D-Link DIR-601 :: Throttling Bandwidth For Specific Devices?
May 16, 2011
Bought a DIR-601 for my sister and her kids for their home. Setup and works successfully. Sis asked if there is a way to give her laptop bandwith priority over the kids devices. As is, they are all sharing limited DSL bandwidth. Reading the manual, I see the QOS feature for specific types of traffic, and other limiters and schedules to shut out certain MAC addresses entirely. But wondering if this throttling feature exists in the router also.
View 11 Replies
ADVERTISEMENT
Feb 1, 2013
I have a Linksys WRT54GS router that I have installed dd-wrt on.My household is overloaded with wireless devices, and living in a home of 6, speeds for everyone seem to slow down drastically later at night when everyone is simultaneously connected and streaming media -- whether it be Netflix, YouTube, etc.. My typical speed wired to the router with no other connections is around 25 mb/s down and 1-2 mb/s up.Obviously, it's going to slow to a crawl when we have an iPad, 3 iPod touches, an iPhone, a Wii (playing Netflix) and 4 PCs all connected simultaneously.What I need to do is give my personal computer priority and throttle all other devices. So that I myself will have decent speeds while hampering all of the other household connections. I rely on those speeds for my job and that should have priority over my brother watching music videos on YouTube.
View 1 Replies
View Related
Jun 11, 2011
Long story short, the Westell wi-fi DSL modem router box that came with the the service craps out every couple days. I bought a new Acrtiontec GT701D to replace it and installed it in bridge mode. The Actiontec works great for a few days, much better than the verizon POS, then the bandwidth gets throttled down to a meg per second.
Do I need to tell Verizon I have a new DSL modem?
View 1 Replies
View Related
Sep 29, 2012
I think that my ISP is throttling my bandwidth at the modem . how access full available bandwidth.When the technician installed the fibre optic line and then the modem, he showed me an amazing 77MB/s (about 600Mbps) before the modem!!But after the technician left these were the test results after the router:
1) SpeedTests.net:
averages, after router, show: UP between 56/60Mbps & DN 45/75Mbps
2)Local Server Speed Test:
average: UP 45Mpbs & DN 170Mbps
A Japanese Internet savvy guy explained that NTT East throttles the available bandwidth at the building by specific apartment/modem settings related to individual contract bundles. I signed up for the top bundle: TV, Phone and Internet connections.This is my Hardware/ software setup:
OS: Win7,
Line specs:
Line type: IEC60874-14
Connector type: SC
Core across: 9 micrometers
Clad across: 125 micrometers
ITU-TG-652
NTT East fibreoptic TV/Internet/Telephone bundle (100Mbps best effort) Hikari Next Family Type but 10Mbps is considered within parameters
Asahi ISP Internet contract
Modem:
GE-PON (WAN+Coaxial TV antenna)
"SCM-GE-PON-<H>A GV-ONU D<1>" model
Router:
RT-S300HI (4 Giga ports + 1 phone)
Router & Modem have Japanese firmware which I cannot understand and, according to the NTT East, I must rent both modem and router from them and "will not support any other modem/router setup".I could not understand if it was because of technical or contractual limits.
I have tried to test my throughput after the modem but I could not figure out where the DNS, IP, WAN etc strings of numbers should go and, in the end, I simply cannot connect to the internet from my laptop directly to the modem so I cannot perform the same speed tests after the modem.
View 12 Replies
View Related
Nov 18, 2012
How can I restrict wireless access to specific devices? Ideally, I would like to turn the access off and on to restrict my children's usage when we're not around or when they try to sneak on during the night.
View 5 Replies
View Related
Aug 21, 2011
We will shortly be installing a Cisco 3825 router, to be connected to the BTNet service, over fibre.We will be binding many public IP addresses to the router.
Is there a way of defining a specific bandwidth limit per IP address, or range?
View 5 Replies
View Related
Feb 22, 2013
I have a cisco 2821 router where as a cisco 2960 switch with connect on router as a trunk & one user vlan . this is my WAN router all traffic are internal . i have 2MB data connectivity on my WAN side. i have to Give a specific Bandwith on my SAP traffice . like when SAP traffice will come they all time get around 50 % bandwidth of my channel. If SAP resuest are not comming then other traffice will get full bandwith .
View 4 Replies
View Related
Jan 24, 2013
configuring a switch or a router to limit the bandwidth for a specific user/IP when need it. Most of my remote offices are configured like this:
Users ------ 3560 switch ------- 2801 router -------- T1 to NOC -------- 7204 router with channelized DS3
I use Netflow Analyzer for high bandwidth usage alerts and can see the user's IP right away when someone is clogging our T1s. My goal is to be able to temporarily limit the bandwidth of the user taking over the T1. Whatever is best switch config or on the router.
View 2 Replies
View Related
Nov 12, 2012
I have a cisco router 881 with advipservices running ios Version 15.2(4)M1 this router is a device that the user will connect company equipement with antivirus and such.is there a way I can force the ports like fe0 fe1 2 3 to accept only devices with specific mac addresses?if not, is there a way for me to apply an acl to vlanX to block everything that's not from these specific addresses?
View 4 Replies
View Related
Mar 18, 2012
I've been having a bit of a problem lately trying to play Battlefield 3 on my PS3 when other computers are running on my network.
I'm looking for a program or method to set bandwidth limits on some devices to try to guarantee the PS3 enough bandwidth to play without lagging.
With the research I have done what I can find is that there is something called Quality of Service (QoS), and traffic shaping -- which are good and fine but I don't believe my Westell router supports them and I don't want to have to do anything crazy with my router.
Also I am currently dual booting Ubuntu Linux alongside Windows XP, and I don't have XP set up because I want to install Windows 7 on that partition once I can read DVDs (in the hardware forum), therefor I would really like to find a Linux program that I can use to shape my network traffic.
View 2 Replies
View Related
Jan 13, 2013
limit the bandwidth used by certain wireless devices on my network. The problem I'm having is of priority. For some reason when someone is watching Netflix on my laptop (wireless) no other device has any bandwith available to it, so while someone is watching Netflix my hard wired desktop can barely load Google.com much less do anything useful.I'm using a Cisco ValetPlus M20 wireless N router.allocating at least a minimum amount of bandwidth to wired devices?
View 1 Replies
View Related
May 18, 2012
I'm looking for a wireless router that can throttle per device. That is, a specific internal IP address can have a specific upload/download speed limit assigned to it that the device cannot exceed. I'm not looking to allocate bandwidth priority or block a specific protocol.
View 1 Replies
View Related
Apr 17, 2013
Although this is not a common issue, we have experienced occasions where our internet utilization has been maxed out (slowing everyone else down). Utilizing some features in the ASA, such as Top Usage Stats, along with PRTG monitoring, have always tracked the culprit down to being a single user -- be it someone downloading movies to a portable device, or downloading ISO's. (And for some strange reason it seems to always be a wireless user.) We are using an ASA 5510 for our firewall, and I was wondering if its possible to prevent a single client from consuming a disproportionally large percentage of our internet bandwidth? If the ASA 5510 doesn't have the ability to do this on it's own, are there any recommendations for add-on solutions?
View 1 Replies
View Related
Apr 11, 2012
We have 110mbps internet service. When we have the 5505 behind the cable modem, our speed drops to 55mbps or so. If we remove the 5505, we see the full 100mbps. I assume the 5505 can handle the speed; if so, what other things should I be looking at?As an aside, we used to have 50mbps wich worked fine, then the ISP upgraded to 60mbps and the through put dropped to 30mbps (It always seems to be half)
View 2 Replies
View Related
Mar 7, 2011
When I am connected directly to my Surfboard modem I get 3000kbps upload with wired connection.
With the BEFSR81Router conected I get 1000kbps.
View 9 Replies
View Related
Jul 1, 2012
Is it possible to enable an absolute value rate limit using QOS on a HP ProCurve 5406 switch for a particular IP range on a specific port? Is there a way to configure our HP 5406 with an absolute rate limit on "WAN" port for that server's IP range? I would like to limit it to only being capable of sending 1Mbps worth of traffic over the head end at once.Everything in the documentation points towards priority queues, which as far as I can tell, isn't really what I want.Baring accomplishing this goal using rate limiting is there a better way to prevent our services from accidentally saturating this connection?i thimkong about somthing like that:
class ipv4 rate-limit-port-A1
match ip 10.136.0.0/16 any
exit
policy qos port-a1-ratelimit
class servers-to-be-slowed action rate-limit kbps 1000
exit
interface A1 service-policy port-a1-ratelimit inI'm not sure about this.
View 4 Replies
View Related
Oct 25, 2011
I use a router RV082 with load balancing. My problem is when I try to access a specific site, I get the error message that my IP address changes and I can not use 2 ip address. I want to specify an ip range to always use the same WAN port.
View 2 Replies
View Related
May 16, 2013
In Setup > Parental Control it is possible to set rules attached to specific website URLs. I want to block access from 1am to 6am.
However these rules only apply to websites URL. Is there a way to apply a rule to ALL websites at once? I tried to enter "*" or "*.*" in website URL field but it doesn't work.
View 1 Replies
View Related
Apr 1, 2013
Is it possible to deny all access except specific IP's to a service on a Dlink DIR-655 ?Say a web server on port 1234.The allowed IP's are not in a range.
View 1 Replies
View Related
Apr 28, 2011
Is there a way to block specific computers on the LAN from specific web sites by the domain name? All I can see is that if I put, for example, www.facebook.com, it will be blocked from all computers on the LAN, whereas if I want to block only 192.168.1.3 for example, I have to use the IP address through the Access Control, which is much harder and ****e to some "work around" by the user.
View 3 Replies
View Related
Oct 5, 2011
How to configure the 825 to block inbound traffic from a specific internet IP address ?i noticed an IP and MAC that i don't recognize that is listed as a connection to my NAS's media server ...i blocked it in the NAS configuration page, but i don't want any unsolicited traffic into my network.
View 3 Replies
View Related
May 24, 2011
ASA 5520 running 8.0.4
ASDM v.6.1
Need assistance understanding how in ASDM/Configuration/Site-to-Site VPN/Connection Profiles/ "Any Entry" I can specify that I only want to offer an IKE Proposal of pre-share-aes-256-sha?
The IKE Proposal field has a number of possible options including: pre-share-aes-256-md5, pre-share-3des-md5, pre-share-aes-256-sha, pre-share-aes-192-sha, pre-share-3des-md5, pre-share-aes-sha and pre-share-3des-sha.
I am able to pick a specific IPSec Proposal w/o issue but when I attempt to do the same for the IKE Proposal, and click OK the choice does not "stick" but rather returns to the entire list as defined above.
View 2 Replies
View Related
Jan 9, 2013
I have a DIR-655 that I have been using for a while (b1 revision). and suddenly I noticed my wifi speed fluctuates constantly. My lenovo Y580 sees speed drop to 130 immediately and then it can slowly progress to 1 Mbps until the hardware is all rebooted. Same happens to my Nexus 7, Dell XPS M1530 and to my roku. I have updated to 2.07 (since 2.10 is advised to avoid). And I have attempted changing channels or factory refresh.What Firmware version is currently loaded? 2.07What region are you located?
What ISP Service do you have? Cable or DSL? Cable (link speed independent of internet speed)What ISP Modem do you have? Stand Alone or built in router? Separate Motorola ((link speed independent of modem)What ISP Modem make and model do you have? Does not matter, router issue.If this modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems.To tell if the modem is bridged or not, look at the routers web page, Status/Device Info/Wan Section, if there is a 192.168.0.# address in the WAN IP address field, then the modem is not bridged. Not bridged
Turn off all anti virus and firewall programs on PC while testing. 3rd party firewalls are not generally needed when using routers as they are effective on blocking malicious inbound traffic. Independent of issue, not a factor
Turn off all devices accept for one wired PC while testing. Wired works perfect.Check cable between Modem and Router, swap out to be sure. Cat6 is recommended. Wireless issue.
View 6 Replies
View Related
Dec 29, 2012
]Region : Philippines
Model : TL-MR3220
Hardware Version : V2
Firmware Version : 3.14.2
ISP : globe telecomms inc.
i just bought an antenna for my new tl-mr3220 v2 router that is 9db. my current one is he 5db that was supplied together wit the unit. then when i installed the new antenna, instead of an increase in the range it lower than my old one. is there any specific antenna or type that you can use? if so what types of antennas?
View 2 Replies
View Related
Sep 21, 2012
Yesterday (Friday, September 21, 2012), my Internet connection started acting up. After some testing, I confirmed a very specific and baffling set of symptoms: Internet connection goes away every 25-35 minutes (I did not confirm the exact interval, but it seems to be about 30 mins.)Only some protocols are affected; HTTP*, P2P, etc. stop working; FTP, etc. continue to work When it’s stopped, cannot even ping router or cable-modem IPs or view their firmware pages Domain-names and IPs are irrelevant (for protocols that stop working, neither work, for those that still work, both work)Resetting router fixes it for another 30 minutes Keeping the connection idle or active doesn’t seem to make a difference (nor the bandwidth usage in that period)Connecting directly to cable-modem allows it to work indefinitely Disconnecting the router from the cable-modem works indefinitely (no Internet connection obviously, but can still access router IP and firmware page)Connecting the router to the cable-modem, but putting the modem on standby also works indefinitelySame problem with both a wireless laptop and wired (on any port) desktop (both Windows 7; will try to test Windows XP when possible)Nothing had changed in the days leading up to the issue. No modifications to the networking configuration or the router; there were not even any Windows updates except for an MSSE definition update.Waiting does not fix it, nor does any amount of fiddling with anything; only resetting the router fixes it for 30 minutes (resetting the cable-modem doesn't work either)if I keep pressing the standby button on the cablemodem after browsing some pages, the connection works indefinitely (If I press the button to restore the connection, browse some pages, press the button again to cut the connection, it works fine for hours and hours without issue. Only when I leave it active for a while does it finally stop. I repeated this for three days with the same results.)I tried cleaning the pins in the router’s plugs, but that didn’t work, which was not really a surprise since I was not getting a lost connection error.
Obviously my first thought was that the router was having a problem, and this is borne out by some tests. The problem is that when it drops, it is not a full drop since I can still do things like ftp ftp.mcafee.com and such which means that the connection and DNS are still working. Moreover, if it were the router, then why does it stay alive indefinitely when not connected to the cable-modem (i.e., no outside influence)?
The problem doesn't seem to be either the cable-modem nor the router, but rather an interaction between the two, like something from the outside (port scan? hacker? ISP?) that is triggering a problem in the router. I see that there have been a couple of vulnerabilities for the DI-524, but those were a while back and should be fixed since I have the last firmware for it.
I don’t think it’s my ISP (Rogers) since I have been using the router for several years without problem and can connect indefinitely when bypassing it. But I can’t rule them out since that is one of the only possible things that could have suddenly changed.
(I note that when I opened the router, I heard a very high-pitched noise from somewhere near the capacitors/ferrite ring which I don’t think I heard the last time I opened it a few years ago, but then if it were that, then why would it affect only a very small, specific set of functions?)
Update:Last week, my Internet connection dropped out for two days. I called the ISP and they had me bring the cable-modem in to be replaced. I exchanged the SB5100 for a new cable-modem that has a built-in router with wireless AP and firewall. (I left it in gateway mode instead of bridge mode.)This morning it started behaving just like the old router. Most protocols continued to work (mail, P2P, NTP, etc.) but web-browsing (HTTP) was dead; I could not even connect to the cable-router’s web-interface. I rebooted the cable-router and HTTP functionality was restored; exactly like the previous router.
I find it highly unlikely that this could be a coincidence or related to the router itself since the new one is literally brand-spanking-new (bagged, twist-ties, in a box, with that new-plastic smell, etc.), and completely different from the old one (the new one is an ISP-branded model labeled “Hitron” while the old one was a D-Link DI-524).
View 1 Replies
View Related
Dec 18, 2012
I have a Router 2801 with the run conf :
!
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.1.1 192.168.1.63
ip dhcp excluded-address 192.168.1.192 192.168.1.254
!
[code]....
I want to assign a specific IP to a specifig host by MAC .. for example i want the ip 192.168.1.10 to be assign to the host "client1" by mac.I've been creating a new dhcp pool static:
!
ip dhcp pool static
host 192.168.1.10 255.255.255.0
hardware-address xxxx.xxxx.xxxx
client-name client1
!
but the "client1" is still taking other ip.
View 10 Replies
View Related
Mar 3, 2011
Using a DIR-655, does anybody know how to create a firewall rule to block all dns requests except to specific servers?
View 2 Replies
View Related
Jan 9, 2012
My 655 router (RevB, Firmware 2.03) is connected from one side to a DSL modem and on the side to two wired PC's and via wi-fi to several other wireless clients (two smart phones and two notebooks). All is well until I try to connect a specific notebook. Connection is estabished for about 30sec and then the router drops ALL connections (including internet and local network!) and I must re-start him by un-plugging from power. This phenomena is specific to a specific notebook since with the other one
View 7 Replies
View Related
Jun 30, 2010
I have several computers connected to the network, can I restrict the download bandwidth on specific computer?
View 3 Replies
View Related
Aug 5, 2012
How do I setup one IP to throttle bandwidth?
View 1 Replies
View Related
Oct 17, 2011
I just purchased a Dlink DSL-2750U today which I am using with my ADSL connection. I have three wired computers using this connection and no wireless systems at the moment. I would like to know if it's possible to share the bandwidth evenly amongst these three computers? The other two computers are hogging on the bandwidth leaving me with barely anything to work with.
View 6 Replies
View Related
Jul 12, 2011
How can I limit the bandwidth of a router (DIR 600).
View 1 Replies
View Related
Mar 3, 2013
I would like to know if it is possible in dir655 ver 1.30 to limit bandwith in QoS using mac address?because in QoS Engine Name i can only see this opt. no opt for MAC, what if the user use DHCP?
View 1 Replies
View Related
