Cisco WAN :: 1905 / Clarification On Txload And Rxload On Serial Port For Routers
Sep 21, 2012
I have a 1905 series cisco router, when I run "sh int" command it gives me following details -
MTU 1500 bytes, BW 1544 Kbit/sec, DLY 20000 usec,
reliability 254/255, txload 7/255, rxload 151/255
Encapsulation PPP, LCP Open
Stopped: CDPCP
Open: IPCP, loopback not set
[code]....
let me know the significance of txload and rxload.This router is used for MPLS connectivity.Link is working OK..but I'm not able to understand exactly what is the above txload and rxload signify.There is also one peculiar phenomena occuring, when my reliability goes down then rxload also goes down or might be vise versa.
View 2 Replies
ADVERTISEMENT
Jan 22, 2012
2901 router that I just installed. I replaced a 1760 router with a new 2901 router and all seems to be working but for some reason the txload on interface g0/0 and interface multilink1 show 255/255 even though there is no traffic going over to this router. I have dual routers at this location and at the moment I have all traffic going over to my other router a 2821.
reliability 255/255, txload 255/255, rxload 1/255
View 7 Replies
View Related
Apr 11, 2006
How to know the serial0 or 1 (to v35 modem)was good or not ? is there any tool (software) or hardwire jumper to simulate loop back ?
View 4 Replies
View Related
Sep 5, 2012
We want to multicast several serial ports over the WAN/LAN network.In few words what we need to do is transport is several serial ports, is like a RS-485 network but in this case via IP.I do some similar to transport 4E&M lines with great results but I don't know how to start to do the same but with the Serial ports.
View 1 Replies
View Related
Mar 16, 2011
I just installed a HWIC-2T in a Cis co 3845 running IOS 15.1(3) T New build.The IOS self installed the port configuration including the command line "clock rate 2000000." I can edit everything but that entry using the CLI. When I enter the "no clock rate" it will not take in the running conf.
View 2 Replies
View Related
Apr 13, 2012
serial modem US robatics 5686G is not detected on windows server on serial port com1. i tried to restart the server . turn the modem on and off disable the com1 port reenable it again . update the firmware of modem on different workstation and connect it back to server ( couse it's working on another workstation so it's not the modem) i really don't know what to do is there a trick for this like in registry or somthing in mouse settings that mouse could actully detected on com1 and don't let the modem to show up on device manager? by the way modem cable is serial cable i tried to change the cable as well non of my ways works?
View 4 Replies
View Related
Apr 25, 2011
HP just released the 8560p elitebook- not a bad shake and it actually has an integrated Serial port.Any other notebooks that have integrated serial ports?- I know the T6x Thinkpads used to use a slimbay adapter thing. I just hate the Usb adapter, and bossman said I could get a new computer here pretty soon...
View 2 Replies
View Related
Jan 5, 2012
I need to connect to the console port on a cisco firewall, an rj-45 connector. The cable is a rj-45 at one end and a serial on the other. My PC has no serial port and I am unable to use the provided cable to connect to the firewall appliance. Is there software that can allow serial over my PC's Ethernet? I really don't have time to order a serial card for my PC.
View 1 Replies
View Related
Apr 23, 2012
Just want to ask if 4-port serial HWIC-4T is compatible for the Cisco 2801?We need additional HWIC for Fast Ethernet but the problem is we don't have already slot for it.We already have two HWIC-2T 2-port serial which is inserted at slot 1 and slot 3. We're planning to buy 4-port HWIC-4T so we can use the slot 3 for HWIC Fast Ethernet.if it's possible to have the 4-port serial HWIC-4T be inserted to Cisco 2801.
View 1 Replies
View Related
Jun 19, 2011
Is there a Port Adapter (PA) with Synchronous/Asynchronous Serial Ports, for Cisco 7200?
View 1 Replies
View Related
Feb 15, 2013
I have two 2950 Switches and am trying to connect via my laptop. My laptop doesn't have a serial port so I am trying to connect through the ethernet port, with a straight through cable and on the end as it goes into the console port I have bought a cisco console rollover adapter.When I turn on terra term I get nothing...just a black screen and it disconnects.
View 6 Replies
View Related
Aug 21, 2009
On the WAN port, there are 4 pins that are traced to the internal serial traces. Where can we get the cable that will fit into the WAN RJ-45 port and have a serial connector on the back end. It may be called a Cisco Debug Adapter, but we haven't been able to find?
View 9 Replies
View Related
May 15, 2013
I have a host machine (Laptop, Win 7 Home Premium x64) running Windows 7 Ultimate x64 on VMWare Workstation 9. I've got this system set up for UMDF driver development, because I need a target machine to debug drivers on. However, because I'm developing drivers for Win 7 (x86 and x64), I cannot connect to the virtual machine on via a simple network connection. Connection methods are outlined here.
I have tried a few different pieces of software (mostly Eltima software), and have Google'd every combination of phrases that I can think of. I can't find any information on this anywhere. I don't just need to share data between the machines, I need a more "physical" connection.
Does any know how to do this, or if there's another (preferably more simple) way of doing it?
View 1 Replies
View Related
Apr 12, 2012
i'm making up a new lab and need to create a simulated serial wan connection between 2 routers. I originally did it with 2 wic1t cards but i sold my old setup. I have access to wict1 cards i know they are serial connections. will it provide the same function as connecting with wic1t cards?
View 2 Replies
View Related
Mar 14, 2013
I have 2801 and 2811 cisco routers. I need to setup a lab serial connections between the routers. Will WIC 2Ts work with the 28XX series routers ?
View 1 Replies
View Related
Jun 26, 2012
I have some 2620 routers and 2950 switches that have Console Ports that are serial. However my HP PC w.Win 7 dosent have any serial ports. I am looking for a USB to Serial converter that will allow me to access the console ports so I can configure these devices. I've read many old posts and still havent found a solution. Is it true that none of these cables work? Anything that will work on XP? (also have XP PC's).How about a RJ45 to Serial?? How about a PCI Serial card? I cant believe Cisco hasnt developed a conversion cable to use with their Console Cables?
View 4 Replies
View Related
Oct 22, 2012
While I managed to connect to each router individually, I decided it was time to connect the routers together via serial; as I don't have any serial cables and need to buy some, what serial cables I need, as well as to ask whether I have the right cards in my router(s) that will allow me to do so.
I bought 3 1841 routers, and all have a 1 port serial WAN Interface Card (WIC 1-T); one router has 2 of these, and one router has a WIC-1B-S/T .. My question is, can I connect the routers with a serial cable via WIC 1-T, or do I need a 2-T
View 1 Replies
View Related
Dec 1, 2011
I have router 1905 which running IOS is C1900-UNIVERSALK9-M , how can I upgrade this IOS ?
View 5 Replies
View Related
May 2, 2013
Cisco view(patch 6.1.9) in lms 3.2.1 is not supporting router 1905.
View 11 Replies
View Related
Sep 21, 2011
My team has installed a 1905 series router at one of our offices. It has been connected through lease line to our servers at our head quarters. When we start internet access it slows down and subsequently it hangs. When we log into the router and start verifying its configuration it hangs after some time. We have replaced the router but the other router is also behaving in the same way. the possible areas and settings I should look into including lease line connectivity.
View 12 Replies
View Related
May 24, 2013
I have found recently that Cisco 1905 router is having a throughput of only 10 Mb. But the router is having 2 Gig ports!.My understanding is that throughput is the data packetforwarding done by a router at a time.
What is actually mean by throughput of a router. How the router can handle 1 Gb of data from interfaces at a time?
View 2 Replies
View Related
Mar 6, 2013
I have 3 WLC's currently running version 7.0.116 and a WCS on version 7.0.220. I am looking at upgrading the versions and am uncertain as to the compatibility.
1. Upgrade the WCS to 7.0.240, and upgrade the WLC's to 7.3. Resulting in my WCS just not able to manage the "new features" in the latest WLC code?
2. Upgrade the WLC's to 7.3 resulting in WCS completely unable to manage the WLC's? I am aware there is WLC 7.4 code however I've read there is an issue with 1142 AP's rebooting.
View 2 Replies
View Related
Aug 7, 2012
I want to know if Cisco Router 1905 is compatible for connecting USB Internet dongle for VPN Tunnel configuration at USB port of same router. If Yes then how to open that port for config. Find the show tech logs of Cisco Router 1905 attached.
View 1 Replies
View Related
Jan 25, 2012
What’s the maximum bandwidth (ADSL/internet) supported by ISR 800 series routers … particularly 891 security model.
View 23 Replies
View Related
Apr 10, 2013
Recently I came across a wireless design whcih I ws not able to understand.The design is:
1. Two wireless LAN Controllers 5508, each with 25 AP license. AP load (5APs per Contorller) shared between the WLCs and congured with Backup Controller option.
2. The design has a Data Center Switch 3560x series, on which the two WLCs, Cisco Prime Infrastructure and Cisco MSE were connected. I've attached the design here.
3. The Data Center Switch is configured with DHCP pool for the wireless clients. The IP Address of the Data Center Switch is : 10.xx.xx.2 and Default Gateway is: 10.xx.xx.1
4. On the WLC, the Management Interface is configured with the IP Address: 10.xx.xx.21 for Controller 1 adnd 10.xx.xx.22 for Controller 2. But, their DHCP Server is configured with IP Address: 10.xx.xx.1 but not with 10.xx.xx.2 .
This means, all the DHCP requests are pointing towards the Gateway of the Data Center Switch.Is this the correct configuration?I have seen the Wireless Clients getting the IPs allocated from the DHCP Pool, even though the Management Interface's DHCP server configured with Gateway IP address 10.xx.xx.1 .
The DHCP configuration for the Data Center Switch is:
ip dhcp pool xxxxxx
network 10.164.220.0 255.255.254.0
default-router 10.164.220.1
The Management Interface configuration on the WLC is:
Interface Configuration
Interface Name................................... management
MAC Address...................................... 2c:54:2d:72:b5:40
IP Address....................................... 10.164.220.21
IP Netmask....................................... 255.255.254.0
IP Gateway....................................... 10.164.220.1
External NAT IP State............................ Disabled
[code]....
View 2 Replies
View Related
Jan 28, 2013
Basically I need to upgrade the license for Base-AP count to add 100 more AP's however my vendor has provided hardcopy of license as below:
-LIC-CT5508-UPG
-AIR-CAS-3KC-K9
-AIR-WIPS-AP-5
-L-NCS-1.0-100-ADD
My understanding is rigister LIC-CT5508-UPG/PAK number on cisco site and get .lic file however what is the use of other PAK where do i register this files with? Moreover , we do have NCS , MSE in place which is centralised devices.
View 2 Replies
View Related
May 19, 2013
I currently have a 3560G switch running c3560-ipservicesk9-mz.122-58.SE2 I have a spare 3560 V2 switch I want to configure and have ready in case of a failure. This spare switch is running c3560-ipbasek9-mz.122-55.SE5 My plan was to pull the IOS image from the current switch and upload it to the spare that way I have an "idnetical" switch. From what I have read, there are some feature differences between "ipbase" and "ipservices". However, when I run the show license command on the production switch, I get an unrecongnized command error. So that throws into my confusion as if its running an ipservices image, shouldn't it have a license file?
View 4 Replies
View Related
Mar 28, 2012
we are observing the no. of conn thru asa 5580 is getting increased and one a fine day it will stop sending/receiving traffics.firewall# show conn count 1900000 in use, 2000008 most used As per the datasheet of this asa, the max conns permissible is 2 million (20 lacs). and the output shows that currently 1900000 connections are there and 2million+8 connections are most used.when i run " show local-host | include host|count/limit ", below are the outputs showing for max connections..
local host: <172.x.x.x>,
TCP flow count/limit = 35857/unlimited
TCP embryonic count to host = 25
UDP flow count/limit = 0/unlimited
local host: <DC01>, TCP flow count/limit = 306/unlimited TCP embryonic count to host = 8 UDP flow count/limit = 736807/unlimited
local host: <DC02>, TCP flow count/limit = 246/unlimited TCP embryonic count to host = 2 UDP flow count/limit = 582010/unlimited
local host: <172.y.y.y>, TCP flow count/limit = 1/unlimited TCP embryonic count to host = 0 UDP flow count/limit = 308412/unlimited
These are the top 4 connections, i wonder should we consider only the tcp flow count or udp as well ?
View 4 Replies
View Related
Apr 15, 2013
As a matter of fact i am new to this field .I have cisco 1700 series router which has ea0 and FE 0 port
E0 connected to LAN and FA0 for ISP ,both are configured wit publisc ip.and ststic route to ISP. (E0 connected to switch and fa0 connected to ISP MUX)
When i issued sho arp command i have received more than 30 entries of MAC and IP address . I am wondering how i received this much mac in arp table.
View 5 Replies
View Related
Jul 12, 2010
We want to configure the "mac-address-table synchronize" command on our 6500 series switches to ensure that the CAM tables on our DFCs are in synch with the PFC on the supervisor modules. url...it is recommended that we disable the routed MAC purging with the mac-address-table aging-time 0 routed-mac global configuration command. What is a routed mac entry? Are there any issues with running that mac aging-time command?
We also plan to run this command "mac-address-table aging-time 14400" to keep our ARP and CAM tables on the same aging time to reduce unicast flooding on our network. Can we run this command with the "routed-mac" command above?
View 2 Replies
View Related
Dec 28, 2011
you can configure a cisco 1905 router with vpn ipsec site-to-site in an aggressive mode? If so, any link to what I do? The VPN works well, but on site A, I had to configure a crypto map associating the IP address for site B (wich is dynamic), so if the connection on site B broken, I will have to configure another crypto map.
The scenario is:
Site A - ASA 5510 configured as a VPN concentrator and firewall for enterprise.
Site B - Cisco 1905 connected to Internet through a ADSL through a dynamic IP address and starting connection to Site A, bellow is the configuration:
crypto isakmp policy 10
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp key xxxxxxxxxxxx address W.X.Y.Z
[code]....
View 2 Replies
View Related
Apr 22, 2013
how to: port forwarding to 2 different destinations based on incoming WAN port
The default HTTP service works fine: TCP80/80-> 192.168.0.55
I have a couple of IP security camera's I'd like to be able to access remotely that also listen on port 80. I tried TCP & UDP 8009/8009-> 192.168.0.9 without any luck. Not sure how to handle the port redirects on the RV042G? Seems simple and was on the Symantec, could be user training :-)
I was able to do port redirect with the Symantec Firewall I'm replacing.
View 2 Replies
View Related
Oct 11, 2012
Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23 ?
First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80
View 2 Replies
View Related
