Cisco Switching/Routing :: Daisy Chain From 3560 To 2960-S Switch
Feb 6, 2012Is it possible to daisy chain from a 3560 to 2960-S switch using a SFP interconnect cable (daisy chain cable)
View 1 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Cannot Uplink - Daisy Chain 2960S Series Switch To 3750
Feb 5, 2012I have a new Cisco 2960 S series switch with a basic configuration that needs to be uplinked or daisy chained to a Cisco 3750 switch. I am not getting any connectivity to the network with either a straight through or crossover cable. the port remains in amber but a 'show interface' indicates that the interface is up. I can manage the switch with a PC patched into any port on the switch with a static IP address. Must be something very simple that I am missing. Outlined below is the configuration.
Refresh_SW1#sh ver
Cisco IOS Software, C2960S Software (C2960S-UNIVERSALK9-M), Version 12.2(55)SE3,
RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[Code].....
Cisco Switching/Routing :: 2960 / 3560 - How To Restart Switch Physically
Mar 12, 2013I know only one method to restart Cisco switch through Telent using command " RELOAD". How can we restart Cisco 2960/3560 switch phyically....can i use mode button to restart cisco switch ?
View 11 Replies View RelatedCisco Switching/Routing :: 3560 And 2960 - Update Switch IOS Version At Packet Tracer 5.3
Oct 9, 2012I am using Packet Tracer to simulate Cisco networking.As the existing IOS of the 3560 and 2960 switch are in older version which has no new feature in new IOS, how to upgarde the IOS of Cisco switch at Packet Tracer?
View 5 Replies View RelatedHow To Configure Daisy Chain On Routers
Jan 21, 2012How to configure daisy chain on 3 routers ?
View 1 Replies View RelatedHow To Daisy Chain 2 Linksys EA3500 Wireless Routers
Nov 26, 2012I need to extend my wireless N network to increase the wireless reception power to a VIZIO Smart HDTV. I currently have a Linksys WRT310N router that is just barley being seen by the TV, Sometimes yes and sometimes not.I have just ordered a Linksys EA3500 Smart Wi-Fi Router. I want to set the EA3500 as the 1st (primary) router and CAT6 cable connect the WRT310N 50 ft closer to the HDTV.
View 1 Replies View RelatedDaisy Chain 2 Pro-curve 1810g 8 Port Switches
Jan 8, 2012i am trying to daisy chain 2 pro-curve 1810g 8 port switches.i got the cable i need to connect them but i just want to know what kind of settings i have to change on the switches to have it run as best as it can.
View 17 Replies View RelatedDaisy Chain 3 Wifi Routers - How To Extra 4 Ports On To Second Stage Router
Jan 16, 2013I have got 3 wifi routers i want to daisy chain. Router 1 is main modem router, which is connected to 2 pcs and 2 wif routers (wired separately), both of these wifi routers have there own ip address and dchp turned off, so they work fine and broadcast wifi nicely. now what i want to do is connect another wifi router to one of these routers (not the main one) but what setting do i need? i tried to connect the 3rd wifi router with the same setting as per the other two ie diff ip and dchp off, but when i plugged it into the port of the second router it would not show as connected or get an internet connection. Its probably quite simple to sort out, but with me being a dimwit i am tering my air out. If i could not use a wifi router for this 3rd connection, is there any other way of putting an extra 4 ports on to my second stage router.
View 4 Replies View RelatedLinksys Wireless Router :: E1000 - Create Guest Network On Daisy Chain System
Apr 5, 2013I have sent up a wireless network in a large building using WAG120N Modem Router and four E1000 wireless routers set as access points. The E1000's have the DHCP switched off to enable roaming so the WAG120N takes care of all that.
View 1 Replies View RelatedRouters / Switches :: Daisy Chain 3 Switches And Not Have Ip Conflict?
Jan 31, 2011Is it possible to daisy chain 3 switches and not have ip conflict? I am running a public access network for a library. For certain library software I need for all workstations to see each other. I have 25 workstations in total and two separate management consoles. I have all workstations on two switches but one of the management consoles is on the third switch because when joined with the others it has an ip conflict. I need this console for the digital sender that is connected as well as to act as a server for go print software.
View 3 Replies View RelatedCisco Switching/Routing :: Connectivity Between 2960 And 3560?
Dec 13, 2011From the multiplexer 9 ethernet connections are terminating in Cisco 2960G 24 port swith and it is connected through fiber uplink to one Cisco 3560G 48 port switch in first floor, which is connected to server.
How I will configure the 3560G to make communicate with 2960G and bring all these 9 ethernet connections to server. All the 9 connections are from different IP. and server also have different IP.
Cisco Switching/Routing :: 2960 / 3560 - Upgrading IOS 12.0 To 15.0
Dec 28, 2012It seems my 2960s and 3560s switches have enough flash space and memory to support the 15.0 IOS should I be OK to jump to this from 12.2(35)?
View 10 Replies View RelatedCisco Switching/Routing :: High CPU Usage On 3560 And 2960?
May 15, 2012I'm having issue with one stubborn process that is consuming nearly all the CPU on all of my switches. I tried googling it, but had no luck. The process is "hulc nrgyz PD di"
View 4 Replies View RelatedCisco Switching/Routing :: IOS 15 For 2960 And 3560 / 3750 Platforms?
Jul 26, 2011Yesterday Cisco released IOS 15 code into the wild for the 2960 and 3560/3750 families but the link to the release notes is not working. Because I already have a whole bunch of 4500/Sup7's running IOS 15 I am thinking about taking the plunge with 30 3750-X's I have on order but want to review the release notes first. where they might be hiding?
View 4 Replies View RelatedCisco Switching/Routing :: RPS 600 Is It Support Catalyst 2960 And 3560
Sep 13, 2012I have CISCO RPS 600 (PWR-AC-RPS) is it support Catalyst 2960 and 3560 ? and which type of cable require since i have cable 22-18 pin and on my switch require 22-14 pin.
View 2 Replies View RelatedCisco Switching/Routing :: 3560 / 2960 - VLAN Translation
Aug 6, 2012When did this wonderful feature get introduced? Is it going to moved down to the 3560s/2960s type switches?
View 0 Replies View RelatedCisco Switching/Routing :: 2960 / 3560 - OID For Reload Via SNMP?
Jul 10, 2012I would like to test the possibility to reload devices via SNMP for new switches like 2960, 3560 and so on.I know that the command "snmp-server system-shutdown" has to be configured, then I need to send the set query to the device via SNMP.
I have found on the net the OID 1.3.6.1.4.1.9.2.9.9.0 but it belongs to an old MIB and doesn't seem to work with new switch models.
Cisco Switching/Routing :: Port / MAC Based DHCP For 2960 And 3560
Jan 3, 2012I want to implement port-based and MAC-based in these two switches: 2960 & 3560 (both of them have this IOS version: 12.2(55)SE1). And I haven't found a way to implement both of them at the same time. This is what I got:
ip dhcp use subscriber-id client-id
ip dhcp subscriber-id interface-name
ip dhcp excluded-address 192.168.0.0 192.168.0.2
ip dhcp excluded-address 192.168.0.251 192.168.0.255
[code]....
With this configuration I can use port-based, but not MAC based. If I remove the first two lines and change the last line for this one:
address 192.168.0.7 client-id 0112.ae1d.af58.60
Then, the computer with that MAC address got the correct IP, but then the port-based doesn't work. Also, I got this line in the interface what I want to use MAC-based:
ip dhcp server use subscriber-id client-id
Cisco Switching/Routing :: Catalyst 3560 / 2960 Web-user Management
Jun 7, 2011We have quite a few 3560 & 2960 on our edge network - what I have been looking at was to access switches via web-interface i.e. web-browser. Only problem with this is it always gives you access on privilige level 15 which is not ideal as not all who we decide to give access to these switches will be admin and allowed to configure these swicthes - In the 3560/2960 data-sheet states:
"Alternatively, a local username and password database can be configured on the switch itself. Fifteen levels of authorization on the switch console and two levels on the Web-based management interface provide the ability to give different levels of configuration capabilities to different administrators"
Where as there is no mention of how to configure these two levels of Web-based management in the configuration guide.
Cisco Switching/Routing :: 3560 / 2960 - How To Configure 2 Ports To Provide Redundancy
Jan 21, 2013As per the attached diagram: How do I configure the 2 ports on the 3560 (Ports 6 & 7) and the connected ports on each of the 2960 switches (Port 25) to provide redundancy.
If the up link from Switch A dies then I need the traffic to flow through the trunk and utilize the up link on Switch B with minimal delay (milliseconds).
Cisco Switching/Routing :: 3560 / 2960 - Potential Spanning Tree Method
Oct 16, 2011 I have a Cisco 3560 running as a Level3 device in my network running 10 V LANs and routing between most of them (nothing complex with ACLs) and running spanning-tree mode pvst. The main network is run on a net gear GS748TPS stack of three switches running MSTP.
I have just bought an additional 3560 and a 2960 to plug in. I have set them up with IP addresses and then plugged them into the net gear. This brought the whole network down until I unplugged the new switches.
I have confirmed the IP addresses aren't duplicated and that DHCP is not running on the switches so I can only assume it's something to do with DHCP. I cannot afford for the network to go offline again, so is there anything I should check? Am I running incompatible spanning tree methods between the net gear and Cisco devices?
Cisco WAN :: Connect 2960-S To 3560 Catalyst Switch?
Feb 22, 2012Im trying to Connect a 2960-S Catalyst Switch to a 3560 Catalyst Switch. It worth pointing out im newish to switching although i know some commands and what they do This is my first time connecting 2 switches together.They are connected via a crossover cable and have green lights flashing on the connected ports When i run "show CDP neighbours it sees the new switch Unable to ping new switch...just timesout Here is the the interface on the 3650
GigabitEthernet0/40 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 001b.532f.8428 (bia 001b.532f.8428)
Description: Uplink to Switch 2
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
[code]....
Cisco WAN :: Cat 3560-E / 2960-G - Configuring Two VLANs On Same Switch Port
Mar 29, 2012As per my attached diagram, I have three switches (Cat 3560-E and couple of Cat 2960-G)
Each PC is on different vlan
PC -1 on vlan 100
PC-2 on vlan 200
I need to connect PC-1 and PC-2 to the server. Server has no fixed vlan and can be changed.
Restrictions:
1) can’t change PCs vlan assignment.
2) can’t add 2nd NIC in the server.
I’ve tried private vlan but it requires separate physical ports for host and/or community vlan and somehow it did not work. I could be wrong Trunking using dot1q enabled on port 2 on all switches and connection works fine (server to PC-1 or server to PC-2) by enabling switchport access vlan 100 or switchport access vlan 200. However I need port 5 on switch-1 to respond to vlan 100 and 200.
Cisco Switching/Routing :: 3560 Switch With LAN QoS
Jun 5, 2012I have issue with 3560 switch QoS configuration . I checked in cisco site about mentioned model QoS configuration.once we mark the frame and map the CoS to DSCP and once it enters into switch and it processes according to LAN QoS configured on interface
we have configured both the commands shape and share.
once it leaves the switch and enters into Edge router and if we do not have configured QoS in router which is normally MQC , how does it process each packet ?Do we need to have end to end QoS configured in LAN ?
Cisco Switching/Routing :: Cat 3560 No Switchport Command Test Out Routing With Switch
Dec 8, 2011The last few days I've been exploring options in getting rid of some old routers accross a wan connections. I have a cat 3560 to play with and I thought I would try and use the no switchport command test out routing with switch. I've got some type of route issue and I tried a few things which I thought would fix the issue but had no effect. I'll post the config and a few commands so you can see what the basic setup is.
Here we can see in the arp that it knows about both 10.7.1.2 (PC unable to ping 10.3.3.254) as well as 10.3.3.254 (ASA).I tried adding in a ip route of 10.7.0.0 255.255.0.0 10.3.3.110 as well as 10.3.3.254. Neither produced the results I wanted allowing 10.7.1.2 (PC) to ping the ASA (10.3.3.254). [code]
Cisco Switching/Routing :: 3560 VLAN Routing Between Switch And Router
May 8, 2012I have an environment of 3 X 3560G of which I have 1st switch-CORE(f0/10) connecting to the VPN router(CE) interface-f0/0. Remaining 2 Cisco 3560's(Access) are connected to Gi0/1 and Gi0/2 on the 1st switch-CORE via gi0/1 . On all three switches I have created multiple VLANs and assigned ports to these VLAN. The switch to switch connection is trunk allowing all VLANs created on all these 3 switches. Now the issue is how I am going to have all these VLANs routed through single interface on the routeri-e f0/0, as all these subnets will communicating to remote site over VPN. What should be default gateway on the 2 Access switches and the CORE switch, also what static route should be on router to reach all subnets(VLANs) created on these 3 switches.
I have read inter-VLAN routing i-e creating sub interfaces on router but dont want to proceed with that and looking for any other way to have my VLANs talk on all three switches and then are accessible to remote site ove VPN?
Cisco Switching/Routing :: Routing Secondary Network On 3560 Switch
Jun 4, 2013I am trying to get my workstation to talk to a workstation on a different sub-net through a Cisco 3560 switch. The switch is running the following IOS version: [code]
My primary network is 172.16.0.0 and I am trying to connect to a device on a 192.168.111.0 sub-net. [code]
What would be the best way to get the two workstations talking via the switch?
Cisco Switching/Routing :: How To Take Event Log Of Switch 3560
Feb 26, 2012how to take the event log of Cisco switch 3560, its argent.
View 1 Replies View RelatedCisco Switching/Routing :: Implement QOS On 3560 Switch?
Nov 22, 2011I have a 3560-48 switch running Cisco IOS Software, C3560 Software (C3560-ADVIPSERVICESK9-M), Version 12.2(44)SE3 and i need to implement basic QOS commands to the fast Ethernet interfaces as well as the gig interfaces and Also I need to create port channels on the switch and need what the port channel syntax are as well for that particular IOS version?
I have only read only access and i can't see what the QOS and Port channels syntax should be for that IOS version.
Cisco Switching/Routing :: QOS Config On 3560 Switch
Jul 22, 2012I'm in the process of configuring QOS on a 3560 routing switch in a GOLD, SILVER, BRONZE priority type scenario.
Firstly, I understand that this config will add a tag of "precedence 5" to a packet if it matches the "ACL_QOS_GOLD_In" access list. Question is does the router see this "precedence 5" tag and then sets the priority, or am I missing something in my config where at present it just sees the "precedence 5" and doesn’t act on it ?
Secondly, Since the "precedence 5" tag has already been added to the packets, do downstream routers see this tag and act accordingly or so I need to configure those is well ? [code]
Cisco Switching/Routing :: Configure QoS On 3560 Switch?
Jun 7, 2012configure QoS on 3560 switch i have taken the template from cisco configuration guide since we have different QoS configuration on each model.
below is the configuration :
configure terminal
mls qos
end
mls qos map cos-dscp 0 8 16 26 32 46 48 56
no mls qos srr-queue input cos-map mls qos srr-queue input cos-map queue 1 threshold 2 1 mls qos srr-queue input cos-map queue 1 threshold 3 0
[code]....
Currently all the cisco phones are connected to this switch and configuration with only one vlan that is voice vlan .
1) what is the outcome of this configuration , i mean, what will be the expected output ? end of the day we need to prioritize the voice traffic but why other commands including threshold and buffers are mentioned with respectives queues , if I need to explain that what am i expecting out of this configuration ?
2) this is LAN QoS which i understood but again , do i need to configure policy-map along with class-map which is MQC on this switch ?
3) i have edge router where i have MQC already configured but confusion with this switch which is working as a Access switch .
4) I referred the cisco QoS document for the respetive model whereas we have policy-map configured on the same switch with class-map .
My understanding is if we have configured the LAN QoS , and mapped the CoS value with DSCP , we need not to have MQC.
Cisco Switching/Routing :: 3560 - IOS On Switch Model?
Nov 9, 2011I am configuring some quotes for a customer whom I will be building a wireless network for. The wireless network will support about 60 AP's, as well as some other wired drops. The customer is working with a wireless vendor for the AP's, but I will be able to sell the switches for the network.
I want to ensure that he is pushing Gig and POE on each copper port for the AP's, since they will be "N" capable. I have selected several 3560 models which are in 24 port models, and I also think i have a requirement which mandates a 48 port in another location. What I have not been able to find in the Enterprise switch line is an 8 port which supports IOS and POE.
That being said, and since I am also "Select" certified, I went out to the SMB site, and did find that there were two models in the Small Business 300 line (models SG300-10P and SG300-10MP) which seem to support Gig ports as well as POE. I looked over the specs for each one of the two respective models, and I was not able to find what the difference between each of these two are. In other words, the specs, line by line, were identical.
Cisco Switching/Routing :: QOS For 3560 Access Switch
Nov 28, 2011we have a class based qos scheme (see attached file) on our 4500 series access switches and we have a access 3560-48 switch runing IOS Version 12.2(44)SE3 my question is can I use the same QOS scheme for the 3560 switch?
View 3 Replies View Related