the router with the WAN cable disconnected and had a strange issue where the WAN light would constantly flash and show up in the web gui as being connected when in fact the Adtran Unit showed the device was not connected at all.
This is the second Cisco SRP521W router in place as the original one disconnects overnight without any load and a power cycle would fix the issue, but this replacement router disconnects during business hours (even worse for the customer) and power cycling does not bring it back online. We've adjusted the WAN port to 10MB Full on both devices and hope that it stays up. I am wondering if any has had a similar experience? Would this be a behaviour of a faulty unit or may it not be compatible with the Adtran Total Access 832 (via bonded SHDSL) unit perhaps?
Cisco Routers :: SRP521w - Connection With CCA V3.2
May 21, 2012I have a problem in connecting SRP521w with CCA v3.2. I tried to connect the device with CCA but it said that that the device is unsupported. I already upgraded the router's firmware with v1.01.26.
Here is what the CCA looks like every time I try to connect with the router :
Cisco Routers :: SRP521w - VPN Configuration
Jul 2, 2012Cisco srp521w router vpn configuration. company has wan static ip to router. enable vpn Cisco server in router. connected with Cisco vpn client. route failed in log. Need to access a PC on the company site with address 192.168.15.105 and router with gateway 192.168.15.1.
How do i configure ip pool ? different ip address? if i connect how do i access pc 192,168.15,105 ? remote pc with 192.168.1.100.
Cisco Routers :: Auto-attendant Or IVR In SRP521W?
May 26, 2012I have a router SRP521W I wonder if you can setup a self-attendant or ivr to this device.
View 4 Replies View RelatedCisco Routers :: SRP521W - Default Route Through VPN?
Mar 18, 2012Is it possible to send all traffic through site to site VPN using SRP521W (on the other site ASA) ? Lets say, traffic to Internet from branch through HQ - site to site VPN between branch and HQ. I've tried to set up destination crypto policy entry to 0.0.0.0 0.0.0.0 but it's not accepted. Firmware version is 1.01.26 (003)
View 4 Replies View RelatedCisco Routers :: SRP521w Ethernet Sub Interfaces On WAN?
Aug 28, 2012Have followed the admin guide, and can setup this up fine, however what we're wanting is to turn off any IP connection for the main wan ethernet interface and only have the sub-interface have an IP connection method.
I can't see how you can turn this off, which is causing a double-up of dhcp requests being sent when using both the main/sub ethernet interfaces to use dhcp.
This has been tested on the 521w and 521w-u versions, and I've just used the latest firmware 1.2.4 on the u version.
How can this be configured so that there is only 1 WAN interface that is using IP (the sub interface) Setting default routes to point to the sub interface doesn't make a difference.
Cisco Routers :: Configuration Template For SRP521W
Nov 3, 2010Any recommendation for creating a configuration template for the SRP521W? I can use the Admin-->Backup Config to get a xxx.cfg file, but I cannot edit it with notepad++. Also, i know the config can be view via view-source: [URL], but how would I load a modified copy of this back to the router?
View 8 Replies View RelatedCisco Routers :: Create VPN Between SRP521W And UC560
Jun 9, 2011I am trying to create a VPN between a SRP521W (only point-to-point VPN) and a UC560 (VPN server) and it seems it doesn't works (SRP doesn't create the tunnel).
View 4 Replies View RelatedCisco Routers :: SRP521W Falling Short
Feb 25, 2013We have been using a SRP521W as the main Router for an office with about 25 users.
So on the cable network it's about 25 computers, 25 IP Phones, 3 printers. Wireless network hold some smartphones and tablets. Computer traffic is 100% Remote Desktop.
That said, for the last few days network connectivity sucks. I think the problem is, precisely, the SRP521W. Some mornings the WAN link is down and can only be brought up by a router reboot.
There's an IPSec tunnel to HQ.
Wireless network was moved recently to a WAP121 to offload the SRP521W. It has two networks: internal and customers with two VLANs.
CPU Usage is around 30-45% all day and spikes to 100% sometimes. RAM Usage is 40-45%. I do not know if this is "too much", "average" or "really low load".
Anyway, time for questions:
a) How can I get a table of active connections on the firewall/NAT to see if there anything "strange" on the network traffic that maybe causing issues?
b) Is there any know bug in the VLAN handling of the SRP that maybe causing the issue? (it's one of the latests changes introduced).
c) If the problem is that there's too much load for such a small router, what replacement would you recommend given the details above? (remember I do not really need wireless on the router as I have the wap121).
Belkin Routers :: N750 - Access Point Support Of Guest Access
Jan 9, 2013Does the N750 (F9K1103V1) support Guest Access while in Access Point mode? It will not provide an IP address when a guest attempts to connect.
View 20 Replies View RelatedBelkin Routers :: F9K1102 V1 Guest Access While In Access Point Mode
Jan 17, 2013I have an n600 ( F9K1102 v1 , firmware 1.00.09 ). My ISP provides my main router for my network, but I want to use the N600 as an access point, I have activated the "Use as Access Point" feature.Is it possible to still utilize the Guest Access feature in this case?
View 1 Replies View RelatedCisco Routers :: SRP521W - Wan Interface Disconnected While 3G Mobile Network Is Connected?
Apr 4, 2012Using a 3G USB Modem (Huwaei E153) the mobile network status is connected however the Wan Interface (AutoConfiguration -DHCP) is displayed as Disconnected (Physical layer disconnected).
View 2 Replies View RelatedCisco Wireless :: 5508WLC Whitelist For Guest Access And Securing Guest-access?
Aug 18, 2011Is it possible to allow certain websites to bypass the web authentication pages, so that they do not need to authenticate to get to our own website, but do have to if they wish to go anywhere else?Looking at a 5508 model at the moment
View 4 Replies View RelatedBelkin Routers :: No Guest Access On N300 F9K1002v1?
Jun 1, 2013I have a N300 f9k1002v1 router and would like to add guest access. Unfortuantely I can't find any info on how to do this. The user guide alludes to it but has no details. I also checked out this link: [URL]
since my router setp does not show "guest access" under "wireless" I skipped to #6 as stated. However when I get to #9 there is no "guest settings" dropdown for me to use.
Cisco Routers :: SRP521W VPN Site-to-Site Tunnel Doesn't Establish
Dec 19, 2011As you can see i have problems with connecting 2 SRP521W together for an VPN tunnel. I tried as much as I can but now i dont know what to do or how and where is the mistake? the connection between these two devices was there last week, after weekend (nothing changed in configs) the connection suddenly was interrupted, without any reason or warning. another day it worked again and 20 mins later connection was dead again...and now it wont establish at all.. here are some screenshots from the vpnconfigs of my devices. one has a static IP the otherone uses FQDN. These are the IKE policies: Here the IPsec Policies: and the GRE policies:
View 10 Replies View RelatedCisco :: Configure WLC To Log Guest Activity To NGS?
Jul 27, 2012We presently have a guest wireless solution in place using 4400/5508 WLC controllers authenticating guests via a NAC Guest server. This has functioned well for the last year or so, but now our security team has requested that we begin logging guest activity. I already have RADIUS accounting set up on the WLAN configuration pointing to the NGS,I have added the NGS to the syslog set up on the controller (I have tried various syslog levels) but I am not receiving any guest activity info in the reports on the NGS. Any way for getting this data?
View 2 Replies View RelatedCisco Routers :: RV120W / Configure Bridge Mode For Internet Access?
Jan 1, 2013We have a RV120W Wireless-N VPN Firewall and we want to configure the router in brigde mode (transparent). Because we have another Firewall, use for filtering and default gateway on the LAN. The ISP provide IP address by DHCP, so we must connect the internet connexion to the WAN interface. But How can we do for connected the RV120W to our firewall? The router mode on the RV120w allows-it to make this configuration?
View 1 Replies View RelatedRouters / Switches :: Configure SpeedTouch Router As Access Point?
Nov 5, 2011i have a LAN network between several pc's connected with several switch's and connected to Thomson SpeedTouch 510 DSL Router its ip address is 10.0.0.100 subnet 255.0.0.0 and the router dont give auto ip to the PCs i have to issign it manually to the PCs "static ip".I bought the acer android recently so i bought a tp-link td-w8901g wireless router to act as an access point so i connected the 2 routers to each other by LAN and gave the tp-link an ip address 10.0.0.12 subnet mask 255.0.0.0 so it will be the same ip range of the speedtouch and setuped the tp-link router to fit my isp configeration it worked at first but i had to reset the router so i did the same configuration i did before but didnt work and i cant access the internet using the android or the wireless but when i connect the phone to the tp-link and unplug the speedtouch the wireless works so theres no any problem with the router?
View 1 Replies View RelatedBelkin Routers :: To Configure N900 To Allow Access To Computer From Outside Network
Feb 12, 2013I need configuring my N900 router to be able to use Microsoft's Remote Desktop Connection to get into my computer from a client's location. I also want to be able to host websites I'm developing so my clients can see the changes before publishing to their website. I have not been able to find anywhere what settings to set to what in order for these two things to be available to me.
View 2 Replies View RelatedCisco Routers :: Configure RV082 Router With Mac Native VPN Client For Remote Access
Oct 9, 2012I am trying to configure RV082 router with Mac Native VPN Client for my remote access. However, no matter what I did, I am not able to make it works. Can any one can give me an example of how to conguration my RV082 router and Mac Book Pro(Mountain Lion)?
View 2 Replies View RelatedHow To Configure Belkin Guest Router
Nov 21, 2012I have belkin n750 router. I cannot get the guest network to connect to internet. The Main one connects to internet. How can I solve this problem?
View 1 Replies View RelatedBelkin Routers :: Configure N300 As Access Point - Unidentified Network?
Nov 9, 2012As per settings menu, I tried to give it an IP address but the new address is not accessible for further configuration. When I connected to the router it status changes to "unidentified network".
My primary network address range is 192.168.1.1 to 192.168.1.10. So I gave address to belkin as 192.168.1.100. But I can not access this address from both primary and belkin network.
Cisco Wireless :: 881w / Configure A Second WLAN For Guest?
Mar 30, 20131 router 881w with a site-to-site VPN connected to a switch and a wireless which allows internal users to access the VPN via wireless (this is like a backup, if the switch fails, then they can use the wireless). Everything's working fine so far. Now I want to configure a second WLAN for guest but I'm not really sure if this configuration will work:
ROUTER:
ip dhcp excluded-address 192.168.100.1 192.168.100.200
!
ip dhcp pool GuestNetwork
network 192.168.100.0 255.255.255.0
default-router 192.168.100.1
dns-server 8.8.8.8
[code]....
If it's not clear I want that everyone that is connected to the guest WIFI receives an IP address from the range I wrote before and then goes directly to the internet.
Cisco Routers :: Configure RV120W So That Internet Users Can Access Internal Company Websites?
Apr 4, 2012How does one configure the router so that Internet users can access internal company websites? The only thing that appears is the Cisco router login. Also I need to configure Terminal Services and its not on the list under Service.
View 2 Replies View RelatedCisco AAA/Identity/Nac :: Configure Guest Vlan And Restricted On 2960
Apr 17, 2011I would like to configure a guest-vlan and restricted-vlan on a 2960 switch, but I can not.
I am trying to configure the interface using the following commands: [code] similar result is obtained while trying to configure a auth-fail vlan. the full configuration file is attached.
Cisco Wireless :: Configure WLC 2106 And LAP 1131AG (light Weight) For Corporate / Guest Wi-Fi
Jan 11, 2012One of my customers asked me to configure a WLC 2106 and 2 LAP 1131AG (lightweight) for corporate/guest Wifi. Basically they want to implement a good wifi connection for internal use and a guest one with different QoS. The two lans should both have dhcp but they must bet kept segregated so that none from the Guest wifi can access corporate resources.
Since i've never configured a WLC from scrath i lightly supposed it would be quite straigh forward as routers and switches from Cisco.Unfortunately i was totally wrong.
I've downloaded the "Cisco Wireless LAN ControllerConfiguration Guide" (Soft.Release 6.0 June 2009) and after i red it i made up this workflow
for the configurations:
1) Configure Controller: (via serial)
- Set Management Interface parameters (IP- SM - Def GW - Dhcp server IP)
- Set Ap-Manager Interface parameters
- Virtual Interface parameters
- Set Admin Credentials
- Dhcp Configuration (internal and/or external)
2) Ap registration on the controller
- Configure vlan with dhcp request redirection to the dhcp server
3) Configure Wlan following customer's requests.
- Configure Wlan Auth for Corporate/Guest Wifi
- Configure QoS for both Wlans
Unfortunately i'm experiencing issue while trying joining the AP to the WLC.It appers that the IT guy of my customer tried to configure one of the Ap.In that Ap's flash i find files referring to a "mesh" configuration like: [code]
Linksys Wireless Router :: EA4200 - Configure WAP54G To Use As Guest Network
Feb 1, 2013The situation is Main house running Linksys EA4200, I have a garage apartment rental that is to far away to receive the wireless guest network.I ran a cat5e to the apartment, can I configure the EA4200 to allow the WAP54G access point to use the guest network? I want to prevent my renters from having access to the home network, but just have basic internet access separate/outside my network.
View 6 Replies View RelatedCisco Wireless :: 2960 - Autonomous Access Point / Get Guest To Access Internet?
May 9, 2012I have two SSIDs on an Autonomous Access Point, that goes to a 2960 switch, that connects to a L3 3560. I have a vlan for admin/private internal access that uses the native vlan (1) and guest vlan (50). I have configured both and I am trying to get both to go out the same Internet connection.
I cannot get the guest access to access the Internet. It looks like my computer will go, but it just comes up saying no Internet access.All interfaces are trunking this vlan properly. I can communicate from the laptop to the 3560 but I just can't get to the Internet.
Linksys Wireless Router :: Configure One Of GigE Ports On E4200 To Only Work On Guest Network
Mar 17, 2012Is there a way to configure one of the GigE ports on the E4200 to only work on the "guest" network? Basically I have a need to setup one of those ports to get to the Internet, but I don't want it to be able to get to anything else on the private side.
View 1 Replies View RelatedCisco WAN :: SRP521W / QoS For 2Mb Connection?
Mar 28, 2011We recently switched from a ADSL2+ service to a 2Mb SHDSL link. Uploading images to our website is happening all day long, thus greater upstream bandwidth was required.
Our downloads are suffering somewhat, the upstream gets easily flooded and downloads start to trickle.
I have a SRP521W which has a few QoS options. The QoS Bandwidth control has upstream bandwidth set to 2048 Kbps. Now I don't know how to enforce anything. How to use the WAN strict high priority queue appriopirately.
The website has a static IP address, so I can target that in the rules to only use 80% of the bandwidth?Alternatively can I limit upstream traffic per user?
