I would like to know if it is possible in dir655 ver 1.30 to limit bandwith in QoS using mac address?because in QoS Engine Name i can only see this opt. no opt for MAC, what if the user use DHCP?
View 1 Repliestell me the reasons that could cause the decreasing of the bandwidth in the TP cables? just 3 or 4 (main) reasons.
View 4 Replies View RelatedThey have an ASA-5510 with version 8.2(5). They just upgraded their Internet bandwidth to 30 Mb both ways.If we do a speed test in front of the ASA, we get 28 Mb/s upload and download, with a ping of about 5 to 10 ms.If we go behind the ASA, the download is about the same, the upload is decreased to about 12 Mb/s and the ping goes to 260 ms The license is base, there are no additionnal function added to the firewall (no IPS). I've check the speed and duplex and everything is fine.There are no drops on the interfaces or rules of the firewall, no drops on the Interface of the ISP router either. All interfaces are configured at 100Mb full duplex.I saw a couple of discussions on this in the forums, but they don't seem to come up with anything and they look like they end in the middle of the whole story, like once the problem is solved, they don't update their discussion.
View 6 Replies View Relatedhow to decrease high ping
View 1 Replies View RelatedAbout a week ago i started experiencing very slow download speeds... things like streaming online videos and having to wait which i have not had to do for the last 4 years. I did a speed test on multiple sites and my download speed comes out at about .2mbps and my upload is still where it should be at .6-.8mbps. I have a 12mbps connection so this does not make sense at all. Originally thinking it was malware, I formatted both my hard drives and did a clean install of windows 7 and it did nothing to resolve the issue. Could it be that my wireless card's radio is failing?
View 8 Replies View RelatedQuestion on two ethernet cables
But I am wondering will my overall connection speed decrease if I have multiple devices on? I am just curious as to if I have both say an xbox 360 and my computer on.
I am triing to migrate my old ACS to the new one. I am using ACS 5.3 on appliance CSACS-1121. Sometime, i loose the connection to the appliance and i could not connect to the appliance with SSH, i could not start the GUI and the authentication is switched to the secondary instance. As soon as I have traffic, the connection is restored.
View 3 Replies View RelatedI have a such setup:Code:
View 3 Replies View RelatedI've had the E3000 installed for several years and a few days ago saw my download speed drop by 80%. Trouble shooting with the Cable provider ended up with connecting directly from the PC to the modem and the speed issue was corrected. I don't see any recent changes in firmware, no new programs.
View 2 Replies View RelatedWe have a WDS connection between two AP541 access points, where one AP is connected to a SA540 with cable. The AP in the other end of the WDS does just act as a repeater, broadcasting using the same SSID and channel with WPA-PSK, as the cabled AP. For the WDS channel, we have tried WPA/WEP/none encryption without any difference. Spanning tree is enabled. 802.11 mode is 'bgn'.
Sitting physically beside the remote AP (the "other" and uncabled end of WDS) with a laptop using Intel 802.11bg adapter, we get a speed in the range 5-7Mbit/sec connecting to the cabled AP (3 of 5 bars signal strength in the traybar icon on Win7). But switching to the remote AP, which is beeing feed by the WDS from the same cabled AP previously being connected to, we do just get a measured bandwidth of 1-2Mbit/sec. I understand that some throughput is lost using WDS, but this does still look like a big decrease?Any experience using WDS with AP541, who can comment on if this is expected or not, and eventually any thing we can do to increase the speed?
I've been having this problem for quite some time, mostly since my mother bought her first Asus Laptop that came with an Asus WL-530g V2 wireless router.Problem is sometimes I get a random disconnect where Local Area Connection is identifying. On some occasions it reconnects on it's own after a few seconds, other times I have to diagnose the problem and I get a "Windows doesn't have a valid IP config" problem but it fixes that.The other problem, and I don't know if the two are related is that very often, for short/long periods of time I get a drastic reduction of internet speed. From what I can tell, it's got to be something to do with the network configuration or the actual router itself, it's very old and Asus stopped making firmware for it in '09. Useful data Basically I have a wired connection from my desktop to the wireless router.
>>>Asus WL-530g V2 Wireless router
>>>Atheros ar8151 pci-e gigabit ethernet controller (driver up to date)
>>>ISP RCS RDS
>>>DSL connection
>>>ESET nod32 Antivirus
[code]....
I have several computers connected to the network, can I restrict the download bandwidth on specific computer?
View 3 Replies View RelatedHow do I setup one IP to throttle bandwidth?
View 1 Replies View RelatedI just purchased a Dlink DSL-2750U today which I am using with my ADSL connection. I have three wired computers using this connection and no wireless systems at the moment. I would like to know if it's possible to share the bandwidth evenly amongst these three computers? The other two computers are hogging on the bandwidth leaving me with barely anything to work with.
View 6 Replies View RelatedHow can I limit the bandwidth of a router (DIR 600).
View 1 Replies View RelatedHow to calculate aggregate bandwidth of MPLS link. Is there any tool available for the same.
View 3 Replies View RelatedBought a DIR-601 for my sister and her kids for their home. Setup and works successfully. Sis asked if there is a way to give her laptop bandwith priority over the kids devices. As is, they are all sharing limited DSL bandwidth. Reading the manual, I see the QOS feature for specific types of traffic, and other limiters and schedules to shut out certain MAC addresses entirely. But wondering if this throttling feature exists in the router also.
View 11 Replies View RelatedI'm wondering if there is a way to prioritize traffic on the router's main WiFi over the guest zone or if there is a way to limit the bandwidth on the guest zone.
Ideally, I'd like to keep a locked primary WiFi for high-speed usage (I know, nothing it really ever secure) and an open guest zone for low-speed usage to whomever wants it. As far as I can tell, the DIR-655 doesn't support this kind of configuration.
i just increased my band width from my provider to 50 down ..3 up ..I can get almost the 3 up while connected to my d link but only about 2.5 down ..when i bypass my d link i get mid 40's down and 2.8 up .. for some reason my d link is slowing down my speed . I have a DIR825 hardwear B1 Ferm wear 2.07 NA
View 5 Replies View RelatedI just purchased a 100M fiber line to go with a brand new D-Link DIR-655 router. Before plugging in the router, I tested on my laptop directly from the modem and had great result speeds of 98M/97M. I connected the router, then plugged my laptop to find I was only getting speeds of about 10M/6M. This was true for both wired and wireless connections.
I took a look at the router settings. I turned off QoS, but that didn't work. One thing I did see was the WAN was set to auto. I attempted to change that to 100mbps or to 1000mpbs. However, when I did that my modem light that shows a 100M connection is active turned off and I couldn't get internet. I was only able to get a connection if I left that on auto. Is there a setting somewhere that is limiting my bandwidth from the router?I reset the router twice and checked to find I had the latest firmware. Is there something that I am missing? I have always been a Linksys fan, but wanted to see how D-Link is.
This has finally become a BIG problem. Any time I have iTunes running and downloading podcasts, it hogs all the bandwidth for the Internet (but not the local network). This is not only slowing down access from the machine running iTunes and the downloads but for every other device trying to web browse.I'm running two Macs and one Windows/Dell PC on the network. All are hard-wired (Ethernet) to the DIR-655. How to throttle iTunes? I did some research and found that I am apparently not the only one having this issue.I'm about to bail on iTunes entirely and try to get used to Miro, which does allow bandwidth control.
View 3 Replies View RelatedI have a D-Link DSL 2640B on the way which I plan on using to replace my 2Wire modem. The 2640B is a combination of a modem/wireless device. Does it dynamically load balances the internet connection? Sometimes while I'm playing online games on my PC and a few others are using the internet for browsing or Youtube, I lag A LOT. Latency shoots up from 10 to 200. QoS goes to ****. And I only need 0.50-1Mbps to keep a steady online play. This was the problem with my 2Wire. So does the 2640B load balance the bandwidth?our max speed is 3.5Mbps according to the ATT Rep.
View 10 Replies View RelatedWe have a DSL line at work which a few people share for Internet access.Sometimes if someone is doing a Windows Update or big download etc, the connection is maxed out and slow for everyone else.Is there a way to give everyone a set amount of bandwidth via a Cisco router (2811) or will I need to use something like a packeteer?
View 4 Replies View RelatedRegion : UnitedArabEmirates
Model : TL-WR941ND
Hardware Version : Not Clear
Firmware Version : 3.13.9 Build 120201 Rel.54965n
ISP : etisalat.ae
How to controller wireless bandwidth in WE941ND.
I have playon and the online bandwidth is showing slow. I did speedtest and it shows 20mbps, but the playon says below 2. No windows (7) security is enabled and avast is turned off. i rebooted and get the same results.I also cannot do any updates for my windows 7. I try and it says that it cannot do the update. I check the logs and all of the updates were done fine up to when I installed the 655; now it doesn't work.
Playon support says check network, which I have done, and the only thing left is the 655.
I have three laptops (running ubuntu with different kernel versions) with wireless adapter Intel Corporation PRO/Wireless 3945 ABG. Laptop A ----- Laptop B ----- Laptop CI created an adhoc connection in laptop A with: Essid: 'ad_hoc', IP address: 10.42.43.1, Subnet: 255.255.255.0, Gateway: 0.0.0.0, Now the laptops B and C can see the wireless connection 'ad_hoc' and I can connect to them after setting IP 10.42.43.1 and 10.42.43.2 respectively. So, I created the adhoc connection between 3 laptops. Now, I wanted to check the bandwidth between the different paths. The tool iperf was what I used for TCP bandwidth calculation. The bandwidth between A and B was around 4.5 Mbps , between A and C was around 4.0 Mbps but the bandwidth between B and C (B being server) was 677 kbps whereas C being server was 3.99. I don't understand how can the bandwidth drop so high when B was made the server. The system adapters are identical.
View 1 Replies View RelatedI want to use MRTG to monitor my DSL connection bandwidth useage.
Should I monitor:
ATM 0/3/0 or
Dialer 1 or
Virtual-Access 2
ps. is the 'BW' aspect of show interfaces important? I have 56Kbit/sec on Dialer 1, 100,000 Kbit/sec on Dialer 1 and 1024Kbit/sec on ATM.
Region : Spain
Model : TD-W8968
Hardware Version : V1
Firmware Version :
I have a TD-W8970. In settings "Bandwidth Manager" there is an option to put a value between 1 and 8, but does not specify which is better (1 or 8). What the value to give more priority to a computer to another?
I need an tool to monitor the internet connection and bandwidth at my windows xp desktop.
View 4 Replies View RelatedMy younger brother uses IDM to download files and it slows my Internet down to a crawl. I've tried reasoning with him but its not getting through to him. Is there any way I can use my router (bcz only I have access to it) to limit IDM?
View 5 Replies View RelatedRegion : India
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
ISP : MTNL
After lot of troubleshooting and efforts I figured out there seems to be BUG with routers firmware 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n.When you enable Bandwidth control, FTP stops working from Internet. However, it does work from local network. When you disable Bandwidth control, FTP starts working from internet as well as local network.
Region : Romania
Model : TL-WR841ND
Hardware Version :
Firmware Version : 3.13.27 Build 121101 Rel.38183n
ISP : cosmote
hardware version is WR841N v8.wireless works just fine. i use it for my smartphone and an old laptop. i use ethernet cable to connect to main computer where all is ok until i start using my bit torrent client. as soon as i build up traffic above 1MB the ethernet portion of the router freezes and needs a reboot. when frozen, wireless is still working and i still have access on the lan to the router via my browser. i got this router so i could have wifi for my phone. my old router (asus rx3041) worked just fine and i accessed my isp at the maximum speeds it would allow on a 60 gigabit connection.
Region : Canada
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.17 Build 120426 Rel.29216n
ISP : Bell Canada
Just had my line upgraded to 50mbit down, and 10mbit up. Whenever the router is between the PC and the modem, my speeds drop to 30mbit. If i plug directly into the modem, I get the full 50Mbit. Upload speeds are always 10mbit.I've tried power cycling devices, and even replaced all cables with cat6 (which I know isn't the issue, but i'm just trying to eliminate everything)