D-Link DIR-825 :: Setup One IP To Bandwidth?

Aug 5, 2012

How do I setup one IP to throttle bandwidth?

View 1 Replies


ADVERTISEMENT

TP-Link 3G/3.75G Router :: MR3220 - Rules Setup Under Bandwidth Control / Does This Setting Shared By IP Range

Apr 2, 2013

Region : UnitedKingdom
Model : TL-MR3220
Hardware Version : V2
Firmware Version :
ISP :

Looking at the manual for this router in regards to bandwidth restrictions.When you set up the Rules under Bandwidth Control does this setting shared by the IP range or does each IP in the range get that amount of bandwidth?

View 1 Replies View Related

Setup Bandwidth Limiting / Qos?

Mar 13, 2012

I am a gamer living in my apartment with a room mate who loves to download music 24/7 and a girlfriend who loves to watch netflix. Needless to say, every time I go to play a video game I get shitty ping and lots of lag. From what I've gathered, DD-WRT's QOS is ****, and Tomato is the way to go in 3rd party firmware.

View 1 Replies View Related

Solarwinds Bandwidth Monitor Setup?

Aug 10, 2012

I came across some free bandwidth monitoring software by Solarwinds while doing some reading on other sites. I installed the software and now im stuck at setup. The Softaware is asking for...

Ip Address/Hostname
SNMP Version
Community string

I'm assuming the IP Address/Hostname would be my computers IPv4 on the network and as far as the SNMP Version goes im not sure, I can either choose from SNMP v1/2c or v3. For the community string, I'm assuming its Public but im not completely sure.When I attempt to go to the next step is says the credentials test failed So obviously something I entered is incorrect.

Note: this is on my own home network. Im using a Comcast all in one router and modem.

View 1 Replies View Related

Cisco WAN :: 2811 / Setup Bandwidth On Border Router Or ASA Pix?

Jan 6, 2011

I got connected ASA ----- ROUTER 2811) to metroethernet switch from my ISP , with a 4MB of bandwidth but the internet connections to all my LAN has been frozen and we lost connection to the internet, to restart the internet service I need to boot the ROUTER 2811 - and ISP switch to rollback the internet operation,My ISP support tell me if is possible to set up the traffic bandwidth in one or  both borders devices,  ( ASA 5510 or ROUTER 2811)

View 3 Replies View Related

Cisco Routers :: RV042 Setup To Grant HTTP Traffic Minimum Bandwidth?

Jul 24, 2011

I am trying to set up my router to grant http traffic a minimum bandwidth of - for example - 5,000 kBit (if there is any http traffic).
 
So I set http min. rate to 5,000 while I set nntp min. rate to 1 However, when I run nntp downloads on several connections (e.g. 10) my single http download never goes above 1,000 kBit. Without any other connections I reach 8,000 kBit.

I am using a single 12 MBit line.

View 4 Replies View Related

Cisco WAN :: Aironet 1240AG - Setup Guest Network That Is Secure And Limited In Bandwidth Utilization?

Jan 27, 2013

I have a Cisco Aironet 1240AG Access Point and I am trying to setup a guest network that is secure and limited in bandwidth utilization. I see an option under security > SSID Manager on the web interface to select an interface of Radio0-802.11G, Radio1-802.11A or both. Can I put the guest network on the Radio1-802.11A and make it more secure/bandwidth limited or does this option not matter?

View 3 Replies View Related

D-Link DIR-655 :: Way To Set Bandwidth Control

Jun 30, 2010

I have several computers connected to the network, can I restrict the download bandwidth on specific computer?

View 3 Replies View Related

D-Link DIR-615 :: Can Bandwidth Be Distributed Evenly

Oct 17, 2011

I just purchased a Dlink DSL-2750U today which I am using with my ADSL connection. I have three wired computers using this connection and no wireless systems at the moment. I would like to know if it's possible to share the bandwidth evenly amongst these three computers? The other two computers are hogging on the bandwidth leaving me with barely anything to work with.

View 6 Replies View Related

D-Link DIR-600 :: Limit Bandwidth On Router?

Jul 12, 2011

How can I limit the bandwidth of a router (DIR 600).

View 1 Replies View Related

D-Link DIR-655 :: How To Decrease Bandwidth Connection

Mar 3, 2013

I would like to know if it is possible in dir655 ver  1.30 to limit bandwith in QoS using mac address?because in QoS Engine Name i can only see this opt. no opt for MAC, what if the user use DHCP?

View 1 Replies View Related

Calculate Aggregate Bandwidth Of MPLS Link?

Jul 22, 2011

How to calculate aggregate bandwidth of MPLS link. Is there any tool available for the same.

View 3 Replies View Related

D-Link DIR-601 :: Throttling Bandwidth For Specific Devices?

May 16, 2011

Bought a DIR-601 for my sister and her kids for their home.  Setup and works successfully.  Sis asked if there is a way to give her laptop bandwith priority over the kids devices.  As is, they are all sharing limited DSL bandwidth.  Reading the manual, I see the QOS feature for specific types of traffic, and other limiters and schedules to shut out certain MAC addresses entirely.  But wondering if this throttling feature exists in the router also.

View 11 Replies View Related

D-Link DIR-655 :: Bandwidth Limited Guest Zone?

Apr 28, 2011

I'm wondering if there is a way to prioritize traffic on the router's main WiFi over the guest zone or if there is a way to limit the bandwidth on the guest zone.

Ideally, I'd like to keep a locked primary WiFi for high-speed usage (I know, nothing it really ever secure) and an open guest zone for low-speed usage to whomever wants it. As far as I can tell, the DIR-655 doesn't support this kind of configuration.

View 2 Replies View Related

D-Link DIR-825 :: Increased Bandwidth But Slowing Down Speed

Mar 7, 2013

i just increased my band width from my provider to 50 down ..3 up  ..I can get almost the 3 up while connected to my d link but only about 2.5 down ..when i bypass my d link i get mid 40's  down and 2.8 up .. for some reason my d link is slowing down my speed . I have a DIR825  hardwear B1   Ferm wear 2.07 NA

View 5 Replies View Related

D-Link DIR-655 :: Settings To Limit Bandwidth From Router?

Jun 11, 2011

I just purchased a 100M fiber line to go with a brand new D-Link DIR-655 router. Before plugging in the router, I tested on my laptop directly from the modem and had great result speeds of 98M/97M. I connected the router, then plugged my laptop to find I was only getting speeds of about 10M/6M. This was true for both wired and wireless connections.

I took a look at the router settings. I turned off QoS, but that didn't work. One thing I did see was the WAN was set to auto. I attempted to change that to 100mbps or to 1000mpbs. However, when I did that my modem light that shows a 100M connection is active turned off and I couldn't get internet. I was only able to get a connection if I left that on auto. Is there a setting somewhere that is limiting my bandwidth from the router?I reset the router twice and checked to find I had the latest firmware. Is there something that I am missing? I have always been a Linksys fan, but wanted to see how D-Link is.

View 7 Replies View Related

D-Link DIR-655 :: ITunes Killing Bandwidth How To Control It

Apr 5, 2011

This has finally become a BIG problem. Any time I have iTunes running and downloading podcasts, it hogs all the bandwidth for the Internet (but not the local network). This is not only slowing down access from the machine running iTunes and the downloads but for every other device trying to web browse.I'm running two Macs and one Windows/Dell PC on the network. All are hard-wired (Ethernet) to the DIR-655. How to throttle iTunes? I did some research and found that I am apparently not the only one having this issue.I'm about to bail on iTunes entirely and try to get used to Miro, which does allow bandwidth control.

View 3 Replies View Related

D-Link DSL 2640B - Does It Load Balance Bandwidth

Aug 30, 2011

I have a D-Link DSL 2640B on the way which I plan on using to replace my 2Wire modem. The 2640B is a combination of a modem/wireless device. Does it dynamically load balances the internet connection? Sometimes while I'm playing online games on my PC and a few others are using the internet for browsing or Youtube, I lag A LOT. Latency shoots up from 10 to 200. QoS goes to ****. And I only need 0.50-1Mbps to keep a steady online play. This was the problem with my 2Wire. So does the 2640B load balance the bandwidth?our max speed is 3.5Mbps according to the ATT Rep.

View 10 Replies View Related

TP-Link 300Mbps Wireless :: How To Control Bandwidth In WE941ND

Nov 17, 2012

Region : UnitedArabEmirates
Model : TL-WR941ND
Hardware Version : Not Clear
Firmware Version : 3.13.9 Build 120201 Rel.54965n
ISP : etisalat.ae

How to controller wireless bandwidth in WE941ND.

View 5 Replies View Related

D-Link DIR-655 :: Playon Online Bandwidth Showing Slow

Jun 14, 2011

I have playon and the online bandwidth is showing slow. I did speedtest and it shows 20mbps, but the playon says below 2.  No windows (7) security is enabled and avast is turned off. i rebooted and get the same results.I also cannot do any updates for my windows 7. I try and it says that it cannot do the update. I check the logs and all of the updates were done fine up to when I installed the 655; now it doesn't work.

Playon support says check network, which I have done, and the only thing left is the 655.

View 9 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8968 Priority On Bandwidth Control

Feb 7, 2013

Region : Spain
Model : TD-W8968
Hardware Version : V1
Firmware Version :

I have a TD-W8970. In settings "Bandwidth Manager" there is an option to put a value between 1 and 8, but does not specify which is better (1 or 8). What the value to give more priority to a computer to another?

View 1 Replies View Related

D-Link DIR-655 :: Stop Apps Like Internet Download Manager From Choking Bandwidth?

Jul 22, 2012

My younger brother uses IDM to download files and it slows my Internet down to a crawl. I've tried reasoning with him but its not getting through to him. Is there any way I can use my router (bcz only I have access to it) to limit IDM?

View 5 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8968 / FTP Does Not Work After Bandwidth Control Enabled

Mar 7, 2013

Region : India
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
ISP : MTNL

After lot of troubleshooting and efforts I figured out there seems to be BUG with routers firmware 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n.When you enable Bandwidth control, FTP stops working from Internet. However, it does work from local network. When you disable Bandwidth control, FTP starts working from internet as well as local network.

View 1 Replies View Related

TP-Link 300Mbps Wireless :: TL-WR841ND - LAN Freezes With High Bandwidth Usage

Jan 13, 2013

Region : Romania
Model : TL-WR841ND
Hardware Version :
Firmware Version : 3.13.27 Build 121101 Rel.38183n
ISP : cosmote

hardware version is WR841N v8.wireless works just fine. i use it for my smartphone and an old laptop. i use ethernet cable to connect to main computer where all is ok until i start using my bit torrent client. as soon as i build up traffic above 1MB the ethernet portion of the router freezes and needs a reboot. when frozen, wireless is still working and i still have access on the lan to the router via my browser. i got this router so i could have wifi for my phone. my old router (asus rx3041) worked just fine and i accessed my isp at the maximum speeds it would allow on a 60 gigabit connection.

View 9 Replies View Related

TP-Link Dual-Band Wireless :: TL-WDR4300 Bandwidth Slow Down When Router Plugged In

Feb 24, 2013

Region : Canada
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.17 Build 120426 Rel.29216n
ISP : Bell Canada

Just had my line upgraded to 50mbit down, and 10mbit up. Whenever the router is between the PC and the modem, my speeds drop to 30mbit. If i plug directly into the modem, I get the full 50Mbit. Upload speeds are always 10mbit.I've tried power cycling devices, and even replaced all cables with cat6 (which I know isn't the issue, but i'm just trying to eliminate everything)

View 6 Replies View Related

Cisco Switches :: SG200 Switch To Allocate Bandwidth On 100 Mbps Fiber Internet Up-link

Jan 21, 2012

I'd like to use an SG200 swicth to allocate bandwidth on a 100 Mbps fiber Internet uplink.I will have 5 routers (each supporting a separate network) connected to the SG200, and I'd like to give each network 20 Mbps. QOS configuration, best CIR and CBS settings for this.

View 1 Replies View Related

Bandwidth Test For 1 Mbps Bandwidth Line?

Sep 9, 2011

We have 1 mpbs bandwidth line, but most of the time we are getting only 300-500 kpbs download speed, i want to send statistics report to our ISP, what will be best procedure to test the bandwidth report, i have checked in some websites like bandwidthplace and speedtest but these sites are not accurate, how to check the actual bandwidth we getting from ISP against 1 Mbps. We have solarwinds monitoring tool in this i have configured the WAN interface for 1 mbps

View 5 Replies View Related

D-Link DIR-825 :: Setup HMA In DD-WRT?

Jun 12, 2011

I own a D-Link DIR-825, hardware revision B1, which I last night flashed to DD-WRT, DD-WRT v24-sp2 (08/07/10) std, (SVN revision 14896), as per the WIKI page for my router on DD-WRT site.

I followed various tutorials to configure the settings in DD-WRT and my Internet on ISP IP address is flawless.  However, I am having trouble getting the VPN settings into router pages.  I want my entire WLAN/LAN to be able to use VPN direct via the router.

see my applicable screenshots from DD-WRT.  I have deleted my password on the second screenshot to protect my account.  As you can see on the last screen, I am not getting any message under the "state" and "log" windows as should be received if the VPN connected successfully.

NOTE: I have posted this on DD-WRT, HideMyA**, and D-Link forums to maximize my exposure and try to get a solution quickly.  My intent is NOT to "spam". 

View 1 Replies View Related

How To Setup Link Aggregation

Jul 23, 2011

I am trying to setup a home network where I have multiple low bandwidth or rather lower bandwidth links coming in. They are suppose to be broadband but I do feel the need for a fatter pipe. Since this is in India and we have limited availability of bandwidth options like here in the US I thought if I could double or even get close to doubling my bandwidth using some sort of device for link aggregation or a network / pc setup which can achieve thisThe links I am getting are above 1mbps, possibly even 2mpbs and its relatively cheap, 100$/yr so I can add 3-4 to get desired results. A dedicated 10mbps connection costs nearly 12000$/yr so I have a lot of margin to create a substantial pipe without the cost if what I am thinking is possible.

View 4 Replies View Related

D-Link DIR-825 :: Setup Download Available?

Jan 18, 2012

I'm attempting to set up a DIR 825 and I have a damaged setup disc.Is this available as a download?

View 3 Replies View Related

D-Link DIR-655 :: How To Setup This Device

Jan 2, 2013

Here's the situation, 2 houses, house #1 has internet, DIR-665 connected to Cable modem, between the 2 houses CAT 6 cable, house #2 has DIR-655. Both houses need to offer wireless. How should the DIR-655 (house#2) be set up? (SSID/DHCP/UPNP/IP/GATEWAY/SUBNET, etc)?

View 1 Replies View Related

D-Link DIR-825 :: Setup CD Required / Necessary?

Jul 28, 2012

I have a DIR-825 coming. Do I really need that long to setup something? When I got my Netgear all I did was plug the sucker in. Two ethernet cables in the back. Done. Later on I added a wireless device in the living room so I setup a name and key. Done.I still have the same devices, except going to add my Girlfriends Daughter and QOS her bandwidth.

View 1 Replies View Related

Getting TP-Link Universal Repeater Setup?

Mar 22, 2012

facing issues with TP-Link TL-WA801ND while setting it up as a Universal repeater.The AP is a Linksys E3200..and I got the TP-Link to broaden my WiFi at home, I was successful in setting it up, however, after a day or two I get prompted to enter a "WPA2 Enterprise" username/password.I DID NOT setup WPA2 Enterprise, mine is WPA2 Personal...it's peculiar that it works for a bit then reverts to Enterprise.

View -1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved