I have a switched network of C2980 & C3548 switches with multiple VLANs. I would like to understand the difference between Multi- VLAN ports and trunk ports. What circumstances would dictate using one over the other? If I configure the router port as Multi- VLAN, does the router still require sub-interfaces?
View 9 Replies
I have trunk etherchannel ports 47,48 which both have Vlans allowed on trunk 70,71. Everything works pretty fine. Now I am trying to add a new VLAN 72 to these ports.
conf t
interface FastEthernet0/47
switchport trunk allowed vlan add 72
exit
exit
So far so good. But when making the same command for port FastEthernet0/48 my switch stuck.
I have just configured up a sg500 with a lacp trunk to an upstream switch.
I am getting native vlan mismatch on the individual ports of the lacp team.
24-Jan-2013 12:54:48 %CDP-W-NATIVE_VLAN_MISMATCH: Native VLAN mismatch detected on interface gi1/1/24.
24-Jan-2013 12:57:35 %CDP-W-NATIVE_VLAN_MISMATCH: Native VLAN mismatch detected on interface gi1/1/48.
[Code].....
How does the ESW 500 or SF300 line guarantee QoS of voice traffic when trunking switch to switch? I have (2) ESW 500 series switches in series. The phone on switch 1 have no audio issues, but the phones on switch 2 (the last in the series) have intermittent voice quality issues when dialing across a WAN circuit to another office. The phone on switch 1 do not have that issue though they traverse the same circuit. They are all using the same VLAN 100.
View 1 Replies View RelatedScenario: I have a vmserver w four virtual servers all in configured w in different subnets. What's the best way to configure a 3750-x switch to route traffic from the virtual servers to their vlans?
View 2 Replies View RelatedI'm using access point AIR-AP1141N-E-K9 and want to use Multi SSID. Based on Cisco document, when I config Multi SSID in access point, each SSID have a separate VLAN, is it a must have ? Can I use multi SSID without VLAN ?
View 5 Replies View RelatedI am using an SRP541W router and i am trying to configure 2 vlans, each one to use its own Wan:Here are the dhcprules and vlans:As can be seen, each one has its own wan interface.
Vlans:As can be seen, each vlan is using its own ports and dhcp rule, so, now they should be separate.
Both Wans are connected: So now (at least as i see things) the two vlans are separate and using different Wan. But the reality is different, everything is going out using Wan1.Also in the Interface Info you can see that the 2 vlans are listed under the Wan1.
The rest of router setting are default.
why i can not found ip router setting by main menu? the sg300-28 can not support ip router command?mor informations,see my img. If sg300-28 can not support ip router command,what i can do it that communicate by multi-Vlan ?
View 2 Replies View RelatedI'm new to Cisco equipment much more familiar w/ Sonicwall w/ that said......I have a 5505 w/ Security Plus licensing
I have set up multiple VLANs as follows
VLAN 1 inside - still setup as 192.168.1.1 (will not be using this for our lan)
VLAN2 - outside
VLAN100 - LAN 10.1.1.1/24
[Code]....
If I do add all the VLANs above I understand I will probably have to make a trunk port since I only have 5 usable interfaces
I have a test switch (Cisco 3550) that I want to set up with 6 Vlans and 2 trunk ports. I want to be able to access a virtual server conected to the trunk ports from the switch ports. Ports Fa0/1 to 8 are in a vlan port fa0/9 to 16 another vlan etc. Ports Fa0/47 and 48 are the trunk ports. This is a lab environment so the the switch is the only device being used.
View 4 Replies View RelatedI've previously used trunkports and vlans between my ASA and accesspoints, connected directly. Now I want to put a 2960S-24PS-L bewteen. Where should i define the vlans (in the switch or in th ASA?) and what ports to put in trunk mode? (the ones on the switch or the one between the switch and the ASA?)
View 1 Replies View Relatedi would like to setup a L2 VLAN trunk connection over a VPN. I hear this can be done with a GRE tunnel. I currently have Cisco MWR2941's that i would like to configure the TRUNKs on then push them over a 5520 VPN ( IPSEC Tunnel ) to a 5510. on the other side of the 5510 i will have another MWR2941 to recieve the trunk.
how to configure this trunk or some configuration ideas?
On ASA 5515 it shows it is in transparent mode and it has multi context.As in transparent ASA we know it has single Management IP address.This ASA is connected to one switch on two ports gi2 and gi3.One port carries vlan say 800 to the ASA.Other port carries vlan 500 from the ASA to switch But when i log onto ASA and do sh run it shows no VLan info there.
View 3 Replies View RelatedWe have around a dozen Catalyst 3560 and 2960 switches in a ring topology. We are considering adding storm control to our trunk ports. Up until now we have only used it on edge ports with default values and without error-disable.I am proposing that we also add storm control to trunk ports at a lower level and that we error-disable only the redundant links that make up our loops.
-storm-control broadcast level 25.00 20.00
-storm-control multicast level 2.00 1.00
-storm-control action shutdown [only on redundant links]
In a storm all links will restrict broadcast which should work accessing remote switches, but the redundant links should errdisable and block the redundant path. It is important that the action line is not applied to links that are not redundant as we could isolate parts of the network. Any reason not to use storm control on trunks?
I have been experiencing discards and no buffers errors on my 2950 switches. These switches are connected to two core switches 4948 and 3560G. I have noticed previous posts regrading these problems but have been unable to find any cases that were resolved. We are using 12.1(22)EA11 software on our 2950 switches.
Outputs:
flrnet3#SH controllers ethernet-controller gigabitEthernet 0/2
Transmit Receive 22204993 Bytes 904542488 Bytes
[Code]....
I'm trying to obtain the vlans on a trunk and also whether the port is a trunk. Ive seen VTP mib, but these dont appear present on my switch (2950).
View 4 Replies View RelatedI have a Cisco SG300 switch on which trunks are configured. I have a server which sits on the switch via a trunk link of four network cables (4 Gbps total)on which LACP is enabled. I'm having trouble connecting to the server using VNC from a computer on the network. It doesn't happen all the time though, it's just random.
On looking at the logs of the switch, I saw something unusual. The trunk that connects the switch to the server is constantly removing all the member ports and adding them back again after a few minutes interval. That causes the trunk link to flip on and off all the time. What could be the reason that's causing it to happen? I know it could be the network cable but I'm using brand new cables and the server also is brand new.
I have been though the setup a couple of time with no luck pinging one pc to another from vlan 10 to vlan 20. I posted the running configs and some other information from my router and switch. I am relatively new to all of this so if you need me to post more information from the hardware let me know and Ill put it up. There are no firewalls in place and I know the cables are good because I switched them around to make sure. Also when I change the ip on my second machine for vlan 10 I can ping from one pc to the other but when I try the same for vlan 20 I get nothing.
**From my 2950 switch**
Current configuration : 2825 bytes
!
version 12.1
no service pad
service timestamps debug uptime
service timestamps log uptime
[code]...
ASA 5505, I got a security plus license which allows multiple VLANs.I want to be able to configure the ASA to allow only RDP session (One way) to another Switch where all the VLANs are. I've attached a pic of what I want but I'm struggling.
I looked at documentation saying you should have inside and outside interface but I'm not sure on this scenario.I've configured inside interface on ASA e0/1 and interface VLANs but not sure what to do between ASA and Switch?
I have 2 hosts, 1 plugged in fa 0/21 in VLAN 101 and another in fa 0/22 in VLAN 101 on our L2 Cisco 2960. If I try and transfer files from either host the gig 0/1 trunk port on the 2960 leading tot he 3750 fa 0/1 port hits 100mb (using a real time bandwidth monitor tool), but why? This VLAN is on the same switch, why does it go one way up the trunk to the L3 3750 switch? The L3 3750 is the VTP server and the 2960 is a client. I would of thought the traffic stays local. The 2 hosts don't even have a gateway set.To sum up the typology the 2960 and 3750 are trunked using a single cable. The 3750 hangs of a ASA firewall using SVIs.Here is whatthe traffic looks like when copying a file between hosts (2gb file).
3750 L3 Switch (VTP Server)
interface FastEthernet1/0/4
description Trunk to Cisco 2960 Gig 0/1
switchport trunk encapsulation dot1q
switchport mode trunk
switchport nonegotiate
[code]....
I need to set QOS in our new network. We have connected 2 cities together with 700Mbit leased line. On each side we have Catalyst 2960S switches and between them is TRUNK for VLAN 10 and Vlan 20.Vlan 10 is for IPTV (fixed 400 Mb/s for CATV)Vlan 20 is for Internet (rest).Sometimes is happening that Vlan 20 takes more than 400 Mb/s for a few seconds and in this situation we have problems with CATV.Is there any way to make a guaranteed bandwidth 410 Mb/s for CAT - VLAN 10 on this swithces?
View 2 Replies View RelatedI have got 2 Cisco switches (3560G and a 3560X) connected by a trunk port. see config below:
3560G#sh run int gi0/26
Building configuration...
Current configuration : 130 bytes
[Code].....
I can't seem to get VLAN 79 through to the first switch (3560G). Beyond this switch there is a router with acts as default-gateway for the respective VLANs. For VLAN 79 it is 192.168.79.1. I can ping this from the first switch but can't ping it from the second (3560X) switch but can ping 192.168.25.1 which also is the default gateway for this switch.
We bough an Cisco 2911 router, and as i see the "ip sla monitor" command is not supported. Which license/IOS upgrade should i buy the fullfill this. And i cant add a trunkport to the iunterface even cant add a vlan to interface. How do i a trunkport on the cisco 2911 router. ANd how can i do a vlan on a interface on the router.
View 2 Replies View Relatedcan i have 4 links from an ESX server to 6500 , each link represents a trunk link carries each the same 2 VLAN , 100 and 101 , keep port-channel out of the picture , does it work well?
View 12 Replies View RelatedI have a 2960 switch connected to another. The I need to verify that vlan0010 on one switch is forwarding tagged traffic between the other switch it is hooked up to through the Gi0/1 port. How do I verify this? I have a server that's multihomed (Broadcom) on the other side an it is supposed to be on this vlan with one of it's network interfaces. We had a pwer outage and now it cannot communicate on this vlan. However, everything else on the vlan can reach all the other nodes accept this server in the front of my building. All the devices in the same room are linked to the same switch which has one port (fa0/17) on vlan0010 and can ping eachother just fine. The server is hooked to port 24 on my server room switch and Gigabit port one goes to a fiber converter all the way to the back. It then gets converted from fiber to cat5e again and links into the switch (2960) in the backroom.
View 5 Replies View RelatedNeed to limit the amount of bandwidth a specific VLAN can use on a 802.1q trunk port. Situation is that we have a pair of Catalyst 4506 switches which have 802.1q trunk ports into a Checkpoint Firewall, this in turn is connected to a managed WAN router (to which I can't apply a QoS policy).If the 4506 was routing the traffic it would be easy to setup a class-map to match the IP traffic and then QoS the traffic, but the VLAN in question is trunked directly into the firewall (no L3/IP presence on the 4506 next hop for all clients on this VLAN is the firewall).What I need to do is restrict any traffic from this specific VLAN to 10Mbps on the uplink to the Checkpoint Firewall so it cannot impact the onward WAN.
View 1 Replies View Relateda number of vlan on trunk is 4096, can I limit this number? I need trunk pass only 10 vlans.
View 1 Replies View RelatedCurrently we have a 6513 core (running IOS and doing limited routing) with VLAN Trunking to about a dozen 3560 edge switches, with various VLANs going to each of the edge switches. All works well. We are downsizing and replacing the 6513 core with a 3750G stack. We have the stack up and running in the lab, and want to slowly (as we move floors) migrate all of the edge switching to the 3750 stack.
The plan is to connect the 3750 stack to the 6513, then slowly migrate the edge switches to the stack (from the 6513). I would like to put in place 4 x 1GB trunk links between the 6513 and the 3750 stack before I start moving edge switches to ensure adequate bandwidth. Once all of the edge switches are on the new 3750 stack, I will start to decommission the 6513.
What is the best way to configure the links between the cores (old 6513 and new 3750 stack)? I can easily get the edge switches configured to the 3750, but am worried about the core links. I really want to avoid having to perform an all-at-once cutover of the cores. Another question is when do I try and migrate the VTP server role from the 6513 to the 3750 stack? I could simply make everything transparent, and ditch server-based VTP, as we rarely change or creat VLANs.
I have several closets with Cisco 3560 on the edge that I'd like to change the vlan that's used for the management vlan on each. In the core I have a Cisco 6509 with Sup720's.
I'd like to do this by changing the native vlan on the trunk port on the core 6509 interface that connects to the 3560. and leave the management vlan on the 3560 as vlan 1.
Seems trivial but what I tried didn't work and I didn't have the window to troubleshoot. I'll paste the simplified configs for the interfaces below
!
6509 configs:
!
interface Vlan50ip address 172.16.50.2 255.255.255.0!interface FastEthernet
[Code]....
I need adding a vlan to the trunks bundled in port channel. I know how to add v lans to a port channel with Cisco IOS but with CAT OS.
I have 2 ports bundled to form ether channel in switch which is running CAT OS. There are already few v lans allowed in the trunk of each interface. now I need to add one more v lan.
For Example:-
v lan 135 needs to be added in addition to the existing v lans.
clear trunk1/2 1-112,115,117-134,136-4094
set trunk 1/2 on dot1q 113-114,116,135
and similarly on the 2nd interface
so if I add vlan135 to the trunk one after another will it cause any service disruption?
I have a 3750 as a core and have a series of HP Procurve switches that are daisy chained using one port. I have two vlans on the port now (6 &9) and everything works fine, all switches communicate and end devices on the switches are also talking. There is a requirement to add a device towards the end of the chain which requires it to connect using Vlan1. Once I add Vlan1 to the port onthe 3750 I lose connectivity to all the HP switches.
View 4 Replies View RelatedCurrent Situation:We are able to reach server IP -10.203.206.40 from our 4948 switch vlan 10.30.1.0/24 through the Layer 3 interface between 4506 and 4948.
Requirements
==========
1) Now we would like to add one more L3 interface between 4506 & 4948 for redundancy purpose.
2) Make available Vlan 540 in 4948 from 4506... need to create two trunk links between 4506 & 4948 and allow vlan 540.
This is regarding VLAN creation on C3750E switch.I want to create new Vlan 94 on this switch and also I want to allowed same interfaces like Vlan 95 & Vlan 96. [code]
View 7 Replies View Related
