have few doudts on MIB file upload.
1) What will be the extension of MIB file ? *.mib or *.my
2) I am running with 12.2(25)SEB IOS .Is thre any dependency with IOS for downloading MIB file.
3)I have 3560 switch and 2960 switch. Is thre any difference in the MIB file extension.
We had a new building thats gone up and complete now and we're trying to get a ip phone working down that end of the school on a vlan. We seem to be having trouble with the VLAN going through on the 2960 switch but it works fine on our core 3560 switch.
There looks like a slight variation in the config of the switches, the 3560 switch supports the "switchport trunk encapsulation dot1q" command on the interface where as the 2960 doesn't support the "switchport trunk encapsulation dot1q". Is this why the vlan is working on the 3560 and not the 2960, or is it something else?
Both switches are using the 12.2 IOS
Heres the trunk port configured on the 3560 going down to the new building and connecting into the 2960 with a 1gbit fiber link
interface GigabitEthernet1/2 description 3560X Port UpLink as Trunk Mode switchport trunk encapsulation dot1q switchport mode trunk udld port storm-control broadcast level 60.00 spanning-tree guard root
Heres the trunk port configured on the 3560 going to a Linksys switch which then connects to the DHCP server (The other end of the 3560 is also configued as trunk)
interface GigabitEthernet0/6 description Edge Switch port for clients switchport trunk encapsulation dot1q switchport mode trunk spanning-tree portfast
Heres the working vlan port on the 3560, the ip phone is able to get an ip and ring all other phones etc
interface GigabitEthernet0/7 description Edge Switch port for clients switchport access vlan 2 switchport mode access spanning-tree portfast
Ok now heres the config for the 2960
Heres the trunk port configured on the 2960 going back upto the 3560 switch
interface GigabitEthernet1/0/25 description Port UpLink as Trunk Mode switchport mode trunk udld port storm-control broadcast level 60.00
Heres the access port configured on the 2960 which isn't passing on vlan information. Is there another command i need to use to enable encapsulation as dot1q?
interface GigabitEthernet1/0/19 description Edge Switch port for clients
switchport access vlan 2 switchport mode access spanning-tree portfast
I am implementing QoS on our MPLS network. Our environment exists of a mix of Cisco 2960 and 3560 switches. The IPT system is Avaya CM with Avaya phones.The WAN network is a MPLS network.Ports are configured for access and voice vlan (no trunking), one vlan for voice, one for data (vlan 1 is disabled).I dont have Qos coonfigured on LAN just wanted to configure on WAN Router where my Mpls link is connected.I have 45 Mb Mpls links on all sites connected to each other.
I have multiple sites connected via MPLS and i have control at both sides.Current config is mentioned below in which DSCP marking is not done for signaling. What is the best config with example.Current Config on all Cisco Router where MPLS link is terminated at all sites. [code]
I have more than 20 Cisco switches in my office which is basically a soap manufacturing factory. The switches include Cisco 2950, 2960, 3560, 3750 etc. We have routers also which include 2821, 2951 etc. We also have Cisco WLC 2125 and LAP 1262 series. Sometimes all these devices management comes very tough to us.
We need to log on to different devices for troubleshooting/network management which sometimes becomes very tough to us. So I wonder if there any Cisco applications or tools by which we can centrally manage all these devices.
I have an existing stack of 4 x 2960-S switches connected by stack cables.I would like to add another 2960-S switch to the stack but am unable to as the 2960-S will only allow 4 x 2960-S switches per stack.how I would add the 5th 2960-S switch to the existing stack of 4 x 2960-S switches.
View 12 Replies View RelatedI have a question regarding QOS and possibly dedicated bandwidth. The environment is ISP goes into an ASA that up links to a 3560 and fiber up links to other 2960s throughout the building for internet. My question is for certain sections of the building if I segment the network can I guarantee them a certain amount of bandwidth. For example, if 1 gigabit is coming into the building from the ISP and into the ASA, can I guarantee one room in the building no less than say 200 Mb of the full internet pipe at all times?
View 7 Replies View Related3560--------------------------2960 connects via single mode Fiber and now will have another redundant Link between 3560 and 2960 with Ethernet interface ( Wireless). 3560------------trunk config---------2960 < Fiber Link >
what config I need on Ethernet interface on 3560 and 2960?what config is needed to alwayz have fiber as primary connection and Wireless as backup.
From the multiplexer 9 ethernet connections are terminating in Cisco 2960G 24 port swith and it is connected through fiber uplink to one Cisco 3560G 48 port switch in first floor, which is connected to server.
How I will configure the 3560G to make communicate with 2960G and bring all these 9 ethernet connections to server. All the 9 connections are from different IP. and server also have different IP.
It seems my 2960s and 3560s switches have enough flash space and memory to support the 15.0 IOS should I be OK to jump to this from 12.2(35)?
View 10 Replies View RelatedIm trying to Connect a 2960-S Catalyst Switch to a 3560 Catalyst Switch. It worth pointing out im newish to switching although i know some commands and what they do This is my first time connecting 2 switches together.They are connected via a crossover cable and have green lights flashing on the connected ports When i run "show CDP neighbours it sees the new switch Unable to ping new switch...just timesout Here is the the interface on the 3650
GigabitEthernet0/40 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 001b.532f.8428 (bia 001b.532f.8428)
Description: Uplink to Switch 2
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
[code]....
I'm having issue with one stubborn process that is consuming nearly all the CPU on all of my switches. I tried googling it, but had no luck. The process is "hulc nrgyz PD di"
View 4 Replies View RelatedYesterday Cisco released IOS 15 code into the wild for the 2960 and 3560/3750 families but the link to the release notes is not working. Because I already have a whole bunch of 4500/Sup7's running IOS 15 I am thinking about taking the plunge with 30 3750-X's I have on order but want to review the release notes first. where they might be hiding?
View 4 Replies View RelatedI have CISCO RPS 600 (PWR-AC-RPS) is it support Catalyst 2960 and 3560 ? and which type of cable require since i have cable 22-18 pin and on my switch require 22-14 pin.
View 2 Replies View RelatedAs per my attached diagram, I have three switches (Cat 3560-E and couple of Cat 2960-G)
Each PC is on different vlan
PC -1 on vlan 100
PC-2 on vlan 200
I need to connect PC-1 and PC-2 to the server. Server has no fixed vlan and can be changed.
Restrictions:
1) can’t change PCs vlan assignment.
2) can’t add 2nd NIC in the server.
I’ve tried private vlan but it requires separate physical ports for host and/or community vlan and somehow it did not work. I could be wrong Trunking using dot1q enabled on port 2 on all switches and connection works fine (server to PC-1 or server to PC-2) by enabling switchport access vlan 100 or switchport access vlan 200. However I need port 5 on switch-1 to respond to vlan 100 and 200.
When did this wonderful feature get introduced? Is it going to moved down to the 3560s/2960s type switches?
View 0 Replies View RelatedI would like to test the possibility to reload devices via SNMP for new switches like 2960, 3560 and so on.I know that the command "snmp-server system-shutdown" has to be configured, then I need to send the set query to the device via SNMP.
I have found on the net the OID 1.3.6.1.4.1.9.2.9.9.0 but it belongs to an old MIB and doesn't seem to work with new switch models.
I know only one method to restart Cisco switch through Telent using command " RELOAD". How can we restart Cisco 2960/3560 switch phyically....can i use mode button to restart cisco switch ?
View 11 Replies View RelatedI want to implement port-based and MAC-based in these two switches: 2960 & 3560 (both of them have this IOS version: 12.2(55)SE1). And I haven't found a way to implement both of them at the same time. This is what I got:
ip dhcp use subscriber-id client-id
ip dhcp subscriber-id interface-name
ip dhcp excluded-address 192.168.0.0 192.168.0.2
ip dhcp excluded-address 192.168.0.251 192.168.0.255
[code]....
With this configuration I can use port-based, but not MAC based. If I remove the first two lines and change the last line for this one:
address 192.168.0.7 client-id 0112.ae1d.af58.60
Then, the computer with that MAC address got the correct IP, but then the port-based doesn't work. Also, I got this line in the interface what I want to use MAC-based:
ip dhcp server use subscriber-id client-id
Is it possible to daisy chain from a 3560 to 2960-S switch using a SFP interconnect cable (daisy chain cable)
View 1 Replies View Relatedlets you catalyst 3560 & 2960 remote login with a secure protocol
View 4 Replies View RelatedWe have quite a few 3560 & 2960 on our edge network - what I have been looking at was to access switches via web-interface i.e. web-browser. Only problem with this is it always gives you access on privilige level 15 which is not ideal as not all who we decide to give access to these switches will be admin and allowed to configure these swicthes - In the 3560/2960 data-sheet states:
"Alternatively, a local username and password database can be configured on the switch itself. Fifteen levels of authorization on the switch console and two levels on the Web-based management interface provide the ability to give different levels of configuration capabilities to different administrators"
Where as there is no mention of how to configure these two levels of Web-based management in the configuration guide.
As per the attached diagram: How do I configure the 2 ports on the 3560 (Ports 6 & 7) and the connected ports on each of the 2960 switches (Port 25) to provide redundancy.
If the up link from Switch A dies then I need the traffic to flow through the trunk and utilize the up link on Switch B with minimal delay (milliseconds).
I have a Cisco 3560 running as a Level3 device in my network running 10 V LANs and routing between most of them (nothing complex with ACLs) and running spanning-tree mode pvst. The main network is run on a net gear GS748TPS stack of three switches running MSTP.
I have just bought an additional 3560 and a 2960 to plug in. I have set them up with IP addresses and then plugged them into the net gear. This brought the whole network down until I unplugged the new switches.
I have confirmed the IP addresses aren't duplicated and that DHCP is not running on the switches so I can only assume it's something to do with DHCP. I cannot afford for the network to go offline again, so is there anything I should check? Am I running incompatible spanning tree methods between the net gear and Cisco devices?
I am using Packet Tracer to simulate Cisco networking.As the existing IOS of the 3560 and 2960 switch are in older version which has no new feature in new IOS, how to upgarde the IOS of Cisco switch at Packet Tracer?
View 5 Replies View RelatedI have a 2960S switch and nine (9) 300 switches. I have three VLANs configured on them, data, voice and management. Each 300 has unique data and ovice VLANs corresponding to their locations. All of the 300 switches connect to the 2960 in a hub and spoke network topology via 802.1q trunks. I can access devices between switches on the data and voice VLANs fine from any other switch. My issue is that from any 300 switch I can access the 2960 management VLAN interface without a problem, but I can not access the 300 switch management VLAN that I am connected to from the CLI. I do not use the GUI at all for management.
View 22 Replies View RelatedLooking for Information about Latest IOS Available for switch Series 3560, Guide the latest IOS sopprted Features Specification And Also Guide the Switch Minimum Hardware capacity Require to upgrade with the latest IOS.
View 2 Replies View RelatedI have been looking at deploying a small core switch design for an important branch office that would consist of 2 cores with an etherchannel link and then 4 POE access switches linked to both cores utilising STP. I will also want static IP routing on the cores and will set up HSRP for gateway failover.
The initial switch I looked at for the core was WS-C3560E-24TD-S however after finding that there is no stock around of this at the moment I have seen the WS-C3560X-24T-S which looks like it will do everything I need including IP routing, HSRP and QoS for VOIP. The thing that concerns me is this is about £1000 cheaper so i'm slightly worried im missing someting.
I have purchased two catalyst 3560 switches (with 24 interfaces) on Ebay to prepare for ccnp switch exam. It would be great if I have 4 switches. Is it any possibillity to create two logical switches from one? I mean, not by assigning interfaces to different vlans?
View 1 Replies View RelatedI would like to as you that i have swiches 2960 (10Unit) and switches 3560 ( 3 unit) and router 2821 ( 1 unite) and AP( 10 unit).So do you know software can manage all those product? Like monitor switch up or down, manage configure, check performance.
View 3 Replies View RelatedIs it possible to run VTP V3 on 2950 and 2960 switches. If so what version of IOS supports V3? Our 2960s are running 12.2(25r)SEE1, and 2950s are running 12.1(22)EA4a. Neither of which supports v3.
View 3 Replies View RelatedIs it possible to have ether-channel across 2 switches? As an example, having a server with 2 ports connect, 1 port to Switch-A and the other to Switch-B and then use those two links on the sepatate switches but to the same server to form an Etherchannel.
The Switch-A and Switch-B are 3560 series
I have to setup my first flex stack and wanted to make sure I do it right. I have the physical aspect of the stack down. From what I gathered I have to setup the master switch as the highest priority and then provision the other two switches. But I have configs on the other two switches, do I have to delete them? And do I have to setup individual ips for the two slave switches, because from what I saw the master switch is the only one with an ip address? The master switch is a poe 2960S-48LPS and the two other switches are 2960G-48TD
View 5 Replies View RelatedWas building a small network in Cisco Packet Tracer and ran in to an issue. I have 4 routers running OSPF, and off one of the routers I have 5 3560 Multilayer switches. The router that the switches hang off of, I have a sub-interface with dot1q encapsulation, set for vlan 10 and an IP Address. 10.14.16.1/24. The switches have interface vlan 10 configures, and have IPs in the same subnet. From that router, I can ping/telnet to all the switches without issue. My problem arises when I try and reach those switches from any other router. OSPF is set to redistribute static and connected subnets.The routing table is populated correctly on all the routers. When I ping and trace the packet, it looks like it makes it all the way to the respective switch, but the packet never makes it back. I've played with the default route on the switches to no avail. Am I trying to implement this incorrectly, or am I just missing something?
View 4 Replies View Related