I have 4 autonomous AP 1142 with 2 ssids : SSID10,vlan10 & SSID20,vlan 20.I use ACS 4.2 in order to authenticate users (EAP-FAST). How can i restrict access base on ssid or on vlan?I want users that connect to SSID 10 to not have access to SSID 20 and the opposite.
View 7 RepliesI would like to ask some question on WLAN technology, which I using WiSM version 2. And i get requirement that user must be restrict with SSID, so, i found that it can do it on ACS version 4.x via NAR for SSID-based authentication feature. Then, is it possible to do restriction on ACS Version 5.x?
View 4 Replies View RelatedOne of my Clients just aquired a CISCO ASA firewall, and they would like to restrict internet access, that is they want to block internet for Junior employees while managemnet remains connected, Looking at the situation, The ASA serves as the gateway,I tried an Access list like below for one pc to test if it works but instead everyone just went off, may be i misfired somehwere.
Access-list 110 deny tcp any host 192.168.20.100 eq wwwAccess-list 110 deny tcp any host 192.168.20.100 eq 443Access-list 110 permit tcp any any eq wwwAccess-list 110 permit tcp any any eq 443access-group 110 in interface inside
I'm running a wpa2-secured guest ssid on a particular vlan that allows traffic to the web but restricts any access to internal network resources. It had been working fine for a couple of weeks, until the network started intermittenly dropping - at first I tried swapping channels and rebooting, but there has been no progress. I keep a running log at all times as long as the network is still active, but once it drops, the only message I'm getting is
'Line protocol on Interface Dot11Radio0, changed state to down'
My understanding would be that this is the same message logged when a user manually turns off the radio from a terminal window, is this correct? Or am I missing some basic troubleshooting steps?
The GUI times out after 60 seconds.
Since the the "exec-timeout" setting has a default of 10 minutes (if I'm not mistaken), I don't think I could change the timeout value with that command.
Under the "Association" tab of the GUI, there is an "Activity Timeout" subtab and settings for 5 device classes, all set at 60 seconds.
I would guess the setting in question can be configured here. Is the client station device class what I'm after?
I wonder if there is a way to rename an existing SSID on aironet 1142 without destroying/recreating. I tried downloading configuration/ changing name/ re-uploading however that didn't have desired effect. There doesn't seem to be a way via web-GUI.
View 3 Replies View RelatedI configured the device manually, not even using Express Setup or Express Security setup so... it is possible I missed something.Anyway, here's the problem. Although the SSID is configured as "AP1", this SSID does not appear among available networks on the client laptop.
The connection, configured in Group Policy for the client, should actually happen automatically, based on the SSID, but since the SSID is not being broadcast, that connection is failing as well.
The Aironet does appear among the available networks as "Other Network" and if I click on "connect" I am prompted to enter the SSID -> AP1
Although, unexplicably, an error message displays (Windows cannot connect to the network, or something to that effect), the laptop *does* connect once I close that window. Network access is complete and functional - I can ping other hosts, etc..
I'd post screenshots but not knowing what setting is missing or incorrect, I'd have to print dozens. So here's the sh run output of the AP obtained via telnet (just below). This is a test network so all information is "real" (nothing changed for privacy):
Note: I even changed the hostname to "AP1" (it's still LAB1 below) but that did not resolve the problem (did not think it would).
LAB1#sh runBuilding configuration...
Current configuration : 2321 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname LAB1!logging rate-limit console 9enable secret 5 $1$9EWD$kxrbg8KxikRFypOieKiZh/!aaa new-model!!
[Code]....
I am deploying ISE with WLC 7.4. I have two SSID(s) running in my network 1. Corporate & 2. Services. I have a domain setup lets say "AD.com" with 4 groups 1. Corporate, 2. Services, 3. Employees, 4. Contractors.Here is an example of the scenario that I want:
AD.com Group : Corporate's User : 1. C_USER1
2. C_USER2
3. C_USER3
4. C_USER4
5. C_USER5
[code]....
Now what I want to do is have 802.1x authentication on my Corporate SSID that will check in AD.com, ONLY AND in ONLY corporate group for authentication. That is only C_USER1 to C_USER5 are allowed to connect to it. Users from any other AD group shouldnt be authenticated on this SSID.The same for the services group & SSID.
I am using Cisco 7609 IOS15.0(1)S1 and Cisco 3600 IOS 15.1(2)EY.I am trying to provision VPNs over MPLS network.All I found in the documentation is how I attach a whole interface to a VRF.However, I need to be able to attach a VLAN (or any other matching criteria, for that matter) to a VRF.In other words, I want to be able to attach port 1/1 vlan 100 to VRF-A and port 1/1 vlan 200 to VRF-B.
View 1 Replies View RelatedI'm trying to configure ACS 5.2 to assign the VLAN to a user dynamically based on the AD group that the user belongs to. I've gone into:
Users and Identity Stores -> External Identity Stores -> Active Directory -> Directory Groups tab
and selected the group name from the AD. If I understand correctly, I should now see this group under:
Policy Elements -> Authorization and Permissions -> Network Access -> Authorization Profiles -> Common Tasks -> VLAN ID/Name
However, it does not. Am I missing something?
The issue that I have is around getting second SSID work on my router! So I have created two Vlans, 30 & 200. Vlan 200 is the native and is associated to SSID "Bitter". This SSID works like a charm however the other Vlan cannot be even pinged from router side the ip that I tried to ping is 192.168.30.1. I have posted the config below. Also i tried to brak wlan-gig into sub interfaces but the IOS does not accept that!
Vlan 30 >>>RadioDot 11 0.30>>>>Gigabit 0.2>>>>bridge group 2
Vlan 200>>RadioDot 11 0.200>>>Gigabit 0.1>>>>bridge group 1 (native Vlan)
Router side:
ip source-route
!
!
!
ip dhcp excluded-address 10.10.10.1
[Code]...
I was unable to configure vlan-based qos on Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9-M), Version 12.2(33)SXH6, RELEASE SOFTWARE (fc1) Seems to me my configuration is not working. Here is the output of the interface:
sh int G1/6 | i rate
Queueing strategy: fifo
30 second input rate 25231000 bits/sec, 4282 packets/sec
30 second output rate 46940000 bits/sec, 9257 packets/sec
And here is my configuration:
interface Vlan3
ip address 192.168.1.1 255.255.252.0
service-policy input TEST_IN_PMAP
service-policy output TEST_OUT_PMAP
[code]....
Why I can't see matches in ACLs? I've double checked the direction and seems to me it is correct. I can't see matches even I configure something like this:
10 permit ip host 192.168.1.168 any
20 permit ip any host 192.168.1.168
Why my output rate is higher than 30M? Is it bacause there is no matching traffic here in ACLs? I'm absolutely shure that this host with such ip connected to this interface:
#sh arp | i 192.168.1.168
Internet 192.168.1.168 0 feed.beef.f00d ARPA Vlan3
#sh mac address-table | i feed.beef.f00d
* 3 feed.beef.f00d dynamic Yes 0 Gi1/6
is it possible to multicast between 2 different SSID's that are associated to 2 different VLAN's?
View 2 Replies View RelatedI'm using access point AIR-AP1141N-E-K9 and want to use Multi SSID. Based on Cisco document, when I config Multi SSID in access point, each SSID have a separate VLAN, is it a must have ? Can I use multi SSID without VLAN ?
View 5 Replies View RelatedI have a WRVS4400N that broadcasts two different SSIDs. One is a public network and the second is a private network. Right now, both SSIDs are pulling from the same DHCP server, but I would like to separate the public from the private. How can I separate these SSIDs by vlans? I can't seem to get the vlans to route to separate ports.
This is my vlan settings. I have two DHCP servers right now. One is in an isolated network plugged into Port 3 of the WRVS4400N. The other is on the production network, plugged into port 1 of the WRVS4400N. For some reason, whenever I connect to SSID Public, it won't pull an IP from the DHCP on port 1, it only pulls it from the one on port 2.
I know there is three SSIDs here, the Static one is going to be the same network as the EMS one.
I have around 60 , 1142 N APs . As of now i have only management VLAN ( for IP ) & one user vlan 350 configured on the access point . All the users connect to VLAN 350 and they get IP as required.However in our new set up there are couple of requirements have come up were in SSID will be the same however we have created many VLANs for different kind of user group and all these VLANs should be mapped to this single SSID and pick the IPs from their respective VLANs .
We have done configuration on the RADIUS server side were in we have mapped the users in their respective VLANs and they are getting authenticated via AD . Now how do i map my these 4-5 VLANs in a single SSID in Access Point.
I have one cisco wlc 2112 with ios 7.0.230.0 with license to support 12 access points. My access points are nine (9) lap1231ag and one (1) lap1310.I just have one wlan (ssid). My scenario of deployment is in layer 3. I have one interface management and ap manager in the WLC. All my Access Points have differents ip address that WLC. I need to configure a unique ssid to associate my six (6) dynamics interfaces (each dymanic interface with different vlan subnet).Each wlan profile (ssid) should have the same security in phase 2 (wpa2/psk). My cisco access points don't support hreap. My wlc support only (4) interface into an interface group, and i need six (6) dynamics interfaces.
View 6 Replies View Relatedhow to change our wireless setup. Currently, we have 2 Cisco AiroNet 1130 WAP's in the office that go directly into the 2 POE ports on our Cisco ASA 5500. These WAP's have 1 SSID and are using WEP for security. After demonstrating the flaws of WEP to my boss, he has agreed that we should use something more secure and I've suggested WPA. We want visitors to our office to be able to hop on our wireless but on a separate guest SSID with WEP.
I'd like the internal SSID to route to the ASA and take the default route to the internet (it will be our new fiber connection once it's installed in a couple weeks). The default route is whichever connection is working since our ASA 5500 will fail over when it detects an outage.
I'd like the guest SSID to route to the ASA and then go over our existing cable connection. This connection will be our backup once the fiber connection is installed. Since we won't be using it very often, but will be paying for it, I advised that we send all guest wireless traffic over this connection since 50/5 is plenty for guests.
The current SSID (which will be the internal SSID) has no VLAN. We do currently have a few VLANS on our network, one for voice (.42) and one for data (.100) and the default (.0). What device to I create the VLAN on (Cisco 5500?) and how to I setup the WAP? I need very basic instructions to start and I'm also trying to do this without causing downtime if possible.
I've attached a diagram of what it should look like. Red indicates our internal network and Blue indicates the guest network. I can send screenshots as well.
I created a second VLAN and a second SSID. My problem is that from a PC on the native VLAN 1 I can ping the IP of VLAN 2 192.168.2.254 but I cannot ping any other device that has connected to the second SSID. How do I get routing to work between the two VLAN? I thought it would be automatically setup when I created the second VLAN using Cisco Configuration Professional?
View 3 Replies View Relatedi`m facing a problem configuring the mentioned access point to act as stand alone access point with multiple SSID assigned to differnet VLANs the problem is that
1) i`m not able to broadcast the both SSIDs in the same time from the Access point
2) i need to make the radius server to manage the SSID access for the wireless clients (trying to find a way in which the aceess point sends a log for the radius server containing the VLAN id /IP address of the the SSID) you may find the below info about the IOS ver. & the configuration?
i`m running IOS /c1100-k9w7-mx.123-8.JEE/c1100-k9w7-mx.123-8.JEE?
How do I...add a dos based computer to a network running windows 2003
View 1 Replies View RelatedThere are 10, 50 and unlimited users profiles for the ASA 5505, reason for that restriction? Does that mean for example that only 10 users can go through a 10-user 5505?
View 6 Replies View RelatedWe are using ASA 5510 Version 7.2(4) at our organisation. The requirement is we need to give an access to a user with limited access so that he can run only specific commands on configuration mode. We don't have Cisco TACACS server instead of that we are using a microsoft radius server.
View 6 Replies View RelatedI am running the SGE2000 as my l3 core switch with multiple inter-vlans.
have a customer requirement that needs to restrict eg. GUEST-VLAN10 to all other VLANS in the network. Only allowing access to the internet.
It seems on the switch i am able to bind ACL to per port interface. if this is possible on the SGE2000
Router 2811 got 3 Interfaces. One Interface connected to INTERNETProvider, Second Interface connected to Sales_Dept, Third Interface connected to Business_Dept. Internet Bandwidth in Total is 8MB. I need assistance to allocate 6MB total bandwidth to Sales_Dept and 2MB total to Business_Dept Sales_dept has 48port switch 2960, Business_Dept 24 port switch 2960. Gateway for users is the 2811 Router and both are on different subnets
View 3 Replies View RelatedI am using a network switch to share my broadband between four PCs.Among these PCs, one is for students. Is it possible that I can do the following 2 things from modem whose page can be accessed through 192.168.1.1;
1. Restrict some website like Facebook, Youtube etc
2. Limit download speed of that PC to 100KB/s
I am a restaurant owner and have a wireless network set-up via DLink DSL 2730U router. Now some times I get customers who demand to use the network and they use it for free which I find irritating. I have found one solution of 'Guests/Virtual Point' but I need to limit the time (say 15 minutes) for which they can use the network.
View 1 Replies View RelatedI've my ACS linked with AD to give administration access to few network devices and I've created an access policy to link my AD groups with those network devices and command sets.
Unfortunately I found I can use any user from my AD to login to my devices. Only LOGIN, the authorization definition is restricting the command set for those users.
How can I restrict the LOGIN to an specific AD group?
I get that to avoid fragmenting the packets we need to reduce the MTU to 1492, fine, but should the MTU restriction be applied at the virtual-template (server)/dialer (client) or on the physical ethernet interfaces?If I apply it to one or the other, which takes precedence? Should I just apply it to both the virtual/dialer interfaces and the ethernet interfaces?
View 6 Replies View RelatedI am trying to create a user restriction to allow one user to access only two networks (10.192.3.0 and 10.192.5.0) I have range of networks but I want to permit only two networks for limited user and full access for the admins. I know this was possible with ACS 3.3 but I am not too sure if this is also applicable with ACS 5.2.
View 1 Replies View Relatedi have asa 5520 configured as VPN Gateway to terminate remote access vpn , i have question , how can i restrict the access to only 1 range of public source IPs to access my corporate via RA ,is this possible?if so how to configure it?
View 1 Replies View Relatedmy client insisting to set a dscp value of 56 (= CS7 , the highest priority) for their video packet without any bandwith restriction in the input of fast ethernet port and PPP Multilink serial output port of the 7513 router. What will be the outcome at time of video streaming and video conference ? As this dscp value CS7 is the highest priority and reserved for network only.we are using ospf routing (some of the network is connected through this multilink port via ospf routing), also this ethernet is connected to various statice routed ip network via cisco asa and cisco 4507. The keep alive ospf neighbor router will be lost or not?
View 2 Replies View Relatedwhen im entering ip address of other computer in my remote desktop an error msg is coming "unable to logon you because of account restriction" fire wall and virus protection is off.
View 1 Replies View Related