Cisco Switching/Routing :: No Inline Power On A 4506-E Port?
Oct 24, 2010
We have just purchased and installed a 4506-E chassis. It contains a supervisor, two POE blades and 3 non-poe blades. Version is 12.2(53)SG1. Anyhoo, one of the ports isn't providing power to an IP phone. We can plug the phone into any of the other POE ports and it works fine. Is there a way to test an idividual port for POE problems? What could the problem be? The port works for normal data but will not provide power.
View 12 Replies
ADVERTISEMENT
Apr 14, 2013
We have two switches of the same model (WS-C3560-48PS-S) that are not providing PoE. I'm trying to remotely determine what the cause of the issue is.
Here is some output.
Hostname#show power inlineAvailable:0.0(w) Used:0.0(w) Remaining:0.0(w)
Interface Admin Oper Power Device Class Max (Watts)--------- ------ ---------- ------- ------------------- ----- ----Fa0/1 auto off 0.0 n/a n/a 15.4Fa0/2 auto off 0.0 n/a n/a 15.4Fa0/3 auto off 0.0 n/a n/a 15.4Fa0/4 auto off 0.0 n/a n/a 15.4Fa0/5 auto off 0.0 n/a n/a 15.4Fa0/6 auto off 0.0 n/a n/a 15.4Fa0/7 auto off 0.0 n/a n/a 15.4Fa0/8 auto off 0.0 n/a n/a 15.4Fa0/9 auto off 0.0 n/a n/a 15.4Fa0/10 auto off 0.0 n/a n/a 15.4(code)
View 1 Replies
View Related
Jan 27, 2013
I am running a 15.1 or so version of the IOS on a 1921 router. I have plugged in the external PoE injector into the router, and the PoE light on the front of the case is lit green. I have no options in the IOS to enable power on the EHWIC ports. I have most licenses enabled, including data and security.
View 6 Replies
View Related
May 3, 2010
I have a LAP-1142 connected to one of our PoE blade in our 4506 switch, it used to work fine with the following power consumption:
Interface Admin Oper Power(Watts) Device Class From PS To Device --------- ------ ---------- ---------- ---------- ------------------- -----
Gi4/3 auto on 21.5 20.0 AIR-AP1252AG-A-K9 3
However, we had power issue on Apr 28, so it failed and we saw from the log below:
Apr 28 13:57:38.990: %C4K_ETHPORTMAN-3-INLINEPOWEROVERDRAWN: Inline powered device connected on port Gi4/3 exceeded its hardware protection threshold.Apr 28 13:57:39.694: %PM-4-ERR_DISABLE: inline-power error detected on Gi4/3, putting Gi4/3 in err-disable state After the power restored later, the other LAP connecting with the same blade restored without any problem, except this one:
Interface Admin Oper Power(Watts) Device Class From PS To Device --------- ------ ---------- ---------- ---------- ------------------- -----
Gi4/3 auto on 16.6 15.4 Ieee PD 3
View 13 Replies
View Related
Feb 12, 2012
Cisco IP phones attached to a Moduke in one of my Cat6500 access Switches suddenly went down. Upon closer inspection of the Switch Sys log, I observed the following Sys log error messages: [Module 9 is experiencing the following error: Inline Power Module - PS Voltage bad. ]A sh Mod output indicates the PoE daughter card and Main Module are "ok" - see attached output. It appears issue is related to the the actual Power Supply module and not the blade module and installed PoE Daughter card. I am inclined to open a TAC case for a PS replacement, but wanted to see if this can be resolved without a hardware replacement. At this time all 48 IP phones attached to this module are out of Service.
View 2 Replies
View Related
Jul 22, 2012
I have a switch 3560v2 with an IOS 12.2(50) SE1.All the lights ON and console error message below:POST: inline power post failed for port 0 up to port 15.Then, the system hanged and all lights (indicator) ON.
View 5 Replies
View Related
Aug 19, 2012
I have two Cisco 4506's running cat4500-ipbase-mz.122-50.SG3.bin. Periodically, when attaching a new workstation to these switches the Mac Address of the device disappears off the port when the device is connected or the port is configured. The only way to correct the issue is to do a hardware reset on the blade or reboot the switch. After resetting the blade or rebooting the switch the devices will start showing up on the port and connect. This does not effect devices that are already connected to the switch, just newly added devices
Both switches are populated with WS-X4148-RJ45, WS-X4148-RJ45V and WS-X4248-RJ45V blades. It doesn't matter which blade the new device is being connected to. I believe that this may be a "Bug" but have been unable to locate one.
View 3 Replies
View Related
Feb 4, 2013
i have a ip-cam that is connect with power inline on my cisco router, i want to scheduler a reboot daily, of this ip-cam is there a posibility to use a daily time (time-range) to shutdown the interface and back up, or shutdown de inline power on this interface and back up ? i have ios version 12.4
View 4 Replies
View Related
Feb 26, 2012
Essentially, not all ports on our brand new SG300-28P switches provide Inline Power to our older 7900 series phones. I can connect the phone a couple ports down and it usually powers up, but not always. Often I can also connect an 802.3af device to one of the troublesome ports and it will received power, however I am noticing there are some ports that now refuse to supply PoE at all?
This is equipment that has been running perfectly fine for several years now, on C3524 PWR XL switches. I can also tell you that this is not isolated to one switch, but all 5 of our SG300 access switches. And, yes, the firmware has been updated to 1.1.2.0.
View 5 Replies
View Related
Feb 28, 2013
I have 2 3560 switches that are running 12.2(25)SEE2. Port security is enabled on some of the ports. Whenever there is a power failure, when power is restored, 1 port on each switch goes to err-disabled. The mac address that causes this is a valid address for that port. Below is the configuration on one of the ports.
View 1 Replies
View Related
Jan 17, 2013
My management has tasked me to give them a high level overview of the different switching we can choose for our new building.
This is what I know so far.4 Closets, each closet has 450 ports,One MDF room that is will contain one UCS Chassis and a Nimble iSCSI SAN.
I am working on the spreadsheet and it looks like this (Not totally filled):
2960s3560x3750x45064510Approx cost (Each, 48PORT, POE+, 10G uplink, Dual PS, IP BASE)
6K7K8K45K75KMax Capacity192432432192384Backplane speed206464520520ProLeast ExpensiveStackable to 9Stackable to 9ProDual PSDual PSDual PSDual PSDual PSProLayer 3 opt
Layer 3 optDual SupsDual SupsConExpensiveExpensiveConNo Dual PSConLayer 2 OnlyCannot stack more than 4
For the MDF I would like to use 2 Nexus 5548's with FEX's, and the layer 3 daughter board. For the IDF's I was thinking of two 4010's.
View 12 Replies
View Related
Jun 9, 2013
I am receiving the following error on 3750 stack switches. have already verified the power status and found ok.
IOS used: Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
211540: Jun 10 10:45:17.935 UTC: %PLATFORM_STACKPOWER-4-UNBALANCED_PS: Switch 4's power stack has unbalanced power supplies
211541: Jun 10 10:46:18.045 UTC: %PLATFORM_STACKPOWER-4-UNBALANCED_PS:
[Code]....
View 1 Replies
View Related
Sep 4, 2012
After stacking two 3750X switches, with four equal power-supply's, with StackWise and PowerStack , still got the next message every few hours %PLATFORM_ENV-1-FRU_PS_ACCESS: FRU Power Supply is not responding (gn4m-rt1p08-04-2)( note that the message revers to the second switch in the stack ) although the stackwise and powerstack on the switches is oke and are working correctly. !
Config : Stack-power in power-sharing mode/strict With CLI on the switch : All the power supply's and stack-power details, prio look OK.
Only: LMS prime /inventory/cisco-view/configure/power supply status result : some power supply's are marked as disabled.with the command > power supply 2 slot a off/on I manage to get the status back to "normal", but after a few hours some power supply's are again marked as "disabled".
Looks like SNMP en IOS difference from opinion.
Hardware
WS-C3750X-24S-S
C3KX-PWR-350WAC
Software
15.0(2)SE
C3750E-UNIVERSALK9-M
View 5 Replies
View Related
Feb 28, 2011
I have a 6500 chassis with 2 power supplies. At the moment I am using the default configuration:
power-redudancy mode redundant
The problem is that an inserted module is in "power deny" state due too insufficient power.
I know, that It's not a good idea to change into combined mode (loss of redundancy), but my customers requested this anyway.
So I will change to combined mode. So here's the 1 million dollar question: "Which modules will go into power deny, if one of my power supplies fails?"
The 6500 config guide states:
"Power supply is removed withredundancy disabled
• System log and syslog messages are generated.
• System power is decreased to the power capability of one supply.
• If there is not enough power for all previously powered-up modules, some modulesare powered down and marked as power-deny in the show power oper state field."
Well, do you know if there's any way to configure some kind of priority? E.g. I definetly don't want by 10Gig Module or WiSM module to be in power deny. Can i statically make sure, those module will be powered on for sure? Like: "power enable module slot_number" How is this calculated? Or is random?
View 3 Replies
View Related
Apr 4, 2012
In a stand alone 3750x switch configuration, can the secondary power supply only act as a redundant power supply (active/standby), or can it become a "pool" of power similar to power sharing mode for StackPower (somewhat active/active)? I understand there is no stack involved here but I'm curious if this functionality is possible.
View 1 Replies
View Related
Dec 19, 2011
I am implementing a guest wireless network to work alongside my internal network. The guest network will use the existing switching network and will be separated by VLANs. I have the ASA set so that traffic can get to it and out to the Internet. I can set up a workstation on the same VLAN as my guest network and can route inside my network (strictly doing this for testing purposes). Where I am having problems is with the Catalyst 4506 switches and the ip routing. I had two separate "ip route" statements defined on my switches.
ip route 10.200.2.0 255.255.255.0 10.200.2.254
ip route 0.0.0.0 0.0.0.0 10.100.100.254
I have discovered that the traffic is always following the default route despite the fact that my IP address on my test workstation falls in the 10.200.2.x network. I was looking at documentation and found that it is possible to set up policy-based routing on the core switches. Can you have two "ip route" statements defined like this to segreate traffic or do I have to use PBR for routing (or a combination) in this case? If I define PBR then how does that impact my existing routing? I need to make sure that I can still route the existing traffic while I'm configuring this change.
View 9 Replies
View Related
Aug 27, 2012
We have 2 sites, each with 2 x 4506 switches which will be connected togther using an etherchannel. The switches will provide access ports for client devices and will be configured with HSRP to provide gateway redundancy. SW1 will be HSRP active.2 metro ethernet links will be installed in each site which will connect back to our HQ sites. OSPF will be used over the backbone to provide resiliency and to allow shortest path routing to each HQ and to prevent traffic over the HQ to HQ link.
The 4506 will be trunked togther with an SVI for providing OSFP adjacency.For the traffic flow from SW2 to HQ2, traffic will hit SW1 and then route back to SW2 and then to HQ2. Is this the best way to do this? Should a second link be connected between switches just for routing or should something like GLBP be used?
View 6 Replies
View Related
Aug 31, 2012
CiscoSwitch1(4506) has 3 VLANs(12,13,14) and Switch2(4948) has 3 different VLANs(22,23,24) and IP routing has been enabled in both switches with SVI interfaces for each vlan. intervlan routing is works fine.Now there is a requirement to connect these switches together. Vlan 12 on the Cisco switch 4506 has to be made available from vlan 22 from Switch2(4948). basically Vlan 12 is having a multicast source (225.0.0.0 & 226.0.0.0) which should be accessabile from vlan 22 of cisco switch 4948.I got 2 ideas
1) Create a trunk between these switches and configure L2 vlan(12) in cisco 4948...i know theoritically it should work but what my concern is Ip routing enabled in both switches will it create any issues? is it a gud solution to this requirement?
2) Create a separate IP network on the ports connecting to both switches and set up routes to the networks.ex- console(config)#ip route 192.168.10.10 255.255.255.0 192.168.20.1.
View 8 Replies
View Related
Mar 8, 2013
I am configuring multicast in a environment where I have a 4506 at each site (4 total) and a 6506 as the core. Each 4506 is connected via layer 3 to the 6506. I have a mix of 3560s, 3548s, and 2960s connected to the 4506s and the 6506 via layer 2 trunk
I have multiple multicast sources and hosts communicating at a time (multiple cameras sending video / multiple computers receiving video). So this is not a scenario where there is 1 sender and many receivers. This would be many senders (~50) and some receivers (~10)
Sample Diagram:
->3560
|
6506 --> 4506 --> 3548
| |
| --> 2960
|
4506 --> 2960
|
-->3548
I configured ip multicast-routing on each of the 4506s and on the 6506. IGMP snooping is on by default on the 3560 and 2960 switches. CGMP is on by default on the 3548 switches.
I set up PIM sparse-dense mode and IGMP version 3 on each of the layer 3 interfaces for the 4506s and 6506 where they connect and on each VLAN that is sending or receiving multicast. Multicast is working throughout the network, however I am looking to verify the configuration as I scale this out to more clients on the network.
#1 - Is it correct to us sparse-dense mode in this configuration?
#2 - Do I need to configure a rendezvous points using AUTO-RP? (ip pim send-rp-announce INTERFACE scope TTL). Not sure here if I need to designate this and what to choose. Right now I do not have this and it is working, but documentation seems to infer that I need to designate this.
#3 - Is there any other configuration settings I should be considering? I hard to find real world configurations of multicast as examples or people that know multicast routing well.
View 3 Replies
View Related
Jan 4, 2013
I am currently running a 4506 with a sup V engine. I have purchased a sup 7 engine. Is there a guide on how to perform this task. I am sure I need to do an IOS update as well.
View 2 Replies
View Related
Dec 6, 2012
We have sup engine 6L(WS-X45-SUP6L-E) on two 4506 switch. both switches connected in LAN (HSRP primary and Secondary).
We are going to replace it with Sup7LE. What is the best procedure to get this done with minimal outage?Any other important thing to be noted ? Note : We have Lincence for SUP 7LE
View 2 Replies
View Related
Jun 11, 2012
We are attempting to PXE boot from clients obtaining their DHCP lease information from DHCP pools configured on our 4506. The PXE server, and the client are configured in separate VLANs. We have configured option 66 to point to the PXE server IP address, and the bootfile option to point to the PXE boot configuration filename. On the client side SVI, we also have configured the ip helper-address command to point to the PXE server (which also acts as another DHCP server for redundancy).
The PXE boot continuously fails stating it is unable to find the configuration file. If we remove the DHCP pool from the 4506, and allow the client to receive their DHCP lease info from the secondary server (Windows 2k8 - same server as PXE server), they PXE boot with no issues.
We have no problem obtaining DHCP info, just completion of the PXE process.
View 6 Replies
View Related
Mar 19, 2013
Does SUP 7E is comatible with IOS? It came with IOS-XE preloaded and there are no IOS software listed under downloads.
View 3 Replies
View Related
Apr 7, 2012
Yesterday I've faced a Problem that is not letting me boot with the new IOS.
Actually I'm planning upgrade IOS which supports SSH. As part of plan I've downloaded the new IOS image and uploaded via TFTP server to the switch.
After uploading to the switch. I've verified image and MD5 hash also. Everthing is fine. Then after I set the boot variable for the newly uploaded Image.
When I'm rebooting the Device it is not taking the new IOS. It's booting with the OLD image. Even It's not showing any error message while rebooting (ACTIVITY FILE ATTACHED FOR YOUR REFERENCE) I can't take risk by deleting the old IOS.
View 1 Replies
View Related
May 8, 2013
I have 4506 with below sup, my requirement is to enable netfolw , but as i came to know that it is not supported in this sup, is there any additional option which can be explored to get the netflow working without replacing sup.
Card Type Model
-------------------------------------------------------------+-----------------------
Sup 6-E 10GE (X2), 1000BaseX (SFP) WS-X45-SUP6-E
View 4 Replies
View Related
Dec 4, 2011
We ordered the wrong part number for a Cisco 4506 non-E chassis, the part number is: WS-X4624-SFP-E and the device is showing "Unsupported module"; What would the part number be for the non-E? WS-X4448-GB-SFP,Catalyst 4500 48-Port 1000Base-X (SFPs Optional) ?
View 1 Replies
View Related
Mar 14, 2013
i'm desperately trying to get LACP working over a dot1q Tunnel. The "Service Provider" Switches are two 4506-E Switches with SUP7-E connected via a 10G Link, running on cat4500e-universalk9.SPA.03.03.00.SG.151-1.SG
sample config:
dot1q tag vlan native
interface GigabitEthernet3/1
switchport access vlan 2001
[Code].....
View 4 Replies
View Related
Jun 8, 2012
a 6509 and a 4506 with 2, 1gb interfaces in a portchannel. Bring it up and everything is fine. Save the config and reload either switch and the interfaces stay in Not Connected state. Either doing a No Shut or a physical unplug the SFP and plug it back in will bring it up with no issues. Interfaces do not go into Err Disabled state they stay in Not Connected like there is no fiber plugged into it. No error mesages in the log. The Just the Interface is now up.Both are running very new code,
6509 - s2t54-ipservicesk9-mz.SPA.150-1.SY1.bin ( 15.0.(1)SY1 )
4506 - Version 03.02.00.XO
View 1 Replies
View Related
Aug 12, 2012
I have "inherited" a Catalyst 4506 with IOS version 12.2(20)EWA1 and Supervisor IV already installed. We recently purchased a second Supervisor IV and I am looking to install this second supervisor for redundancy. Is there anything special with installing a second supervisor or so I just physically install the new supervisor and the IOS will automatically set everything up?
View 3 Replies
View Related
Dec 18, 2012
I have a setup with two Cat 4506E working as a HA,I used a bundle 4Gb interfaces working as ether-channel,I'm facing a problem with DHCP pools on the both SW's,There is no problem if I use the pools on one sw,But when I but the pool on both sw's then I faced a lot of conflict IP in the DHCP pools,How can setup a real DHCP redundancy on both SW's,
View 6 Replies
View Related
Mar 25, 2013
My inherited network has a Cisco Catalyst 4506 with a WS-X4124FX–MT fiber card that connects to twelve Cisco 2950 switches over 62.5 micron multimode fiber at 100 Mbps. I do not know my run lengths (or even where the conduits run), but the furthest switches are well over a thousand feet from the server room. Any appropriate test equipment to provide this information soon.
We are looking at upgrading the main switch to a Catalyst WS-C4507+E with two WS-X4712-SFP+E cards and the closets to Cisco 2960S-48TD-L switches. Assuming this is a reasonable move, my question is about choosing the appropriate SFP’s for our current and future needs.
I am aware that 62.5 micron multimode fiber is the least favorable for extended lengths, but I will not be in a position to replace it for at least a year. If I purchase 10 Gbps modules, like the SFP-10G-SR or SFP-10G-LRM, can they “throttle down”, either automatically or by setting a parameter, to communicate at slower speeds over distances that exceed their 10 Gbps maximum link lengths on multimode fiber?
View 1 Replies
View Related
May 14, 2013
We want to permit certain mac addresses on the cat 4506 switch wherein only those mac addresses will get access to network.
Configuration Planned: For testing purpose we have created mac access list on cat 4506 and deny laptop mac address in this access list. The mac access group is applied to the port where the laptop is connected to cat 4506.Even after applying the mac access group on the port, the laptop is able to ping the vlan ip of cat 4506 [code]
laptop with ip address 192.168.10.2/24 connected to port 2/1 is able to ping 192.168.10.1 even after applying the mac access-group
Note-we have tested same configuration on cat 3560 and its working fine. We apply the mac access-group command on interface and clear the arp-cache and we are not able to ping vlan interface ip. The moment we remove the mac access-group,ping starts again.
View 4 Replies
View Related
Nov 30, 2011
I have three 4506 switches with vlan 4 set as the management vlan. Switch 1 is connected to switch 2 and switch 3.
I can access switch 1 and 2 using telnet from the management vlan and both switches reply to pings. But from switch 1 or 2 I cannot ping or telnet switch 3. If I plug into switch 3 and I can ping and telnet switch 3 but not switches 1 or 2.
It is as if the management vlan 4 is not being passed to/from switch 1 and 3. The configs for the uplinks from switch 1 to 2 and 3 are the same. And the configs for switches 2 and 3 look the same apart from the port settings.
I have over 40 vlans running all that work fine between all the switches.
View 28 Replies
View Related
