Cisco Routers :: Auto-attendant Or IVR In SRP521W?
May 26, 2012I have a router SRP521W I wonder if you can setup a self-attendant or ivr to this device.
View 4 Replies
ADVERTISEMENT
Cisco Routers :: WAN Port On SRP521W
Mar 14, 2011We've come across an issue whereby the WAN port fails to light up with an Adtran Total Access 832 (via bonded SHDSL) unit.
Eventually the WAN port does light up after connecting and disconnecting it several times with the ethernet cable. However as a test I power cycled the router with the WAN cable disconnected and had a strange issue where the WAN light would constantly flash and show up in the web gui as being connected when in fact the Adtran Unit showed the device was not connected at all.
This is the second Cisco SRP521W router in place as the original one disconnects overnight without any load and a power cycle would fix the issue, but this replacement router disconnects during business hours (even worse for the customer) and power cycling does not bring it back online. We've adjusted the WAN port to 10MB Full on both devices and hope that it stays up. I am wondering if any has had a similar experience? Would this be a behaviour of a faulty unit or may it not be compatible with the Adtran Total Access 832 (via bonded SHDSL) unit perhaps?
Cisco Routers :: SRP521w - Connection With CCA V3.2
May 21, 2012I have a problem in connecting SRP521w with CCA v3.2. I tried to connect the device with CCA but it said that that the device is unsupported. I already upgraded the router's firmware with v1.01.26.
Here is what the CCA looks like every time I try to connect with the router :
Cisco Routers :: SRP521w - VPN Configuration
Jul 2, 2012Cisco srp521w router vpn configuration. company has wan static ip to router. enable vpn Cisco server in router. connected with Cisco vpn client. route failed in log. Need to access a PC on the company site with address 192.168.15.105 and router with gateway 192.168.15.1.
How do i configure ip pool ? different ip address? if i connect how do i access pc 192,168.15,105 ? remote pc with 192.168.1.100.
Cisco Routers :: SRP521W - Default Route Through VPN?
Mar 18, 2012Is it possible to send all traffic through site to site VPN using SRP521W (on the other site ASA) ? Lets say, traffic to Internet from branch through HQ - site to site VPN between branch and HQ. I've tried to set up destination crypto policy entry to 0.0.0.0 0.0.0.0 but it's not accepted. Firmware version is 1.01.26 (003)
View 4 Replies View RelatedCisco Routers :: SRP521w Ethernet Sub Interfaces On WAN?
Aug 28, 2012Have followed the admin guide, and can setup this up fine, however what we're wanting is to turn off any IP connection for the main wan ethernet interface and only have the sub-interface have an IP connection method.
I can't see how you can turn this off, which is causing a double-up of dhcp requests being sent when using both the main/sub ethernet interfaces to use dhcp.
This has been tested on the 521w and 521w-u versions, and I've just used the latest firmware 1.2.4 on the u version.
How can this be configured so that there is only 1 WAN interface that is using IP (the sub interface) Setting default routes to point to the sub interface doesn't make a difference.
Cisco Routers :: Configuration Template For SRP521W
Nov 3, 2010Any recommendation for creating a configuration template for the SRP521W? I can use the Admin-->Backup Config to get a xxx.cfg file, but I cannot edit it with notepad++. Also, i know the config can be view via view-source: [URL], but how would I load a modified copy of this back to the router?
View 8 Replies View RelatedCisco Routers :: Create VPN Between SRP521W And UC560
Jun 9, 2011I am trying to create a VPN between a SRP521W (only point-to-point VPN) and a UC560 (VPN server) and it seems it doesn't works (SRP doesn't create the tunnel).
View 4 Replies View RelatedCisco Routers :: SRP521W Falling Short
Feb 25, 2013We have been using a SRP521W as the main Router for an office with about 25 users.
So on the cable network it's about 25 computers, 25 IP Phones, 3 printers. Wireless network hold some smartphones and tablets. Computer traffic is 100% Remote Desktop.
That said, for the last few days network connectivity sucks. I think the problem is, precisely, the SRP521W. Some mornings the WAN link is down and can only be brought up by a router reboot.
There's an IPSec tunnel to HQ.
Wireless network was moved recently to a WAP121 to offload the SRP521W. It has two networks: internal and customers with two VLANs.
CPU Usage is around 30-45% all day and spikes to 100% sometimes. RAM Usage is 40-45%. I do not know if this is "too much", "average" or "really low load".
Anyway, time for questions:
a) How can I get a table of active connections on the firewall/NAT to see if there anything "strange" on the network traffic that maybe causing issues?
b) Is there any know bug in the VLAN handling of the SRP that maybe causing the issue? (it's one of the latests changes introduced).
c) If the problem is that there's too much load for such a small router, what replacement would you recommend given the details above? (remember I do not really need wireless on the router as I have the wap121).
Cisco Routers :: Configure Wi-Fi Guest Access For SRP521W-K9-G1?
Nov 24, 2012I have one SRP521W-K9-G1 and need to provide guest internet access without access to my network. What is the best way to configure this?
View 3 Replies View RelatedCisco Routers :: Unable To Access SRP521W Web Management
Jan 26, 2013Just brought another set of SRP521W, after changed the WAN setting to PPPOE, we unable to access the web management. The power/sys light will keep blink when trying to access the web management. We able to ping it. We tried the reset button but it did not work as well. Is that a way to upgrade the firmware without using the web management?
View 4 Replies View RelatedCisco Routers :: Cannot Access The Web Management Interface Of SRP521W-U From A Different Subnet
Oct 30, 2012i cannot access the web managemnet interface of this router from a different subnet.THe WAN interface is a 4G LTE connection,I have disabled both the SPI firewall and NAT and enabled remote management from any ip address but i cannot access the admin web page from a remote subnet.Doing a port scan of the routers WAN or LAN address i cannot see any ports open at all...its as if firewall or NAT is still enabled somehow.
View 0 Replies View RelatedCisco Routers :: SRP521W - Wan Interface Disconnected While 3G Mobile Network Is Connected?
Apr 4, 2012Using a 3G USB Modem (Huwaei E153) the mobile network status is connected however the Wan Interface (AutoConfiguration -DHCP) is displayed as Disconnected (Physical layer disconnected).
View 2 Replies View RelatedCisco :: Call Attendant Running In Background
Feb 14, 2013How to run Cisco call attendant running in the background.I have a user (who’s giving me a headache) that wants the Call attendant software to not pop-up when a call come in.She doesnt want to lose her mouse cursor when call comes in.I have looked at the call attendant user guide and not able to find this feature.This user says that the previous Network admin did something to run it in the background.
View 1 Replies View RelatedCisco Routers :: Auto / Programmatic UPnP Port Forwarding For RV042 And E4200 Routers
Jan 24, 2013I have RV042 and E4200 routers . I tried the manual UPnP port forwarding using Rv042 router and was succesful ( by typing 192.168.1.1 in the explorer and logged in using user name and password )
I am using a linux embedded system whose Internal IP ,Internal port are mapped .This system is connected to one of the LAN ports
I want to try auto UPnP port forwarding both for RV042 router and Linksys E4200 routers
After enabling the Upnp option only and logging out ,Can i add a port mapping entry in this router without logging in using a C++ program which runs on linux embedded system .
Cisco Routers :: SRP521W VPN Site-to-Site Tunnel Doesn't Establish
Dec 19, 2011As you can see i have problems with connecting 2 SRP521W together for an VPN tunnel. I tried as much as I can but now i dont know what to do or how and where is the mistake? the connection between these two devices was there last week, after weekend (nothing changed in configs) the connection suddenly was interrupted, without any reason or warning. another day it worked again and 20 mins later connection was dead again...and now it wont establish at all.. here are some screenshots from the vpnconfigs of my devices. one has a static IP the otherone uses FQDN. These are the IKE policies: Here the IPsec Policies: and the GRE policies:
View 10 Replies View RelatedCisco Routers :: Rv220W Does Not Auto-update Dyndns
May 6, 2012I am trying to have the RV220W router auto-update the dyndns registration. The dynamic domain that I use is .info -- note the .info domain.
When I manually update the dyndns information (username and password) the registration does go through and the entry is updated on the dyndns site.
However, the registration does not auto-update after that.
Cisco Routers :: RV220W Auto Refresh Interval
Feb 27, 2013The various setup pages of the RV220W router have an auto-refresh interval. I can change the interval from the default 10 seconds to 60 seconds maximum.I cannot change the Dashboard to different than 10 seconds.Every time I try to work with these pages, they black out and refresh, stopping my work.How do I change the Dashboard auto refresh interval to 60 seconds?Can I change all the auto refresh intervals to 10 minutes?
View 2 Replies View RelatedCisco Routers :: SA500 Not Work And Gets Auto Reboot
May 27, 2013My IPSEC tunnel regulary doesn't work, and the only way is to reboot the SA520.
Is it possible with a batch or something else to auto reboot the SA520 ?
Cisco Routers :: RV220W Auto-reboots Daily?
Oct 12, 2011I recently purchased the RV220W to upgrade by good, but aging RV042. I'm running the most recent firmware (1.0.2.4 as of this writing) and have noticed this router reboots daily. I'm guessing it's locking up and rebooting as it occurs as different times of the day. Compared to the RV042, this was a bit of a pain to setup especially with regard to port forwarding. I'm hesitant to reset and start over again especially since this is brand new.
View 2 Replies View RelatedCisco Routers :: SRP50 Can Router Auto Provision Back To ISP Site
Aug 5, 2012we are busy with a local service provider ( ISP ) and they want to evaluate the SRP500 series and have a few questions that i cant answer clearly.
Can the router auto provision back to the ISP's site , aside from the USB bootup option. i.e manufacture programmed "version "to dial into a specific ISP to provision.
Central administration of SRP500 series: Can the ISP manage and update/ close down SRP500 from a central point. I know the TR069 is std on the SRP500 series, but what does this encompass.
Cisco Routers :: RVS4000 Is Not Renewing DHCP Lease In Auto Mode
Jan 25, 2012my RVS4000 is not renewing DHCP lease in Auto mode. Connection lost after 24 hours.
WAN Internet interface is physically connected to cable modem - Motorola SBV6120E. Setup as DHCP server. Cisco RVS4000 is obtaining DHCP public IP without any issue, the problem is that the connection drop every 24 hours and I need to release/renew DHCP each day to be able to communicate after 24 hours. After I loose connection I need to release DHCP, the WAN interface goes down and I need to renew DHCP then. I receive the same IP address and connection is againg UP and working.
tried to load new firmware and also setup the router with default configuration, but without any change. as there is no auto-reboot function, it is really annoying to log into managment interface each day. I also loose remote access after 24 hours, so I am not able to access the rotuer from outside. My local provider do not support static public IP on WAN, therefore I have to use DHCP.
Belkin Routers :: Play N600 - No Computer Can Auto-connect To It?
Mar 24, 2013Just installed N600 Play router. All computers and phone connect fine, but computers won't auto connect after reboot or sleep. With old router this worked fine.
View 4 Replies View RelatedCisco WAN :: SRP521W / QoS For 2Mb Connection?
Mar 28, 2011We recently switched from a ADSL2+ service to a 2Mb SHDSL link. Uploading images to our website is happening all day long, thus greater upstream bandwidth was required.
Our downloads are suffering somewhat, the upstream gets easily flooded and downloads start to trickle.
I have a SRP521W which has a few QoS options. The QoS Bandwidth control has upstream bandwidth set to 2048 Kbps. Now I don't know how to enforce anything. How to use the WAN strict high priority queue appriopirately.
The website has a static IP address, so I can target that in the rules to only use 80% of the bandwidth?Alternatively can I limit upstream traffic per user?
Cisco WAN :: Auto Failover On The Cat3560?
Sep 20, 2012I have got a Branch Office with two redundant links connecting from Head Office A and Head Office B. Both links are LES 100MB and carry only VLAN 33 traffic. Head Office A has an ASR 1002, Head Office B has Cat3550 and the Branch Office has Cat3560. Both Cat3550 and Cat3560 at L3 switches.At the moment if one link fails i have to manually disable or activate ports/interface on either Head Office A or Head Office B devices and ammend the default gateway on Branch Office switch to either Head Office A or B device, which ever is working.I am looking for an automated and reliable solution for this so that i dont have to make any changes on the devices and failover happens automatically.
View 1 Replies View RelatedCisco :: Auto-negotiation For Ten-giga Ports?
Mar 14, 2013I have already exploited Metro Ethernet, but I don't understand why auto-negotiation does not support for Ten Giga ports?
View 8 Replies View RelatedCisco Switching/Routing :: Auto QoS On 4507R-E?
Mar 15, 2010I have a 4507R-E chassis with Supervisor IV running IOS 12.2(50)SG. I am trying to configure "auto qos voip trust" on some of the uplink ports. When I try to configure it on a port that is in a channel group, I get the error "AutoQoS Error: AutoQoS can not be configured on member port(s) of a port-channel". I have also tried configuring it on the channel interface, but it is not an available command under the channel interface. Is there a way to do auto qos on the channel interfaces or their member ports or does it have to be configured manually?
View 12 Replies View RelatedCisco Switches :: Setting Auto Baud For SG-500-28
Jan 7, 2013I will like to set auto baud for the SG500. By default its 115200bps.
I had tried the following methods:
1) switch xxxxx (config)# line console
switch xxxxx (config-line)# autobaud
--------------------> my terminal hangs and print out rubbish
2) Using http Administrator ->Console setting ( i cannot find the link with console setting)
Cisco WAN :: No Duplex Auto On 7604 Router
Oct 18, 2011I have a 7604 Edge router that connects to our Data centre via Fiber.
but i keep getting input errors on the interface Gi3/5. i also found out that i cannot change the duplex settings on the edge router to auto, i only have two options of full and half and changing it has not worked either.
I have tried to use a switch in between the fiber modem and the edge router to try to manipulate the duplex settings, but when i tried it the port simply shutdown and then i have to reverse the configuration.
The software version of the router is 12.2(33)SRE3, i really need to sort this out as connection to and from the Data centre is quite slow.
Cisco :: LMS 4.0.1 - Device Configuration Auto Backup
Mar 6, 2012Is it possible to create a job what automatically export the devices configs that are in the folder CSCOpxfiles medemushadow? It would be wonderdul if CW could export the .cfg files into a .rar and send in email or something like this.
View 1 Replies View RelatedCisco WAN :: 800 Series Router Auto-sense ATM Pvc
Jan 30, 2012Some of which use snap and some use mux, the router is the one will start the connection and will always be on, untill there is a power cut, if there is. At this point when the power comes back on and a packet's destination is the outside the router should initiate a connection over the atm.
•Do not use this feature on a router that initiates PPPoA sessions.
•This feature supports ATM PVCs. Switched virtual circuits (SVCs) are not supported.
•PPPoA does not support static IP assignments within virtual templates.
The second and thrid I can understand and the 3rd will just get assigned an IP address from the ISP.But with the first point how is it possible to set this up when the router cannot initate the connection?
Cisco :: How To ASR 9k Auto-backup To External FTP Server
Jun 20, 2012How to take auto running configuration backup when use commit command in asr9k .Our asr9k sofware Version 4.0.1[Default] .I usse the commands
ftp client password encrypted 050D121F345F4B1B4
ftp client username cisco
ftp client source-interface GigabitEthernet0/0/0/14
ftp client anonymous-password cisco
(Password information changed)
configuration commit auto-save filename ftp://10.10.10.3/ASR9K/asr_conf But auto backup not happening .following errror showing after every COMMIT command.
( Error:Couldn't save file /ftp://10.10.10.3/ASR9k/asr_conf.
Error:'CfgMgr' detected the 'warning' condition 'Operation is temporarily suspended.' )
Manually I able to take Running-configuration backup through ftp int same lacation (ftp://10.10.10.3/ASR9K/asr_conf ) .But automatically not happening .
Cisco :: WLC 5508 Auto-reboot After Time X
Dec 13, 2011we have the issue that a new WLC 5508 has been installed in a new location. Unfortunaltelly we have no hands-on suopport on-site, so just remote connection.Now we figured that the service-port and management interfaces have to be reconfigured. In case we can not reach the WLC with the new configured interfaces it would be useful if the WLC reboots automatically after time x to reload the previouse working configuration.So the question is, is there a functionality to create a script which reboots the WLC automatically after time x?
View 4 Replies View Related