i'm making up a new lab and need to create a simulated serial wan connection between 2 routers. I originally did it with 2 wic1t cards but i sold my old setup. I have access to wict1 cards i know they are serial connections. will it provide the same function as connecting with wic1t cards?
View 2 RepliesIm able to create a gateway tunnel with two rv042 routers in different locations ( i can see the tunnel connected in the router) but the quick vpn utility is not working , i also tried to use the pptp as server as an alternative( im able to connect using windows connection to the pptp server but whenever I browse any of the four ip's allowed for the pptp server \10.0.0.200-204 it takes me to the documents of the local computer....I attached the configuration for one of the routers it is the same as the other end , just the information is flipped.
Message was edited by: Adrian Torres
I am trying to use f5d7230-4 v6000 to connect my TV and Playstation to my home WLAN, but cannot set up the router to receive the signal from the base station (FRITZ!Box). Is it possible at all to use f5d7230-4 v6000 for such function?
View 2 Replies View RelatedI have a Cisco 3725 running IOS 12.3. I have three WAN connections (2 x 100Mb and 1 x 2Mb serial) and I need to replace the 2Mb serial connection with a further 100Mb connection. However, I have not got any spare 100Mb sockets.My plan is to use a switch that supports VLANs, connect the three WAN connections to the switch, each in their own VLAN, then connect the switch to one port on the router, configuring the switch port as a trunk (so that it passes all three VLANs across the link) and configuring the router so that for that single Ethernet interface, it has three subinterfaces each configured for a VLAN that matches the VLAN used for the corresponding WAN connection.
I am a bit rusty on my IOS so I wanted to run this all past the community for feedback. [code] Any thoughts on whether or not that will work? Are there any commands from the original interface configurations that I CANNOT use when moving them to a subinterface? I'm thinking that the speed & duplex commands need to be removed?
I have 2801 and 2811 cisco routers. I need to setup a lab serial connections between the routers. Will WIC 2Ts work with the 28XX series routers ?
View 1 Replies View RelatedI have some 2620 routers and 2950 switches that have Console Ports that are serial. However my HP PC w.Win 7 dosent have any serial ports. I am looking for a USB to Serial converter that will allow me to access the console ports so I can configure these devices. I've read many old posts and still havent found a solution. Is it true that none of these cables work? Anything that will work on XP? (also have XP PC's).How about a RJ45 to Serial?? How about a PCI Serial card? I cant believe Cisco hasnt developed a conversion cable to use with their Console Cables?
View 4 Replies View RelatedI just bought this switch off Ebay and I can't seem to find anything online on the physical connection of this switch. It's not like normal switches where it just uses a ethernet type cable that goes to serial, it requires a female to female cable which does not exist anywhere so I ended up buying a gender changer for a normal cable I had but can't seem to get the prompt to come up. I'm using 9600, 8 data bits, no parity, 1 stop bits and no flow control. Do some wires have to be crossed a special way or something or do I need to type anything special in the console to get the prompt? I can't find much online on this switch. At least not as far as serial connectivity goes.
View 11 Replies View RelatedI am a total new comer for Cisco Router. All I know is plug the console cable to a serial port on a PC, fire-up HyperTerminal to view and that's it. I don't know any command or scripts.
I am trying to setup my client connection, I already receive the required configuration settings from ISP. It is a Leased Line Serial connection.
How to setup the router with the below configuration.
Serial IP : 1.X.XX.222
Serial Netmask : 255.255.255.XXX
LAN IP : 1.X.XXX.1 to 1.X.XXX.31
LAN Netmask : 255.255.255.XXX
[Code] ....
I have a 1905 series cisco router, when I run "sh int" command it gives me following details -
MTU 1500 bytes, BW 1544 Kbit/sec, DLY 20000 usec,
reliability 254/255, txload 7/255, rxload 151/255
Encapsulation PPP, LCP Open
Stopped: CDPCP
Open: IPCP, loopback not set
[code]....
let me know the significance of txload and rxload.This router is used for MPLS connectivity.Link is working OK..but I'm not able to understand exactly what is the above txload and rxload signify.There is also one peculiar phenomena occuring, when my reliability goes down then rxload also goes down or might be vise versa.
While I managed to connect to each router individually, I decided it was time to connect the routers together via serial; as I don't have any serial cables and need to buy some, what serial cables I need, as well as to ask whether I have the right cards in my router(s) that will allow me to do so.
I bought 3 1841 routers, and all have a 1 port serial WAN Interface Card (WIC 1-T); one router has 2 of these, and one router has a WIC-1B-S/T .. My question is, can I connect the routers with a serial cable via WIC 1-T, or do I need a 2-T
Have been battling a router connection to new ATT t1 connection. Router was configured and sent from sister company to this new location. We have had ATT tech test circuit and it tests good, had cat5 cable tested from ATT to router, it tests good. I continue to get serial up/ line protocol down status though and cant communicate to it from wan.
View 4 Replies View RelatedHow to create a new LAN Connection?
View 1 Replies View RelatedI got a pap for Xmas how do u create a connection in a psp
View 1 Replies View Relatedi'm trying to set up a simple VPN (client to Gateway), but i can't ! An SSL VPN or an IPSEC VPN, whatever..
The firmware of the RV042 is up to date, and i'm trying QuickVPN as a client vpn (also updated...)
My configuration details :
I'm in : 192.168.2.14 /24
My RV042 : 192.168.2.250 /24
And the VPN intend to connect me to : 192.168.4.x
[Code].....
I'm trying to setup this router with my IP range 192.168.100.1 to 192.168.101.254 but if I try to enter a subnet mask other than 255.255.255.0 I get the error - Invalid subnet mask. It should be 255 for given class of IP address at 255.255.xxx.0.
Every other device on my network allows that subnet mask, why not this router, it's stopping access from my 192.168.101.x devices.
I am trying to create a VPN between a SRP521W (only point-to-point VPN) and a UC560 (VPN server) and it seems it doesn't works (SRP doesn't create the tunnel).
View 4 Replies View RelatedI have a Cisco ASA 5505 and a Cisco/Linksys RV042. I would like to crerate a site to site VPN between them, and from what I've read it is possible. So I set up the connection on both routers but When I click on connect on the RV042 nothing happens. I've made sure that the encryption settings are the same on both routers but I can't get them to connect to each other. I think the problem may be with the RV042 as the ASA has other site to site VPN connections without any proble (although they are on other ASAs). I saw this thread [URL] but I'm not sure how to disable phase 2 on the RV042 or enable it on the ASA.
what setting I need to change on either router to make the site to site work?
Basically, I'm trying to create a VPN connection that I can use abroad so that I can use my own UK IP address in another country to access content such as BBC iPlayer and Skype which are restricted in the country that I am going to. I could buy a VPN but that would seem rather silly seeing as I could create my own, hopefully. However, I have tried to create a VPN but I have failed miserably! I tried setting up a VPN using the basic method, i.e. Create a new VPN, enter IP address, enter password etc, basically, I follwed these steps
[url]...
Basically, I'm trying to create a VPN connection that I can use overseas so that I can use my own UK IP address in another country to access content such as BBC iPlayer and Skype which are restricted in the country that I am going to. I could buy a VPN but that would seem rather silly seeing as I could create my own, hopefully. However, I have tried to create a VPN but I have failed miserably! I tried setting up a VPN using the basic method, i.e. Create a new VPN, enter IP address, enter password etc, basically, I follwed these steps
[url]...
Basically what I want to do is create a wireless network on my laptop so that my xbox 360 wireless can connect to it.What do I need to do to be able to connect my xbox 360 wireless to my Laptop? I'm not sure how to network bridge cause I'm using wireless to wireless also running windows XP Home Edition
View 4 Replies View RelatedGot two pc's, two routers and one switch, and two serial cables and I want to create a network.
View 4 Replies View RelatedI'm trying to connect two routers and create a subnet but failing due to a little knowledge but no real understanding! I've read the ultimate setup thread loads of times but can't get my setup to work.
Here's the setup I'm trying to build:
Internet -> Master ADSL modem/router (No NAT, no DHCP) -> Slave cable router (NAT, DHCP)
I want to connect 3 Xboxes to the master router with external IPs to avoid the whole "moderate/strict" NAT nightmare. Then I'll connect everything else (PCs, Macs, wireless devices etc) to the Slave router which will assign IP addresses and do the NAT thing. Both routers are Netgear N150s (master is ADSL, slave is Cable).
Here's what I've tried so far:
Master router:
All IP addresses supplied by ISP
Internet IP: xxx.68.160.143
DNS: xxx.xxx.3.xxx and xxx.xxx.6.xxx
Router IP: xxx.68.160.142
[Code].....
I have 3 WRV200 that I want to install in 3 cities.I want each router to have its own Internet connection from the local ISP.I then want each router to connect to the other 2 routers and create a 3 node WAN using VPN connections.
View 1 Replies View RelatedI have usb modem i want to set up WiFi in my home
View 1 Replies View Relatedi want to connect dvr to the internet i need the step to take and process of creating a public LAN Address
View 1 Replies View Relatedhow to create a password to access one pc to another pc .like i have 3 pc it is connecting throw switch .ip addresss is 192.168.1.1,192.168.1.2, 192.168.1.3 i want access from 192.168.1.1 to \192.168.1.2 like this here i want to create login password and how to remove password
View 1 Replies View Relatedwhat is the simplest way to create backup WAN connection?I have setup 2 WAN connection(2 ISP, 1 is DIA w/ fix ip, 2 is 3G), but if I enable both interface ,then I unplug WAN 1. no traffic goes to WAN 2.I have already have 3G connection enable all the time (w/ command "dialer persistent") Cisco 2811+ Cisco-HWIC-3G,
View 4 Replies View RelatedI have cisco router ASR 1006 .... i need to create PPPOE connection via Ethernet ... and can do that on the management port ???? and what is the type of adapter that use in the Giga Ethernt interface to connect it to fiber ???? hint :- my interface hardware SPA-10X1GE-V2
View 7 Replies View RelatedI am trying to create a bash script to log into routers and make config changes.I ran into a snag in that I am unable to pass a password for the ssh login.I tried tying an expect script to handle that piece but was unsuccessful.I saw on google something about public/private ssh keys (not the same type used to ssh into the box) but I do not want to go this route.Can this be done in another language other than a bash script?I would like to avoid TCL or EEM if possible, I want to learn a language that I can use for multiple purposes.
View 15 Replies View Relatedhow to create new unique self-signed certificate on RV120W? I can create request for singning by external CA, but I cannot create new unique self-signed certificate itself.
View 2 Replies View RelatedUnfortunately, it does not appear as if the SRP500 series will allow you to create an ipsec policy where the local or remote traffic selection is 0.0.0.0/0.0.0.0. It wants a specific network. I have a scenario where I want to send all traffic over the vpn tunnel.
Is there a workaround to this or a special way to input "ANY" as the remote network?
I am just wondering if it is possible to have two user accounts in Cisco RV042 V3 (Firmware: v4.1.1.01-sp (Dec 6 2011 20:03:18). User accounts to mean that one user can access the router with an administrative level access can do all the changes and management of the router's configurations and settings while another user can only do viewing of the system summary tab and connect and manage the simple configuration to connection to the ISP in both WANs, like setting up the connection type and release/renew the ip address for dynamic ip assigned by the ISP DHCP server.
View 1 Replies View RelatedI have a SRP547W that I have configured the following way:
LAN 192.168.15.1/24 VLAN1
LAN 10.10.10.1/24 VLAN10
LAN 10.10.2.1/24 VLAN100
PPPOE ADSL
Software DMZ going to 10.10.10.x and another to 10.10.2.x - this is working OK
I now want to use the Advanced Firewall features to block all ports except those that I need as the software DMZ forwards everything. When I try to create the rules I get "the values are invalid" message no matter what I try.
I want to create explicit allow rules, followed by a deny all rule for each of the IP addresses used for the software DMZ
Have I got the Subnet Mask Correct for the Destination IP? Or should it be 255.255.255.0? It doesnt make a difference either way
Policy DetailsNameValueSource IP Address0.0.0.0Source Subnet Mask0.0.0.0Destination IP Address10.10.10.xDestination Subnet Mask255.255.255.254ProtocolAnySource PortAnyDestination Port443ActionPermitScheduleEverydayTimes24 Hours