The various setup pages of the RV220W router have an auto-refresh interval. I can change the interval from the default 10 seconds to 60 seconds maximum.I cannot change the Dashboard to different than 10 seconds.Every time I try to work with these pages, they black out and refresh, stopping my work.How do I change the Dashboard auto refresh interval to 60 seconds?Can I change all the auto refresh intervals to 10 minutes?
View 2 RepliesI am trying to have the RV220W router auto-update the dyndns registration. The dynamic domain that I use is .info -- note the .info domain.
When I manually update the dyndns information (username and password) the registration does go through and the entry is updated on the dyndns site.
However, the registration does not auto-update after that.
I recently purchased the RV220W to upgrade by good, but aging RV042. I'm running the most recent firmware (1.0.2.4 as of this writing) and have noticed this router reboots daily. I'm guessing it's locking up and rebooting as it occurs as different times of the day. Compared to the RV042, this was a bit of a pain to setup especially with regard to port forwarding. I'm hesitant to reset and start over again especially since this is brand new.
View 2 Replies View Relatedmy DSL light is blinking at evening around 6:30 evening every day.
View 1 Replies View RelatedI have RV042 and E4200 routers . I tried the manual UPnP port forwarding using Rv042 router and was succesful ( by typing 192.168.1.1 in the explorer and logged in using user name and password )
I am using a linux embedded system whose Internal IP ,Internal port are mapped .This system is connected to one of the LAN ports
I want to try auto UPnP port forwarding both for RV042 router and Linksys E4200 routers
After enabling the Upnp option only and logging out ,Can i add a port mapping entry in this router without logging in using a C++ program which runs on linux embedded system .
I have a router SRP521W I wonder if you can setup a self-attendant or ivr to this device.
View 4 Replies View RelatedMy IPSEC tunnel regulary doesn't work, and the only way is to reboot the SA520.
Is it possible with a batch or something else to auto reboot the SA520 ?
after a certain period of time (ranging from 2 minutes to several hours) the unit keeps dropping the WAN connection, making the unit unaccessible from the WAN side. The strange thing is, that when the connection is dropped, the unit is perfectly accessible from the LAN side, the WAN LED is still on, status info shows the WAN link up, and packet trace shows broadcasted traffic on the WAN interface, so only the directed communication to and from the ISPs gateway (configured to fix IP) seems to be blocked for some reason. When this happens, then plugging the WAN cable to the Optional WAN port enables traffic again, but it is also dropped after some time, and then only power cycling the unit restores WAN connectivity.
View 0 Replies View RelatedI have a cisco 7600. It will send an icmp request every second. If the icmp response is not received, 3 consecutive icmp requests will be sent. SLA reachability down will be reported after all 4 icmp responses are not received. The following diagram illustrates my goal.
Sender --------------------------------------- 0 second -> 0 sec (1st icmp Request is sent out)-> 50ms (no response, send 2nd icmp after timeout)-> 50ms (no response, send 3rd icmp after timeout) -> 50ms (no response, send 4th icmp after timeout) 50ms Report SLA reachability down
--------------------------------------- 1 second
--------------------------------------- 2 second
Question: will the following configuration achieve my goal?
ip sla 100icmp-echo 10.32.24.1 source-ip 10.32.24.2timeout 50frequency 1
ip sla monitor reaction-configuration 100 react timeout threshold-type consecutive 3 action-type triggerOnly
I have 802.1x configured on a 3550 switch with ACS 5.1 acting as the AAA policy server.
My problem is this. When my computer boots up, ACS authenticates the machine to AD slapping me in a guest VLAN with limited access to the network. Once I login though, I reauthenticate to AD via ACS which then puts me into an employee VLAN but my IP address doesn't refresh automatically. I have to run ipconfig /renew to get my IP in the correct VLAN or write a logon script that does the same thing everytime I log in.
Is there anyway for this to be done automatically outside of writing a logon script?
we are busy with a local service provider ( ISP ) and they want to evaluate the SRP500 series and have a few questions that i cant answer clearly.
Can the router auto provision back to the ISP's site , aside from the USB bootup option. i.e manufacture programmed "version "to dial into a specific ISP to provision.
Central administration of SRP500 series: Can the ISP manage and update/ close down SRP500 from a central point. I know the TR069 is std on the SRP500 series, but what does this encompass.
my RVS4000 is not renewing DHCP lease in Auto mode. Connection lost after 24 hours.
WAN Internet interface is physically connected to cable modem - Motorola SBV6120E. Setup as DHCP server. Cisco RVS4000 is obtaining DHCP public IP without any issue, the problem is that the connection drop every 24 hours and I need to release/renew DHCP each day to be able to communicate after 24 hours. After I loose connection I need to release DHCP, the WAN interface goes down and I need to renew DHCP then. I receive the same IP address and connection is againg UP and working.
tried to load new firmware and also setup the router with default configuration, but without any change. as there is no auto-reboot function, it is really annoying to log into managment interface each day. I also loose remote access after 24 hours, so I am not able to access the rotuer from outside. My local provider do not support static public IP on WAN, therefore I have to use DHCP.
After some time LMS stops to refresh network topology (not changing colors for devices which lost/found). However, if I restart topology services devices are refreshed.
Checked the processes. Everything is fine but there is a process named "1018". But I did not found any job with this number.
Just installed N600 Play router. All computers and phone connect fine, but computers won't auto connect after reboot or sleep. With old router this worked fine.
View 4 Replies View RelatedI have CiscoWorks 3.1.
1. When creating job or log file, these files are always stored in the default Path (inside LMSROOT) for RME for example...Could I change RME default Path to store these files in another location inside the Hard Disk?
2. Could I Configure CW-LMS to send all the reports to me by mail?
3. What is the Difference between Poll Interval time and Collection time inside RME?
I am working on a wlc 5508 in a lab environment doing snmp reporting & i was wondering if there is anyway to after the timing on how quick the snmp traps appear on the trap log page? I have looked through the gui but cant seem to find anything, so not too sure if there is a cli command, the traps come in very quickly on the nms way before they appear on the trap log page.
View 1 Replies View RelatedI've been having a problem with my wireless network connection. Whenever I try and hit the Repair function,it will get stuck on Renewing your IP address for a moment, then change to: Windows could not finishing repairing the problem because the following action cannot be completed: Connecting to the wireless network. I have internet connection on this same computer.Another point to make is that when I click Repair and navigate to the Network Connections window, then hit F5 ( refresh the window ), the wireless connection will quickly refresh and connect normally without error.I won't have to open the Network Connections page and hit F5 anytime I need to repair the connection? Also, as of right now, it's still "Acquiring network address" even though I'm connecting and typing this message.
View 10 Replies View RelatedI have a customer that have trouble with the update of the position of a client. Even if the clients walks across the whole building, the client will stay at the same place for several minutes. Is there any way to tune the refresh rate? When I push the load button in the map, the clients position will refresh, or it did when I was on the site, now they just test with an application.
The setup:
WiSM 7.0.220
WCS 7.0.220
MSE 7.0.220
They use the API for MSE to get the location information to the external application, and that will show the information on a cisco 7925 IP phone.know a way to increasing the refresh rate?
when using SNMP on our cisco 3845 the traffic logs are set to refresh every 1 second but the data seems to come in 5 sec burst.so does not some a real time status of the interface throughput.
View 2 Replies View RelatedRegion : Others
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP :
My router is not working and only all lights are flashing everytime after interval of 2 seconds.
what exactly is QuickVPN?Is it a IPSec VPN?Is it a PPTP?Is it a SSLVPN?can I resolve my local hostnames? That means, can I configure a lokal DNS Server?
View 3 Replies View RelatedI am trying to setup and configure a VPN on the RV220W that uses IPSEC so I can use the Cisco VPN Client I use at work, I have gone through the user manual 11 or 12 times now but still cannot work it out. I cannot find where on the Rv200W iset up the phase 1 authentication username and password which will then lead me onto the phase 2 stage of asking for a username password to allow me access.
View 8 Replies View RelatedPicked up a pair of RV220W's for a project I'm working on. I have several IP's available, 4 of which are assigned to/in use by a server behind the RV220W. All 4 of these IP's are static external IPs. How I can configure the RV220W so that requests to those 4 IP's get routed to the server.
Prior to purchasing this, I was under the impression what I was trying to do was called one-to-one NAT, but after reading the 'Help' document on the one-to-one NAT page, I don't think this is right. Emphasis added below: Cisco RV220W Wireless-N Network Security Firewall Help FirewallOne-to-One NATOne-to-one NAT is a way to make systems behind a firewall and configured with private IP addresses appear to have public IP addresses.One-to-One-NAT Rule TableThis table lists the list of available One-To-One NAT rules configured by the user. Private Range Begin: start ip address in private (LAN) ip addressPublic Range Begin: start ip address in the public ip address (WAN IP), Public IP Subnet Mask: The Subnet Mask of the public IPRange Length: Range length maps one to one private address to public address up to the given range.Service: This column shows service to be accepted by LAN Host.The actions that can be taken on One-to-One-NAT rules are:(Check Box At First Column Header): Selects all the entries in the table.Add: Opens the One-To-One NAT Configuration page, to add a new entry. Edit: Opens the One-To-One NAT Configuration page, to edit the selected entry.Delete: Deletes the selected entries.
So according to their documentation, the server in question would need to be configured with a private IP. Unfortunately, one of the applications I use is licensed via IP address and my understanding is that I cannot use the software with private/non-routable IP addresses.
Is the RV220W capable of not only securing the line (firewall, access rules, content filtering, port trigering & forwarding etc) but also doing what I was hoping to do (keeping the external IP's on the server, and routing appropriately)?
I'm using a RV220W router, and recently got shifted to a dynamic IP solution.Now, I've got a no-ip.org address, but the update service seems to be on no-ip.com. So, I try to enter mydomain.no-ip.org OR mydomain.no-ip.com in the dynamic dns settings, under Host and Domain Name, but when saving the settings it says
'The hostname specified does not exist in this user account' ,which seems to indicate that it manages to login to the update service but gets a negative reply.Is it possible to use the RV220W with no-ip.org/com?
We have 2 sites connected thru 2 RV220W routers via VPN and most things are working fine. I have noticed however, that any device that has a web interface, i.e. our Sharp Copier and our Freenas server, is inaccessible. The page tries to come up but then I get the Cisco "server is down" page generated by the RV220W.
I can pull up the web interface pages if I use a machine on the local LAN but not on any machine across the VPN. The only commonality I can think of is the RV220W blocking that traffic for some reason..
Cisco support write down manual (workaround), how to setup IPsec VPN connection on Mac OS 1.7?
View 5 Replies View RelatedIs there anyway to associate a name to an IP in the RV220W? I am coming from a WRVS4400N v2. Folks are complaining that they can't connect, for example via Real VNC, via the PC name any longer. They have to use the IP address. In the past I put the names of the PCs in the WRVS4400N when I reserved IPs via MAC addresses (some call this assigning static IPs). There isn't any place in the RV220W to put the name. Even when I look at the DHCP list a lot of them show up as "unknown". I am sure this is a NETBIOS thing but I'd rather fix this in the router as I have always done in the past.
View 4 Replies View Relatedi have a RV220W and absolutely nothings functional on this stupid Router, no NAT , no Port Forwarding and I cant access my Network from Outside. Any firmware link for downloading. This address works, its handling special webrequest.
View 1 Replies View RelatedI set up a PPTP VPN with an RV220W recently. It was working flawlessly until a recent power outage and now users are getting the 807 error when attempting to connect. I have PPTP passthrough enabled and TCP/UDP 1723 open. As far as I can tell GRE 47 is open as well. Why it was working and is not working after a power outage?
View 2 Replies View RelatedHaving a strange problem that just started this week and got worse this evening. I have a RV220W that is feeding my network. The RV220W sits behind a broadband modem and acts as the DHCP for the network and those computers access the internet that way. Anyway, tonight started an issue where the the RV220W just disappears. Becomes unpingable. I recycle power, and within anywhere from 5 to 10 minutes, it's gone. No longer pingable. Even if I plug a latop directly into it.If I power cycle the RV220W it comes back and I can ping it and access it and its settings. 5 to 10 mins later, I again lose it. Nothing was done. Its been working fine for a few weeks. Had a similar outage last Tuesday, but a recycle of everything brought everything back into line. After I lose connection to it, the lights I expect to be lit remain lit.
View 1 Replies View RelatedI just got an EA3500 and I guess I don't understand what "Refresh" does when viewing the DHCP client table under the "Status", "Local Network" tab of the web interface, either that or it's not working. If I have active wired and wireless clients and I power off the EA3500, wait a few minutes, then power it back on, the table is blank. If I hit "Refresh" I would expect it to re-populate the table with the connected clients. For whatever reason, it doesn't. I have to physically disconnect and reconnect the E-net cable, or power cycle the wireless client to get them to reappear in the table. Is something wrong with the router or its s/w
View 9 Replies View RelatedI am unable to make UPnP to work on the RV220W. I am forced to use port forwarding.
View 10 Replies View RelatedNothing happens when clicking the SAVE button after making changes on the VLAN Membership screen when using IE9, but it work fine with IE8. Any problems using IE9 during configuration?
View 4 Replies View Related