I want to use a subnet mask of 255.255.254.0. The setup window doesn't allow me to type in that mask, rather it only allows me to choose from options on a drop down menu (which doesn't include that mask). Is there a way to do this?
View 2 Replieswhat is subnet mask of 10.2.1.3/22
View 1 Replies View RelatedI would like to set the subnet mask off the lan to 255.255.240.0 but the selection menu do not allow to do it.
View 8 Replies View Relatedafter recovering from the PPPoE-port-forwarding-fiasco I had with the RV180 (url...), I decided to try again with a Small Business Router from Cisco. This time I took the RV042G, hoping that the higher age of this product comes with a more mature firmware.So far the functions I need, work satisfying. There is only one issue: The subnet-mask is only configurable using a dropdown-menu. I've read the posts from the Cisco-Support staff saying, that this is because it is only a SMB Router. So, we are a small business and we use the 172.20.x.y net for several reasons. One of it is to distinguish and group several network devices using the third block of the IP. Eg. our printers IPs start with 172.20.5.x and so on.
My question is: Is it really impossible to change the subnet-mask dropdown-menu to a simple text-field in the frontend? Because it is possible to change the subnet to whatever one needs by a little cURL-magic: [code] This sets the new subnet-mask permanently (even survives a reboot and is displayed correctly on the system-status page) and I have not discovered any problems.The only thing is, if you change settings on the setup -> network page, the netmask is reset and you have to rerun this script.
our subnet mask is 255.255.255.0....can I change it to something else like 255.255.0.0.
View 4 Replies View RelatedI have old interface hardware with Static IP 10.2.2.200 and on the same switch I have computers with IPs of 10.4.1.0 If I change subnet to 255.0.0.0 old hardware with 10.2.2.200 will be accessible. The problem is that I would like to have 255.255.255.0 as subnet but it should still be possible to access 10.2.2.200. Can I add Static route for oldhardware in XP without adding gateway settings? The most simple would be to put all on same subnet but it is not possible due to a various reasons. The computers are running Windows XP
View 10 Replies View Relatedwhy do class D doesn't have subnetmask
View 1 Replies View RelatedI want to calculate Subnet Mask for 3 Router Each one in separate building the First building need 60 host and the second building 25 host and the last one 25 host .
Knowing that the company currently reserved public class C network address 210.2.1.0/24 for internal address and subnet 210.15.10.0/30 for the connection to the Internet router.
I understand ip addressing and what a subnet is.But why is it sometimes I connect two things together,it always requires a subnet mask, and other times no? For example when I try to connect two computers together, it requires both IP and subnet mask.But if I use FTP software all it ask for is IP.Same thing when connecting to a website through their ip, doesn't require subnet.
View 6 Replies View RelatedI am using TP-Link wireless router model no. TL-WR941ND.my isp provided static ip via cable modem.ip = a.b.c.d subnet = 255.255.255.254 = /31 but the router does not support subnet mask saying wrong subnet mask?
View 2 Replies View RelatedGiven an IP address range, select the correct subnet mask for the scenario. IP address: 132.250.0.0/16, You need to create 100 networks with a minimum of 500 hosts per network. What is the correct Subnet mask and the 10th subnet address range?
View 1 Replies View Relatedwhat my IP address, my subnet mask, and what my default gateway is. I have tried typing "ipconfig" into CMD but then I only got up 100 boxes saying "Permissionisconnected"
View 12 Replies View RelatedI'm using my WRT320N as a home router, I need more ipadresses to be delivered to my computers, yet I can't get my router to give med wider netmask range. In the list I get 255.255.255.0 - 255.255.255.240 or something like that. I need 255.0.0.0 on my network and that would be perfect if i could get that...
View 5 Replies View Relatedsubnet mask address is illegal cisco linksys?
View 1 Replies View RelatedWe have an ASA 5520, working fine.One of the interfaces is connected to users PCs and printers mainly. Last months the number of devices has grown rapidly, and we would like to make some changes in it in order for it to be able to host new devices.We thought on change subnet mask of actual subnet (10.0.2.0/24) to 10.0.2.0/23, so it can hold as many devices.I understand I have to make some changes in the ASA, but my question is:What will happend to the acces rules I have created?Will I need to create them again? There are some objects which carry information about subnet mask, so I suppose I will need to redefine them, but for those without any subnet mask information, will I have to redefine them?
View 2 Replies View RelatedWe have 10 ADSL lines and 5 of them goes in the load balancer (One gateway) and the rests are used as default gateways for internet access. We use ADSL routers as access points for internet, but those routers should be part of our network and should be given an address in order for them to act as default gateways for internet access. I'm facing a real prob with the ADSL routers Linksys WAG54G2 because they doesn't support a subnet mask 255.255.0.0 Any recommendation for an ADSL router model that support a netmask 255.255.0.0 ?
My cisco 2811 router interface configuration ip address: 172.20.0.1 255.255.254.0.Load balancer output lan ip address: 172.20.0.5.My ADSL routers will be in the following range : 172.20.0.6 - 172.20.0.10
I have an ASA5505 which provides internet (just internet) for about more than 600 pc/laptops. Can 5505's DHCP support this number?
View 4 Replies View RelatedHave a problem with a laptop connecting to a Wireless Router. The laptop was working fine on the last router which was on an ADSL Network.. (not that that matters),When the new router (Virgin Media / Cable) was installed all other laptops where connecting to it without any probs, but not this one.The laptop in question still receives an IP address, Subnet mask and Gateway from the router - Vista says Local only, no internet access. It cannot ping anything else on the network either. When I do ping it comes back destination host unreachable.
View 6 Replies View RelatedFor the past week, I have tried to setup the PPTP VPN server on the RV180. The setup was straight forward, but I could not log-on no matter what I tried. I decided to call Cisco small business support, and as I was talking to the engineer, it mysteriously started to work. I was puzzled and somewhat embarrassed because I'd hate to admit it was an id10t problem on my part. As I tried a few different configurations, I began to realize there might be a limitation in the RV180 PPTP VPN server with the current firmware (1.0.1.9).
In short, the RV180 PPTP only works with 192.168.xxx.xxx/24 subnet. My setup has 3 vlans: vlan1 in 172.xxx.xxx.xxx/24 subnet, vlan2 192.168.0.xxx/24, and vlan3 10.xxx.xxx.xxx/24. My originally plan was to keep vlan3 isolated by disabling inter-vlan routing, but I needed a way to manage a couple of devices on vlan3 remotely, thus I wanted to setup a VPN in the 10.xxx.xxx.xxx/24 subnet. This turned out to be the reason why it never worked before. Today when I called Cisco support, I assigned the PPTP VPN server a 192.168.0.xxx ip range, and it worked. Later, I tried assigning 172.xxx or 10.xxx ip addresses to the PPTP VPN server, and they both failed to work. I created another test vlan4 with 192.168.2.xxx/24 subnet, and assigned the PPTP VPN server to that vlan, and it worked again.
I'd like to mention that I already configured the 10.xxx.xxx.xxx/24 subnet with a few devices before I replaced my router with RV180, and I don't want to have to change and test the setup of all the devices. Another reason I want to have my VPN server outside the 192.168.xxx.xxx range is that it's way too commonly used by wifi hotspots that it increases the chance of wifi and vpn in the same subnet.
I can test a few more configurations, but I think the results will be the same. Perhaps Cisco should test the RV180 in the lab to confirm what I found.
I need to know it the adsl router SRP547w or SRP546 permits to set class B subnetting ( or class A) on the Lan interface. I read the model SRP527 has a limitation to set ip address on the lan interface but I did not find any information about 547 or 546.
View 0 Replies View RelatedWhy does My N750 F1103 (f/w 1.10.16) MAS filter only allow 20, my old Belkin router allowed far more
View 3 Replies View RelatedHow to set up a home network with 2 routers, where R1 acts as the DHCP server and R2 is basically a switch, connected LAN to LAN and everything is on the same subnet. Currently I have a different setup:Both routers have the DHCP server enabled and I connect R2's WAN port to R1 LAN. Therefore I have 2 subnets. Now my special requirement is that R2 is a DD-WRT router, which establishes a VPN connection to StrongVPN, so that all internet traffic via R2 is encrypted and goes through the StrongVPN server. Now my question:If I change my router setup to the same subnet, meaning R2 connects LAN to R1 LAN and I disable DHCP server on R2, will R2 still be able to establish the VPN connection?
View 5 Replies View RelatedI'm trying to set up 2 subnet with two RV042 routers. One router will act as a gateway and both WAN ports will be used by two different isp connection. The first router (gateway) LAN IP will be 192.168.0.1/24. I would also like to set up another router behind the gateway with with separate subnet 192.168.1.X/24. And I would like clients on the 192.168.1.x subnet to use the internet through the gateway router and clients on the 192.168.0.x subnet to access resources on the 192.168.1.x subnet. Am I able to do this with two RV042?
View 6 Replies View RelatedRight out of the box, the WRVS4400N [firmware v2.0.1.3] I just purchased says the WAN interface is DOWN; and it simply will not obtain an IP address from the Arris TM602G cable modem it is attached to. Internet still runs great on the old WRT54G. Is this WRVS4400 DOA? Or is there some arcane setting the quickstart guide overlooks? OR?
View 2 Replies View RelatedI'll just use the 4400n to provide DHCP to my two VLANs and then a new problem cropped up. I am unable to add a default route to the 4400n's DHCP server. It uses the 4400n's vlan IP as the default route. What I'm trying to ultimately achieve is to configure the 4400n as an access point for our "private" network on vlan1 and also "guest" access to the internet on vlan2.
View 12 Replies View RelatedI'm having problems trying to establish a IP Sec tunnel from the office to home. All of our machines are Macs so I have been using the directions described in "How to create an IP Sec tunnel for MAC Clients, A QVPN alternative" but I still can't get it to work. My setup is as follows:
The office is connected to the outside world through a MODEM (Sagemcom 2864 Connection Hub). This MODEM is also a wireless router. It's DHCP server provides addresses 192.168.2.x.The WRVS4400N's WAN port is connected to one of the LAN ports on the MODEM. It's IP address from the MODEM is 192.168.2.x. The WRVS4400N provides addresses 192.168.21.x to devices connected to it.We have a DynDNS account and are using the DDNS client on the WRVS4400N router to connect to it.At home, we have a DIR-655 router with IP Sec Passthru enabled. The router provides IP addresses 192.168.1.x for all devices connected to it. I am fairly sure there are no issues with the router setup at home since I am able to VPN into the office of my full-time job without any problems. I have tried just about everything I can think of but have not been able to get this to work. setting up the Local and Remote Group Settings on the WRVS4400N and the IP address settings in IP Securitas?
Ive setup a few WRVS4400N over the past 6 months, and have been receiving the below message from some of them every couple of hours.What does the message indicate?
View 1 Replies View RelatedI have successfully got QuickVPN working from Windows 7 64bit into my WRVS4400n. The router is sat behind another router/modem (Belkin) as the UK uses PPPoA and the WRVS4400n doesn't.So I set up DMZ and changed the DHCP to always allocate 10.x.x.2 on the Belkin which is the WAN side for the WRVS4400n as it is the only thing attached.I have now noticed, and I'm not sure whether it was the case before, that the DNS that the WRVS4400 is showing is the LAN address for the Belkin Modem/Router (10.x.x.1), not 192.x.x.1 for the WRVS4400n itself. I assumed setting the Static DNS 1 on the WRVS4400n would do it, but it didn't?When I connect into the network with QuickVPN, the computer names do not show even though I have selected the option in QuickVPN?
View 1 Replies View RelatedOur business was looking at purchasing one of these Cisco routers and were curious if it supported WPA2 EAP-TLS?
View 2 Replies View RelatedI have 2 WRVS4400N's available to be. One is running my network and security connected to my WAN.I want to use the other one stricly as a switch or even adding wireless repeat of my current wireless LAN.
View 1 Replies View RelatedRecently installed a WRVS4400N router on my home network. Prior to that I was using the wireless built into my FIOS router. I wanted something more secure so I went with the WRVS4400N. I turned off the FIOS wireless and am only using the cisco wireless.
Im having intermittent issues with the wireless. I have many things hooked up to my wireless including a HP printer and a Sonos system. Most of the time if I just open my ipad I cannot see anything else on my network including the printer. If I try to see the Sonos system can cannot, sometimes I can open the app on my iphone and then I can see it.
Sometimes I can see the printer and sometimes I cant. Sometimes when I do see it and then print to it, it will be gone before it even prints.
I don’t seem to have any issues thru the LAN connections.
Also, ive noticed that the wifi is much slower than the old FIOS box.
FYI, when I remove the cisco and fire back up the FIOS wifi I don’t have any problems at all at any time. And its much faster.
I have tried channel 6, 11 and auto. Also turned off IPC and still no change.
I have a gateway to gateway vpn (home-office) working fine for almost an year btw 2 wrvs4400n routers, This morning, the VPN tunnel was down. I clicked "Connect" from the web based interface, but it does not reconnect.
I tried setting up a new tunnel using the VPN setup wizard, but it says it can't connect to the remote router. Which is strange, since I can ping there normally.
I'm having a heck of a time connecting the WRVS4400N VPN to another WRVS4400N VPN. both of the routers have the current firmware version V2.0.2.1: Router 1 is below, and router 2 has the matching configuration with as it should be the local group being that routers local information and the remote crew set up being router ones information. the status is up on both of the routers, but I'm unable to ping the remote gateway or any device behind it.[code]
View 5 Replies View Related