Routers / Switches :: Error About IP Equals Subnet

Apr 18, 2012

Following instructions on How to add a 2nd router to network.This error will not let me complete and save the definition. Changed 2nd router IP address to 192.168.1.2 static, disabled DHCP, added 1st router IP as default gateway, set subnet mask to same as 1st router. Problem occurs in next frame called 'Network Setup' it is requiring a 'router IP' & subnet mask again and will not accept either the 1st or 2nd router IP address - gives the "IP equals subnet please correct" error or "LAN & WAN IP addresses are identical.

View 11 Replies


ADVERTISEMENT

Cisco Routers :: RV110W - Error / Destination LAN IP Cannot Be Same As Router IP Subnet

Oct 11, 2012

In Cisco RV110W I configured 2 VLANs, one 192.168.1.xxx(Green Net) and the second 192.168.2.xxx with only one fixed address 192.168.2.100(Server), which is configured in the DMZ Zone. I enabled in Cisco "inter-VLAN-Routing", that is described "routing between the seperate VLANs on the Cisco RV110W" I can Ping the server in one direktion, in the other I got an error. That is all expected and ok! All other expected abilities work well !Now I want to see the server from green net . (firewall in the server is off)I configured Networking/Router with exact the Hint values and got an error : "destination LAN IP cannot be the same as the router IP subnet"

View 5 Replies View Related

Routers / Switches :: What Is Subnet Mask Of 10.2.1.3/22

May 8, 2011

what is subnet mask of 10.2.1.3/22

View 1 Replies View Related

Routers / Switches :: 2 Routers On Same Subnet With DD-WRT VPN Tunnel On Second?

Mar 13, 2012

How to set up a home network with 2 routers, where R1 acts as the DHCP server and R2 is basically a switch, connected LAN to LAN and everything is on the same subnet. Currently I have a different setup:Both routers have the DHCP server enabled and I connect R2's WAN port to R1 LAN. Therefore I have 2 subnets. Now my special requirement is that R2 is a DD-WRT router, which establishes a VPN connection to StrongVPN, so that all internet traffic via R2 is encrypted and goes through the StrongVPN server. Now my question:If I change my router setup to the same subnet, meaning R2 connects LAN to R1 LAN and I disable DHCP server on R2, will R2 still be able to establish the VPN connection?

View 5 Replies View Related

Routers / Switches :: How To Subnet A Class B IP Address

Jan 16, 2011

how to subnet a class B IP address?I have a homework, I don't know how to subnet a class B.

View 2 Replies View Related

Routers / Switches :: Routing Between Two Networks With Same Subnet?

Mar 7, 2012

Two networks. NetA: IP subnetID 10.101.x.x subnet 255.255.0.0. Devices have static-assigned IP's. Only DHCP runs on wireless AP for wireless client connection. IP addressing scheme set by hardware vendor, so not under my control. NetB: IP subnet 10.x.x.x subnet 255.0.0.0. Campus LAN and also not under my control. DHCP supplied addressing. how to get NetA devices to route to NetB?I would like to be able to provide Internet access (via NetB)to NetA devices.

View 7 Replies View Related

Routers / Switches :: Routing Traffic Across Nics From One Subnet To Another?

Sep 25, 2012

I have an issue with some traffic routing:

Machine A | Machine B (Win 2008 R2) | Machine C

Start: 192.168.5.9 > 192.168.5.5 (NIC 1) - 10.14.137.130 (NIC 2) > 10.14.137.128So the question is how do i get traffic from Machine A to Machine C. I've tried various 'Route ADD' cmds but no luck so far. So was hoping someone out there could shed some light for me?Machine B is a AD/DNS and can talk to the entire 10.14.137.x range but has no forwarders set up in DNS. And does not act as a AD/DNS server for the 10.14.137.x range. It fills these roles only for the 192.1668.5.x range.

View 3 Replies View Related

Routers / Switches :: Network Subnet Range To Wide For Vpn?

Jun 23, 2011

I have a supplier which i need to connect a site to site ipsec vpn connection to (from a draytek router). I have already done this on our main site with no problems using the local ip details of 192.168.1.0 and subnet 255.255.255.0 however i need to do the same on our DR site which uses the ip details of 10.1.0.0 and subnet of 255.255.0.0. Our supplier told me the 255.255.0.0 is already used at there end by a different customer so we are unable to connect the vpn and communicate (in theroy we can connect but our supplier cannot reply). We can setup a connection to another spare server on a different address using a different subnet but effectivly this would mean that communication would stop at that server and communcation to the overall network or specific server the supplier needs access to (on the 10.1.0.0 255.255.0.0 network) is not possible. I was thinking maybe an internal vpn server to server connection through win server may do it, 2 nic cards or routes in the server routing table but this all seems a bit messy. Our network consits of win 2003 and 2008 R2 servers and is basic network with modem-vpnfirewall-switch and devices on the internal network connecting to the switch.

View 5 Replies View Related

Routers / Switches :: Communication Administratively Filtered Error?

Aug 9, 2012

I have 2 different network topology - network A and network B Both of them are connecting to the same gateway (a firewall) to the net. they're using the same range of public IP pool to NAT the private IPs. in shorts, all setup is almost the same except the devices' brand between A and B.I have no problem to access the webpage using network A. But whenever I attach the same laptop to network B, the same page won't display at all.I've done wiresharking to network B and the result shows "ICMP destination unreacheable (Communication administratively filtered)" which reported by unknown device (suspected to be the webpage's gateway).

View 5 Replies View Related

Routers / Switches :: Belkin Router Installation CD Unknown Error 5?

Oct 3, 2011

I have a dell Win XP need to connect to Belkin router

View 1 Replies View Related

Routers / Switches :: Tplink Set Up Error - Failed To Verify Router Settings

Dec 18, 2011

I've been trying to set up my TP-Link WR740N router but it always give the error "Failed to Verify router settings" on the last step of the set up screen. Broadband: Globe broadband (Wired)Modem: Siemen Gigaset SE260 I'm also confused on the 2nd Set up screen, it gives the option to select Dynamic IP Static IP PPoEI've tried using the Dynamic IP and PPoE but still getting the same error message

View 1 Replies View Related

Connecting Router Equals No Internet Browsing

Jan 1, 2013

Every time I connect my router, I can't use the internet browsers. But I can see there's a internet connection. Bu once in a while even with just a modem connected to my computer I can't use the browsers. The signal from the router to my Xbox 360 works but sometimes it says there's DNS Error or IP Address Error causing my Nat to be strict. Once in a while, I can access my router's page when it's connected. [code]

View 19 Replies View Related

Routers / Switches :: Connect Two Systems Together But Was Giving Error That Contact Network Administrator

Jan 30, 2012

Trying to connect two systems together but was giving error that contact network administrator,one system is laptop with wireless and other is desktop but connect through cable but running windows XPSamson

View 1 Replies View Related

Routers / Switches :: Linksys WRT160Nv3 Network Error - Unable To Look Up Host Names

May 12, 2012

I am able to connect to corporate VPN with no issues when connecting directly to ISP modem. When I try to complete the same VPN connection via a Wireless Router (Linksys WRT160Nv3) i get the following message: "Network error. Unable to look up host names"I have tried connecting and it will initially connect, but 15-30 seconds it will drop and connection can't be re-established.Is there a setting on the Linksys WRT160Nv3 that needs to be changed?

View 3 Replies View Related

Cisco Switching/Routing :: WLC 5508 - Error From Same Subnet

Jul 16, 2012

Getting a lot of the following errors on our 5508 form the same subnet: 10.20.0.1 255.255.248.0 . I tried researching and not getting much.
 
broffu_SocketReceive: Jul 17 10:11:10.068: %DATAPLANE-3-DP_MSG: broffu_fp_dapi_cmd.c:2891 FP0.09:(7089389)[cmdAddIpv4:2921]failed to find ipv4 10.20.6.58
[code]....

View 2 Replies View Related

Cisco :: Same Subnet Error - Configuring Hosts To Router Ports

Jul 30, 2011

If all you have is a high end cisco router available, can you plug in hosts to the router ports, and configure them within the same subnet? (When I try to configure ports within the same subnet, I receive a "same subnet" error.

View 3 Replies View Related

Cisco Switches :: SG300 Not Reachable Beyond Subnet?

Feb 6, 2013

I'm trying to configure a SG300 to be reachable beyond its own subnet. Its IP address is configured by DHCP to 192.168.2.2/255.255.255.0. It is possible to ping the switch from the same subnet but not from outside. The switch is set to layer 2 mode. All routing should be done by the gateway.
 
Here's what I have checked so far: The default gateway and netmask are set correctlyThe gateway can ping the switchHosts in the 192.168.2.0/24 subnet have connectivity to other networks through the gateway (i.e. gateway configured correctly)Administrative interface > IPv4 interface shows the correct ip address, netmask, and gateway (greyed out because it is assigned by DHCP)the switch can ping other hosts within the same network  
 
Is there some kind of firewall setting that prohibits the switch to respond to ip packets from outside the subnet?

View 5 Replies View Related

Cisco Switches :: SGE2010p / Configure Vlan To Reach Few Subnet?

Jun 9, 2010

Just got a new SGE2010P layer 3 switch. I'm trying to configure Vlan to reach a few subnet. I have the original 192.168.1.0/24 as vlan1. I want to reach our WiFi subnet 192.168.10.0/24. The WIFI router is directly connected.  It's new for me as the previous Job i was sorking with a ws-3750-48.
 
i did from console  change my switch to layer 3 mode... ( i want it as the DGW for each Vlan)from the web interface, i create a vlan4 for our WIFI Next i go to ipv4 to add an IP address to vlan 4 like 192.168.10.254 /24 As soon as I apply the IP the switch stop responding, Ping request time out..  i need to reboot the switch..

View 2 Replies View Related

Cisco Switches :: SG300-28P - How To Enable NetBIOS Packet Forwarding Between Subnet

Oct 11, 2011

I recently purchased an SG300-28P.  I have 2 VLANS/subnets that are successfully routing between them.Machines on both sides can ping each other just fine, but none of the usual Windows/NetBIOS browsing is possible.  I've recently learned that NetBIOS is not usually forwarded between subnets.  How would I enable NetBIOS packet forwarding between my subnets?
 
Reading the manual, it seems like enabling UDP Relay might be the answer but I've been unable to get it to work (same with DHCP relay). 

View 8 Replies View Related

Getting Printer To Print On Different Subnet With No Routers?

Jun 29, 2012

I need to print to a printer in with a static IP on a different subnet from a host on a different subnet using DHCP.

View 1 Replies View Related

How To Connect 2 Routers LAN - WAN And Create Subnet

Sep 8, 2012

I'm trying to connect two routers and create a subnet but failing due to a little knowledge but no real understanding! I've read the ultimate setup thread loads of times but can't get my setup to work.

Here's the setup I'm trying to build:

Internet -> Master ADSL modem/router (No NAT, no DHCP) -> Slave cable router (NAT, DHCP)

I want to connect 3 Xboxes to the master router with external IPs to avoid the whole "moderate/strict" NAT nightmare. Then I'll connect everything else (PCs, Macs, wireless devices etc) to the Slave router which will assign IP addresses and do the NAT thing. Both routers are Netgear N150s (master is ADSL, slave is Cable).

Here's what I've tried so far:

Master router:

All IP addresses supplied by ISP
Internet IP: xxx.68.160.143
DNS: xxx.xxx.3.xxx and xxx.xxx.6.xxx
Router IP: xxx.68.160.142

[Code].....

View 1 Replies View Related

Cisco Routers :: Set Up 2 Subnet With Two RV042?

Apr 30, 2012

I'm trying to set up 2 subnet with two RV042 routers. One router will  act as a gateway and both WAN ports will be used by two different isp  connection. The first router (gateway) LAN IP will be 192.168.0.1/24. I  would also like to set up another router behind the gateway with with  separate subnet 192.168.1.X/24. And I would like clients on the  192.168.1.x subnet to use the internet through the gateway router and  clients on the 192.168.0.x subnet to access resources on the 192.168.1.x  subnet. Am I able to do this with two RV042?

View 6 Replies View Related

Cisco Routers :: RV082 LAN Subnet Mask

Nov 12, 2012

I would like to set the subnet mask off the lan to 255.255.240.0 but the selection menu do not allow to do it.

View 8 Replies View Related

Cisco Routers :: RV220W Can't Create 255.255.254.0 Subnet

Nov 8, 2012

I'm trying to setup this router with my IP range 192.168.100.1 to 192.168.101.254 but if I try to enter a subnet mask other than 255.255.255.0 I get the error - Invalid subnet mask. It should be 255 for given class of IP address at 255.255.xxx.0.
 
Every other device on my network allows that subnet mask, why not this router, it's stopping access from my 192.168.101.x devices.

View 5 Replies View Related

Cisco Routers :: How To Make Subnet With RV042

Jul 10, 2012

I have RV042 Router, I'm using only one Internet conection, I'm using IP group like this 192.168.95.x, my DHCP setting use 192.168.95.120 to 192.168.95.240, but in this time I have 245 workstations (may be I will have 25 additionals workstations) and some times I see IP conflict message in my current work stations.
 
I had read about SUBNET like response about my problem, but I'm not sure about that and how to make subnet with my RV042.

View 7 Replies View Related

Cisco Routers :: SRP527W - Can Use For Routing Subnet Other Than NAT

Feb 12, 2012

I'm wanting to use the SRP527W (from Telstra) to route a block of assigned internet addresses (/29) over the WAN internet IP address. Is this possible on the 527W, or does it only do NAT routing?

View 6 Replies View Related

Cisco Routers :: RV042 Traffic From One VPN Subnet To Another

Dec 2, 2012

We connected to locations to the RV042 by setting up 2 Gateway - to - Gateway VPNs - both locations can communicate with the RV042 and devices within the local LAN of the RV042 - however at the moment it is not possible to send traffic from 1st VPN Location to the 2nd VPN location

View 1 Replies View Related

Cisco Routers :: RV042 Multiple Subnet DNS?

Aug 24, 2011

I have a RV042 with multiple subnet, 192.168.10.0 and 192.168.9.0. 192.168.10.0 is assigned to the LAN, 192.168.9.0 is created under multiple subnet. Both subnet can access Internet by accessing IP address, but 192.168.9.0 cannot access Internet by using host name. It looks like DNS is not working for the 9.0 network.

View 1 Replies View Related

Cisco Routers :: Connect To RVS4000 With Wrong IP And Subnet

Feb 21, 2013

I tried to update our production switch over the weekend with a newer unmanaged Gigabit switch. Everything was fine after the change and the network had a noticeable change in speed.But when I came back in on Monday the Internet was down. So I tried trouble shooting the switch to see if there was a loop or something like that and put it into managed mode so I could look at the config page and take advantage of the STP function. When trying to get to the config page I entered the default IP into my browser and a logon appeared so I tried to login and it failed then I noticed that the title of the browser tab said RVS4000. So out of curiosity I entered the creds for the router and lo and behold it let me in to the router. The router has a static IP and is using a different subnet then the default IP of 192.168.2.1 that the switch has. I have put the old switch back and removed the new one from production but can still get to the router with either IP, it's static address and the 2.1 address.

View 4 Replies View Related

Cisco Routers :: WRVS4400N Subnet Mask Limitation

Jun 26, 2012

I want to use a subnet mask of 255.255.254.0. The setup window doesn't allow me to type in that mask, rather it only allows me to choose from options on a drop down menu (which doesn't include that mask). Is there a way to do this?

View 2 Replies View Related

Cisco Routers :: Make 2 Different Subnet Talk In LAN Via Rvs4000?

Nov 18, 2012

I have 2 sites located 500 meters away and i connect it via 2 x RVS4000. I managed to get the site to site VPN up Via internet and from my network 192.168.1.x able to reach 192.168.2.x. -where 192.168.1.100 (user try to acces my FTP server 192.168.2.99) has no issues but it's slow due to my internet connection speed.
 
So i setup another link via wireless( wireless bridge ) purpose is to resolve slow connection via internet.
 
But some how i try to set traffics divertion from 192.168.1.x to 192.168.2.99 via local LAN faild.

how possible to setup the network such as picture attached with RVS4000?

View 3 Replies View Related

Cisco Routers :: Connecting 2 RV042 To Different Subnet And DSL Connections?

Apr 29, 2013

Small office, 2 RV042, 2 DSL connections. 1 is used striclty for the business side, and the other is for our CCTV network. They also have seperate DSL connections as we have 2 external IP address for clients to connect remotely. We don't want to take away our exisring setup, but would like to bridge both networks so a few of our internal clients can connect to our CCTV network and use some of the devices. Right now they come in on VPN but its not as fast.Is this doable without adding additional hardware? Both networks need DHCP enable as well.
 
Breakdown:
 
DSL 1
|
RV042
|
192.168.20.X
 
|| Would like to somehow join the 2 networks together.|
  
DSL 2
|
RV042
|
192.168.40.X

View 1 Replies View Related

Cisco Routers :: RV220W - Routing IPv6 Subnet

Feb 27, 2013

I have a few questions regarding IPv6.

Question 1.
I have no idea how to route IPv6. My provider has provided me with a subnet. This subnet is for example 1:1:1::/48

The router of the provider is located at 1:1:1::1 and my router should get 1:1:1::2(Cisco router). Every subnet I want to create must be routed by 1:1:1::2, for example if I want to create 1:1:1:1111::/64 it needs to be routerd by 1:1:1::2

How do I configure this on the RV220w?
 
Question 2.
I have the possibility to create vlans on the RV220W. I can configure IPv4 addressen per vlan. Only for IPv6 this is not possible.How do I configure this or when will new software be released to configure this?Or do I have to edit the configuration file?

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved