Routers / Switches :: Transfer WAN From Radio Receiver Through Chain Of Routers

May 24, 2012

For my work I am looking to create wireless capabilities to remote locations. To do this we are using a standard modem/router that is connected to an Engenius (802.11b/g) wireless outdoor radio connected to a dish antenna. We are able to go to locations (3+km) and then with a corresponding receiving antenna (using LoS), receive the Internet and connect both to computers at the transmitting point as well as to the WWW. The problem exists is that we want to employ a series of routers at the receiving end that would be able to carry the transmission to a different location (relatively close), due to the fact that some of the locations do not have line of sight to the antennas. We are using Encore routers, model # ENHWI-N3. When we connect the radio's Ethernet into the routers WAN reciever, we can connect to the Internet with a computer. The problem exists is we want to pass that connection over to a second router (R2). This connection is done when the routers are on access points set to a WDS function with R1 having R2's mac address and vice versa. Both routers are set to channel 1. Even when the routers are seperated by distances >50m a computer plugged into R2 can see a computer plugged into R1. Files can be transferred between the 2 computers wirelessly at speed around 3 mbps. However computer 2 on R2 can not connect to the WWW. This router features a spot that lights up if it has Internet access and R1's is lit up but R2's is not. How do we transfer the Internet and not just a LAN from R1 to R2 so it can be accessed further away from the point of the radio and antenna equipment. This setup has also been used where R2 is hardwired to R3. At R3 we change the channel to 11, and then connect through that with mac addresses wirelessly to 4th router. If comp is in R4 and far away it can still access and file share from comp at R1.*edit the ip address for the routers exist all on 192.168.1.xxx If the 3rd number is different between routers would this make a difference?

View 1 Replies


ADVERTISEMENT

Routers / Switches :: Daisy Chain 3 Switches And Not Have Ip Conflict?

Jan 31, 2011

Is it possible to daisy chain 3 switches and not have ip conflict? I am running a public access network for a library. For certain library software I need for all workstations to see each other. I have 25 workstations in total and two separate management consoles. I have all workstations on two switches but one of the management consoles is on the third switch because when joined with the others it has an ip conflict. I need this console for the digital sender that is connected as well as to act as a server for go print software.

View 3 Replies View Related

Routers / Switches :: Connect Landline Phone To Use As Talkback On Radio?

Jan 12, 2012

how to connect landline phone to use as talkback on my radio

View 1 Replies View Related

Routers / Switches :: Transfer Speed Different Between Two Computer?

Jan 12, 2011

I bought a new laptop today, unfortunately, it doesnt have a Firewire port and i want to use it for video editing.But i figured no problem really, i'll just capture on my desktop that i have been previously using to edit on, using Premiere pro to edit, but HDVsplit to capture, and then transfer the files over to the laptop using a USB or possibly trying to setup a home network.But when transferring files from the desktop onto the laptop via the router using ethernet cables, the speed is about 250 kb/s and when its the other way around, from the laptop to the desktop, the speed is 10 MB/s! I really need to find away to speed this up as the overall files i want to transfer are over 5GB.You can read a bit more about it here: [URL]

View 1 Replies View Related

Possible To Have Two Routers Coming Off Another / Does It Need To Be Proper Chain

Feb 17, 2011

I live in a house with four other people so I need a lot of free ethernet ports.I currently have three routers daisy-chained together and I want to add a fourth, but I can't seem to.When I plug it up, pages refuse to load on computers connected to it. I read something about disabling DHCP, but I have two other routers chained to my primary and didn't need to do that. This one's branching off the main one though, instead of being at the end of the chain.I'm trying to hook up either the Linksys 4-port wired router or the 8-port one (I have both). I tried disabling DHCP on it and setting the IP thing to 192.168.2.1 instead of 192.168.1.1 and it worked for a few minutes, then nothing.I also tried that with the TRENDnet one and the same thing happened (had to reset that one to factory defaults).Is it possible to have two routers coming off another or does it need to be a proper chain? Why did I not have to disable DHCP on the others and they still work fine?

View 4 Replies View Related

How To Configure Daisy Chain On Routers

Jan 21, 2012

How to configure daisy chain on 3 routers ?

View 1 Replies View Related

How To Daisy Chain 2 Linksys EA3500 Wireless Routers

Nov 26, 2012

I need to extend my wireless N network to increase the wireless reception power to a VIZIO Smart HDTV. I currently have a Linksys WRT310N router that is just barley being seen by the TV, Sometimes yes and sometimes not.I have just ordered a Linksys EA3500 Smart Wi-Fi Router. I want to set the EA3500 as the 1st (primary) router and CAT6 cable connect the WRT310N 50 ft closer to the HDTV.

View 1 Replies View Related

Daisy Chain 3 Wifi Routers - How To Extra 4 Ports On To Second Stage Router

Jan 16, 2013

I have got 3 wifi routers i want to daisy chain. Router 1 is main modem router, which is connected to 2 pcs and 2 wif routers (wired separately), both of these wifi routers have there own ip address and dchp turned off, so they work fine and broadcast wifi nicely. now what i want to do is connect another wifi router to one of these routers (not the main one) but what setting do i need? i tried to connect the 3rd wifi router with the same setting as per the other two ie diff ip and dchp off, but when i plugged it into the port of the second router it would not show as connected or get an internet connection. Its probably quite simple to sort out, but with me being a dimwit i am tering my air out. If i could not use a wifi router for this 3rd connection, is there any other way of putting an extra 4 ports on to my second stage router.

View 4 Replies View Related

Cisco Routers :: RVS 4000 - Allow Radio Button Stippled Out

Jan 17, 2012

This type of issue has been posted time and time again by others.  In this particular instance the ability to deny and allow access based on a time and day for one or more MAC id or IP address or range of addresses does not work.  Because the code is so "weak" that it cannot handle a policy which passes the midnight threshold into the morning (the test is actually commented out in the code), one is forced to write one, perhaps two inverse permit rule(s).  In this case, it cannot be done because the "allow" radio button is stippled out.
 
Some simple digging reveals that the file AccessRes.htm gets to the browser with the "allow" radio button stippled out because the token "disabled" appears in the generated html.
 
<input type="radio" value="allow" name="f_status2" onclick="setBLOCK()" disabled="">
 
I have several of these devices.  They are all new V2 units. They all have the latest version of the firmware and they are all broken the same way.  This behavior is the same on various flavors of browser.  As an experiment, based on SOP responses I've read, I downloaded and flashed with the latest firmware (same version as delivered), and then performed the factory reset.  No change.  It's broken.

View 1 Replies View Related

Routers / Switches :: Smurf Attacks On Belkin Wireless Routers Reply?

Jan 2, 2013

If your wireless indicator is flashing red when you discover the smurf, it can mean that someone has tried to logon with an incorrect password. this is not necessarily an attack, it could be someone you have allowed access too, who has forgotten the password? In this case entering the correct password will solve the problem.However putting your own MAC address into the filter will simply block your own machine.

View 6 Replies View Related

Routers / Switches :: D-Link And Linksys Routers Plus Modem Connection

May 26, 2011

everything was all good, my brother went crazy and unplugged everything.it effects our house phone too, that could be the problem.i just dont know what wires went where. all the wires are the same color.but i know which is which. just again, dont know where.i would like to get it done before he gets home later on.

View 1 Replies View Related

Daisy Chain 2 Pro-curve 1810g 8 Port Switches

Jan 8, 2012

i am trying to daisy chain 2 pro-curve 1810g 8 port switches.i got the cable i need to connect them but i just want to know what kind of settings i have to change on the switches to have it run as best as it can.

View 17 Replies View Related

Routers / Switches :: How To Install Two Wireless Routers In Series

Dec 31, 2012

The first router is wired to the DSL modem and works just fine as an access point with Internet access. The second router is wired from the first router using one of the 4 ports on both router hubs. The second router is visible but has no Internet. How to configure the second router regarding DHCP, LAN, WAN, DNS etc.

View 3 Replies View Related

Routers / Switches :: Change Two Old DLink Routers To Repeaters

Nov 28, 2011

What are procedures to deactivate di-604+di-704 routers+make the repeaters,connecting each of them,in a wired fashion,to my Belkin wireless N router?

View 1 Replies View Related

Routers / Switches :: Install 3 Routers In One Location With Same Password?

Mar 10, 2012

how to installs 3 router with same password

View 2 Replies View Related

Routers / Switches :: Networking With Switch / Bridge And Routers?

Jun 13, 2011

modem
........ |
........ |
----switch-----
|................ |
|................ |
Router 1.... Router 2
|..................... |
|..................... |
Computer 1.....Computer 2

......................Computer 3 Router 1 points to a VPNRouter 2 access to the internetComputer 3 needs to access router 1 (VPN). Both Computer 2 and 3 are in a different room than computer 1, and router 1. Computer 2 is networked via cat5e to router 2.Is is possible to have Computer 2 and 3 share the cat5e, yet access different routers?

View 5 Replies View Related

Routers / Switches :: Possible To Connect 2 Routers To One Phone Line

Apr 30, 2011

Can I connect 2 routers to one phone line so that I can receive a wireless internet connection throughout my house?

View 1 Replies View Related

Routers / Switches :: 2 Routers On Same Subnet With DD-WRT VPN Tunnel On Second?

Mar 13, 2012

How to set up a home network with 2 routers, where R1 acts as the DHCP server and R2 is basically a switch, connected LAN to LAN and everything is on the same subnet. Currently I have a different setup:Both routers have the DHCP server enabled and I connect R2's WAN port to R1 LAN. Therefore I have 2 subnets. Now my special requirement is that R2 is a DD-WRT router, which establishes a VPN connection to StrongVPN, so that all internet traffic via R2 is encrypted and goes through the StrongVPN server. Now my question:If I change my router setup to the same subnet, meaning R2 connects LAN to R1 LAN and I disable DHCP server on R2, will R2 still be able to establish the VPN connection?

View 5 Replies View Related

Routers / Switches :: How To Bridge Two Routers Over The Internet

Apr 26, 2012

i want to ask if i can link two routers while they are totally separated of each other over the internet to make a large LAN the two routers are TP link?

View 5 Replies View Related

Routers / Switches :: How To Connect Two Internet Routers To One LAN

Mar 8, 2011

How do i connect two internet routers to one IP address range?I currently have one broadband router connected on 172.16.0.3 subnet 255.255.0.0, I have a second line which is a copper ethernet EFM 2Mb line connected using a Cisco 1800 router configured on 172.16.0.254 subnet 255.255.255.0, no DHCP is configured on either router. the dhcp is provided by a windows 2003 server on our LAN which is also configured on the same LAN IP range. if i connect the Cisco router into the same switch as the broadband router my network devices stop working and dont respond.

If i check the broadband router it shows all the connections to it as having the same MAC address as the Cisco router?? if i disconnect the Cisco router everything returns back to normal and works perfectly.What I want to achieve is to be able to run both routers on the same LAN to provide internet access by configuring the pc's to route through a specific router. the DHCP I want to stay routed through my original broadband line. at the same time i want all pc's to access to the lan devices (ie. servers and printers) what the correct configuration would be for the two internet routers would be?

View 5 Replies View Related

Routers / Switches :: Configure Two GB Routers On The Same Network?

Jul 26, 2012

I have one cisco 2851 router and one watchguare firewal currently being used as the main router. I want to connect the cisco as a secondary router on the same network.

View 10 Replies View Related

Routers / Switches :: How To Connect 2 Routers On A Network

Jan 19, 2011

how to connect 2 routers on different lan

View 3 Replies View Related

Routers / Switches :: Using Multiple Routers With DSL Modem?

Oct 24, 2011

In my office we have concrete walls and very limited wiring. The way it is set up is we have a Verizon DSL Modem that comes in then I have a router with it that splits the signal to 4 other routers that each split the signal 2 to 3 more times. I have to use routers so that it assigns IP addresses.I bought a new D-Line N300 Wireless router with USB imput. I want to attach my Home Media Network Hard Drive Cloud edition to the 1st router (attached to the modem) and then share the data off that hard drive with everyone connected to the sub routers.

View 4 Replies View Related

Routers / Switches :: Connect 2 Wireless Routers Together

Jan 21, 2013

I am trying to connect 2 wireless routers to expand my wireless signal. I want to connect the router 1 (in 2d floor) to a powerline av and then get the router 2 to the powerline (in the ground floor) so i can have wireless there too. I've tried some configurations i found online, but can't get to make the network functioning. The routers and powerline av are all dlink. I don't mind having 2 networks, but it would be better to have only one

View 4 Replies View Related

Routers / Switches :: How To Connect 2 Routers To 1 Laptop

Aug 18, 2012

I have a laptop connected to a net gear wireless router (for internet), but I am very close to buying a Belkin network USB hub to make my hard drive wireless, but this requires a router. I do not want move my hard drive to where my net gear router is, so I need to get another router, i am looking at a Belkin router so that I can make my hard drive wireless (This is the only reason for the router, it will not be used for internet) so I can keep my hard drive in the same place.

View 9 Replies View Related

Routers / Switches :: How To Hook Up 2 Ip Cameras Using 2 Routers

May 12, 2011

I would like to hook up 2 ip cameras to a server. I need to use 2 routers to do this. I already have the routers. router a is hooked up to the server. router b needs to connect wirelessly to router a. I can then hook up the ip cameras to router b. I just can seem to get it figured out.

View 9 Replies View Related

Routers / Switches :: Want To Connect Two Routers Wireless

Sep 19, 2011

I want to connect two routers wirelessly without running cables , any easiest way without cables.

View 1 Replies View Related

Maximum Transfer Speed On Concurrent Dual Band Routers?

Feb 19, 2012

i am going to purchase a Simultaneous Dual Band Router with Gigabit Lan. Can anybody tell me whats the transfer speed it got on Concurrent Dual Band 900(450+450) , 750(300+450) and 600(300+300). I am going to use it for hard drive that can network attached or may be just external hard drive via USB interface.

View 2 Replies View Related

Cisco Routers :: RV220W Wireless File Transfer Slow At 2MBps?

Jul 23, 2012

I have a RV220W operating in 2.4GHz N-only mode. Channel bandwidth is set to 20MHz, channel to 6 (a site survey shows that channel as completely clear), WPA2/AES. I am connected to a TrendNet wireless bridge. The admin page for that wireless bridge shows a link quality of 100% with a signal strength of 71%. If I select a higher channel (11), the signal strength drops to 51%.
 
I have a Windows 7 PC connected to the Trendnet bridge and a Windows 7 server connected to the RV220W, both via a 1Gbps LAN port. When I transfer a file from the server to the PC or vice versa, I get a lowsy 2MBps (~20Mbps) transfer rate. That seems awfully slow. I tried channel bonding from 20 to 40 MHz

View 2 Replies View Related

Routers / Switches :: Accessing Two Routers From The Same LAN?

Aug 20, 2011

I have a little probs@a site .we have a vsat link connected to a linksys E1000 router which is pluged into a cisco 2950 switch doing DHCP to the LAN,then a WAN link configured on a cisco 2911 router on static ip which is pluged into the same switch to serve the same LAN.I have been having issues of the workstations accessing both the WAN and internet@ the same time.

View 1 Replies View Related

Routers / Switches :: Setup An Home Network With A Wireless Router And Use Multiple Switches?

Jan 29, 2011

I want to setup an home network with a wireless router and use multiple switches for wired connections through out my home. I currently have an Airport extreme hooked up to a cable modem and a leviton gateway hooked up to the Airport. The 2 computers connected to the Leviton are on a windows 7 homegroup and share fine, but won't share or discover any wireless device connected to Airport. My main goal is to have a wireless/wired network with all computers sharing information with each other. I want 2-3 wired switches/gateways with a min of 2 devices connected to each, connected to my wireless router whiich is connected to cable modem.

View 3 Replies View Related

Routers / Switches :: Connect 2 Subnets With Two Switches And One Router Using SIM Software?

Apr 23, 2011

how to connect two subnets with two switches and one router using router sim software?

View 1 Replies View Related

Routers / Switches :: How To Use Two Routers - One For Each PC

Feb 13, 2011

I have two desktop PC's Can I use arouter for each on the same tel line

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved