Cisco WAN :: Possible To Run VTP V3 On 2950 And 2960 Switches

Jan 2, 2013

Is it possible to run VTP V3 on 2950 and 2960 switches. If so what version of IOS supports V3? Our 2960s are running 12.2(25r)SEE1, and 2950s are running 12.1(22)EA4a. Neither of which supports v3.

View 3 Replies


ADVERTISEMENT

Cisco Switching/Routing :: Private Vlans Across 2960 / 2950 Switches?

Nov 12, 2012

I am aware that private-vlans are not supported on edge switches like 2960 series - so my question is would it be possibel to ceate private vlans on say just the core switch which would be a 3570 or 4506 that supports private vlans and then just trunk these to the edge like normal vlans?what I need to achive is to have edge port not able to communicate to each other even across switches - which cannot be done using 'protected' port so need the private vlan feature?

View 1 Replies View Related

Linksys Wired Router :: Vlan Trunking 2960 And 2950 Switches

Feb 18, 2011

I have a number of class-'c's as a hand-off from my data center fiber to my 2960, which then sprawls the racks with about many 2950 switches, mostly 20 machines per switch. To allow machines on one 2950 to push data to another 2950 without routing back to my ISP's router(which costs money for bandwidth) isn't is possible to trunk one port on each 2950 to another 2950 and adding a addititional vlan8 to them. Then data jumps from 2950 to 2950 without going back to the 2960 or mainly not going back to my ISP's router.  Is this the correct way to accoplish this with extra vlan and trunking the 2950's to each other or am I looking at this all wrong?

View 1 Replies View Related

Cisco Switching/Routing :: Enable Multicast On 2950 / 2960 Series Switches?

Dec 8, 2011

How do you enable multicast traffic on 2900 series switches?

View 7 Replies View Related

Cisco :: 2950 / 2960 / 3560 / 3750 / 2125 / 1262 - Centrally Manage All Switches

Aug 27, 2012

I have more than 20 Cisco switches in my office which is basically a soap manufacturing factory. The switches include Cisco 2950, 2960, 3560, 3750 etc. We have routers also which include 2821, 2951 etc. We also have Cisco WLC 2125 and LAP 1262 series. Sometimes all these devices management comes very tough to us.
 
We need to log on to different devices for troubleshooting/network management which sometimes becomes very tough to us. So I wonder if there any Cisco applications or tools by which we can centrally manage all these devices.

View 2 Replies View Related

Cisco :: 2950 / 2960 - LMS Config Deployment With New Device

May 20, 2013

I have recovered some configuration files from my 2950 switches with the Configuration Archive Tool in LMS.
Now, I'd like to replace my old 2950s by 2960 switches, which have the same number of ports.
 
Will there be any issue if I copy the exact same config from 2950 to 2960 ? Will some features not work or is everything interoperable ? Here's an extract of the config :
 
Global
version 12.1
no service pad
service timestamps debug  date time
service timestamps log date time
no service password-encryption
[ code]....

View 2 Replies View Related

Cisco Switching/Routing :: DHCP Server Will Work On 2950 / 2960 Switch

Feb 11, 2012

With out using any server, will DHCP be configured in cisco 2950/2960 switch?I man cisco it self should work as a dhcp server also.

View 10 Replies View Related

Cisco Switching/Routing :: Add 2960 To Stack Of 4 X 2960 Switches

Feb 7, 2012

I have an existing stack of 4 x 2960-S switches connected by stack cables.I would like to add another 2960-S switch to the stack but am unable to as the 2960-S will only allow 4 x 2960-S switches per stack.how I would add the 5th 2960-S switch to the existing stack of 4 x 2960-S switches.

View 12 Replies View Related

Cisco :: Difference Between 2950 And 2950c Switches

Nov 13, 2012

What is the difference between the 2950 and 2950c switches? I tried finding it on the feature navigator but I couldn't. And I wasn't able to get anything from the Cisco website either. (I didn't really look through the long PDFs, I'm sure there is a more simple way to find the answer to this that I'm not aware of.)

View 3 Replies View Related

Cisco Infrastructure :: Etherchannel Between Two 2950 Switches

Dec 7, 2011

I have a etherchannel defined between 2 L2 switches using LACP as shown below. The etherchannel works fine, however when I hard code speed/duplex on both ends the etherchannel fails. What is causing this behaviour?
 
SW02:
interface Port-channel5
interface GigabitEthernet1/0/1
switchport mode trunk

[Code]....

View 6 Replies View Related

Cisco Switching/Routing :: 2950 / NIC Teaming On Two Switches?

Apr 25, 2013

I have a server windows 2008 that I would like to have a nic teaming configuration, the server has two nics, each nic is connected to a different switch. One is connected to cisco 2960 and the other is connected to cisco 2950. I have read here in forums about nic teaming but using the same switch. I have not found using different switch. Is this possible?

View 1 Replies View Related

Cisco Infrastructure :: 2950 - Implement IP SLA On Layer2 Switches?

May 24, 2006

I am trying to implement IP SLA. Can I implement it on layer2 switches?

View 5 Replies View Related

Loud Fans 2950 Switches Lab Environment

Feb 4, 2013

I'm having some serious sound problem with some 2950 Cisco switches that I have in my CCNA lab these switches sound like a jet I've gone in and made sure the fans are clean and I even replaced one they still are too loud. So I have a few options I can run them without a fan which I really don't want to do but I want to look at two other options. The first option would be to put a heat sink on the chip that's producing heat I also thought about cutting a whole in the top and mounting a 120mm fan.

View 4 Replies View Related

Cisco Switching/Routing :: Trunking Between Catalyst 2950 Switches?

May 14, 2012

have setup a small lab as per CBTNuggets. Everything was going well until I introduced a second switch to create a trunk. Now I cannot ping between my two switches. Both show operational mode as down:
 
SWITCH1#show interfaces f0/12 switchport
Name: Fa0/12
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: down
Administrative Trunking Encapsulation: dot1q

[code]....
 
I have tried to allow all vlans or vlan 1 specifically and the output of the above doesn't seem to change. I am wondering if there is something in the config-register that is preventing trunking, but I don't really know enough yet!

The output of my second switch is identical to this one, the only difference is that I have it configured as a vtp client.

View 4 Replies View Related

Cisco Catalyst 2950 - GigE Switches With 64bit IF-MIB SNMP Counters?

Oct 18, 2011

which models of HP ProCurve or Dell PowerConnect support 64-bit IF-MIB counters, or for that matter any other manufacturer (Zyxel?) (snmpv2 or v3, OID .1.3.6.1.2.1.31.1.1.1.6)I believe pretty much any Cisco Catalyst above a 2950 do, however don't believe any of the SG series do. I realize I could pick up a 2960G for $1500-2k and be good to go, but I forsee a larger switch purchase in the future, but still could use a switch in the meantime that was able to allow accurate monitoring of closet uplink bandwidth?

View 1 Replies View Related

Cisco Switches :: Configuring 2960 And 300 ES Switches?

Jul 26, 2012

I have a 2960S switch and nine (9) 300 switches. I have three VLANs configured on them, data, voice and management. Each 300 has unique data and ovice VLANs corresponding to their locations. All of the 300 switches connect to the 2960 in a hub and spoke network topology via 802.1q trunks. I can access devices between switches on the data and voice VLANs fine from any other switch. My issue is that from any 300 switch I can access the 2960 management VLAN interface without a problem, but I can not access the 300 switch management VLAN that I am connected to from the CLI. I do not use the GUI at all for management.

View 22 Replies View Related

Cisco Switching/Routing :: 2950 - Private VLAN Across Trunk To Older Model Switches

Mar 7, 2012

I am looking into the possibility of using private vlan's for some dmz implementations however I do have what may be some very rudimentary questions. It seems straightforward how to configure the primary/secondary vlan configuration as well as associating them. However in my case I would be looking to configure the PVLAN on a 6500-vss platform acting as the router while all of the hosts which I would desire to have in the isolated vlan would be spread out across a number of older Cisco switches which only support "protected port" setup or Procurve switches all of which I do not have budget to replace with something newer. So in my scenario I would have a 6500 connected by trunk to multiple switches which only support a protected port setup such as a Procurve (top of rack) or a Cisco 2950. As the Procurve or 2950 would not support Private VLAN setup, do I then just configure the secondary vlan to be allowed across the trunk from the 6500, configure that vlan on the Procurve or 2950 (as vtp will not foward the info for the secondary vlan) and assign that vlan to the host port as well as setting it as a protected port and this will communicate just fine across the trunk to the router as well as stopping the protected port in top of rack switch 1 from being able to communicate to a protected port in top of rack 2,3,etc? If the above scenario is what needs to be done, do I just use a regular trunk or do I have to use a PVLAN trunk?

View 2 Replies View Related

Cisco Switching/Routing :: 2950 / 3560 / Chart To Show What Modules Will Fit What Switches For Fiber Applications

Dec 12, 2011

Is there a chart to show what modules will fit what swithches for fiber applications ex 2950 and 3560 switches

View 1 Replies View Related

Cisco :: How To Manage Many 2960 Switches

Oct 3, 2011

I would like to as you that i have swiches 2960 (10Unit) and switches 3560 ( 3 unit) and router 2821 ( 1 unite) and AP( 10 unit).So do you know software can manage all those product? Like monitor switch up or down, manage configure, check performance.

View 3 Replies View Related

Cisco :: MIB For 3560 And 2960 Switches

Nov 30, 2011

have few doudts on MIB file upload.
 
1) What will be the extension of MIB file  ? *.mib or *.my
2) I am running with 12.2(25)SEB IOS .Is thre any dependency with IOS for downloading MIB file.
3)I have 3560 switch and 2960 switch. Is thre any difference in the MIB file extension.

View 1 Replies View Related

Cisco WAN :: Set Up Flex Stack On 2960 Switches?

Jul 15, 2012

I have to setup my first flex stack and wanted to make sure I do it right.  I have the physical aspect of the stack down.  From what I gathered I have to setup the master switch as the highest priority and then provision the other two switches.  But I have configs on the other two switches, do I have to delete them?  And do I have to setup individual ips for the two slave switches, because from what I saw the master switch is the only one with an ip address?  The master switch is a poe 2960S-48LPS and the two other switches are 2960G-48TD

View 5 Replies View Related

Cisco WAN :: VLAN On 2960 And 3560 Switches

Apr 10, 2011

We had a new building thats gone up and complete now and we're trying to get a ip phone working down that end of the school on a vlan. We seem to be having trouble with the VLAN going through on the 2960 switch but it works fine on our core 3560 switch.
 
There looks like a slight variation in the config of the switches, the 3560 switch supports the "switchport trunk encapsulation dot1q" command on the interface where as the 2960 doesn't support the  "switchport trunk encapsulation dot1q". Is this why the vlan is working on the 3560 and not the 2960, or is it something else?
 
Both switches are using the 12.2 IOS
 
Heres the trunk port configured on the 3560 going down to the new building and connecting into the 2960 with a 1gbit fiber link
 
interface GigabitEthernet1/2 description 3560X Port UpLink as Trunk Mode switchport trunk encapsulation dot1q switchport mode trunk udld port storm-control broadcast level 60.00 spanning-tree guard root
 
Heres the trunk port configured on the 3560 going to a Linksys switch which then connects to the DHCP server (The other end of the 3560 is also configued as trunk)
 
interface GigabitEthernet0/6 description Edge Switch port for clients switchport trunk encapsulation dot1q switchport mode trunk spanning-tree portfast
 
Heres the working vlan port on the 3560, the ip phone is able to get an ip and ring all other phones etc
 
interface GigabitEthernet0/7 description Edge Switch port for clients switchport access vlan 2 switchport mode access spanning-tree portfast
 
Ok now heres the config for the 2960
 
Heres the trunk port configured on the 2960 going back upto the 3560 switch
 
interface GigabitEthernet1/0/25 description Port UpLink as Trunk Mode switchport mode trunk udld port storm-control broadcast level 60.00
 
Heres the access port configured on the 2960 which isn't passing on vlan information. Is there another command i need to use to enable encapsulation as dot1q?
 
interface GigabitEthernet1/0/19 description Edge Switch port for clients
switchport access vlan 2 switchport mode access spanning-tree portfast

View 11 Replies View Related

Cisco :: Enabling Net Flow In 2960 And 4948 Switches

Aug 26, 2012

I am unable to input the command "ip flow-cache timeout active 1" to my cisco 2960 and 4948 switches. But i am able to do so in my cisco 6500 series switch. Hence how do i enable netflow on both 2960 and 4948 devices?My 2960 and 4948 are L3 switches. What commands or additional hardware module are required.

View 4 Replies View Related

Cisco Switching/Routing :: QoS In L2 Switches 2960 And 4500?

Mar 12, 2013

We have 3 layer LAN architecture, layer 1 of 6500(IP routing), layer 2 of 4500(L2 switch only), layer 3 of 2960(L2 Switch)In a Single (2960 and 4500) Switch Port Avaya IP phone and PC are connected.Now, the requirement is that, Qos need to be configured for Voice traffic and Data traffic should be in default class of service.We plan to use COS value in Switch 4500 and 2960. We made a sample configuration as below 
 
### For 4500 Switch
 class-map match-all VOIP-Access-2MB
  match cos  3  5
class-map match-all VOIP-Uplink-20MB
  match cos  3  5

[code].....
 
check these configurations are correct as per standard and if there is any other method of configuration?What need to be configured in L3 Switch(6500)??In 2960, it doesn't support ingress QoS, what impact it will make when compare to 4500? do users experiance any difference?

View 1 Replies View Related

Cisco Switches :: 2960 / Priority Queue Out Handling?

Mar 6, 2012

We're testing the reference system shown in the figure below. System Description Four 2960 switches are used for transport;Equipment 1 and Equipment 2 exchange packets for synchronization;To reach synchronization  Equipment 1 and 2 must exchange data with a very low jitter. 2960 Configuration details Four our test puprose, we're using 100Mbit/s ports (22 and 23) as trunk.In order to obtain minimum jitter We performed these configurations:We Enabled QoS;We Marked Synchronization packets with CoS 7 and DSCP 63;We marked other kind of traffic inserted in different ports) with CoS 0;We set "trust DSCP" on trunk ports;On the trunk ports we mapped traffic with CoS 7/DSCP 63 (and only this) on output queue 1;We enabled the expedite queue (priority-queue out). QuestionWith these settings we aim at forcing our synchronization packtes to precede other kind of traffic and go from Equipment 1 to Equipment 2 with minimum jitter.Unfortunately we experienced  high jitter when both synchronization packets and other traffic are sent through the systems.

View 9 Replies View Related

Cisco Switching/Routing :: Are Non-S 2960 Switches Stackable

Jul 5, 2012

Are the non-S series 2960 switches stackable or are they only able to be uplinked?

View 6 Replies View Related

Cisco WAN :: Switches 2960 Series No Internet Access?

Mar 29, 2011

I have a problem I have Cisco 2960 series switches with ip address 10.10.10.2 255.255.255.0 works but can not connect to the Internet

View 1 Replies View Related

Cisco WAN :: 2960 / 2811 - Connecting 2 Ports With Two Switches

May 18, 2012

I have a 2960 and a 2811 with a hwic card I have one port set as 100 meg and another port set at 10 meg. Both are set to access mode. i need one port for failover (10 meg) . I can't do ether channel on the hwic. How do I prevent a loop when I connect my second connection. While having both connections up. Should I use bpdu guard? the goal is to have one port fail over if the 100 meg goes down. And I'm currently running ospf so it should take the faster connection.

View 1 Replies View Related

Cisco Switches :: 2960 - Password Less Log In With Public Key SSH Authentication

Apr 13, 2010

I have a Catalyst 2960 switch (2960-8TC-L) and running Software version  12.2(53)SE1.I mange to configure SSH to the switch and add addition user as well.Now I need to configure this switch password less log in with public key SSH authentication.

I configured several Linux servers and Workstations for the public key SSH authentication.So far I could not figure out how to do this in CISCO switch. Following link {URL} how to do this.But ip ssh pub key- chain command never work showed invalid command.

View 2 Replies View Related

Cisco :: Difference Between Lite Entry And Base 2960 Switches

Jul 1, 2012

Thinking of getting one of those 8-port 2960 for a CCNP study. Is the difference between the C2960-8TC-S and the C2960-8TC-L models in Hardware, or in IOS? or both? And if it's in IOS, is the S upgradable to L?

View 7 Replies View Related

Cisco Switching/Routing :: Fiber Connection Between Two 2960 Switches?

Mar 22, 2012

Company I work for just moved into a new location.  We have two data closets which are patched as independent entities, with no Ethernet tie connection. These closets are roughly 100 feet apart. 
 
There is a fiber connection that runs between both closets, that the previous tenant used to connect the switches.  I have placed a Cisco 2960 switch in each location, and added one mini SFP gbic's to each switch.  After attaching both sides, neither light up.  I do a sh inter gig1/0/49 on each and shows 'down down' (not admin down).
 
What is the trick on getting these to communciate, do I need to configure these ports, and are they supposed to light up? 
 
What I am trying to accomplish is to get the one closet that is completely cut off, communicating by logically stacking, or 'daisy chaining' via fiber. 
 
I turned off the lights and popped the fiber out, and I do see a faint red light (I did not look straight into it), so I think the fiber is active.

View 2 Replies View Related

Cisco Switching/Routing :: 2960 Switches - IOS Upgrading For 4506e

Jul 21, 2012

I have 4506e core switch to which 10 other 2960 switches are connected.I want to upgrade thier IOS. how can upgrade it, can I upgrade it one by one or all at a time?
 
Is there any tool to perform this task?

View 7 Replies View Related

Cisco Wireless :: Connect Two 2960 Switches In Two Separate Buildings?

Feb 22, 2013

I am having a problem in connecting two Cisco 2960 Switches between two different buildings using Cisco WLC 2504 & 3 Wireless 1552S APs.
 
- One AP is directly connected to Switch - 1 where WLC is connected and serving as a RAP

- Another one is working as Mesh in the field.

- Third one is a Mesh Access Point wired to another Switch - 2. (Bridging is enabled)
 
All the APs, WLC & switches are in the same network 10.3.x.x subnet mask : 255.255.240.0?WLC is working with default management interface whereas switches are having VLAN1 configured as default VLAN.All the port for the switches are Trunk ports?Once i am trying to ping the RAP or any MAP from Switch - 1 I am sucessful but once i am pinging Switch - 2, its not replying. Similar is that case from Switch - 2 side.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved