Cisco Rv042 (obtain an ip automatically) problam ?,Firmware Version : v4.1.0.02-tm (Sep 16 2011 18:40:48)
DHCP Server Working, but Cisco Rv042 can't obtain an ip address autimatically on WAN Ports.
I am setting up a dual WAN network in our small business office and I am confussed on the set up of the RV042.
On WAN1 I have a satellite modem connected
On WAN2 I have a cradlepoint CTR35 Router with a verizon aircard
The satellite has lag issues and will drop out during poor weather but has a 17GB dowload limit. The verizon aircard has only 5GB download limit but normally works in poor weather. Code...
Do I select obtain DNS automatically on both WAN1 and 2? Do I set this up as a gateway or a router?
I just got a new RV042. V3 Hw.For setup and testing before putting it in action, I've attached the WAN1 side to my internal network.But it fails to get an IP address, and the log shows: "Infinite lease time, exiting".My current router on the LAN is giving out DHCP addresses with 3 hour lease time, and I've checked with the PC's on the LAN that this is correct.The routers DHCP status shows that the lease time for the RV042 is 3 hours ahead.So why does the RV042 complain about long lease time ?Is there a way to avoid this error from occurring?
I have tried to change from 'Gateway' to 'Router', but this does not change anything.Also tried a factory reset, with no luck.Fw is upgraded to the latest 4.0.4.02
I purchased 2 RV042's (h/w version 3) less than two months ago. I updated them to the latest firmware (v4.0.4.02-tm (Jul 4 2011 13:30:56)), did a factory reset to make sure I was working with a clean slate, set up DDNS through DynDNS and a site to site VPN between the two. Everything was working great for a month, then the DynDNS accounts expired because they weren't being updated. I reactivated the names on the DynDNS site, and started to monitor the "last updated" date and time. After 24 hours there were no updates according to the DynDNS site. I logged into one of the RV042's, and it said "Dyndns Enabled : Dynamic DNS is updated successfully." This is a stale message from 24 hours ago when I hit save. So I went into Setup | Dynamic DNS | Edit Config and there it also says "Dynamic DNS is updated successfully." I clicked "Save", status changed to " Dyndns Enabled : Updating..." for a few seconds, and then back to "Dyndns Enabled : Dynamic DNS is updated successfully". I refreshed the DynDNS website and it shows the current time (in eastern time, i'm pacfic) as the last time it was updated. So it works when I manually hit the "Save" button. Not making any changed, just hitting "Save". I've let the other RV042 go over 48 hours and it still hasn't updated. So it apears for the time being, I'll have to remember to push the "Save" button once a week to prevent my DynDNS accout from expiring. Does DDNS working in the lastest firmware and h/w version 3? If so, what is the update frequency?
View 6 Replies View RelatedI coulden't visit any websites and it gave me an "error 105" something. So i tried connecting my other comp to the internet cabel with the same result. So i tried to find a solution on the web (wierless internet still worked) and stumbeld upon a similar problem were the answer was to manually fill in an adress in the "internet protocol version 4" properties in the "local area connection" properties. I then noticed that i dident have the "Obtain DNS server address" set to automatically and that the other manual boxes were empty. I then turned the auto on an i had access to internet. Is this safe? Cause i read somewere that DNS server addresess were provided by the company that provide you your internet service, and that you can be redericted to a fake website that can get a hold of your account information on it
View 1 Replies View RelatedI would like to know on how can i setup my cisco 877 router at my small office. Here are the things that i need to do:
1. I need enter the internet static ip address 61.10.xx.xx/subnet mask/gateway/dns provided by my ISP.
2. I need to configure the cisco router DHCP so that the 4 computers can obtain an IP automatically. Howow can i accomplish this setup.
I have a problem with my RV220W.
It reboots randomly every day and I got the following message in the log: [rv220w] System][FIREWALL] fwPPTPGenericRules.c: inet_aton failed I saw one internet that I can ask cisco for the Beta firmware 1.0.4.6 that fix the issues(Iactually use 1.0.4.17). Is it the solution? How can I obtain the beta firmware?
I have two RV082's connected across the internets using the primary WAN ports. They are both set to Auto Load Balance. Both ends of the VPN are set to "IP Only, IP by DNS Resolved".
If I attempt to access the remote subnet, the VPN won't automatically initiate a connection. However, if I do a "Tunnel Test" connection on both routers, then the remote subnet access works just fine.
Should the router automatically connect the VPN when a remote subnet is attempted? If so, what might I do to make it connect automatically?
How do I get one of these to automatically bring up the VPN tunnel without the end user having to login and click connect? I got the VPN working Dynamic to ASA static, but it doesnt come up on its own when I try to access something over VPN.
View 7 Replies View RelatedI have RV042 and E4200 routers . I tried the manual UPnP port forwarding using Rv042 router and was succesful ( by typing 192.168.1.1 in the explorer and logged in using user name and password )
I am using a linux embedded system whose Internal IP ,Internal port are mapped .This system is connected to one of the LAN ports
I want to try auto UPnP port forwarding both for RV042 router and Linksys E4200 routers
After enabling the Upnp option only and logging out ,Can i add a port mapping entry in this router without logging in using a C++ program which runs on linux embedded system .
I was looking for a small business router that has VPN support and dual WAN support for load balancing. Upon reading reviews, I think RV042/RV042G is a good choice. Now am thinking if it supports intervlan/ router-on-a-stick configuration?
View 5 Replies View RelatedI am using using 2 broadband with tp-link dual wan router 10 pc using the broadband.does any one know about the router who controls bandwith there is option available in Tp-Link Dual wan router but its not working...is there any router which automatically takes bandwith and allow as per my details.
View 1 Replies View RelatedI have a cisco RV180W with a IPsec tunnel to the head office. The tunnel is working good, but if I reboot the RV180W, the tunnel don’t reconnect automatically, I need to go in the admin interface to IPsec Connections Status and press on Connect.Is there a way to make the tunnel connect automatically?
View 4 Replies View RelatedI have a new d-link wireless N 150 home router DIR-600. I heard of the wan ping which works it connect for online gaming, does or does it not turn on when you install it and is there any other things i can do to improve it? can't connect to League of legends
View 4 Replies View RelatedI have two Internet connections-
1-DSL Modem (WAN1-Internet Port)
2-Cable Modem-Comcast (WAN2-DMZ/Internet Port)
I connected the DSL (WAN1-Internet) port in and the Cisco RV042 was able to get an IP automatically. I tested the connection and it works just fine. Then I connect the Cable Modem-Comcast (WAN2-DMZ/Internet Port) in and I have the RV042 automatically optain IP address. But it just says 0.0.0.0. I've tried release/renew and that does nothing. Also, when I connect the 2nd Internet connection the Internet goes down. The only way it goes back up is when I disable under the PORT MANAGMENT setting.
All the settings have been kept to the default.How can I get the router to obtain an IP address from the Cable Modem-Comcast (WAN2 DMZ/Internet Port).
We have an Cisco RV042. We need to setup a VPN with a business partner who is already using our current IP scheme on another VPN with another client. They have asked us to NAT our IP's from 192.168.25.x to 192.168.245.x
I can't seem to figure this out on this router. I have done it on a Sonicwall and Watchguard, but can't seem to get it to work on the RV042.
I have setup the VPN and the One-To-One NAT. The tunnel will connect (using the 245.x IP as our local IP on the VPN setup), but no traffic will pass through.
i was planed to make a vpn over rv042 so i get the rv042 connected behind a thosmon 456(configured as a bridge) and 1 static ip ... and i configured the vpn and worked great ...but due to some circumstance i get a package of 6 ips insted of the old ip , so when i try to configure the router with the ISP they but the wan ip 10.232.x.x and told me that an internal ip from there lan ... and give me the 6 ip of 196.x.x.x to use as 1 for internal interface for the rv042 and 5 for the pc's,now the vpn not working anymore...notice: when try to configure the vpn tunnle in the local securty setting i mark the ip only and the ip that abear is the wan ip 10.232.x.x but i can't ping that ip beside i can ping the internal ip of the router 196.x.x.50does rv042 can support static and virtual ip inside the lan |! can i configure the thomson as pppoe and use one static ip from 196.x.x.x as wan ip for it ... and use anther 196.x.x.x ip for the rv042 to get access from outside and connect the lan to the rv042 with internal ip 192.168.x.x ...so i can access the vpn from outside .....and can connect the device i need to use static ip to the thomson ...
View 0 Replies View RelatedFirmware v4.0.4.02 has a nasty bug in the VPN section. If you switch to "IP by DNS Resolved" (yes, it says "Resolved" instead of "Resolution". Gotta love all the Engrish in the RV042!), it will automatically populate the field with "@yourdomain.com". This will cause the VPN to not lookup the proper IP address. Simply deleting the atmark after it populates will fix the problem.
Let's see what happens when we validate a Cisco RV042 webpage:
Errors found while checking this document as HTML 4.01 Transitional!
Result: 353 Errors, 1 warning(s)
Don't even get me started on the horrible Javascript...
i am trying to make a simple Site to SiteVPN between two offices, one has Cisco ASA and one has RV042 router.when traffic initiated from ASA side, i keep getting this message in Debug and tunnel wont come up
.
[IKEv1]: Group = A.A.A.139, IP = A.A.A.139, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.Apr 26 00:15:53 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
whereas if traffic initiated from RV042 side, i keep getting this message in debug and tunnel wont come up.
Apr 26 00:43:44 [IKEv1 DEBUG]: IP = RV.RV.RV.139, Oakley proposal is acceptableApr 26 00:43:44 [IKEv1 DEBUG]: IP = RV.RV.RV.139, IKE SA Proposal # 1, Transform # 0 acceptable Matches global IKE entry # 6Apr 26 00:43:44 [IKEv1]: IP = RV.RV.RV.139, Connection landed on tunnel_group RV.RV.RV.139Apr 26 00:43:45 [IKEv1]: IP = RV.RV.RV.139, Connection landed on tunnel_group RV.RV.RV.139Apr 26 00:43:45 [IKEv1]: Group = RV.RV.RV.139, IP = RV.RV.RV.139, Freeing previously allocated memory for authorization-dn-attributesApr 26 00:43:45 [IKEv1]: Group = RV.RV.RV.139, IP = RV.RV.RV.139, PHASE 1 COMPLETEDApr 26 00:43:45 [IKEv1]: IP =RV.RV.RV.139, Keep-alive type for this connection: DPDApr 26 00:43:45 [IKEv1 DEBUG]: Group =
[code].....
Apparently one of my two ISPs,CenturyLink, supports 6rd connections to IPv6.
This is supported natively on my Q1000 ActionTec modem, however my modem is in "transparent bridging" mode, so that the RV042 v3 can be the only router.
how to configure the RV042 to operate in this manner.
Per the CenturyLink FAQ: the IPv6 address space is:
2602::0 /24
Most importantly, can I do this WITHOUT buying a new modem.
I have a RV042 router (Ser#: NKS10462300, HW V3) running Firmware version v4.0.2.08-tm (Jan 14 2011 22:08:38) set up as a gateway. Right after it boots I am able to long into its web interface but shortly after that if I try to log into it I go through a very log time out while the web page is waiting the router to respond and then eventually IE comes back and says it 'cannot display the web [age'.
View 30 Replies View RelatedI have a Cisco RV042 VPN Router and I have added a group vpn, but when I am trying to connect I got an error that the remote vpn server isn't responding.
Here's my log:
2013/01/15 12:24:53 [STATUS]OS Version: Windows 7
2013/01/15 12:24:53 [STATUS]Windows Firewall Domain Profile Settings: ON
2013/01/15 12:24:53 [STATUS]Windows Firewall Private Profile Settings: OFF
2013/01/15 12:24:53 [STATUS]Windows Firewall Private Profile Settings: OFF
2013/01/15 12:24:53 [STATUS]One network interface detected with IP address MY HOME IP
[code]....
If I am trying to connect the status of the vpn user in the remote interface is "online".I have deactived my firewall at home and at the server for testing purposes.
I am looking to configure RV042 for VPN access to local machines and Win 2008 server. The story: Had issues with remote printers being created for clients logging into old Linksys RV042 with Linksys VPN software. First Tech exposed server without security, and it had to be removed as it was being attacked, but did not fix printing issue. 2nd tech could not get VPN to work after 1st tech. 3rd tech, 4hours, and I got that the router is a piece of ... So I'm out over 1000, and not able to have a simple router set up. The present situation. New RV042 with firmware V4.1.1.01, using Cisco VPN client 5.0.07.0410, most XP 32 bit machines coming into network, one 64 bit win 7. My clients have been unable to access their data for too long.
View 3 Replies View RelatedIs there any documentation out there on a step-by-step instructions on setting up a vpn on a RV042 router?
View 1 Replies View RelatedI'm trying to set up 2 subnet with two RV042 routers. One router will act as a gateway and both WAN ports will be used by two different isp connection. The first router (gateway) LAN IP will be 192.168.0.1/24. I would also like to set up another router behind the gateway with with separate subnet 192.168.1.X/24. And I would like clients on the 192.168.1.x subnet to use the internet through the gateway router and clients on the 192.168.0.x subnet to access resources on the 192.168.1.x subnet. Am I able to do this with two RV042?
View 6 Replies View RelatedThe issue is when I am using PPTP the router seems to die, not every time but I would say about once a week now. I am the only PPTP user, simply using RDP. A few hours into an RDP session the PPTP connection drops and cannot be re-established, or quickvpn, nothing. Routing still works (somewhat, high latency) locally.
When I've checked the logs both times I see:
TimeEvent-TypeMessageSep 3 17:07:56 2012KernelOut of memory: Killed process 14354 (pppd). Sep 3 17:07:56 2012KernelOut of Memory: Kill process 14354 (pppd) score 177 and children. Sep 3 17:07:56 2012KernelOut of memory: Killed process 14367 (sh). Sep 3 17:07:56 2012KernelOut of Memory: Kill process 14354 (pppd) score 234 and children. Sep 3 16:46:41 2012KernelOut of memory: Killed process 14330 (pppd). Sep 3 16:46:41 2012KernelOut of Memory: Kill process 14329 (pptpctrl) score 134 and children. Sep 3 16:46:41 2012KernelOut of memory: Killed process 14324 (pppd). Sep 3 16:46:41 2012KernelOut of Memory: Kill process 14324 (pppd) score 177 and children. Sep 3 16:46:40 2012KernelOut of memory: Killed process 14328 (sh). Sep 3 16:46:40 2012KernelOut of Memory: Kill process 14324 (pppd) score 234 and children. Sep 3 15:36:15 2012KernelOut of memory: Killed process 14187 (pppd). Sep 3
[code]....
I have an RV042 connected via VPN to the office (to a LinkSys DFL-700). Sometimes the VPN is dropped and never activates again. In this state, if I try to connect to the WEB interface, I can log in, but the router hangs at the login screen. I have to power recycle the router to make it work again.
Updated to latest firmware 4.2.1.02 for V3 hardware. The funny thing is that services from the WEB routed through to local IP adresses on the lan is still accessible. I have setup PPPT VPN on the router, and that also fails to work.
Is there, as a workaround, any possibility to access the routers reset page or access via TELNET to reset the router? This migth be useful, when I'm out. (I have a backup solution to access the local network at home).
I have just purchased the RV042 and while it is working great on WAN1 over Xfinity/Comcast broadband, I'm unable to get it working with my AT&T DSL for WAN2. I am planning on running this in failover mode - not load balancing.
The DSL modem it is connected to is a SpeedStream (hooking up laptop directly works etc. etc.). The SpeedStream is set to PPOE authentication passed in via the computer (in this case the RV042). On the RV042 side, I set it to use PPOE, using the credentials as given my AT&T DSL. The DNS servers are set to the ones recommended
Are the RV042 and RV082 routers SIP AWARE?I haven't had any luck finding documentation stating such.
View 2 Replies View Relatedi have setup vpn connection (client-gateway) using quick vpn ( default cisco) and third party like thegreenbow. connection is ok (established) but why from outside I can only ping to IP LAN PC , if I ping ip server the result is request time out(failed). I have been trying do this to 3 server ( windows server 2003 as OS).four your information I have made firewall "OFF" on all of those servers. the result is same, failed.
View 0 Replies View RelatedI'm tryig to put a computer into the DMZ and then access it from computers on the LAN using a local IP address. My reason for doing this is that I'd like my DMZ computer to be a locked down web server (just ports 80 and 443 open to the outside), but I need to be able to have more access to it from inside my LAN (e.g. I want to be able to SSH into it from the LAN).
Thus far I've been able to get a computer set up in the DMZ and can access the Internet from the DMZ computer. And I can access the DMZ computer from the LAN computers using the public address for the DMZ computer. But I can't access the DMZ computer from the LAN computers using a private address for the DMZ computer. see the attached file for a diagram of our current settings. A few descriptions:
- Verizon provides us with a number of static IP addresses, i.e. 71.123.123.10-12 (note these aren't actually the addresses, but representative).
-- In the RV042, I have the following configurations made:
- Setup > Network > LAN Setting
- Device IP Address = 10.4.20.1
[Code]......
I have a static DSL connection and my ISP is giving me 4 static IP's. I have connected my RV042 to the DSL modem and I have now 1 subnet at 192.168.0.0. What I want to create is a WEB server/ Email server, but to sit on a different subnet - 192.168.5.0. For now I have connected the server to the DMZ port, but I am unable to to access it from WAN, only from LAN. How to configure properly the 2 subnets (192.168.0.0 and 192.168.5.0) and how to forward my static address to the server which I which to be on the 192.168.5.0.
View 4 Replies View Relatedi'm trying to set up a simple VPN (client to Gateway), but i can't ! An SSL VPN or an IPSEC VPN, whatever..
The firmware of the RV042 is up to date, and i'm trying QuickVPN as a client vpn (also updated...)
My configuration details :
I'm in : 192.168.2.14 /24
My RV042 : 192.168.2.250 /24
And the VPN intend to connect me to : 192.168.4.x
[Code].....