Cisco srp521w router vpn configuration. company has wan static ip to router. enable vpn Cisco server in router. connected with Cisco vpn client. route failed in log. Need to access a PC on the company site with address 192.168.15.105 and router with gateway 192.168.15.1.
How do i configure ip pool ? different ip address? if i connect how do i access pc 192,168.15,105 ? remote pc with 192.168.1.100.
Any recommendation for creating a configuration template for the SRP521W? I can use the Admin-->Backup Config to get a xxx.cfg file, but I cannot edit it with notepad++. Also, i know the config can be view via view-source: [URL], but how would I load a modified copy of this back to the router?
View 8 Replies View RelatedWe've come across an issue whereby the WAN port fails to light up with an Adtran Total Access 832 (via bonded SHDSL) unit.
Eventually the WAN port does light up after connecting and disconnecting it several times with the ethernet cable. However as a test I power cycled the router with the WAN cable disconnected and had a strange issue where the WAN light would constantly flash and show up in the web gui as being connected when in fact the Adtran Unit showed the device was not connected at all.
This is the second Cisco SRP521W router in place as the original one disconnects overnight without any load and a power cycle would fix the issue, but this replacement router disconnects during business hours (even worse for the customer) and power cycling does not bring it back online. We've adjusted the WAN port to 10MB Full on both devices and hope that it stays up. I am wondering if any has had a similar experience? Would this be a behaviour of a faulty unit or may it not be compatible with the Adtran Total Access 832 (via bonded SHDSL) unit perhaps?
I have a problem in connecting SRP521w with CCA v3.2. I tried to connect the device with CCA but it said that that the device is unsupported. I already upgraded the router's firmware with v1.01.26.
Here is what the CCA looks like every time I try to connect with the router :
I have a router SRP521W I wonder if you can setup a self-attendant or ivr to this device.
View 4 Replies View RelatedIs it possible to send all traffic through site to site VPN using SRP521W (on the other site ASA) ? Lets say, traffic to Internet from branch through HQ - site to site VPN between branch and HQ. I've tried to set up destination crypto policy entry to 0.0.0.0 0.0.0.0 but it's not accepted. Firmware version is 1.01.26 (003)
View 4 Replies View RelatedHave followed the admin guide, and can setup this up fine, however what we're wanting is to turn off any IP connection for the main wan ethernet interface and only have the sub-interface have an IP connection method.
I can't see how you can turn this off, which is causing a double-up of dhcp requests being sent when using both the main/sub ethernet interfaces to use dhcp.
This has been tested on the 521w and 521w-u versions, and I've just used the latest firmware 1.2.4 on the u version.
How can this be configured so that there is only 1 WAN interface that is using IP (the sub interface) Setting default routes to point to the sub interface doesn't make a difference.
I am trying to create a VPN between a SRP521W (only point-to-point VPN) and a UC560 (VPN server) and it seems it doesn't works (SRP doesn't create the tunnel).
View 4 Replies View RelatedWe have been using a SRP521W as the main Router for an office with about 25 users.
So on the cable network it's about 25 computers, 25 IP Phones, 3 printers. Wireless network hold some smartphones and tablets. Computer traffic is 100% Remote Desktop.
That said, for the last few days network connectivity sucks. I think the problem is, precisely, the SRP521W. Some mornings the WAN link is down and can only be brought up by a router reboot.
There's an IPSec tunnel to HQ.
Wireless network was moved recently to a WAP121 to offload the SRP521W. It has two networks: internal and customers with two VLANs.
CPU Usage is around 30-45% all day and spikes to 100% sometimes. RAM Usage is 40-45%. I do not know if this is "too much", "average" or "really low load".
Anyway, time for questions:
a) How can I get a table of active connections on the firewall/NAT to see if there anything "strange" on the network traffic that maybe causing issues?
b) Is there any know bug in the VLAN handling of the SRP that maybe causing the issue? (it's one of the latests changes introduced).
c) If the problem is that there's too much load for such a small router, what replacement would you recommend given the details above? (remember I do not really need wireless on the router as I have the wap121).
I have one SRP521W-K9-G1 and need to provide guest internet access without access to my network. What is the best way to configure this?
View 3 Replies View RelatedJust brought another set of SRP521W, after changed the WAN setting to PPPOE, we unable to access the web management. The power/sys light will keep blink when trying to access the web management. We able to ping it. We tried the reset button but it did not work as well. Is that a way to upgrade the firmware without using the web management?
View 4 Replies View Relatedi cannot access the web managemnet interface of this router from a different subnet.THe WAN interface is a 4G LTE connection,I have disabled both the SPI firewall and NAT and enabled remote management from any ip address but i cannot access the admin web page from a remote subnet.Doing a port scan of the routers WAN or LAN address i cannot see any ports open at all...its as if firewall or NAT is still enabled somehow.
View 0 Replies View RelatedUsing a 3G USB Modem (Huwaei E153) the mobile network status is connected however the Wan Interface (AutoConfiguration -DHCP) is displayed as Disconnected (Physical layer disconnected).
View 2 Replies View RelatedAs you can see i have problems with connecting 2 SRP521W together for an VPN tunnel. I tried as much as I can but now i dont know what to do or how and where is the mistake? the connection between these two devices was there last week, after weekend (nothing changed in configs) the connection suddenly was interrupted, without any reason or warning. another day it worked again and 20 mins later connection was dead again...and now it wont establish at all.. here are some screenshots from the vpnconfigs of my devices. one has a static IP the otherone uses FQDN. These are the IKE policies: Here the IPsec Policies: and the GRE policies:
View 10 Replies View RelatedWe recently switched from a ADSL2+ service to a 2Mb SHDSL link. Uploading images to our website is happening all day long, thus greater upstream bandwidth was required.
Our downloads are suffering somewhat, the upstream gets easily flooded and downloads start to trickle.
I have a SRP521W which has a few QoS options. The QoS Bandwidth control has upstream bandwidth set to 2048 Kbps. Now I don't know how to enforce anything. How to use the WAN strict high priority queue appriopirately.
The website has a static IP address, so I can target that in the rules to only use 80% of the bandwidth?Alternatively can I limit upstream traffic per user?
i was planed to make a vpn over rv042 so i get the rv042 connected behind a thosmon 456(configured as a bridge) and 1 static ip ... and i configured the vpn and worked great ...but due to some circumstance i get a package of 6 ips insted of the old ip , so when i try to configure the router with the ISP they but the wan ip 10.232.x.x and told me that an internal ip from there lan ... and give me the 6 ip of 196.x.x.x to use as 1 for internal interface for the rv042 and 5 for the pc's,now the vpn not working anymore...notice: when try to configure the vpn tunnle in the local securty setting i mark the ip only and the ip that abear is the wan ip 10.232.x.x but i can't ping that ip beside i can ping the internal ip of the router 196.x.x.50does rv042 can support static and virtual ip inside the lan |! can i configure the thomson as pppoe and use one static ip from 196.x.x.x as wan ip for it ... and use anther 196.x.x.x ip for the rv042 to get access from outside and connect the lan to the rv042 with internal ip 192.168.x.x ...so i can access the vpn from outside .....and can connect the device i need to use static ip to the thomson ...
View 0 Replies View RelatedI am looking to configure RV042 for VPN access to local machines and Win 2008 server. The story: Had issues with remote printers being created for clients logging into old Linksys RV042 with Linksys VPN software. First Tech exposed server without security, and it had to be removed as it was being attacked, but did not fix printing issue. 2nd tech could not get VPN to work after 1st tech. 3rd tech, 4hours, and I got that the router is a piece of ... So I'm out over 1000, and not able to have a simple router set up. The present situation. New RV042 with firmware V4.1.1.01, using Cisco VPN client 5.0.07.0410, most XP 32 bit machines coming into network, one 64 bit win 7. My clients have been unable to access their data for too long.
View 3 Replies View RelatedI am struggling to configure my new RV180w router to accept a VPN connection from my Apple computers.
I wish to use IPSec with Group and Pre-Shared Key authentication. The RV180 has just replaced my 800 series ADSL router and I want my remote clients to be able to connect using either the VPN client capability built into the OS X operating system or the Cisco VPN Client software installed on their Macs.
So far, using the RV180's web setup screens, I have created a VPN Policy and a corresponding IKE Policy was created as well. I couldn't see anywhere to include the 'Group' name. I have created a user but wasn't sure of which Protocol to use so I am trying XAUTH.
At the client end some people are connecting using Cisco's VPN Client software Download Software - Cisco Systems
Some people, with OS X 10.6 and above, are using the Mac OS X network built-in VPN client.
We all connected without a problem to the previous 800 series router using IPSec with Group authentication and Pre-Shared key.
I'm trying to setup a VPN tunnel between a Cisco RVS4000 on our side and a Cisco ASA5520, to connect a machine on our local network to a test server on the target side.
We have all the settings setup correctly and the tunnel is up and running, however, our local machine can't connect/ping to their server. I've tried a trace route both from the machine and from the RVS4000 itself, and they both get stuck after getting past 192.168.1.1. Is there any routing or NAT-ing that I need to do on our router? Or is there a problem somewhere else?
I am trying to split traffic entering from the web for servers so everything goes over the ADSL link but time sensitive information such as Sharepoint (TCP80) go direct over the ESHDSL link, now the problem is traffic that enters through the ESHDSL hits the server, the server replies out of its default gateway which is the ADSL which doesnt know what to do since it does not have a NAT entry for its return path.
How can I make it so traffic can enter one router and exit the other?
The two routers have HSRP to provide fail over between the two, and BGP is setup so one BGP route goes ESHDSL-ADSL and the other ADSL-ESHDSL
The routers are a 877M-SEC-K9 and a 881-SEC-K9
I have just purchased the RV042 and while it is working great on WAN1 over Xfinity/Comcast broadband, I'm unable to get it working with my AT&T DSL for WAN2. I am planning on running this in failover mode - not load balancing.
The DSL modem it is connected to is a SpeedStream (hooking up laptop directly works etc. etc.). The SpeedStream is set to PPOE authentication passed in via the computer (in this case the RV042). On the RV042 side, I set it to use PPOE, using the credentials as given my AT&T DSL. The DNS servers are set to the ones recommended
We have a customer who has a network consisting of two ISPs, one as a primary and the other as a backup. The customer would like us to use HSRP for the failover. The problem is the customer wants the configuration done with the two ISP routers connected to a 3550. He is under the impression that it can be done this way. ISP 1 []--------[_]3550------[] ISP2. From my understanding of HSRP can only be done with Cisco router and not ISP routers.
View 3 Replies View RelatedI am unable to get any configuration parameters to work on my SRP547 for VOIP. ADSL2 works fine. Equipment replaces a ya.com (Arcadyan ARV4518PW) which worked ine albeit with significantly less features. Problems encountered due to the lack of equivalents for some parameters and an overabundance in the new unit which simply don't exist in the Arcadyan product.
View 7 Replies View RelatedI have a problem with new WRVS4400N router.after connected it to my infrastructure modem and configured its WAN configuration with my ISP supplier, ISP see that I'm connected, I see that I'm connected, get an EXCELLENT link and about 70M link speed.Yet no able to access the web when trying to do so from a different devices ( TABLET, LAPTOP) or different connections ( WiFi , Ethernet cable).when I'm connected directly to my infrastructure modem, access to web is successful.in addition, when previous router ( EDIMAX ) that was connected also and tried, access to web was successful.
View 9 Replies View RelatedI have an old RV082 that I suppose has failed. The red diag light on the front panel is lit and nothing works. I've already replaced the unit, so I don't really need to fix it. Here's my issue: the setup on the old unit was pretty complex with a number of port forwards and other non-default settings. I'd like to recreate those items on my new router, but they were never written down so I don't know what they were. I've tried to connect a computer to one of the LAN ports, but they're all dead. Is there any way to get at the configuration page?
View 2 Replies View RelatedYesterday I have purchased a new rv042 router, If i enter url...I have access to a menu but nothing is shown when I follow the menu link.
View 6 Replies View RelatedI am setting up a SBS 2011 Essentials sever using a rv082 router. I have a decent understanding of how everything is suppose to work, but execution has been sloppy. My aim is to set up a central storage location, back up services, remote access and VPN. Yesterday I had set up dhcp and dns roles on the sever, configed port forwarding and firewall setting on the router, at that point I was just bouncing around everywhere trying to get stuff to work, clearly not the best way I know. Before I left I reinstalled sbs for a couple of reason, along with resetting the router to default.
View 1 Replies View Relatedwe're planning a small private network for our holiday appartments. Therefore we get a Cisco Small Buisiness Switch SG200-18 from a friend. We have created 6 diffrent VLANs on it. But it seems that we need a router do to the routing of our cable connection to the WAN. Is it possible to connect the WRVS4400N to that switch and configure multiple subnets for that vlans? Or how can i do that? I have add a drawing for better understanding.
View 3 Replies View RelatedI have an SRP541W with two ADSL modems attached to it. Both are running bridged mode with PPPoE connections to two different ISPs, (TPG and Telstra Business Direct). The TPG connection is far cheaper, and has a much higher download limit. Sadly, if I leave the router in "load Balance" mode for the WAN, it "prefers" the Tesltra connection because it's faster. I want downloads for movies/music, Youtube, Internet Radio, etc, to go through the TPG connection. Is it possible to do this in the router, or would I need to set up a proxy server, (or some other external device/application)?
View 5 Replies View RelatedI am not having much success setting up a IPSec VPN tunnel between a RV042 V3 running v4.0.0.07 firmware and PIX 525 running 8.0(4) code.
Let's say the configuration looks like this:
The RV042 has public IP 70.0.0.1 and private LAN IP 192.168.1.1 /24 The PIX has outside IP 69.0.0.1 and inside LAN IP 172.16.0.1 /24 The RV042 is running as DHCP server on it's private LAN A Windows server at 172.16.0.2 is the DHCP server on the PIX's inside LAN.
I've tried every option on the RV042 for Phase 1 and Phase 2, but I am not certain how to configure the Advanced features especially Aggressive Mode, Compress, Keep-Alive, AH Hash Algorithm and Dead Peer Detection.
On the PIX I've tried the basic setup through ADSM, but it's not as clear or obvious to configure both sides with compatible settings compared to setting up a tunnel between two RV042s.
I just set up a new RV180 router in a SOHO environment. A couple questions regarding the configuration possibilities:
1) Is there any way to deny static IP LAN traffic and force all clients to DHCP? It seems the RV180 is very "IP range" based, so I'm dividing user privileges based on IP grouping. It would be simple for a user to circumvent this by simply assigning a static IP address in a range that has higher access.
2) Is the Access Rules table a "first match" or "last action" type of table? Meaning... "first match": the first rule that matches all conditions is hit and the rest of the table is ignored. "last action": the last rule that matches all conditions to modify the traffic is what is used.
The reason I ask this is I want to ban all outbound traffic from a range of IP except a handful of services, and there are multiple layers of internal IP ranges that will be allowed different levels of outbound access.
I've goggled and searched here, and I can't seem to find what I'm looking for. I need to make a couple changes to a clients Cisco 800 series router, enable ping replies add ip addresses to the ssh ACL.I can't seem to find any basic commands for CLI anywhere.
View 2 Replies View RelatedI just installed a new RV 120W to replace my dlink router.The problem is i cant display the configuration site (192.168.1.1). My internet is working fine and when i go to 192.168.1.1 i can logon (with the password i set using the installation disk) but then i see the top of the config site (blue) but where the config panel should be i see `site cannot be displayed`.
View 4 Replies View Related
