I have a problem in connecting SRP521w with CCA v3.2. I tried to connect the device with CCA but it said that that the device is unsupported. I already upgraded the router's firmware with v1.01.26.
Here is what the CCA looks like every time I try to connect with the router :
We recently switched from a ADSL2+ service to a 2Mb SHDSL link. Uploading images to our website is happening all day long, thus greater upstream bandwidth was required.
Our downloads are suffering somewhat, the upstream gets easily flooded and downloads start to trickle.
I have a SRP521W which has a few QoS options. The QoS Bandwidth control has upstream bandwidth set to 2048 Kbps. Now I don't know how to enforce anything. How to use the WAN strict high priority queue appriopirately.
The website has a static IP address, so I can target that in the rules to only use 80% of the bandwidth?Alternatively can I limit upstream traffic per user?
We've come across an issue whereby the WAN port fails to light up with an Adtran Total Access 832 (via bonded SHDSL) unit.
Eventually the WAN port does light up after connecting and disconnecting it several times with the ethernet cable. However as a test I power cycled the router with the WAN cable disconnected and had a strange issue where the WAN light would constantly flash and show up in the web gui as being connected when in fact the Adtran Unit showed the device was not connected at all.
This is the second Cisco SRP521W router in place as the original one disconnects overnight without any load and a power cycle would fix the issue, but this replacement router disconnects during business hours (even worse for the customer) and power cycling does not bring it back online. We've adjusted the WAN port to 10MB Full on both devices and hope that it stays up. I am wondering if any has had a similar experience? Would this be a behaviour of a faulty unit or may it not be compatible with the Adtran Total Access 832 (via bonded SHDSL) unit perhaps?
Cisco srp521w router vpn configuration. company has wan static ip to router. enable vpn Cisco server in router. connected with Cisco vpn client. route failed in log. Need to access a PC on the company site with address 192.168.15.105 and router with gateway 192.168.15.1.
How do i configure ip pool ? different ip address? if i connect how do i access pc 192,168.15,105 ? remote pc with 192.168.1.100.
I have a router SRP521W I wonder if you can setup a self-attendant or ivr to this device.
View 4 Replies View RelatedIs it possible to send all traffic through site to site VPN using SRP521W (on the other site ASA) ? Lets say, traffic to Internet from branch through HQ - site to site VPN between branch and HQ. I've tried to set up destination crypto policy entry to 0.0.0.0 0.0.0.0 but it's not accepted. Firmware version is 1.01.26 (003)
View 4 Replies View RelatedHave followed the admin guide, and can setup this up fine, however what we're wanting is to turn off any IP connection for the main wan ethernet interface and only have the sub-interface have an IP connection method.
I can't see how you can turn this off, which is causing a double-up of dhcp requests being sent when using both the main/sub ethernet interfaces to use dhcp.
This has been tested on the 521w and 521w-u versions, and I've just used the latest firmware 1.2.4 on the u version.
How can this be configured so that there is only 1 WAN interface that is using IP (the sub interface) Setting default routes to point to the sub interface doesn't make a difference.
Any recommendation for creating a configuration template for the SRP521W? I can use the Admin-->Backup Config to get a xxx.cfg file, but I cannot edit it with notepad++. Also, i know the config can be view via view-source: [URL], but how would I load a modified copy of this back to the router?
View 8 Replies View RelatedI am trying to create a VPN between a SRP521W (only point-to-point VPN) and a UC560 (VPN server) and it seems it doesn't works (SRP doesn't create the tunnel).
View 4 Replies View RelatedWe have been using a SRP521W as the main Router for an office with about 25 users.
So on the cable network it's about 25 computers, 25 IP Phones, 3 printers. Wireless network hold some smartphones and tablets. Computer traffic is 100% Remote Desktop.
That said, for the last few days network connectivity sucks. I think the problem is, precisely, the SRP521W. Some mornings the WAN link is down and can only be brought up by a router reboot.
There's an IPSec tunnel to HQ.
Wireless network was moved recently to a WAP121 to offload the SRP521W. It has two networks: internal and customers with two VLANs.
CPU Usage is around 30-45% all day and spikes to 100% sometimes. RAM Usage is 40-45%. I do not know if this is "too much", "average" or "really low load".
Anyway, time for questions:
a) How can I get a table of active connections on the firewall/NAT to see if there anything "strange" on the network traffic that maybe causing issues?
b) Is there any know bug in the VLAN handling of the SRP that maybe causing the issue? (it's one of the latests changes introduced).
c) If the problem is that there's too much load for such a small router, what replacement would you recommend given the details above? (remember I do not really need wireless on the router as I have the wap121).
I have one SRP521W-K9-G1 and need to provide guest internet access without access to my network. What is the best way to configure this?
View 3 Replies View RelatedJust brought another set of SRP521W, after changed the WAN setting to PPPOE, we unable to access the web management. The power/sys light will keep blink when trying to access the web management. We able to ping it. We tried the reset button but it did not work as well. Is that a way to upgrade the firmware without using the web management?
View 4 Replies View Relatedi cannot access the web managemnet interface of this router from a different subnet.THe WAN interface is a 4G LTE connection,I have disabled both the SPI firewall and NAT and enabled remote management from any ip address but i cannot access the admin web page from a remote subnet.Doing a port scan of the routers WAN or LAN address i cannot see any ports open at all...its as if firewall or NAT is still enabled somehow.
View 0 Replies View RelatedUsing a 3G USB Modem (Huwaei E153) the mobile network status is connected however the Wan Interface (AutoConfiguration -DHCP) is displayed as Disconnected (Physical layer disconnected).
View 2 Replies View RelatedAs you can see i have problems with connecting 2 SRP521W together for an VPN tunnel. I tried as much as I can but now i dont know what to do or how and where is the mistake? the connection between these two devices was there last week, after weekend (nothing changed in configs) the connection suddenly was interrupted, without any reason or warning. another day it worked again and 20 mins later connection was dead again...and now it wont establish at all.. here are some screenshots from the vpnconfigs of my devices. one has a static IP the otherone uses FQDN. These are the IKE policies: Here the IPsec Policies: and the GRE policies:
View 10 Replies View Relatedeverything was all good, my brother went crazy and unplugged everything.it effects our house phone too, that could be the problem.i just dont know what wires went where. all the wires are the same color.but i know which is which. just again, dont know where.i would like to get it done before he gets home later on.
View 1 Replies View RelatedI'm trying to make the VPN connection between two routers CISCO RV180w.I performed the basic configuration in cisco "server". I did the same in cisco "client".The following configuration and logs, do not know what to do ...
SERVER CONFIGURATION:
IKE Policy Configuration:
VPN Policy Configuration:
CLIENT CONFIGURATION:
[code]....
I have reset my RV082 router (both wit the reset switch and the factory default wizard) and run the setup wizard but regardless I can't connect to shaw.ca which is my service provider. I notice that if I use http://192.168.1.1 the browsers (IE & FF) default to https://192.168.1.1 and then I am prompted for a certificate. I can enter if I ignore the request but after getting in I simply cannot connect to my ISP.
View 4 Replies View RelatedI am having trouble with connecting to the Internet through the router. It has worked for 4 years now and all of a sudden it is not working at all. Any direction to getting reconnected. I have an Internet connection directly to the modem, and I can connect and log into the router admin panel, but it will not allow me to access the Internet through the router either wirelessly or by connecting directly to the router. All the lights come on and flash like normal and I have done a factory reset and still nothing.
View 6 Replies View RelatedHow to setup VPN connection,
Head office : fortigate 200b firewall - SSL, IPsec
Branch office: WRVS4400N Wireless-N Gigabit Security Router with VPN
Both side have the public IP.
I'm an IT professional with more than 10 years experience. I have spent last 5 days trying to figure out why the wifi connection to this router is so slow, but still no luck. I'm getting only 13Mbps even if my laptop is next to the router! (wired connection worked ok)
I have tried all sort of setting combinations, 2.4GHz/5GHz; N only/ G,N Mixed; Auto/20MHz bandwidth; different channels; WPA2 encrypted vs open; disable firewall; wmm enabled/disabled; 1.0.0.26/1.0.1.0 firmware... no matter what I try, I always get only 10 - 15Mbps speed.
Once I replace this router with my old router, it worked perfectly --- getting 70 - 80Mbps with exactly the same testing environment and configuration.
I really expect this router to offer much faster wireless speed according to this review: [URL]
My new RVS4000 (2.0.2.7) connects the WAN via PPoE with dynamic IP which is held at DynDNS and normally I see the RVS4000 via a router-to-router-VPN. That works fine so far, but every "some" days the router looses WAN connection (and with ist VPN). When this happens, last DynDNS-update is hours ago, so it didn`t reconnect. Looking on the routers site, the LAN is fully functional for clients that have got their DHCP-Information. New clients don`t get DHCP-Info (IP-address, DNS), both do not have internet access. The router`s WAN-summary shows, that it thinks to be "CONNECTED" but with empty WAN-IP and DNS entries. Klicking "DISCONNECT" and then "CONNECT" again solves the problem so far. The loss of connection is not the periodic break from the IPC, which is correctly identified and reconnected as configured. I wanted to trace the problem with the log, but there is also a bug. It stops logging at some time completely - neither email-log nor local log, so I never happend to be lucky to hit the point of loss of connection. Also the local log provides a first and next pages, but the next pages are always empty - not really useful.
View 3 Replies View RelatedLooking for assistance in setting up a VPN Connection on a RV120w.Trying to establish VPN with Android tablets utilizing Anyconnect.I currently utilize IPsec connections into RV120w without issues from desktops/laptops. (I am not real familiar with certificate based connection, and how to export from RV120w and import into Android)
View 2 Replies View RelatedI have 2 WAN connection @ my office. One is the static IP from Reliance Network
The other connection of WAN is dynamic from AIR TEL...
When i logged into my router. I can see the dynamic IP from Reliance on WAN1 status. But on WAN2 is see everything as 0.0.0.0. The WAN2 configuration has been set to get the IP automatically...
I tried the other solution offered by one of the support guys, by turning on and off the modem, but that does not work...
Or do i need to change the WAN2 connection to be PPoE or something...
We have two RVS4000 at both ends of a VPN tunnel. The tunnel is up and runs fine. I can ping the two servers at the main office end of the tunnel, and cconnect to the resources of both servers. However, one of the servers, the terminal server, is unreachable via RDP. The other server can be reached via RDP for administrative purposes just fine, but the terminal server cannot be reached. There is only one difference that I can think of. The terminal server is reachable from the outside world via a redirected forwarded port on the RVS4000 at the main office.
The current firmware version is V2.0.0.3 at both ends. Is this a known anomaly for this revision of firmware?
i got a problem in configuring a VPN Connection for our Colleagues (Laptops & Iphones 4/4S/5) We got an RV042G .
A WAN Connection from Deutsche Telekom AG with Static IP connected in WAN1. Configured for PPPoE. Ive got configured a Port Forwarding on our SBS 2011 Server for OWA and other Services on web. I´ve got extreme Problems configuring VPN Connections. We use Quick VPN, other tools got to much buttons to click .
1st i configured a Group VPN , with FQDN (Remote Group) Local Group (IP only) . i configured 2 users. Then on a Laptop connected to the internet through an Hotspot Connection of an Iphone.
I entered the WAN IP .. Username. Password. Pressed ENTER. I get to the point of Verifyiing Network, and after it timeout with Remote Gateway not responding. Do you want to wait. If i Press Yes, after max. 1 minute there comes the message again.
I looked in the VPN Summary, and i see, that my username was connected through VPN for seconds, but then disconnected. Do i have overseen an option to configure??
I have an SA520 setup and all my users can login to the SSL VPN tunnel except one user. The laptop is running windows 7 64bit and had IE9 installed. When I try to connect her to use an SSL VPN Tunnel, I get the following error: Cisco-SSLVPN-Tunnel Install Failed: Error in getting proxy settings!. I have made sure the firewall was turned off. How to get the ssl tunnel connected?
View 3 Replies View RelatedWRVS4400N needs to be manually connected when the power is recycled after power failure. Is there a setting to connect an IPSEC VPN automatically, instead of manually going in to connect the VPN
View 3 Replies View Relatedi got an issue with vpn and cisco rv100w, router is configured well and computers and iphone can connect with PPTP. Problem became when we map NAS drive from computer or we move data (1-4 Mb). Seems connection go down, speed is so slowly and drop the connection.Is it from router? or from Internet provider?
More data, If I connect to http of router/NAS .. all go fine, only when we need data from NAS (map drive by windows) copy, open files, ..., connection is so slowly and drop connection.
I saw in the logs of the router
[code]...
I have a computer next door with its own router and a computer in my house, how do i get it to go on 1 network, Both are wireless telkom routers.
View 1 Replies View Relatedi'm making up a new lab and need to create a simulated serial wan connection between 2 routers. I originally did it with 2 wic1t cards but i sold my old setup. I have access to wict1 cards i know they are serial connections. will it provide the same function as connecting with wic1t cards?
View 2 Replies View RelatedMy ISP provides IPv6 connectivity in the form of dual stack IPv4/IPv6 with DHCPv6 Prefix Delegation. Using a Cisco IOS-based router I managed to make such a connection by using as a template the Cisco IOS configuration file that my ISP has posted as an example in the following link:
[URL]
The main point on this configuration is a PPPoE connection with:
interface Dialer46
ipv6 address autoconfig default
ipv6 enable
[Code].....
configure this router according the Cisco IOS configuration file I linked on the top in order to have a working IPv6 connection?
Configuring a Cisco 1130 AP (autonomous) to a 1861 router.
I am struggling to work out how to connect this and get it working.
Router has 2 v lans, VOICE and DATA. All switch ports configured for access v lan (DATA) and voice v lan (VOICE)
We need the AP to have an SSID for VOICE and DATA and the gateway/DHCP server for each of these to be the router.