i have dlink dwl g700ap wireless access point.. router will show default and no password. i try to connect by ip 192.168.0.050 as per manual guide by cannot.my default gateway is 192.168.1.100 taking lan wire from builing internet that used cisco.
View 1 Replies
Here is my set up:
192.168.1.1 is a Linksys WRT610N acting as a router and DHCP server for addresses .100 to .150
192.168.1.2 is TEW-639 with DHCP turned off and connected to the Lynksys via one of the LAN ports.
I then have a FosCam camera with IP 192.168.1.010, connected either wirelessly or via a wire on a LAN port to the TEW-639W.
Here is my problem: If the FosCam is connected wirelessly to the TEW-639W I am unable to see it from any device connected to the Linksys. If I connect the FosCam via a wire to a LAN port on the TEW-639W then I can see it from a device connected to the Linksys device.If a device is connected to the network via the TEW-639, I can see the FosCam whether it is hardwired or wirelessly connected to the TEW-639. What am I doing wrong?Why can I not see the wireless connections on the TEW-639 from a Linksys connected device?,The setup is that the internet comes in and is connected to the Linksys, which then via LAN cable and LAN ports on both devices is connected to the TEW-639, which is then connected to the camera.
I have high-speed cable access currently coming into an older D-Link 4-port wired router. I need to buy a new wired and wireless router so I can sync my new Android 4G phone (I'm in an area with bad cell coverage but I can sync with wi-fi). I have a second house about 200 feet from mine and have 3 Cat5E lines running underground in conduit to it so the lady next door and and her two kids can use the internet (I have 40-50mb service for my business use at home). Problem is that my kids have discovered YouTube, streaming video, video chat, etc. and are burning up my bandwidth. I currently have two of the lines to them disconnected so that I can limit their use to one computer at a time. I'm considering having them buy a Wireless Access Point, can they connect it to the standard single Cat5E LAN wire that is coming from my new wired and wireless router when I buy it?
View 2 Replies View RelatedI just switched over from AT&T Uverse to time Warner cable for Internet. I bought a Motorola Surfboard sbg6580. I have the surfboard hooked up and all is well. Now I would like to do in put the old 2wire from AT&T in a room upstairs and use it as place I can plug in the Ethernet cords and also transmit another signal. I have what's a called plug link that is plugged in down stairs and then another upstairs and it allows the Internet signal to run through the power lines. So it just about the equivalent of running a cord for down stairs to upstairs. So basically I just need to plug more then 1 thing upstairs that isn't wireless and I would also like to transmit a 2.4ghz signal upstairs and use my Motorola to transmit a 5ghz.How would I set up the 2wire to do this.
View 3 Replies View Relatedwhat to do with my router cdr -king i cant access 192.168.1.1 in second time. i access it for the first time but i forgot to configure password now i cant connect using ID:admin Pass:admin
View 2 Replies View Relatedhow to create a password to access one pc to another pc .like i have 3 pc it is connecting throw switch .ip addresss is 192.168.1.1,192.168.1.2, 192.168.1.3 i want access from 192.168.1.1 to \192.168.1.2 like this here i want to create login password and how to remove password
View 1 Replies View Relatedi have a LAN network between several pc's connected with several switch's and connected to Thomson SpeedTouch 510 DSL Router its ip address is 10.0.0.100 subnet 255.0.0.0 and the router dont give auto ip to the PCs i have to issign it manually to the PCs "static ip".I bought the acer android recently so i bought a tp-link td-w8901g wireless router to act as an access point so i connected the 2 routers to each other by LAN and gave the tp-link an ip address 10.0.0.12 subnet mask 255.0.0.0 so it will be the same ip range of the speedtouch and setuped the tp-link router to fit my isp configeration it worked at first but i had to reset the router so i did the same configuration i did before but didnt work and i cant access the internet using the android or the wireless but when i connect the phone to the tp-link and unplug the speedtouch the wireless works so theres no any problem with the router?
View 1 Replies View RelatedI have a Netgear router which feeds an Eugenius ecb3500 Wireless Access point. I did not install the access point. I need to password protect our wireless environment, and that needs to be done on the Engenius. However, though I have tried many ways to access that device, I cannot. I cannot get an IP address for it,either. When I plug it directly in to my laptop (Win7), and type in the command line ipconfig, I get the IPv4 addresses of my laptop's local and wireless LAN card. How to get into the Engenius access point and password protect it?
View 1 Replies View Relatedi cant create dlink acess point password , if I am going 192.168.0.50 then showing error massages , I am check two three computer , then the same error coming
View 1 Replies View RelatedRecently I have purchased two brand new wap4410n access points.
I have connected my computer directly to one of the access points, and attempted to connect to the Web Configuration utility through my web browser.
I'm using a: 09' MacBook Pro, running Snow Leopard and Safari 5.
I can access the login screen of the access point, although when I enter the default username: admin and password admin, the login screen returns an error: Invalid username and/or password (or something to that effect). The URL changes to: http://192.168.1.245/login.htm&no=3.
I have reset the device by holding in the reset button for thirty seconds, powered down, powered up and re-attempted to login.
I still get the same error as above.
I have attempted to access the Web Configuration utility on both access points, and both access points provide the same error. I have also tried using the username: cisco and password: cisco.
Cisco, when contacted, said both access points must be faulty and I should replace them.
The probability of such an occurrence happening with two devices seems very low, and leads me to think there must be other factors at play. The only constant I can think of is the fact I'm using the same computer to access the devices.
I simply need to recover an embeded access point password.
I have the passwords to the 881-w router, but passwords to the embedded access point I don't have.
What is the recovery process for it, or the password reset process for the embedded access point.
I have a wireless router at home and i have a PC and a mac enabled for it. I have recently bought an IPAD and i can't connect for some reason. When asked for the password it doesn't enable me to connect so I'm worried that i've forgotten my password.
View 4 Replies View RelatedI don't remember the password for my wireless router.
View 4 Replies View RelatedThe wireless router PW has been changed, I got the new one correct but upon entering it on my laptop it goes around circle showing,"Wireless network detected" and then,"Unable to connect to preferred wireless network"It never works. I don't know how to fix this problem. It did not happen on my iPad.
View 2 Replies View Relatedi want to change my username and password of my router cw-5354 of cd-r king but the default user and password doesn't work anymore so i can't access the control panel.
View 3 Replies View Relatedi have access point but no security code where do i find this?
View 1 Replies View RelatedI need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedI'm having some difficulties with the VLAN setup on the SG-200 and the WiFi access point. The access point (a TP-Link WA801N) is only able to access the internet when it is plugged into a port that is on the default VLAN (PVID 1). If I plug it into one of the other VLANs then any clients connected to the WiFi lose access to the internet and cannot access devices on the VLAN. I have previously used this setup with a first generation Cisco WAP4410N. [code]
View 4 Replies View Relatedhow to installs 3 router with same password
View 2 Replies View RelatedI have taken over maintenance of a customer site from another service provider. I need to reprogram several WAP54G units. I have reset the units with the reset button. However, this does not reset the admin password back to admin.
View 9 Replies View RelatedI've got a 1941W, and we don't have the password for the access point. I've got access to the router, but not the access point.It's not the default password (cisco) and it's setup to use username/password (rather than just password).How do i reset this device? I'd like NOT to lose the config if possible.
View 1 Replies View RelatedMy son is using the above access point on his laptop. He wants to make the connection secure by having a password that you must enter in order to access it. How does he set up this password? Looked at the user manual; see the screens but don't know how to get to the screen.
View 2 Replies View RelatedI set up the WAP610N as a wireless access point, and it refuses to accept the passsword on several iphones (2 iphone4s and one iphone5) and a kindle fire.
The devices are picking up the network, but when the password is entered, the access point refuses the password. I've checked the password numerous times and the spelling is correct.
If the access point's settings are set to no security, there's an instant connection, which I expected, but the password is refused on either of the secure settings.
I bought the WAP610N for my son months ago, but he couldn't get it installed in his old apartment several states away because he doesn't have a CD drive in his computer. Now that he's moved into an apartment close to home, I was able to set it up using my computer. So I don't know if maybe it's a firmware issue since it sat in the box for months, or something else.
The access point is hooked up through a TP-Link TL-R860 Cable/DSL Router., which is not wireless.
How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View RelatedCan 2 N300 wireless bridges be connected to the same wireless access point ?
View 1 Replies View RelatedI lost my 192.168.1.1 password and how to reset it?
View 1 Replies View RelatedI had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies View RelatedI am having trouble connecting the Amped Wireless AP600EX access point to my WRSV4400n. As soon as I plug the range extender into the router, instead of it receiving an IP address, it crashes the router. I have updated the router firmware to 2.021. I have checked the box in the WDS menu to "allow wireles signal to be repeated". I will check with Amped, but are there any known issues between this router and the Amped Wireless family of range extenders?
View 1 Replies View RelatedHow we connect two different access point to each other
View 1 Replies View Relatedcannot get acess to router to put a password with 192.168.1.1 and my default gateway showing 2002:c058:6301::c058:6301
View 11 Replies View RelatedI can't find my netgear password
View 1 Replies View RelatedI lost my router 192.168.1.1 password and how to recover?
View 3 Replies View RelatedI have tried to reset linksys router and tried to use the IP address with an error message. We need to add another laptop to our network
View 1 Replies View Related
