I've attached my ASA's config. I can't bring the VPN up by pinging from the ASA but the VPN will come up when someone pings from behind the ISA server. So the problem seems to be routing/NAT on my ASA because my pings aren't being directed out the tunnel. The VPN in question has 64.106.x.x as the peer and AES 256/SHA for phase 1 and 2.
View 2 RepliesIm trying to setup a site to site VPN using a Cisco 877, problem is we have no ADSL presentation, we've just been given an Ethernet line to use from another client in the building, If i plug my laptop into the port and use the External IP information given i can use the internet and ping the other VPN just fine, if i place my blank config 877 into the port and set up VLAN 10 to use the same IP information, it cant even ping the local gateway? The port on the router is in VLAN 10 like it should be and the interfaces are all up, the router can ping its local VLAN 10 ip address.
View 5 Replies View RelatedI have 2 ASR 1006 with ASR-1000-ESP40, ASR-1000-SIP40, ASR-1000-RP2 , and with SPA-1X10GE-L-V2 that should hold an XFP-10G-MM-SR.
i am in the proceed of an implementation and configuration, but i am facing a problem on the interfaces, where i am not able to bring the interfaces up/up and always down/down.
i check the fiber patch cords and the other SFP on the switch WS-C3560E-12D and it is working fine. i also reverse the fibers pins and nothing works
i need only to get the interface to be up/up. i also checked all the hardware compatibility matrix, IOS XE, the SPA are all online (show platforms).... where all seems to be ok and compatible.
all what is needed is to give the interface ,for example, tengig0/0/0 and ip address and no shut and it should go up/up.
One more thing, the XFP is not giving a red light laser, and in the show interface tengig0/0/0 give media type is unknown.
I know I can bring up a tunnel up-and-up without any layer 3 address, without any ipv4 or ipv6 address (apart from tunnel source/destination of course). And I don't have to use "ip unnumbered <interface>" either. But what good is a tunnel interface with no address? Can you bridge them or something?
View 5 Replies View RelatedI am trying to configure an IPSEC tunnel on a 1921 router. What I hope to accomplish is that using a IP SLA that the IPSEC tunnel will only be brought up IF the normal WAN connection is not responding. My thoughts were to route the traffic that needed to come back to corporate through a loopback interface but I havent found a way to do that.
View 1 Replies View RelatedI'm trying to bring up two t1 and bundle them into a multilink on a 3845 on one end and a 3725 on the other end. On the 3845 I have installed two VWIC-2MFT-T1-DI and on the 3725 I have installed two VWIC-2MFT-T1 and a 1DSU/CSU-T1-V2.
For some reason I'm able to bring up the T1's on the DSU/CSU WIC. When I try to connect the T1 on the other WICs, on the 3845 I see SLIPs and Interface Resets however on the 3725 there is no errors however I still see UP DOWN.
CONFIG 3845
controller T1 2/0/0
framing esf
linecode b8zs
cablelength short 133
channel-group 0 timeslots 1-24 speed 64
[code]....
Have already checked in the Device Manager if the �Allow this device to wake the computer� is unchecked.What do I do to bring the sleep mode back without turning off the file sharing (if file sharing caused the problem)?
View 1 Replies View RelatedHow do I get one of these to automatically bring up the VPN tunnel without the end user having to login and click connect? I got the VPN working Dynamic to ASA static, but it doesnt come up on its own when I try to access something over VPN.
View 7 Replies View RelatedI've to bring vlan 2 access to a remote site through 2 AP1261N configured as bridges. Here it is the network diagram
One AP1261N is configured as root bridge. Its ethernet interface is connected to a switch with vlan 1 native and vlan 2 tagged. Vlan 1 is for APs and switches management. Vlan 2 is for users access. The other AP1261N is configured as non-root bridge and one PC is directly connected to the AP's ethernet interface. I've successfully managed to create i wireless link between the 2 APs and so I can reach the vlan 1 IP address of the non-root AP. My problem is that I can't reach the PC connected to the non-root AP.
Here are the conf of the 2 APs:
root AP
version 15.2
no service pad
[Code].....
getting step by step procedure to bring an ASA5550 to factory default setting, so that I can configure it from scratch via ASDM
View 3 Replies View RelatedI have 2 4402 WLC running 7.x.x.x code. I also have some 1510 Mesh- L WAPs that require an old version of code. I need 4.1.192.22M for those. Is it possible to bring up a 3rd controller running this old code with the other 2 4402's running modern code? What will break? I know that anchoring and mobility might get messed up. What are the other caveats?
View 2 Replies View RelatedWe have two Comcast 100MB routers. Can I plug these both into the SG200-50? How do I configure the ports?
I have an Apple Extreme Wireless Router that 30 Laptops use. I also have 25 VOIP phones and 10 Desktops that are on an unmanaged switch which I want to convert to the new SG200-50.
I'm using a Dell computer CPU i7 8 gig of ram. It is wired in to the router. Why does it take so long to log into the router and bring up the different pages in the settings. I have never seen a router take so long. I have not updated the firmware version 2.02NA. I have not upgraded it yet. oh I have a cable connection. When I surf the web the pages come-up fast.
View 13 Replies View RelatedToday i has tryed to update the firmware of my DIR-655 router, but in the screen under the administrative tools menu there is nothing to use.
how do I update the firmware and bring up all the necessary tools?Dir-655 works because they are connected to the internet and manages the wireless network.
I am trying to connect a 6509 switch to a 4503-E switch using single mode dark fiber over a distance of less than half a mile. Although a routine task, it does not work..We have a care 6509 switch where we concentrate all of our dark fiber connections for our remote sites. The 6509 switch already has 30 remote sites, most of them with 4503-E switches, connected in this way therefore it is a tested scenario. For the connections we use the GLC-LH-SM SFPs on both switches. Out of these 30 sites we had a similar problem with two of them, which we solved with the use of CWDM SFPs. With the CWDMs the fiber came up right away. However, I cannot keep using this solution because it is way too expensive! I had the losses of the fiber measured end-to-end and they are negligible (>0.5 dB).
In this latest case, like I said, we could not bring the connection up between the core 6509 switch and the 4503-E switch using the GLC-LH-SM SFPs. I then replaced the 4503-E switch with a 3560 and the link came up! Then I tried using a CWDM-SFP in the 4503-E, while keeping the GLC-LH-SM SFP in the 6509 and the link came alive again! Of course we already tried replacing the fiber patch cords with no luck. [code] I find it very weird for the link to work with the 3560 or with a CWDM in the 4503 but NOT with the SFP in the 4503!
I have two 3825's. Each has it's own ISP connection. Nat is configued for both. They have an ethernet connection between them and I'm running OSPF between the two so the routes propogate. I have qty 11 Dialer interfaces configured on each router (each router has an exact copy of the other routers dialer interface). However, I only want the Dialers up if the ISP connection on the mated router goes down. Much like HSRP I need one to preempt and be active if both ISP connections are up. When one goes down the other Dialers must come up. Each dialer sends a Dynamic DNS host name and IP address pair to DynDNS.org. So I cannot have both up otherwise the DNS names will bounce between ISP#1's IP address and ISP#2's IP address (back and forth). Let me know if any option exists to make this happen. As an aside the ISP's are providing me DHCP addresses so I cannot work off of an IP, it has to be the physical interface (i.e. Gi0/0).
View 1 Replies View RelatedI need WIFI inside a giant steel Quanset hut. There is a good signal right outside. Is there a way to do this with one device? I was wondering if I could put one of the antennas of a WRT54G through a hole to the outside and then set it in repeater mode. Theory being it would use the outside antenna to pickup the signal and the inside antenna to broadcast.
View 2 Replies View RelatedLinksys tried multiple WRT54g routers and access point, 192.168.1.1 can't open the router config page.
View 5 Replies View RelatedI found that Alternate LAN card will support.After replacing another LAN card i can ping all switches.But i want to know why my pc not pinging certain switches connected in network.Even i cleared the port security
View 5 Replies View Relatedmy system ip not able to ping by other system in my company network but my system is in the network and able to ping other system in the network my system IP have static IP and IP is pinging on by server
View 1 Replies View RelatedWe have recentrly replaced a 1700 router with Cisco 3945 router (Core Router) and the Channalised E1 interface is configured as given below: [code]
The issue happens intermittenly and makes network not reahable.Status of the links are UP/UP - No traffic forwarded through the link (Ser 0/0/0:1 and Ser 0/0/0:2) and at the same time not able to ping the local IP Address as well - 10.5.10.1/10.7.10.1.No issue on the Ser 0/0/0:0 link - Working fine.If you replace the new router with the old one all are working fine.
Here's my basic setup:
Computer A:
IP- 192.168.0.3
Mask- 255.255.252.0
Gateway- 192.168.0.2
[Code]....
Computer A can ping Firewall 1 and Firewall 2, but not Computer B. Computer B can ping Firewall 1 and Firewall 2, but not Computer A. Firewall 1 can ping Firewall 2, Computer A, and Computer B. Firewall 2 can ping Firewall 1, Computer A, and Computer B.
Why can't the computers ping each other, but their default gateways can? I've specifically allowed ICMP any any on all the affected interfaces.
Will this router ever see a firmware update so that we can have some additional functionality? The version of Twonky Media server that was bundled with this router was old to begin with, and now we are stuck with it? I tried the E4200 but it just kept spinning my drive that's parked in a ThermalTake BlackX, at least the 3000 doesn't do that, but when can we expect some new firmware, it's been 8 months. I used to love Linksys, but with this kind of support I may have to move to a different brand, and I bet I am not alone. it doesn't break the E3000 like you broke the 4200.
View 1 Replies View RelatedOne computer does not see the other through pinging...but somehow we are connected...strange i know. My confusion ( being network illerate ) is with the names and etc. and some terminologies ie ..client? host? I have found in the past when someone triesthey use words or areas that do not coincide with my system...which is laptop with win 7 prem and desktop XP sp3
View 2 Replies View RelatedI have 2 NIC cards on the same machine running Redhat 9.I need to setup the machine in such a way that both cards are in the same subnet but card on port eth1 can be reached through card on port eth0.I tried modifying the iptables (with the limited knowledge that I have on it,used google) and even tried turning it off.I also tried setting files /proc/sys/net/ipv4/ip_forward and /proc/sys/net/ipv4/conf/all/proxy_arp to 1 but was unable to ping from IP address on port 0 to IP address on port 1 and vice-versa
View 1 Replies View RelatedIf we have the following setup:Host A (IP :192.168.1.1, Prefix/length : 24, GW : 192.168.1.254) connected to the Router A on int Fa0/1 (IP : 192.168.1.254), Router A is connected to Router B, Host B (IP :192.168.2.1, Prefix/length : 24, GW : 192.168.2.254),connected to Router B on int Fa0/1 (IP : 192.168.2.254).Using the mentioned setup, after Host A pings Host B successfully, which entry will be in the ARP cache of Host A to support the transmission ?.
View 3 Replies View RelatedI have a cisco 2821 and have configured a llopback address which I want to use for management, however, I am unable to ping it from a device attached to GigabitEthernet0/0
View 1 Replies View RelatedI am getting RTO while pinging my L3 switch 3750 that happened after restarting switch,i have restarted it because I am not able to browse internet through URL,i am able to do it trough ip address, so I restarted it not I am getting RTO.
View 1 Replies View RelatedI will be moving away from my home computer but will still want access to it so I am trying to set up a VPN between it (home computer is windows 7) and my fedora 15 machine. They are currently on the same 192.168.1.0/24 network so I'm wondering if that may be the cause for my troubles.
Here's my setup:
Fedora 15 (192.168.1.3) is running the PPTP server with pptpd and gives 192.168.1.66 to any vpn client that connects to it./etc/pptpd.conf only has "localip 192.168.1.3" and "remoteip 192.168.1.66" options in it /etc/ppp/options.pptpd has "refuse-pap, refuse-chap, refuse-mschap, require-mschap-v2, require-mppe-128, proxyarp, lock, nobsdcomp, novj, novjccomp, nologfd, debug, dump" options Windows 7 (192.168.1.6, 192.168.1.66) is the client and I have it set to use connect to the public IP address of my router, PPTP, require encryption, only allow mschap-v2, don't use gateway in ipv4 properties.Both machines are connected to the same Belkin router (192.168.1.254) and I can ping locally to and from each computer no problem. The problem is my VPN connection is very inconsistent. I will open a ftp connection to 192.168.1.66 from 192.168.1.3, login, start uploading a file, get about 10MB uploaded, and then the VPN connection will die and the upload will fail. But, when I have "ping 192.168.1.66" running while uploading, the connection stays alive.
Lately I've noticed that my internet connection has been less than stellar. I will be playing an online game or surfing the web, and every so often I'll freeze up or things just won't run smoothly. My network consists of the following...All of my computers and devices connect to a Cisco 16 port gigabit switchThe switch then connects to a Peplink 20 Dual WAN routerThe router connects to a cable modem as well as a DSL modemThe other day I was trying to diagnose the problem, as well as update the firmware of the router. While I was on the main "status" page, I noticed an error saying that I couldn't connect to the router. It quickly cleared and everything was working fine. This of course made me think that my issues have to do with my connection to the router, and not with the internet service itself. I then tried ping -t to two other computers on the network, as well as the router. After 5 minutes of pinging, the connections to the two computers had zero fails, while the router connection failed about 5% of the time. I ran the same check from the other computers on the network, with similar results.So, I know that the issue lies with the router (I think), but that's where my brainstorm ends.
View 4 Replies View Relatedi can ping the other system but i can not access tthat system.. error message shows that path does not found.
View 6 Replies View RelatedI am able to ping the node but when i try to access the systm using backslash i am uable to access it and an error of host inaccessible.
View 1 Replies View RelatedI'm currently taking a networking course and was having some difficulty answering the following questions and could use a little clarification.Question: When pinging a non-existent device on your subnet, why doesn't the source node issue a ICMP echo request.My thoughts on this was because there was not a receiving node therefore any ICMP packets were not issued.Question 2: when pinging another non-existent device but not on your subnet, why doesn't the source node issue a ICMP echo request.
View 2 Replies View Related