I would like to as you that i have swiches 2960 (10Unit) and switches 3560 ( 3 unit) and router 2821 ( 1 unite) and AP( 10 unit).So do you know software can manage all those product? Like monitor switch up or down, manage configure, check performance.
View 3 RepliesI have more than 20 Cisco switches in my office which is basically a soap manufacturing factory. The switches include Cisco 2950, 2960, 3560, 3750 etc. We have routers also which include 2821, 2951 etc. We also have Cisco WLC 2125 and LAP 1262 series. Sometimes all these devices management comes very tough to us.
We need to log on to different devices for troubleshooting/network management which sometimes becomes very tough to us. So I wonder if there any Cisco applications or tools by which we can centrally manage all these devices.
i have got 5 catalyst :
Cisco Catalyst WS-C2960G-24TS-S
version 12.2 (53) SE
Image : C2960S-UNIVERSALK9-M
and i can 't configure the switch with Cisco Network Assistant. I have got this error : "unsupported device".
it is not possible to configure this model with CNA ?
I have a client whom has asked me to enable web management on some of his 2960 switches. I did not think this was going to be an issue, and so I told the customer I would set this up for him.
Much to my dismay, I have been able to get http and https enabled, and then authenticating locally for the HTTP access. I then come to the screen once authenticated which is shown below:
The issue is that when I select "Web Console", it gives me a "Web Page Cannot be found".
For my Lan, I have created two Vlan; Vlan 10 = for Users and Vlan 20 = For Database Servers,There are 15 Lan computer/laptop and 5 SQL database server (Dell Server) connected through same 24 port cisco 2960 switch. Means, 15 + 5 port occupied.
I have applied access list on cisco switch to restrict communication between vlan 10 and vlan 20.But My main purpose to create two Vlan is not for any kind of communication or restriction. My main Purpose is that Users traffic do not distrub or choke or affect the Database servers. then what will i need to do for that is VLAN Concept is sufficient for my concern OR I will need to buy seperate Cisco Switch to connect 5 database servers OR Else ?
I have an existing stack of 4 x 2960-S switches connected by stack cables.I would like to add another 2960-S switch to the stack but am unable to as the 2960-S will only allow 4 x 2960-S switches per stack.how I would add the 5th 2960-S switch to the existing stack of 4 x 2960-S switches.
View 12 Replies View RelatedMgmt Vlan 1 (default) Data VLan 10 (with access to internet) Is there a way to have a PC attached to a SG300 switch such that it can both access Vlan 10 for data and Vlan 1 for managment ? The PC's port clearly needs to be untagged PVID on vlan 10. I have tried adding vlan 1T and setting the port as a trunk port but to no avail, The switch is currently level 2. I am guessing this might not be possible in level 2 without setting the mgmt vlan to 10 ?.
View 3 Replies View RelatedI have VOIP and was provided a modem, a Tilgen Router (Vood 452_A). I also currently have a Linksys WRT54G router. I also have a home surveillance system with a DVR that can be accessed via the net. I am trying to allow the ports to open so that traffic can navigate down to the DVR.My IPs:My VOIP has provided me with 6 static IP addresses. For sake of this issue they are:
67.xx.xxx.153, through .158My subnetmask is set to:
255.255.255.248My Settings:
The Modem is connected to world. To the modem I have the Tilgen Router connected. The Tilgen is set with an ip of .153 and the subnetmask listed above. DHCP is turned on and has IP range set for .154-.158. It is set in Bridge Mode with NAT and Firewall turned off. To that I have the WRTG54G router connected and assigned the router an Static IP of .154.. The cable is going into the Linksys WAN port.From a computer connected to a LAN port on the WRT54G, I see my public IP as .154, currently my internal IP is 192.168.1.15 so I believe I have to assign one of my Static IPs to this PC, however when I try to connect to the Linksys Router (.154) from the outside web, I am get a time out error. (also from a ping test.) My thoughts are to assign the Linksys to DHCP and use a range of .155-.158 to give each lan item a static IP. My question is will this work? Will each item in the network have its own IP and if I forward the port to the DVR that i needed, ie 80 for web client or 6100 for desktop client, will that forward through?Or do I set it to Router Mode and use the Tilgen to assign the ips.
On the Tilgen I also have an option for a DHCP relay or to turn off DHCP.
For clarification here is the setup chain
Broadband/DSL Line>>Tilgen Modem>>(LANPort1)Tilgen Router(LAN Port2)>>(WAN) Linksys(LANPort1)>>DVR/Computers
Found this walkthrough on setting the WRT54G into a Switch. If I did this, in theory the VOOD would assign those computers/dvr connected downstream via the WRT54G a static ip from my range set on the router. Then in theory I would not need to port forward port 80 since the DVR would be on its own public IP.?
I am trying to Port Forward HTTP: 80, but my Router wont let me and it keep giving me this error message Status: Port Range Overlap with Remote Management.I have a NETGEAR CG814GCMR Router, I need to add that port for setting up a Game private server online, but my router wont let me, how to fix it?
View 12 Replies View RelatedI have the E3000 wired/wireless router and want to be able to manage my two SLM2008 switches with 192.168.1.253 and .254. Following the guides with adding vlan 2 and tagging the ports in which the two switches are wired together disables my ability to manage them seperately. I have added the gateway on 192.168.1.1 to both switches and told them that management vlan is 2 but no luck accessing them still.
View 1 Replies View RelatedI have a 2960S switch and nine (9) 300 switches. I have three VLANs configured on them, data, voice and management. Each 300 has unique data and ovice VLANs corresponding to their locations. All of the 300 switches connect to the 2960 in a hub and spoke network topology via 802.1q trunks. I can access devices between switches on the data and voice VLANs fine from any other switch. My issue is that from any 300 switch I can access the 2960 management VLAN interface without a problem, but I can not access the 300 switch management VLAN that I am connected to from the CLI. I do not use the GUI at all for management.
View 22 Replies View RelatedIs it possible to run VTP V3 on 2950 and 2960 switches. If so what version of IOS supports V3? Our 2960s are running 12.2(25r)SEE1, and 2950s are running 12.1(22)EA4a. Neither of which supports v3.
View 3 Replies View Relatedhave few doudts on MIB file upload.
1) What will be the extension of MIB file ? *.mib or *.my
2) I am running with 12.2(25)SEB IOS .Is thre any dependency with IOS for downloading MIB file.
3)I have 3560 switch and 2960 switch. Is thre any difference in the MIB file extension.
I have to setup my first flex stack and wanted to make sure I do it right. I have the physical aspect of the stack down. From what I gathered I have to setup the master switch as the highest priority and then provision the other two switches. But I have configs on the other two switches, do I have to delete them? And do I have to setup individual ips for the two slave switches, because from what I saw the master switch is the only one with an ip address? The master switch is a poe 2960S-48LPS and the two other switches are 2960G-48TD
View 5 Replies View RelatedWe had a new building thats gone up and complete now and we're trying to get a ip phone working down that end of the school on a vlan. We seem to be having trouble with the VLAN going through on the 2960 switch but it works fine on our core 3560 switch.
There looks like a slight variation in the config of the switches, the 3560 switch supports the "switchport trunk encapsulation dot1q" command on the interface where as the 2960 doesn't support the "switchport trunk encapsulation dot1q". Is this why the vlan is working on the 3560 and not the 2960, or is it something else?
Both switches are using the 12.2 IOS
Heres the trunk port configured on the 3560 going down to the new building and connecting into the 2960 with a 1gbit fiber link
interface GigabitEthernet1/2 description 3560X Port UpLink as Trunk Mode switchport trunk encapsulation dot1q switchport mode trunk udld port storm-control broadcast level 60.00 spanning-tree guard root
Heres the trunk port configured on the 3560 going to a Linksys switch which then connects to the DHCP server (The other end of the 3560 is also configued as trunk)
interface GigabitEthernet0/6 description Edge Switch port for clients switchport trunk encapsulation dot1q switchport mode trunk spanning-tree portfast
Heres the working vlan port on the 3560, the ip phone is able to get an ip and ring all other phones etc
interface GigabitEthernet0/7 description Edge Switch port for clients switchport access vlan 2 switchport mode access spanning-tree portfast
Ok now heres the config for the 2960
Heres the trunk port configured on the 2960 going back upto the 3560 switch
interface GigabitEthernet1/0/25 description Port UpLink as Trunk Mode switchport mode trunk udld port storm-control broadcast level 60.00
Heres the access port configured on the 2960 which isn't passing on vlan information. Is there another command i need to use to enable encapsulation as dot1q?
interface GigabitEthernet1/0/19 description Edge Switch port for clients
switchport access vlan 2 switchport mode access spanning-tree portfast
I am unable to input the command "ip flow-cache timeout active 1" to my cisco 2960 and 4948 switches. But i am able to do so in my cisco 6500 series switch. Hence how do i enable netflow on both 2960 and 4948 devices?My 2960 and 4948 are L3 switches. What commands or additional hardware module are required.
View 4 Replies View RelatedWe have 3 layer LAN architecture, layer 1 of 6500(IP routing), layer 2 of 4500(L2 switch only), layer 3 of 2960(L2 Switch)In a Single (2960 and 4500) Switch Port Avaya IP phone and PC are connected.Now, the requirement is that, Qos need to be configured for Voice traffic and Data traffic should be in default class of service.We plan to use COS value in Switch 4500 and 2960. We made a sample configuration as below
### For 4500 Switch
class-map match-all VOIP-Access-2MB
match cos 3 5
class-map match-all VOIP-Uplink-20MB
match cos 3 5
[code].....
check these configurations are correct as per standard and if there is any other method of configuration?What need to be configured in L3 Switch(6500)??In 2960, it doesn't support ingress QoS, what impact it will make when compare to 4500? do users experiance any difference?
We're testing the reference system shown in the figure below. System Description Four 2960 switches are used for transport;Equipment 1 and Equipment 2 exchange packets for synchronization;To reach synchronization Equipment 1 and 2 must exchange data with a very low jitter. 2960 Configuration details Four our test puprose, we're using 100Mbit/s ports (22 and 23) as trunk.In order to obtain minimum jitter We performed these configurations:We Enabled QoS;We Marked Synchronization packets with CoS 7 and DSCP 63;We marked other kind of traffic inserted in different ports) with CoS 0;We set "trust DSCP" on trunk ports;On the trunk ports we mapped traffic with CoS 7/DSCP 63 (and only this) on output queue 1;We enabled the expedite queue (priority-queue out). QuestionWith these settings we aim at forcing our synchronization packtes to precede other kind of traffic and go from Equipment 1 to Equipment 2 with minimum jitter.Unfortunately we experienced high jitter when both synchronization packets and other traffic are sent through the systems.
View 9 Replies View RelatedAre the non-S series 2960 switches stackable or are they only able to be uplinked?
View 6 Replies View RelatedI have a problem I have Cisco 2960 series switches with ip address 10.10.10.2 255.255.255.0 works but can not connect to the Internet
View 1 Replies View RelatedI have a 2960 and a 2811 with a hwic card I have one port set as 100 meg and another port set at 10 meg. Both are set to access mode. i need one port for failover (10 meg) . I can't do ether channel on the hwic. How do I prevent a loop when I connect my second connection. While having both connections up. Should I use bpdu guard? the goal is to have one port fail over if the 100 meg goes down. And I'm currently running ospf so it should take the faster connection.
View 1 Replies View RelatedI have a Catalyst 2960 switch (2960-8TC-L) and running Software version 12.2(53)SE1.I mange to configure SSH to the switch and add addition user as well.Now I need to configure this switch password less log in with public key SSH authentication.
I configured several Linux servers and Workstations for the public key SSH authentication.So far I could not figure out how to do this in CISCO switch. Following link {URL} how to do this.But ip ssh pub key- chain command never work showed invalid command.
Thinking of getting one of those 8-port 2960 for a CCNP study. Is the difference between the C2960-8TC-S and the C2960-8TC-L models in Hardware, or in IOS? or both? And if it's in IOS, is the S upgradable to L?
View 7 Replies View RelatedCompany I work for just moved into a new location. We have two data closets which are patched as independent entities, with no Ethernet tie connection. These closets are roughly 100 feet apart.
There is a fiber connection that runs between both closets, that the previous tenant used to connect the switches. I have placed a Cisco 2960 switch in each location, and added one mini SFP gbic's to each switch. After attaching both sides, neither light up. I do a sh inter gig1/0/49 on each and shows 'down down' (not admin down).
What is the trick on getting these to communciate, do I need to configure these ports, and are they supposed to light up?
What I am trying to accomplish is to get the one closet that is completely cut off, communicating by logically stacking, or 'daisy chaining' via fiber.
I turned off the lights and popped the fiber out, and I do see a faint red light (I did not look straight into it), so I think the fiber is active.
I have 4506e core switch to which 10 other 2960 switches are connected.I want to upgrade thier IOS. how can upgrade it, can I upgrade it one by one or all at a time?
Is there any tool to perform this task?
I am having a problem in connecting two Cisco 2960 Switches between two different buildings using Cisco WLC 2504 & 3 Wireless 1552S APs.
- One AP is directly connected to Switch - 1 where WLC is connected and serving as a RAP
- Another one is working as Mesh in the field.
- Third one is a Mesh Access Point wired to another Switch - 2. (Bridging is enabled)
All the APs, WLC & switches are in the same network 10.3.x.x subnet mask : 255.255.240.0?WLC is working with default management interface whereas switches are having VLAN1 configured as default VLAN.All the port for the switches are Trunk ports?Once i am trying to ping the RAP or any MAP from Switch - 1 I am sucessful but once i am pinging Switch - 2, its not replying. Similar is that case from Switch - 2 side.
I have a number of 2960 switches that have crashed without any reason
Under show version System returned to ROM by address error at PC 0x108971C, address 0x0
I am implementing QoS on our MPLS network. Our environment exists of a mix of Cisco 2960 and 3560 switches. The IPT system is Avaya CM with Avaya phones.The WAN network is a MPLS network.Ports are configured for access and voice vlan (no trunking), one vlan for voice, one for data (vlan 1 is disabled).I dont have Qos coonfigured on LAN just wanted to configure on WAN Router where my Mpls link is connected.I have 45 Mb Mpls links on all sites connected to each other.
I have multiple sites connected via MPLS and i have control at both sides.Current config is mentioned below in which DSCP marking is not done for signaling. What is the best config with example.Current Config on all Cisco Router where MPLS link is terminated at all sites. [code]
I am aware that private-vlans are not supported on edge switches like 2960 series - so my question is would it be possibel to ceate private vlans on say just the core switch which would be a 3570 or 4506 that supports private vlans and then just trunk these to the edge like normal vlans?what I need to achive is to have edge port not able to communicate to each other even across switches - which cannot be done using 'protected' port so need the private vlan feature?
View 1 Replies View RelatedI have a customer with Cisco 7940 and 7960 IP phones that they do not plan to replace. They do want a new LAN and are looking at the Catalyst WS-C2960S-48FPD-L and WS-C2960S-24PD-L as access layer devices.
these switches support the Cisco pre-standard PoE required by the 7940 and 7960 IP phones.
Any one who knows where I can find a documentation where it says the maximum switches per stack for the Catalyst 2960 family?
View 2 Replies View RelatedWe ordered 4x cisco 2960 switch with LAN Lite software by mistake. Can we upgrade them to Lan Base?When I change boot image I get Error: hardware not supported by firmware.
View 3 Replies View RelatedI need to connect 4 Floor Building with 4 Cisco 2960 - 48 ports switch each other and it needs to be through a fiber. So all PCs connected to each switch would reach the LAN/WAN from the other switch. (attached is the image here with)
I see that the 2960 has 2 SFP ports each port of each switch should connect each other or how?
My simple question is:
1. What cable / patch code I have to use = Single-mode or Multimode? ( distance for each switch will not more then 25 mts)
2. Do I have to use SFP or SFP+ module?
3. What kind of SFP/SFP+ module I have to use = Single-mode or Multimode?
4. What kind of connector should patch code have = LC / SC or ?
5. How to connect each switch with redundancy like ...each switch should be interconnected with each other or I have to choose Cisco 3750G which has more then 2 SFP ports (option#1 & opetion#2 = attached here with) =
Best practice for connecting cisco switches over fiber.