Cisco :: LMS 4.2 Device Inline Edit

Jul 15, 2012

In previous versions of LMS, I navigated to RME - Devices - Inline Edit to increase the snmp timeout.  I haven't been able to locate the same process in LMS 4.2. Where I can locate this feature?

View 1 Replies


ADVERTISEMENT

Cisco WAN :: Ios 12.4 Power Inline Time Range?

Feb 4, 2013

i have a ip-cam that is connect with power inline on my cisco router, i want to scheduler a reboot daily, of this ip-cam is there a posibility to use a daily time (time-range) to shutdown the interface and back up, or shutdown de inline power on this interface and back up ? i have ios version 12.4

View 4 Replies View Related

Cisco Application :: Installing 294 Inline At A Site

Apr 8, 2012

I have a new deployment I am working on.  I am unclear on the Inline setup. One location is configured as a trunk between the router and the switch, with voice and data traffic going through it. We will be installing a 294 inline at this site.What impact will it have on voice traffic?  We are using G0/0 for management, not the Inline interfaces. Is that any additional configuraiton needed to inline if done this way? I didn't get prompted for vlan ID, or anything like that during the setup as an accelerator.Are these setup with default optimizations out of the box, or is there additional programming needed once they are online?  I found where to build custom applications, but wonder if there is anything needed to be done once they are online for default traffic.

View 1 Replies View Related

Two Inline Routers But No Internet Access

Jul 17, 2011

I am having issues getting my (now former) routers to have internet access. They also kept seeming to become unresponsive when trying to change the settings and continual resets were necessary. 2 of them have now lost a battle with a sledgehammer and before I acquire a new one I want to know if my laptop is somehow infecting these routers, because 3 of them had similar symptoms before they met their fate with a 12 lb sledgehammer.This is in an apartment complex. Next to the cable modem, there is a Netgear router. This router has 4 outputs with ethernet cable going to 3 different apartments, one of them is mine which is in a separate building 200 hundred feet away. Rather than run an ethernet cable this distance, I made a reflective enclosure installed it under a carport and broadcast a signal to my apartment, and this worked great for 3 years. When the router next to the cable modem failed and was replaced, my personal router would no longer transmit the internet to my apartment.

View 11 Replies View Related

Cisco Application :: ACE 4710 Inline VS One-armed Based

Apr 3, 2012

I have 2 basic questions I am having doubts about it and would love to have some clarifications:
 
1) I configure in one ACE4710 (running 4.2.2) context a bridged interface and in another context the same interface, like here below : [code] Then I move to the Juniper context and I try to create an interface (either L-2 or L-3) but it doesn’t work: [code] So if I configure an interface as bridged in one Context, I cannot configure it in another context??
 
 2) If I want to migrate in context Microsoft from One-armed to inline (L-2 bridged), can I migrate one service at the time ( I.e. the config i showed above for context Microsoft, would it work also for one-armed based???)

View 1 Replies View Related

Cisco Switching/Routing :: No Inline Power On A 4506-E Port?

Oct 24, 2010

We have just purchased and installed a 4506-E chassis.  It contains a supervisor, two POE blades and 3 non-poe blades.  Version is 12.2(53)SG1.  Anyhoo, one of the ports isn't providing power to an IP phone.  We can plug the phone into any of the other POE ports and it works fine.  Is there a way to test an idividual port for POE problems?  What could the problem be?  The port works for normal data but will not provide power.

View 12 Replies View Related

Cisco AAA/Identity/Nac :: 1.1.1 / Unable To Register ISE Inline Posture Node

Oct 19, 2012

i'm stuck at registering inline posture node to primary node. I doing fresh install both ISE appliance using version 1.1.1, patched all 3 available patach version after install. AD and DNS were perfectly configure, ping using hostname able to resolve Everything  set, so both PSN and iPEP generate CSR and ready to let CA server to  signed. But anyway this is the outcome i get Error message "Unable to  authenticate. please check server and CA certificate."

01. - What certificate template to be use primary node and inline posture node?  I  having problem the CA certsrv won't show computer template for inline  posture node. can i use web server template and on the extension include  client autthenticaiton andserver authentication on this case?
 
- What certficate template use for primay node CSR?
  
02. According to Cisco ISE user guide 1.1.1, it mentioned "Creating certificate trust list in Primary ISE Node"
 
So  first action is importing Root and CA certificate . my rootCA.cer  import to certification operation certifcate store, while CSR  generated then Bind CA certificate. question, should i check anything like "Tust for client authentication" checkbox or any other option to be check? How about Inline Posture node, should i export the CA certificate and import to primary node's certificate store?

View 3 Replies View Related

Cisco Switches :: Not All SG300 Ports Supplying Inline Power?

Feb 26, 2012

Essentially, not all ports on our brand new SG300-28P switches provide Inline Power to our older 7900 series phones. I can connect the phone a couple ports down and it usually powers up, but not always. Often I can also connect an 802.3af device to one of the troublesome ports and it will received power, however I am noticing there are some ports that now refuse to supply PoE at all?
 
This is equipment that has been running perfectly fine for several years now, on C3524 PWR XL switches. I can also tell you that this is not isolated to one switch, but all 5 of our SG300 access switches. And, yes, the firmware has been updated to 1.1.2.0.

View 5 Replies View Related

Cisco Switching/Routing :: No Power Inline Commands On 1921?

Jan 27, 2013

I am running a 15.1 or so version of the IOS on a 1921 router. I have plugged in the external PoE injector into the router, and the PoE light on the front of the case is lit green. I have no options in the IOS to enable power on the EHWIC ports. I have most licenses enabled, including data and security.

View 6 Replies View Related

Cisco Switching/Routing :: Power Inline From PoE Blade (4548 / 4648)

May 3, 2010

I have a LAP-1142 connected to one of our PoE blade in our 4506 switch, it used to work fine with the following power consumption:
 
Interface Admin  Oper            Power(Watts)     Device              Class                            From PS    To Device                    --------- ------ ---------- ---------- ---------- ------------------- -----
Gi4/3     auto   on         21.5       20.0       AIR-AP1252AG-A-K9   3
 
However, we had power issue on Apr 28, so it failed and we saw from the log below:
 
Apr 28 13:57:38.990: %C4K_ETHPORTMAN-3-INLINEPOWEROVERDRAWN: Inline powered device connected on port Gi4/3 exceeded its hardware protection threshold.Apr 28 13:57:39.694: %PM-4-ERR_DISABLE: inline-power error detected on Gi4/3, putting Gi4/3 in err-disable state After the power restored later, the other LAP connecting with the same blade restored without any problem, except this one:
 
Interface Admin  Oper            Power(Watts)     Device              Class                            From PS    To Device                    --------- ------ ---------- ---------- ---------- ------------------- -----
Gi4/3     auto   on         16.6       15.4       Ieee PD             3

View 13 Replies View Related

Cisco Switching/Routing :: PoE Error On 6500 / Inline Power Module

Feb 12, 2012

Cisco IP phones attached to a Moduke in one of my Cat6500 access Switches suddenly went down. Upon closer  inspection of the Switch Sys log, I observed the following Sys log error messages:   [Module 9 is experiencing the following error: Inline Power Module - PS Voltage bad. ]A sh Mod output indicates the PoE daughter card and Main Module are "ok" - see attached output. It appears issue is related to the the actual Power Supply module and not the blade module and installed PoE Daughter card. I am inclined to open a TAC case for a PS replacement, but wanted to see if this can be resolved without a hardware replacement. At this time all 48 IP phones attached to this module are out of Service.

View 2 Replies View Related

Cisco :: WCS 7.0 Cannot Edit AP Migration Template

Jun 24, 2010

Have upgraded WCS to 7.0 due to a Mesh network feature we needed, but now see I can no longer edit the AP migration templates. The interface allows me to create or delete them but the command dropdown box does not show an Edit option. So now for every AP I want to migrate I need to create a new template before I can select the AP's and migrate them. I still need to migrate about 220 APs....
 
Looking though the function it tells me to click on the Migration Template name. However neither in MS IE nor Firefox this works, there is no link activated.

View 7 Replies View Related

Cisco AAA/Identity/Nac :: ISE-3315 / Procedure To Join ISE Appliance Become Inline Posture Node

Oct 17, 2012

I would like to ask, given that i got 2 units of ISE-3315 appliance, one need to be primary node for admin-policy service-monitoring, another unit then become Inline posture node.For the preparation on line posture node, what shoud i do on it?
 
01. For the unit ready to become inline posture node, so I just boot it, install the OS from sractch (using version 1.1.1), then start the initialize setup etc, like Normal setup?
 
02. Before i regieter, what is the deployment nodes i should select for inline posture node unit? provided the admin-policy service-monitoring will become primary node, and registration for inline posture node will be next action.

View 10 Replies View Related

Cisco Switching/Routing :: 3560v2 / Ws-c3560v2-48ps-s (inline Power Failure)

Jul 22, 2012

I have a switch 3560v2 with an IOS 12.2(50) SE1.All the lights ON and console error message below:POST: inline power post failed for port 0 up to port 15.Then, the system hanged and all lights (indicator) ON.

View 5 Replies View Related

Cisco Routers :: How To Edit RV180W Configurations

Dec 9, 2012

We are deploying over 20 RV180W Routers for a client and need to find a faster way to configure them for shipping.We have created a base image (all settings that will be shared between the 20 locations), we need an easy and quick way to make IP changes for the 3 VLANs and Local Security Groups for the IPSEC VPN.I tried to edit the CFG file by hand, but the checksum fails when it is loaded into the RV180W.How can I accomplish this? Can I manually create the checksum?Can I remove the checksum? 

View 3 Replies View Related

Cisco :: Edit SSID Password On 5508 Controller

Oct 3, 2012

Been a while since I have conf'd a controller. I believe its WLAN/edit/security/layer2 and below psk format edit the password?

View 2 Replies View Related

Cisco Switching/Routing :: How To Edit Port On 6509

May 15, 2013

I am very new to configuring ports on a switch. My boss usually does the port configurations but I am starting to learn some of the basic commands. The commands I know how to do are; close a port by typing config t, int gi0/port# and typing shut. I know how to enable a port, but how can I add info to a port or copy settings from one port to another?

We have some ports that are configured for 192.168 addresses but most are 10.128 addresses. I need to configure a certain port to be able to receive 192.168 addresses.

View 2 Replies View Related

Cisco Switching/Routing :: 6500 / How To Edit VACLs

Mar 7, 2012

I have to add some new ACEs on a Critical production 6500 running CatOS.The documentation that I have seen so far explains how to create, commit and vlan map a VACL ... however I see no instructions or comments on best practices for editing VACLs.

View 1 Replies View Related

Cisco Switching/Routing :: To Edit Configuration In 1800 Router

Jan 11, 2012

I am new user of cisco router i can access the hardware and login in the account but the problem is if i use the command "enable" asking for a password, old I.T. personnel who setup this router already resign.

View 2 Replies View Related

Cisco :: 3750 How To Edit Threshold Values For Optical Links

Jan 10, 2013

I have a switch where the current power threshold is set to -20.0db.  The problem is that the receive power fluctuates between -19.9db to -20.1db, which is causing it to throw alarms on my solarwinds monitoring server.  What I would like to do is change it to a different warning threshold, but I can't seem to find the command to do so.  This is a catalyst 3750 running IOS version 12.2(55)SE3. [code]

View 5 Replies View Related

Cisco AAA/Identity/Nac :: ACS 1121 Running 5.2 - Edit Hosts File?

Apr 13, 2011

Is it possible to edit the hosts file on an ACS 1121 server running ACS 5.2? Our problem is we have a single domain with multiple domain controllers at different sites. So when the ACS server tries connecting to the domain it randomly picks a domain controller which it can't connect to thus causing it to fail.

View 5 Replies View Related

Servers :: Can't Edit Or Save File On A Network Drive

Sep 14, 2011

I cannot edit or save file on a network drive. When saving or editing it says it cannot save and gives a read only error. I have tried to create a new folder and place files within but I still get the same error over and over again. When I check out the read only tab it comes back again.

View 1 Replies View Related

How To Edit Existing Wireless Network In DLINK Router

Feb 19, 2011

I want to edit existing wireless network in DLINK router. But I can't find any option to do it. If I go to "wireless settings" option, it shows the three options "wireless network setup wizard", "add wireless device with WPS", "manual wireless network setup", but I cannot find any option to edit the wireless network that was already set up.

View 3 Replies View Related

Cisco Routers :: Srp547w Restarts When Edit Security In Wireless Table?

Feb 13, 2013

I have recently purchases a Cisco srp547w for my organisation. It is working fine with one SSID enabled. I have configured everything with no problems using the Web interface. However, whenever I click the Edit button, in the Security column, in the Wireless Table under Basic Wireless Settings I get a pop up message which says :"Some values have been changed. The router must restart the wireless module to take effect.Please wait several seconds" I have tried this using 3 different browsers and get the same behaviour in each browser.

View 1 Replies View Related

Linksys Wireless Router :: WRT54GS - Can't View Setting Tab To Edit

Sep 18, 2011

I have WRT54GS I can't view the setting tab to check or change. It seem the tabs are light in color and I click on them. I did have a virius which I got rid of. I have removed the linksys software and re installed

View 1 Replies View Related

Cisco Switching/Routing :: C2960 - Edit Vlan SNMP Group Context?

Feb 6, 2012

When using Cisco IOS c2960-lanbasek9-mz.122-50.SE3.bin we can delete line in SNMP group config with 

  no snmp-server group <group-name> v3 priv context vlan-<vlan-id>
without problems.
 
But, after upgrade on version c2960-lanbasek9-mz.122-58.SE2.bin there is output:
 
#####% Ambiguous command:  "no snmp-server group <group-name> v3 priv context vlan-<vlan-id> "
 
It looks like some bug, but there is nothing in the bug toolkit.

View 2 Replies View Related

Cisco Firewall :: SR520 ADSL Router - How To Add / Edit Class Maps Rules

Mar 26, 2013

I got myself lately Cisco SR520 router with some basic firewall functions built in. This is going to be used for my home broadband, so no need to be really super secure, as it would be for some business. I managed to configure it, however there are few things on the firewall side, which I don't understand.

This router had some default configuration in it's flash, when I bought it. There are class maps.... how it works or how to add/edit rules. Also, do I need to use class maps, or can they be replaced by ACL's to certain extend? How to add/edit class maps rules to allow certain port (eg. 3333). Pease see below part of the default config:

class-map type inspect match-any SDM-Voice-permit
match protocol sip
class-map type inspect match-any sdm-cls-icmp-access
match protocol icmp
match protocol tcp
[Code]...

View 1 Replies View Related

Netgear DGND3700 USB Storage - Unable To Edit Settings For Shared Folder?

Dec 13, 2011

Have just had a stab at using my Netgear DGND3700's USB drive sharing - I had a spare external HDD + I want to be able to access files on it both over the 'net and from local network. Both work fine, very easy to set up, however I am unable to edit settings for the shared folder, which means I am unable to password protect it.

I don't need a password for local sharing but obviously it isn't ideal to have files freely available on the Internet, have looked into troubleshooting but can't find any similar stories with Netgears.I click "edit" or "create network folder" and it loads for a second or two but just stays on the same page. There is only one option to select but I have tried clicking the radio button first anyway, then clicking edit, same result.

View 1 Replies View Related

Linksys Wireless Router :: WRT610N No Access To Edit Any Settings On The QOS Page

Mar 11, 2012

I entered some QoS settings and now when I load the QoS page I get this Javascript error message in Firefox.Error: missing ) after argument list Source File: [URL]. Line: 100, Column: 47 Source Code: QosList[0] = new QosEntry('0','3','0','Kathy's Mac','3', infor);

Basically, the Javascript chokes on any computer name that you enter that has an apostrophe in it. As a result, I don't have access to add or edit any settings on that page. Seems like a major rookie mistake, especially for a major network device manufacture.

View 1 Replies View Related

Linksys Wireless Router :: E3000 Can't Create Shares / Nor Edit Public Folder

Dec 5, 2011

I have a Western Digital "WD 6400AAC External MYBook that I can not create shares on, nor edit the public folder.  In each case, I receive the message "Error on page".  I've updated my firmware, several time, to the latest build. I've formatted the my WD drive using the router and my computer, and each time I try to create a share, "Error on page" shows on the bottom left corner of the page and nothing happens.  I tried several other drives and the results are the same. 

View 1 Replies View Related

Cisco Switching/Routing :: WS-C3560-48PS-S Show Power Inline But No Power Available

Apr 14, 2013

We have two switches of the same model (WS-C3560-48PS-S) that are not providing PoE. I'm trying to remotely determine what the cause of the issue is.
 
Here is some output.
 
Hostname#show power inlineAvailable:0.0(w)  Used:0.0(w)  Remaining:0.0(w)
Interface Admin  Oper       Power   Device              Class Max                            (Watts)--------- ------ ---------- ------- ------------------- ----- ----Fa0/1     auto   off        0.0     n/a                 n/a   15.4Fa0/2     auto   off        0.0     n/a                 n/a   15.4Fa0/3     auto   off        0.0     n/a                 n/a   15.4Fa0/4     auto   off        0.0     n/a                 n/a   15.4Fa0/5     auto   off        0.0     n/a                 n/a   15.4Fa0/6     auto   off        0.0     n/a                 n/a   15.4Fa0/7     auto   off        0.0     n/a                 n/a   15.4Fa0/8     auto   off        0.0     n/a                 n/a   15.4Fa0/9     auto   off        0.0     n/a                 n/a   15.4Fa0/10    auto   off        0.0     n/a                 n/a   15.4(code)

View 1 Replies View Related

Cisco Firewall :: Unable To Edit IP Based ACL Firewall Rule In RVS4000?

Apr 8, 2012

I am a novice with networks but do have a fair understanding of networks. I have a small business network, utilizing a RVS4000 router (Firmware V2.0.27)I am attempting to set up firewall rules to block certain web sites at certain times.I have successfully set up rules using source and destination ranges, to deny service 24 hours a day everyday.
 
However and here is the problem when I attempt to edit any of the rules (I want to change the time to certain hours of the day) it allows me to edit the rule but when I attempt to save I get an error message up saying there are invalid characters and it will not save the changes?create the whole thing with the changes I want it works fine, is this a known bug?

View 1 Replies View Related

Cisco :: LMS 3.2 Failed To Start Acquisition / Device Unreachable / Enter A Valid Device

Jan 3, 2013

We are using LMS 3.2.1 with SP1 and Campus Manager 5.2.2.Server runs Windows 2003 R2.Everything runs fine except for User Tracking on two Catalyst 6500 switches running CatOS. These devices are discovered, reachable, SNMP works fine, neighbors seen. But when we try to launch acquisition, the UT utility complains with this error message:"Failed to start acquisition: Device unreachable. Please enter a valid device."When we wanted to add ports via Device Trap Configuration, LMS has fired a different error message: "There are no ports to configure for the selected device(s).Check whether you have selected any router(s)." I have checked the portsData.xml file, which doesn't have any ports included for the two devices: [code] We have tried to exclude / include the switches in the data collection, but that didn't work.

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved