Cisco :: WCS 7.0 Cannot Edit AP Migration Template
Jun 24, 2010
Have upgraded WCS to 7.0 due to a Mesh network feature we needed, but now see I can no longer edit the AP migration templates. The interface allows me to create or delete them but the command dropdown box does not show an Edit option. So now for every AP I want to migrate I need to create a new template before I can select the AP's and migrate them. I still need to migrate about 220 APs....
Looking though the function it tells me to click on the Migration Template name. However neither in MS IE nor Firefox this works, there is no link activated.
View 7 Replies
ADVERTISEMENT
Jul 15, 2012
In previous versions of LMS, I navigated to RME - Devices - Inline Edit to increase the snmp timeout. I haven't been able to locate the same process in LMS 4.2. Where I can locate this feature?
View 1 Replies
View Related
Feb 3, 2013
Using LMS 3.2, I've started learning how to use the compliance templates.is there a regex to ignore case? For instance, if I have the line:
clock timezone est -5 in some configs, and
clock timezone EST -5 in others
is there a way to tell the template that upper case and lower case are acceptable matches?
View 1 Replies
View Related
Dec 9, 2012
We are deploying over 20 RV180W Routers for a client and need to find a faster way to configure them for shipping.We have created a base image (all settings that will be shared between the 20 locations), we need an easy and quick way to make IP changes for the 3 VLANs and Local Security Groups for the IPSEC VPN.I tried to edit the CFG file by hand, but the checksum fails when it is loaded into the RV180W.How can I accomplish this? Can I manually create the checksum?Can I remove the checksum?
View 3 Replies
View Related
Nov 2, 2011
I want to add the command "no logging event link-status" to all switchport mode access ports EXCEPT for the ones with the following switchport access vlans: 4022,4032,4042,4052,4072 & 4082. How do I create a compliance template to do this? LMS 3.2, RME 4.3.1
View 6 Replies
View Related
Oct 3, 2012
Been a while since I have conf'd a controller. I believe its WLAN/edit/security/layer2 and below psk format edit the password?
View 2 Replies
View Related
May 15, 2013
I am very new to configuring ports on a switch. My boss usually does the port configurations but I am starting to learn some of the basic commands. The commands I know how to do are; close a port by typing config t, int gi0/port# and typing shut. I know how to enable a port, but how can I add info to a port or copy settings from one port to another?
We have some ports that are configured for 192.168 addresses but most are 10.128 addresses. I need to configure a certain port to be able to receive 192.168 addresses.
View 2 Replies
View Related
Mar 7, 2012
I have to add some new ACEs on a Critical production 6500 running CatOS.The documentation that I have seen so far explains how to create, commit and vlan map a VACL ... however I see no instructions or comments on best practices for editing VACLs.
View 1 Replies
View Related
Sep 13, 2012
I am working up a configuration template for an install I am doing in a couple weeks and wanted to take a look at the base config of an ASR1002.
View 1 Replies
View Related
Jun 5, 2013
I am trying to create a very basic template in compliance manager that checks for interfaces that aren't members of specific VLANs. VLAN 10 being one of them. I want to match interfaces assigned to VLAN 20. According to the documentation I have read, the following range statement should work because 10 falls between 3 and 19:
Submode: interface [#.*Ethernet.*#]
- switchport access vlan [#[3-19]#]
With the preceeding statement, however, interfaces assigned to both VLAN 10 and VLAN 20 are matching the rule. With this specific rule (not a range), only interfaces w/VLAN 20 are processed by the template, which is expected. We actually have numerous VLANs that we want to exclude/include. I only mentioned VLANs 10 and 20 for brevity.
View 1 Replies
View Related
Nov 3, 2010
Any recommendation for creating a configuration template for the SRP521W? I can use the Admin-->Backup Config to get a xxx.cfg file, but I cannot edit it with notepad++. Also, i know the config can be view via view-source: [URL], but how would I load a modified copy of this back to the router?
View 8 Replies
View Related
Nov 26, 2011
Me and some friends of mine talking about making a small website for us to share our photos together and be able to add comments under each photo, for example or even better with a simple forum. I have a bit experience making website, but we prefer to use web templates / packages for that also we would be able to add comments( built-in Code, no external links for those codes be needed). We prefer to have our website sure we know there are thousands of free photo-sharing websites out there.
View 2 Replies
View Related
Jan 11, 2012
I am new user of cisco router i can access the hardware and login in the account but the problem is if i use the command "enable" asking for a password, old I.T. personnel who setup this router already resign.
View 2 Replies
View Related
Jan 10, 2013
I have a switch where the current power threshold is set to -20.0db. The problem is that the receive power fluctuates between -19.9db to -20.1db, which is causing it to throw alarms on my solarwinds monitoring server. What I would like to do is change it to a different warning threshold, but I can't seem to find the command to do so. This is a catalyst 3750 running IOS version 12.2(55)SE3. [code]
View 5 Replies
View Related
Apr 13, 2011
Is it possible to edit the hosts file on an ACS 1121 server running ACS 5.2? Our problem is we have a single domain with multiple domain controllers at different sites. So when the ACS server tries connecting to the domain it randomly picks a domain controller which it can't connect to thus causing it to fail.
View 5 Replies
View Related
Oct 20, 2011
Asking about Packet Tracer. I currently use packet tracer 5.3.2.Can you give me any link where to download router template on packet tracer? I want to explore cisco 2821 but packet tracer 5.3.2 has an existing of cisco 2811 only then, I tried to add the 4 ports of RJ11 but I cannot see the 4 port telphone.
View 4 Replies
View Related
Aug 1, 2012
I get that to avoid fragmenting the packets we need to reduce the MTU to 1492, fine, but should the MTU restriction be applied at the virtual-template (server)/dialer (client) or on the physical ethernet interfaces?If I apply it to one or the other, which takes precedence? Should I just apply it to both the virtual/dialer interfaces and the ethernet interfaces?
View 6 Replies
View Related
Aug 8, 2012
I am trying to apply WLAN template from NCS to two WLCs 5508 and I receive this message."Another WLAN with same SSID and either WPA1/ WPA2/ WPA1+WPA2 is enabled. Please change the Layer 2 security policy."The template has layer 2 security with WPA+WPA2 enable and 802.1x.I have other WLAN template with other name and other SSID with the same security policies with no problem to apply.
View 2 Replies
View Related
Jan 3, 2013
What is the VPC configuration template with two core 6509 switch.Pls find the attachment for Network topology.
View 3 Replies
View Related
Apr 6, 2013
Who can give me a SNMPv3 configuration template.I tried many times has been a problem
View 5 Replies
View Related
Oct 13, 2011
LMS 3.2.1, what is the correct baseline template syntax to accomplish the requirement 2:
Requirement 1
• Check if the router is running H323: You can do it looking for the command “h323-gateway voip interface”. If that command is found on a router then it is an H323 voice gateway
• Configure the global command: voice class h323 1
[Code]...
View 1 Replies
View Related
Sep 14, 2011
I cannot edit or save file on a network drive. When saving or editing it says it cannot save and gives a read only error. I have tried to create a new folder and place files within but I still get the same error over and over again. When I check out the read only tab it comes back again.
View 1 Replies
View Related
Feb 19, 2011
I want to edit existing wireless network in DLINK router. But I can't find any option to do it. If I go to "wireless settings" option, it shows the three options "wireless network setup wizard", "add wireless device with WPS", "manual wireless network setup", but I cannot find any option to edit the wireless network that was already set up.
View 3 Replies
View Related
May 3, 2012
The business i work for uses a "Do it myself" template for their website. (this is through their webhosting company). I can not add FTP to this website, we have to completely redo it with code and whatnot in order to have access to FTP. We would like users to download a template from our website (no problem) and then send us their artwork files back to us. These can be upwards of 150mb. Is there another option that i am not aware of to do this? Can't use email, has a limit of 25mb.
View 6 Replies
View Related
Feb 13, 2013
I have recently purchases a Cisco srp547w for my organisation. It is working fine with one SSID enabled. I have configured everything with no problems using the Web interface. However, whenever I click the Edit button, in the Security column, in the Wireless Table under Basic Wireless Settings I get a pop up message which says :"Some values have been changed. The router must restart the wireless module to take effect.Please wait several seconds" I have tried this using 3 different browsers and get the same behaviour in each browser.
View 1 Replies
View Related
Feb 4, 2013
According to cisco manual in order to change SDM template i need to reboot switch, but when i have C3750-X stack do i need to reboot stack or maybe will be enough reboot in sequence the stack members?
View 3 Replies
View Related
Jun 11, 2013
I attempted to assign a User Roles template to a## 2504 controller and if failed with message stating controller version not supported. My current WCS version is 7.0172, if I upgrade to the lastest version will that resolve the template issue?
View 4 Replies
View Related
Sep 18, 2011
I have WRT54GS I can't view the setting tab to check or change. It seem the tabs are light in color and I click on them. I did have a virius which I got rid of. I have removed the linksys software and re installed
View 1 Replies
View Related
Feb 6, 2012
When using Cisco IOS c2960-lanbasek9-mz.122-50.SE3.bin we can delete line in SNMP group config with
no snmp-server group <group-name> v3 priv context vlan-<vlan-id>
without problems.
But, after upgrade on version c2960-lanbasek9-mz.122-58.SE2.bin there is output:
#####% Ambiguous command: "no snmp-server group <group-name> v3 priv context vlan-<vlan-id> "
It looks like some bug, but there is nothing in the bug toolkit.
View 2 Replies
View Related
Mar 26, 2013
I got myself lately Cisco SR520 router with some basic firewall functions built in. This is going to be used for my home broadband, so no need to be really super secure, as it would be for some business. I managed to configure it, however there are few things on the firewall side, which I don't understand.
This router had some default configuration in it's flash, when I bought it. There are class maps.... how it works or how to add/edit rules. Also, do I need to use class maps, or can they be replaced by ACL's to certain extend? How to add/edit class maps rules to allow certain port (eg. 3333). Pease see below part of the default config:
class-map type inspect match-any SDM-Voice-permit
match protocol sip
class-map type inspect match-any sdm-cls-icmp-access
match protocol icmp
match protocol tcp
[Code]...
View 1 Replies
View Related
Sep 21, 2011
Network Resources - Network Devices and AAA Clients- File Operations - Add - gives me File Format Validation Faliled. I am carefull to leave the header as it is. The header in the Import Template looks faulty, see attached. When exporting devices I also get the same header as attached. I also tried to change the header so its all in one column, but with same result.
View 1 Replies
View Related
Nov 30, 2011
is it possible to create some Configuration Template that pushes configurations only to switches or interfaces with a certain actual existing configuration element- e.g. a certain interface description?
Example:Template Parameter Mask asks User for an Interface Description- the User enters e.g. "A101" Second Parameter asks User for an access vlan to deploy to this interfaces- e.g. " 10"
So during deployment LMS make a "switchport access vlan 10" only on interfaces that contain the description "A101".
I know this is possible via Compliance Check/Deploy, but we want to make this more User friendly and flexible so that e.g. a Helpdesk Member can use this Template to easily change the VLAN based on a interface description (which refers in this case to a CAT5 outlet label).
View 1 Replies
View Related
Apr 12, 2012
We are trying to get the waep template (default no changes) from the Cisco WebAuth bundle to work on a 5508 controller.
We've setup the controller to use the custom login.tar that comes with the waep template folder in the bundle. We setup the WLAN to work off the global template and we used the config network web-auth secureweb disable command to allow only http rather than https (which is supposed to work in 7.2 code)
When we test with the custom bundle, we get no answer from the controller, just a url of [URL]
If we turn custom off, and use internal everything works...
Just to be clear.. we aren't looking for authentication (user and pass) we are trying to do the enter your email and click accept to the aup method.
View 5 Replies
View Related
