We will shortly be installing a Cisco 3825 router, to be connected to the BTNet service, over fibre.We will be binding many public IP addresses to the router.
Is there a way of defining a specific bandwidth limit per IP address, or range?
I have a cisco 2821 router where as a cisco 2960 switch with connect on router as a trunk & one user vlan . this is my WAN router all traffic are internal . i have 2MB data connectivity on my WAN side. i have to Give a specific Bandwith on my SAP traffice . like when SAP traffice will come they all time get around 50 % bandwidth of my channel. If SAP resuest are not comming then other traffice will get full bandwith .
View 4 Replies View Relatedconfiguring a switch or a router to limit the bandwidth for a specific user/IP when need it. Most of my remote offices are configured like this:
Users ------ 3560 switch ------- 2801 router -------- T1 to NOC -------- 7204 router with channelized DS3
I use Netflow Analyzer for high bandwidth usage alerts and can see the user's IP right away when someone is clogging our T1s. My goal is to be able to temporarily limit the bandwidth of the user taking over the T1. Whatever is best switch config or on the router.
I want to limit data consumed by one of my devices; how can I do that. I have set up wireless network using Belkin AC 1200 DB.
View 1 Replies View RelatedBeen looking around in my routers settings for something that even comes close to limiting bandwidth on a specific port, or mac address, but the only thing I can find is priority settings like "Low, Normal, High, and Highest" I did however see this:
I am not 100% sure if I can specifically set bandwidth limit per port or mac address, cause I don't see an option to do that, so I presume it just limits the whole network as one...
Is it possible to enable an absolute value rate limit using QOS on a HP ProCurve 5406 switch for a particular IP range on a specific port? Is there a way to configure our HP 5406 with an absolute rate limit on "WAN" port for that server's IP range? I would like to limit it to only being capable of sending 1Mbps worth of traffic over the head end at once.Everything in the documentation points towards priority queues, which as far as I can tell, isn't really what I want.Baring accomplishing this goal using rate limiting is there a better way to prevent our services from accidentally saturating this connection?i thimkong about somthing like that:
class ipv4 rate-limit-port-A1
match ip 10.136.0.0/16 any
exit
policy qos port-a1-ratelimit
class servers-to-be-slowed action rate-limit kbps 1000
exit
interface A1 service-policy port-a1-ratelimit inI'm not sure about this.
I am planning to buy a router for my hotel and I would like to know is it possible to limit the bandwidth limit to the guests? And the admin computer can utilize the maximum speed? it it possible to create a login page paper when some one enters my wifi connection?
View 7 Replies View RelatedI use a router RV082 with load balancing. My problem is when I try to access a specific site, I get the error message that my IP address changes and I can not use 2 ip address. I want to specify an ip range to always use the same WAN port.
View 2 Replies View RelatedWe have a new 100MB internet service, but we only pay for 10MB and above that is a per/MB fee and not cheap. I want to limit all traffic inbound and outbound only to use up to 10MB on the outside interface of our Cisco 3825.
View 9 Replies View RelatedOn my country, international bandwidth still expensive. I want to split local and international bandwidth and limit inbound and outbound bandwidth for each ip like this:
IP 10.100.10.11 can use 100Mbps local bandwidth, 1Mbps international bandwidth
IP 10.100.10.12 can use 100Mbps local bandwidth, 2Mbps international bandwidth
I want to use
Router 3825Switch 2960
NB: I have online one internet line.
Was the above equipment can perform functions that I want or need any additional equipment? And Should i use 2 line to achieve my goal?
I have five computers in my shop., and I have 2 Mb speed of Internet connection. want to split internet speed equally for every computer.
View 1 Replies View RelatedI am a Network admin of 200 Computers.Most of our users used to download movies through torrents.I just want to now how can i limit the bandwidth for specific user for both domain and work group user
View 4 Replies View RelatedIs there a way to limit a whole PC windows XP, or a certain program to use only a certain about of your total internet connection bandwidth?For example, I have 5 PCs in home all one the same ISP connection. I have one PC that I am trying to backup files online but I can only run it at certain times due to the backup program using ALL upload/download speed. And that makes every other PC super slow.
View 3 Replies View RelatedIf a person downloads via ADSL2 5 GB how much bandwith would this require?
View 1 Replies View RelatedI am using ASA 5505 cisco firewall as a transparent firewall. I have assigned ethernet 0/0 as outside interface and ethernet0/1-7 as inside interface. There are 3 departments in office. So, i connected ethernet 0/1 to Dept A, ethernet 0/2 to Dept B and ethernet 0/3 to Dept C. Now, I want to limit bandwidth to each department, e.g, 1 Mbps download/upload to Dept A, 512 kbps download/upload to Dept B and 512 kbps download/upload to Dept C. So, how can i do this in ASA 5505.?
View 1 Replies View RelatedIf two (one 6509A 9/26 with server A located in A end, 6509B with serverB located in B End) which is connected via a 1G link. If there is serverA send 700M file to server B via a 1G link. If I configured below command to 6509A 9/26, can I limit the bandwidth of server on bothincoming and outgoing to 500M?
class-map match-all FROM-SERVERmatch access-group name FROM-SERVER!policy-map FROM-SERVERclass FROM-SERVERpolice 500000000 conform-action transmit exceed-action drop!interface GigabitEthernet9/26service-policy in FROM-SERVER
I have a 3845 Router with three connected interfaces, one to my WAN, one to my LAN and another to my wifi zone. I want to limit the amount of WAN bandwidth the WIFI zone can take to say a max of one third and not restrict WAN bandwidth from the LAN at all.
View 7 Replies View RelatedI have cisco 7600 core router in ISP , i want to put the bandwidth limit on it for outgoing traffic (for internet) on a subnet because i am using Bluecoat and i want to test my bluecoat.On this subnet i have no limit for bluecoat but after the bluecoat i want to limit it. On 7600 cisco router i have not rate limit command so how it can be possible for a perticular subnet ?
View 1 Replies View RelatedI have two vlan interfaces, how to limit bandwidth on them ?I need than speed on each will be direrent.
View 1 Replies View RelatedVLAN ===> FE 0/1 {With subinterfaces - ALL INSIDE LAN INTERFACES} ==> ROUTER ===> BVI 0/1 {WAN Interface - OUTSIDE}
i am doing NAT for my clients in LAN to WAN - Static NAT i want one of my client who is excessing some service with his Public IP to get a specific amount of bandwidth ... as right now he is hogging all the bandwidth .i have 1841 router.
I want to switch to a slower ISP because of financial constraints (specifically downgrade from cable to DSL), so I'd like to set up my Windows XP computer so that it downloads and uploads at the same speed that the slower ISP does. That way I can kind of "try before I buy" for a week or so, to get an idea if I can live with the slower speed before disconnecting from cable and incurring a disconnect charge. I was told that some software that limits your bandwidth also may cause distortion in video or audio streams, so I'd like to avoid that.
View 2 Replies View RelatedMy router is a GT704-WG running on the default firmware. I need to limit a certain computer's bandwidth. Am I able to set the maximum download/upload speed for a certain computer via the router control panel (192.168.1.1)?
View 11 Replies View RelatedOn my home network I have 11 devices connected.Is there a way I can give each device a certain bandwidth limit so my Internet doesn't keep getting sucked up?
View 5 Replies View Relatedi have a internet cafe. i need to limit the bandwidth of our 30 computers for our customers satisfaction.
View 7 Replies View RelatedNeed to limit the amount of bandwidth a specific VLAN can use on a 802.1q trunk port. Situation is that we have a pair of Catalyst 4506 switches which have 802.1q trunk ports into a Checkpoint Firewall, this in turn is connected to a managed WAN router (to which I can't apply a QoS policy).If the 4506 was routing the traffic it would be easy to setup a class-map to match the IP traffic and then QoS the traffic, but the VLAN in question is trunked directly into the firewall (no L3/IP presence on the 4506 next hop for all clients on this VLAN is the firewall).What I need to do is restrict any traffic from this specific VLAN to 10Mbps on the uplink to the Checkpoint Firewall so it cannot impact the onward WAN.
View 1 Replies View RelatedI would like to be able to allow a specific client to only associate at 6mbit/s -is this possible using the wlc controller 5508? Another option would be to limit a whole w lan ssid to 6mbit/s but i can't find a way to do that either.
Other w lan ssid's on the same access points/controller need full data rates, so i guess i can't use the RF-profiling for this.
The Nordic World Ski Championships 2011 is upon us, and NRK, the national broadcaster of Norway, is offering HD streaming via the Akamai network.I run a network with 5000 users. Our internet bandwidth is usually 300mbps, but we've increased it to 500mbps for the duration of the Ski Championship. that did not work, because of the HD streaming.The internet link is delivered on a fiber trunk with many other VLANs, and my first piece of equipment in the chain is a Cisco 3560G (C3560-IPBASEK9-M), Version 12.2(46)SE). A port on the 3560G is then set to switchport access vlan "internet-vlan", and that port is connected to a routed port on my Cisco 6509-Sup720-10G ( (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXH3a). The 6500 then routes the traffic to a Cisco ASA 5520 (running 8.2(4)).What I'd like to do, is to limit the total bandwidth of all conversations between our IPs and the nearest Akamai IP-range, which is 195.18.221.128/25.How can I achieve that? I've tried to read the QoS chapter from the manual of the 3560G 12.2(46), but QoS is very complex stuff?
View 8 Replies View RelatedWe have a Cisco 3845 router and on the G0/0 interface we have our public switch with multiple public IP addresses (servers, routers, etc..) and on the S0/0 interface we have a DS3 Internet connection. I need to limit the bandwidth from the Internet (download) to one of the IP addresses on the G0/0 interface. I'm thinking of limiting to 256K and really need info with either a policy map or something equivalent.
View 6 Replies View RelatedI am using ASA Version 8.2(1) , I want to limit the vpn users to use less bandwidth of my Interlink to access something on inside network
example : source vpn pool
Destn : inside network
how can achive this with QOS config.
we have a bandwidth pipe terminating on 1841 BVI interface... now we want to limit all the traffic going from inside to WAN circuit to half... for example 10 Mb pipe we want to reduce to 5 mb on bvi interface.. how this can be done .. as of not there is not need to police any specific type of traffic .. this needs to be done for any traffic from inside to outside...
View 1 Replies View Related My company has a peer to peer network of 10 personal computers without a server. Operating systems from Windows XP to Vista. I've recently installed a Cisco RV120W Wireless-N VPN Firewall. It's configured in DHCP Server Mode with printers/copiers that have static IPs below the DHCP range.
I'm having a problem with certain stations being used for personal networking, shopping, etc. during business hours. Consequently I would like to limit internet access on these stations. However, some internet access is required because of online database software that's an integral part of our business. I've been reading in the Administration Guide about URL Blocking. Would it be possible to give static IPs to certain stations and then limit their internet access to 1 or 2 specific websites?
FYI, I've read about the Trusted Domains and Blocked Keywords but cannot quite understand how to parley this into the solution I need.
I currently have a 20mb connection with sky. I have 4 computers in my household and using the wireless modem router to distribute the connection.can I limit each computer to a certain amount of bandwidth. (eg PC1 =5mb, PC2=5mb, PC3=5mb, PC4=5mb) Two of my computers are running Win Vista HP and two computers are running Win 7 Pro & Ultimate.
View 1 Replies View RelatedI have a roommate who takes up a lot of bandwidth from the internet. I am allowing him to use my router which is a Linksys E2500. Is there anyway to limit how much bandwidth he can actually use.
View 1 Replies View Related