Cisco Routers :: Configuration Template For SRP521W
Nov 3, 2010
Any recommendation for creating a configuration template for the SRP521W? I can use the Admin-->Backup Config to get a xxx.cfg file, but I cannot edit it with notepad++. Also, i know the config can be view via view-source: [URL], but how would I load a modified copy of this back to the router?
View 8 Replies
ADVERTISEMENT
Jul 2, 2012
Cisco srp521w router vpn configuration. company has wan static ip to router. enable vpn Cisco server in router. connected with Cisco vpn client. route failed in log. Need to access a PC on the company site with address 192.168.15.105 and router with gateway 192.168.15.1.
How do i configure ip pool ? different ip address? if i connect how do i access pc 192,168.15,105 ? remote pc with 192.168.1.100.
View 2 Replies
View Related
Sep 13, 2012
I am working up a configuration template for an install I am doing in a couple weeks and wanted to take a look at the base config of an ASR1002.
View 1 Replies
View Related
Jan 3, 2013
What is the VPC configuration template with two core 6509 switch.Pls find the attachment for Network topology.
View 3 Replies
View Related
Apr 6, 2013
Who can give me a SNMPv3 configuration template.I tried many times has been a problem
View 5 Replies
View Related
Nov 30, 2011
is it possible to create some Configuration Template that pushes configurations only to switches or interfaces with a certain actual existing configuration element- e.g. a certain interface description?
Example:Template Parameter Mask asks User for an Interface Description- the User enters e.g. "A101" Second Parameter asks User for an access vlan to deploy to this interfaces- e.g. " 10"
So during deployment LMS make a "switchport access vlan 10" only on interfaces that contain the description "A101".
I know this is possible via Compliance Check/Deploy, but we want to make this more User friendly and flexible so that e.g. a Helpdesk Member can use this Template to easily change the VLAN based on a interface description (which refers in this case to a CAT5 outlet label).
View 1 Replies
View Related
Mar 14, 2011
We've come across an issue whereby the WAN port fails to light up with an Adtran Total Access 832 (via bonded SHDSL) unit.
Eventually the WAN port does light up after connecting and disconnecting it several times with the ethernet cable. However as a test I power cycled the router with the WAN cable disconnected and had a strange issue where the WAN light would constantly flash and show up in the web gui as being connected when in fact the Adtran Unit showed the device was not connected at all.
This is the second Cisco SRP521W router in place as the original one disconnects overnight without any load and a power cycle would fix the issue, but this replacement router disconnects during business hours (even worse for the customer) and power cycling does not bring it back online. We've adjusted the WAN port to 10MB Full on both devices and hope that it stays up. I am wondering if any has had a similar experience? Would this be a behaviour of a faulty unit or may it not be compatible with the Adtran Total Access 832 (via bonded SHDSL) unit perhaps?
View 1 Replies
View Related
May 21, 2012
I have a problem in connecting SRP521w with CCA v3.2. I tried to connect the device with CCA but it said that that the device is unsupported. I already upgraded the router's firmware with v1.01.26.
Here is what the CCA looks like every time I try to connect with the router :
View 1 Replies
View Related
Aug 17, 2011
We have created a sample configuration for ISRG2 2901 Router. The sample configuration is long, and with copy/paste it is possible to skip some lines, and it is difficult to ensure the configuration of every device is standardized due to this error possibility. What we are trying to achieve is first create a template from this sample configuration file, and then create configuration files for each device seperately and automatically. After creating this configuration instances, we want to be able to distribute the configuration files (and possibly the ios) to the devices during the staging phase. Since there are about 1000 2901 routers, creating configuration files is important?
From searching we have found the following tools:
1) CCE (Cisco Configuration Engine): This tool seems to be very efficient for distributing the created configuration files. We may use the serial number of the device, and it provides almost zero touch provisioning of the configuration files to the devices. Creating the configuration file from the template seems to be manual, i.e enter the ip addresses of the interfaces, the routing tables one by one for each device. How can we use velocity template for device configs?
2) Ciscoworks LMS Prime: It is possible to create a baseline template for the devices, and after getting the backup configuration of the routers, it is possible to compare the actual configuration of the device with the baseline template, and understand if there is any difference with each other. This is indeed very useful in order to keep the configuration standardized, we again could not find a way to create bulk configuration files from the baseline template.
3) Solarwinds Config Generator: This tool is useful for creating a configuration file from a template, but again not for automatically creating configuration files, and needs manual intervention.
4) Excel Macro: It seems that some people have achived to automatically create configuration files with using an excel macro, but we could not find a procedure or tip of how to achieving this.
5) Pearl or TCL/TK Script: Again since we are not software developers but from networking field, it is difficult to achieve a working form of this scripts or codes due to to lack of documentation and development experience.
View 1 Replies
View Related
May 26, 2012
I have a router SRP521W I wonder if you can setup a self-attendant or ivr to this device.
View 4 Replies
View Related
Mar 18, 2012
Is it possible to send all traffic through site to site VPN using SRP521W (on the other site ASA) ? Lets say, traffic to Internet from branch through HQ - site to site VPN between branch and HQ. I've tried to set up destination crypto policy entry to 0.0.0.0 0.0.0.0 but it's not accepted. Firmware version is 1.01.26 (003)
View 4 Replies
View Related
Aug 28, 2012
Have followed the admin guide, and can setup this up fine, however what we're wanting is to turn off any IP connection for the main wan ethernet interface and only have the sub-interface have an IP connection method.
I can't see how you can turn this off, which is causing a double-up of dhcp requests being sent when using both the main/sub ethernet interfaces to use dhcp.
This has been tested on the 521w and 521w-u versions, and I've just used the latest firmware 1.2.4 on the u version.
How can this be configured so that there is only 1 WAN interface that is using IP (the sub interface) Setting default routes to point to the sub interface doesn't make a difference.
View 3 Replies
View Related
Jun 9, 2011
I am trying to create a VPN between a SRP521W (only point-to-point VPN) and a UC560 (VPN server) and it seems it doesn't works (SRP doesn't create the tunnel).
View 4 Replies
View Related
Feb 25, 2013
We have been using a SRP521W as the main Router for an office with about 25 users.
So on the cable network it's about 25 computers, 25 IP Phones, 3 printers. Wireless network hold some smartphones and tablets. Computer traffic is 100% Remote Desktop.
That said, for the last few days network connectivity sucks. I think the problem is, precisely, the SRP521W. Some mornings the WAN link is down and can only be brought up by a router reboot.
There's an IPSec tunnel to HQ.
Wireless network was moved recently to a WAP121 to offload the SRP521W. It has two networks: internal and customers with two VLANs.
CPU Usage is around 30-45% all day and spikes to 100% sometimes. RAM Usage is 40-45%. I do not know if this is "too much", "average" or "really low load".
Anyway, time for questions:
a) How can I get a table of active connections on the firewall/NAT to see if there anything "strange" on the network traffic that maybe causing issues?
b) Is there any know bug in the VLAN handling of the SRP that maybe causing the issue? (it's one of the latests changes introduced).
c) If the problem is that there's too much load for such a small router, what replacement would you recommend given the details above? (remember I do not really need wireless on the router as I have the wap121).
View 3 Replies
View Related
Nov 24, 2012
I have one SRP521W-K9-G1 and need to provide guest internet access without access to my network. What is the best way to configure this?
View 3 Replies
View Related
Jan 26, 2013
Just brought another set of SRP521W, after changed the WAN setting to PPPOE, we unable to access the web management. The power/sys light will keep blink when trying to access the web management. We able to ping it. We tried the reset button but it did not work as well. Is that a way to upgrade the firmware without using the web management?
View 4 Replies
View Related
Oct 30, 2012
i cannot access the web managemnet interface of this router from a different subnet.THe WAN interface is a 4G LTE connection,I have disabled both the SPI firewall and NAT and enabled remote management from any ip address but i cannot access the admin web page from a remote subnet.Doing a port scan of the routers WAN or LAN address i cannot see any ports open at all...its as if firewall or NAT is still enabled somehow.
View 0 Replies
View Related
Apr 4, 2012
Using a 3G USB Modem (Huwaei E153) the mobile network status is connected however the Wan Interface (AutoConfiguration -DHCP) is displayed as Disconnected (Physical layer disconnected).
View 2 Replies
View Related
Dec 19, 2011
As you can see i have problems with connecting 2 SRP521W together for an VPN tunnel. I tried as much as I can but now i dont know what to do or how and where is the mistake? the connection between these two devices was there last week, after weekend (nothing changed in configs) the connection suddenly was interrupted, without any reason or warning. another day it worked again and 20 mins later connection was dead again...and now it wont establish at all.. here are some screenshots from the vpnconfigs of my devices. one has a static IP the otherone uses FQDN. These are the IKE policies: Here the IPsec Policies: and the GRE policies:
View 10 Replies
View Related
Mar 28, 2011
We recently switched from a ADSL2+ service to a 2Mb SHDSL link. Uploading images to our website is happening all day long, thus greater upstream bandwidth was required.
Our downloads are suffering somewhat, the upstream gets easily flooded and downloads start to trickle.
I have a SRP521W which has a few QoS options. The QoS Bandwidth control has upstream bandwidth set to 2048 Kbps. Now I don't know how to enforce anything. How to use the WAN strict high priority queue appriopirately.
The website has a static IP address, so I can target that in the rules to only use 80% of the bandwidth?Alternatively can I limit upstream traffic per user?
View 2 Replies
View Related
Feb 3, 2013
Using LMS 3.2, I've started learning how to use the compliance templates.is there a regex to ignore case? For instance, if I have the line:
clock timezone est -5 in some configs, and
clock timezone EST -5 in others
is there a way to tell the template that upper case and lower case are acceptable matches?
View 1 Replies
View Related
Nov 2, 2011
I want to add the command "no logging event link-status" to all switchport mode access ports EXCEPT for the ones with the following switchport access vlans: 4022,4032,4042,4052,4072 & 4082. How do I create a compliance template to do this? LMS 3.2, RME 4.3.1
View 6 Replies
View Related
Jun 24, 2010
Have upgraded WCS to 7.0 due to a Mesh network feature we needed, but now see I can no longer edit the AP migration templates. The interface allows me to create or delete them but the command dropdown box does not show an Edit option. So now for every AP I want to migrate I need to create a new template before I can select the AP's and migrate them. I still need to migrate about 220 APs....
Looking though the function it tells me to click on the Migration Template name. However neither in MS IE nor Firefox this works, there is no link activated.
View 7 Replies
View Related
Jun 5, 2013
I am trying to create a very basic template in compliance manager that checks for interfaces that aren't members of specific VLANs. VLAN 10 being one of them. I want to match interfaces assigned to VLAN 20. According to the documentation I have read, the following range statement should work because 10 falls between 3 and 19:
Submode: interface [#.*Ethernet.*#]
- switchport access vlan [#[3-19]#]
With the preceeding statement, however, interfaces assigned to both VLAN 10 and VLAN 20 are matching the rule. With this specific rule (not a range), only interfaces w/VLAN 20 are processed by the template, which is expected. We actually have numerous VLANs that we want to exclude/include. I only mentioned VLANs 10 and 20 for brevity.
View 1 Replies
View Related
Nov 26, 2011
Me and some friends of mine talking about making a small website for us to share our photos together and be able to add comments under each photo, for example or even better with a simple forum. I have a bit experience making website, but we prefer to use web templates / packages for that also we would be able to add comments( built-in Code, no external links for those codes be needed). We prefer to have our website sure we know there are thousands of free photo-sharing websites out there.
View 2 Replies
View Related
Oct 20, 2011
Asking about Packet Tracer. I currently use packet tracer 5.3.2.Can you give me any link where to download router template on packet tracer? I want to explore cisco 2821 but packet tracer 5.3.2 has an existing of cisco 2811 only then, I tried to add the 4 ports of RJ11 but I cannot see the 4 port telphone.
View 4 Replies
View Related
Aug 1, 2012
I get that to avoid fragmenting the packets we need to reduce the MTU to 1492, fine, but should the MTU restriction be applied at the virtual-template (server)/dialer (client) or on the physical ethernet interfaces?If I apply it to one or the other, which takes precedence? Should I just apply it to both the virtual/dialer interfaces and the ethernet interfaces?
View 6 Replies
View Related
Aug 8, 2012
I am trying to apply WLAN template from NCS to two WLCs 5508 and I receive this message."Another WLAN with same SSID and either WPA1/ WPA2/ WPA1+WPA2 is enabled. Please change the Layer 2 security policy."The template has layer 2 security with WPA+WPA2 enable and 802.1x.I have other WLAN template with other name and other SSID with the same security policies with no problem to apply.
View 2 Replies
View Related
Oct 13, 2011
LMS 3.2.1, what is the correct baseline template syntax to accomplish the requirement 2:
Requirement 1
• Check if the router is running H323: You can do it looking for the command “h323-gateway voip interface”. If that command is found on a router then it is an H323 voice gateway
• Configure the global command: voice class h323 1
[Code]...
View 1 Replies
View Related
May 3, 2012
The business i work for uses a "Do it myself" template for their website. (this is through their webhosting company). I can not add FTP to this website, we have to completely redo it with code and whatnot in order to have access to FTP. We would like users to download a template from our website (no problem) and then send us their artwork files back to us. These can be upwards of 150mb. Is there another option that i am not aware of to do this? Can't use email, has a limit of 25mb.
View 6 Replies
View Related
Feb 4, 2013
According to cisco manual in order to change SDM template i need to reboot switch, but when i have C3750-X stack do i need to reboot stack or maybe will be enough reboot in sequence the stack members?
View 3 Replies
View Related
Jun 11, 2013
I attempted to assign a User Roles template to a## 2504 controller and if failed with message stating controller version not supported. My current WCS version is 7.0172, if I upgrade to the lastest version will that resolve the template issue?
View 4 Replies
View Related
Sep 21, 2011
Network Resources - Network Devices and AAA Clients- File Operations - Add - gives me File Format Validation Faliled. I am carefull to leave the header as it is. The header in the Import Template looks faulty, see attached. When exporting devices I also get the same header as attached. I also tried to change the header so its all in one column, but with same result.
View 1 Replies
View Related