Cisco Switching/Routing :: Implement QOS On 3560 Switch?
Nov 22, 2011
I have a 3560-48 switch running Cisco IOS Software, C3560 Software (C3560-ADVIPSERVICESK9-M), Version 12.2(44)SE3 and i need to implement basic QOS commands to the fast Ethernet interfaces as well as the gig interfaces and Also I need to create port channels on the switch and need what the port channel syntax are as well for that particular IOS version?
I have only read only access and i can't see what the QOS and Port channels syntax should be for that IOS version.
View 3 Replies
ADVERTISEMENT
Oct 12, 2011
I have attempted to implement DHCP snooping and have been having some strange issues. I have 5 3560s taht I use for my edge and when I attempt to implement on all five, the VLAN that houses my voice data appears to no longer be able to recieve DHCP lease renewals so after the 24 expiration all of my phones lose their configs. Once I roll back the changes the voice VLAN comes back. The other VLANs seem to function correctly as theya re able to renew their DHCP addresses.
The 3560s tie into each other using GIG Ports 1 & 2 and the top and bottom switches tie into our core switch, a 4507. The config that I use is below, failry simple and straightforward.
4 of the 5 switches feed our general office vlans for voice and data however the 5th switch is there for expansion and not in use. As such I have left the config changes in place on it and have tied myself and a colleague into it and have been operating fine for over a week now. So the config that I use seems sound in theory and should work on the other 4 switches with no issue.
View 14 Replies
View Related
May 1, 2013
Our enviornment includes 3560 switches and 2800 routers. We have a few remote offices using an application on TCP port 1677 that use far to much bandwidth. Our WAN provider can throttle and police this for us, if I can TAG this traffic, for example all Traffic from Florida using the Groupwise app on TCP uses TCP port 1677 and I want it tagged with CoS 3.
View 1 Replies
View Related
Jan 2, 2012
I need to implement the shaping VLAN only on the trunk link between the 6500 and 3560. [code]
View 8 Replies
View Related
Feb 26, 2013
I'm in the process of upgrading my 4507R core to a new 4507R-E. The old switch has Sup IV engines (WS-X4515) running IOS 12.2(40)SG and the new switch has Sup 6L-E engines running 15.1(2)SG. I'm trying to "move" my configuration from the old switch to the new. Below shows the commands configured in the old switch. I'm trying to determine how to implement the same configuration on the new switch since these commands are no longer available.
View 2 Replies
View Related
Jun 5, 2012
I have issue with 3560 switch QoS configuration . I checked in cisco site about mentioned model QoS configuration.once we mark the frame and map the CoS to DSCP and once it enters into switch and it processes according to LAN QoS configured on interface
we have configured both the commands shape and share.
once it leaves the switch and enters into Edge router and if we do not have configured QoS in router which is normally MQC , how does it process each packet ?Do we need to have end to end QoS configured in LAN ?
View 5 Replies
View Related
Dec 8, 2011
The last few days I've been exploring options in getting rid of some old routers accross a wan connections. I have a cat 3560 to play with and I thought I would try and use the no switchport command test out routing with switch. I've got some type of route issue and I tried a few things which I thought would fix the issue but had no effect. I'll post the config and a few commands so you can see what the basic setup is.
Here we can see in the arp that it knows about both 10.7.1.2 (PC unable to ping 10.3.3.254) as well as 10.3.3.254 (ASA).I tried adding in a ip route of 10.7.0.0 255.255.0.0 10.3.3.110 as well as 10.3.3.254. Neither produced the results I wanted allowing 10.7.1.2 (PC) to ping the ASA (10.3.3.254). [code]
View 4 Replies
View Related
May 8, 2012
I have an environment of 3 X 3560G of which I have 1st switch-CORE(f0/10) connecting to the VPN router(CE) interface-f0/0. Remaining 2 Cisco 3560's(Access) are connected to Gi0/1 and Gi0/2 on the 1st switch-CORE via gi0/1 . On all three switches I have created multiple VLANs and assigned ports to these VLAN. The switch to switch connection is trunk allowing all VLANs created on all these 3 switches. Now the issue is how I am going to have all these VLANs routed through single interface on the routeri-e f0/0, as all these subnets will communicating to remote site over VPN. What should be default gateway on the 2 Access switches and the CORE switch, also what static route should be on router to reach all subnets(VLANs) created on these 3 switches.
I have read inter-VLAN routing i-e creating sub interfaces on router but dont want to proceed with that and looking for any other way to have my VLANs talk on all three switches and then are accessible to remote site ove VPN?
View 9 Replies
View Related
Jun 4, 2013
I am trying to get my workstation to talk to a workstation on a different sub-net through a Cisco 3560 switch. The switch is running the following IOS version: [code]
My primary network is 172.16.0.0 and I am trying to connect to a device on a 192.168.111.0 sub-net. [code]
What would be the best way to get the two workstations talking via the switch?
View 3 Replies
View Related
Feb 26, 2012
how to take the event log of Cisco switch 3560, its argent.
View 1 Replies
View Related
Jul 22, 2012
I'm in the process of configuring QOS on a 3560 routing switch in a GOLD, SILVER, BRONZE priority type scenario.
Firstly, I understand that this config will add a tag of "precedence 5" to a packet if it matches the "ACL_QOS_GOLD_In" access list. Question is does the router see this "precedence 5" tag and then sets the priority, or am I missing something in my config where at present it just sees the "precedence 5" and doesn’t act on it ?
Secondly, Since the "precedence 5" tag has already been added to the packets, do downstream routers see this tag and act accordingly or so I need to configure those is well ? [code]
View 2 Replies
View Related
Jun 7, 2012
configure QoS on 3560 switch i have taken the template from cisco configuration guide since we have different QoS configuration on each model.
below is the configuration :
configure terminal
mls qos
end
mls qos map cos-dscp 0 8 16 26 32 46 48 56
no mls qos srr-queue input cos-map mls qos srr-queue input cos-map queue 1 threshold 2 1 mls qos srr-queue input cos-map queue 1 threshold 3 0
[code]....
Currently all the cisco phones are connected to this switch and configuration with only one vlan that is voice vlan .
1) what is the outcome of this configuration , i mean, what will be the expected output ? end of the day we need to prioritize the voice traffic but why other commands including threshold and buffers are mentioned with respectives queues , if I need to explain that what am i expecting out of this configuration ?
2) this is LAN QoS which i understood but again , do i need to configure policy-map along with class-map which is MQC on this switch ?
3) i have edge router where i have MQC already configured but confusion with this switch which is working as a Access switch .
4) I referred the cisco QoS document for the respetive model whereas we have policy-map configured on the same switch with class-map .
My understanding is if we have configured the LAN QoS , and mapped the CoS value with DSCP , we need not to have MQC.
View 4 Replies
View Related
Nov 9, 2011
I am configuring some quotes for a customer whom I will be building a wireless network for. The wireless network will support about 60 AP's, as well as some other wired drops. The customer is working with a wireless vendor for the AP's, but I will be able to sell the switches for the network.
I want to ensure that he is pushing Gig and POE on each copper port for the AP's, since they will be "N" capable. I have selected several 3560 models which are in 24 port models, and I also think i have a requirement which mandates a 48 port in another location. What I have not been able to find in the Enterprise switch line is an 8 port which supports IOS and POE.
That being said, and since I am also "Select" certified, I went out to the SMB site, and did find that there were two models in the Small Business 300 line (models SG300-10P and SG300-10MP) which seem to support Gig ports as well as POE. I looked over the specs for each one of the two respective models, and I was not able to find what the difference between each of these two are. In other words, the specs, line by line, were identical.
View 6 Replies
View Related
Nov 28, 2011
we have a class based qos scheme (see attached file) on our 4500 series access switches and we have a access 3560-48 switch runing IOS Version 12.2(44)SE3 my question is can I use the same QOS scheme for the 3560 switch?
View 3 Replies
View Related
Mar 18, 2013
I have a 3560 switch with 1 VLAN (VLAN 10) where I need to make ports:
1-10 as isolated (can't contact each other)
11-20 as community (need to contact each other like a normal VLAN)
23 as promiscuous (server that ports 1-20 need to get to)
24 as promiscuous (WAN router where ports 1-20 need to get to and the remote servers).
[Code]...
View 26 Replies
View Related
Oct 31, 2012
I wanted to upload image having .tar extension in Cisco 3560 switch. What are the steps to upload.
View 1 Replies
View Related
Feb 12, 2013
I have observed a situation where one of our cisco switch 3560 is rebooting daily at periodic times.We have checked the power cables and source everything is fine and still clueless whats causing the issue. [code]
View 13 Replies
View Related
Aug 19, 2012
I want to configure Cisco 3560 SWITCH with IP cameras. I need to configure the ports connected to Camers. IP addresses to the Cameras has been assigned.
View 1 Replies
View Related
Sep 26, 2011
I have an issue with a 3560 in my network, after sometimes it fails to give out power to some ip phones,while others are not affected and below is the message i get
"Power given, but Power Controller does not report Power Good"
output of sh power inline and sh env all : everything seems to be ok on the switch
#sh power inline
Available:450.0(w) Used:48.0(w) Remaining:402.0(w)
Interface Admin Oper Power Device Class Max
(Watts)
--------- ------ ---------- ------- ------------------- ----- ----
Gi0/1 auto off 0.0 n/a n/a 15.4
Gi0/2 auto off 0.0 n/a n/a 15.4
Gi0/3 auto off 0.0 n/a n/a 15.4
[code].....
It's solved by a reboot of the switch, i could have suspected a power environnment issue but it's the only equipement disturbing in the network.
View 20 Replies
View Related
Feb 7, 2012
Are the LC SFPs interchangeable with the 3560 V2 POE switchThe P/N number we have on the LC SFPs are 30-1301-04.Will this P/N number suit bothe the 2960-S and 3560 switches
View 1 Replies
View Related
Aug 20, 2012
I am trying to configure 802.1x wired on a 3560 switch and don't see the required commands under the interface. I am running c3560-ipbasek9-mz.122-55.SE6.bin. I was thinking it might not be available on the ipbase image, but I do have the commands on a 3750g running the ipbase image, so I'm not sure about that.
View 4 Replies
View Related
Sep 10, 2012
i am facing an error while upgrading the IOS image on 3560 switch. [code]
View 1 Replies
View Related
May 25, 2012
I have made a topology by using one 3560 switch and 2 2950 switches. I have also made 2 vlans name Clients and other Servers and vlan 1 is for anagement purposes. The left 2950 switch is for clients and the right is for servers. Clients is vlan 2 and servers is vlan3 . Now what i want is that my dhcp is should assign ips to clients in vlans 2 provided that servers are in vlan 3. I am also using a border router and i have introduced a default route on the 3560 to the border router.
Now when i assign static ips to my clients pc and server dhcp then i can ping between vlans but when i try to assign ip through dhcp then it wont work. Also the default route on the switch to the border router doesnt seem to work. I can ping only the border router when i put a default route on the border router instead of the 3560 switch.
View 3 Replies
View Related
Jul 23, 2012
I have a cisco 3560 24PS and its connected to two ADSL broard band routers.one is a personal broadband line using a Billion ADSL broadband router, and the other is a business broardband line using BT's 2wire broadband line.on the Billion routers i have various things attached like a NAS and a printers, both wired connections. then i have laptops and phones that connect over wifi, so its configured to act as a DHCP server
the only thing conncted to my 2wire router is my company's laptop (wired or wifi depending on where i'm working from), so again i have it working as a dhcp server.The switch is configured with multiple vlans, with dhcp scopes assigned for each vlan.I have a static route pointing all traffic to my Billion ADSL for internet connectivity.
The problem i'm having is that when i turn on the cisco switch, all wifi conected devices loose their conection. only 2 things get it working again, a reboot of the router, or disabling then enabling the DHCP service on the router.upon further analysis i was able to find out that the devices were not able to pick up an address from the router. again i looked deeper into this and i can see the following on logs of my router: [code]
so it seems that the router tuns off its DHCP capabilities because it detects that my Cisco switch is running DHCP services. I need to figure out how to keep the billion routers DHCP running when ever the switch is turned on.is there a way of filtering out any DHCP chat from the switch to the router?
View 7 Replies
View Related
Apr 17, 2013
I want to replace an existing 3560 Switch with another switch of the same exact model and IOS. However, this switch that needs to be replaced is the VTP Server of my LAN at this location. When I replace the switch I will just use the same exact running config but I'm concerned about the vlan.dat file. Do I need to copy that file over to the new replacement switch and if so, what is the best way to do that?
View 5 Replies
View Related
Sep 12, 2010
I have the following problem with
Situation:
- 2x 3750G-12S Distribution-Switches (DS) and several 3560/2960 Access-Switches (AS)
- redundant Fiber optic uplinks between AS and DS
- Cross-Stack Etherchannel config on all uplinks
- UDLD aggressive mode configured on all uplinks
Problem:
- when I reload the DS and the switch comes up again, I've lost the connection with several (not all) AS
- looking at the AS log I found the following error message: "%UDLD-4-UDLD_PORT_DISABLED: UDLD disabled interface Gi0/1, aggressive mode failure detected"
Cause:
- in the log of the AS I don't see intf Gi0/1 go down during the reload of the DS
- this means the DS didn't shuts down all its ports during the reload
- but this also means that UDLD on AS didn't know about DS reload, and therefore didn't resets counters
Workaroud/Solution
- I'm now configuring errdisable recovery on all AS
So I'm forced to configure errdisable recovery, even if I don't want.
View 3 Replies
View Related
Apr 6, 2013
does cisco switch 3560 or 3750 supports MC-LAg ? if yes, then on what IOS? if no, then what are the devices which supports MC-lag?
View 1 Replies
View Related
Oct 30, 2011
I have configured a new switch 3560 switch and connected to 4500 switch and formed a trunk connectivity.Now the issue i am facing is when i do a SH CDP NEIGHBOUR from 3560 switch i am able so see 4500 swries switch but at the same time when i do SH CDP NEIGHBOUR form 4500 series switch i am not able to see the entry for 3560 switch.But i am able to telnet the new switch with out any issues
View 11 Replies
View Related
Sep 25, 2012
I have a 3560-X switch and want to access it through GUI. what image I need to download and steps to use GUI(Just like ASDM for ASA 5500 series Firewall).
View 1 Replies
View Related
Jan 2, 2013
My access switches LED is start blinking very fast suddenly,it has single up link from the Core switch.access switch is 3560.what can be the possible problem.
View 1 Replies
View Related
Mar 9, 2012
I have upgraded my C3560-PS-S switch to the latest IOS version 12(2)55-SE4 and it is not providing PoE anymore? It used to work before this upgrade? I searched Cisco bugtrack and there is bug defined for this IOS/Switch.
Switch(config-if)#do show power inline Available:370.0(w) Used:0.0(w) Remaining:370.0(w)
Interface Admin Oper Power Device Class Max
(Watts)
--------- ------ ---------- ------- ------------------- ----- ----
Fa0/1 auto off 0.0 n/a n/a 15.4
Fa0/2 auto off 0.0 n/a n/a 15.4
Fa0/3 auto off 0.0 n/a n/a 15.4
Fa0/4 auto off 0.0 n/a n/a 15.4
Fa0/5 auto off 0.0 n/a n/a 15.4
Fa0/6 auto off 0.0 n/a n/a 15.4
Fa0/7 auto off 0.0 n/a n/a 15.4
Fa0/8 auto off 0.0 n/a n/a 15.4
Fa0/9 auto off 0.0 n/a n/a 15.4
Fa0/10 auto off 0.0 n/a n/a 15.4
Fa0/11 auto off 0.0 n/a n/a 15.4
Fa0/12 auto off 0.0 n/a n/a 15.4
Fa0/13 auto off 0.0 n/a n/a 15.4
Fa0/14 auto off 0.0 n/a n/a 15.4
Fa0/15 auto off 0.0 n/a n/a 15.4
Fa0/16 auto off 0.0 n/a n/a 15.4
Fa0/17 auto off 0.0 n/a n/a 15.4
Fa0/18 auto off 0.0 n/a n/a 15.4
Fa0/19 auto off 0.0 n/a n/a 15.4
Fa0/20 auto off 0.0 n/a n/a 15.4
Fa0/21 auto off 0.0 n/a n/a 15.4
Fa0/22 auto off 0.0 n/a n/a 15.4
Fa0/23 auto off 0.0 n/a n/a 15.4
Fa0/24 auto off 0.0 n/a n/a 15.4
View 3 Replies
View Related
Mar 12, 2013
I know only one method to restart Cisco switch through Telent using command " RELOAD". How can we restart Cisco 2960/3560 switch phyically....can i use mode button to restart cisco switch ?
View 11 Replies
View Related
Nov 29, 2012
RACK 1 is the old rack and NEW RACK is the rack which is going to be procurred for some new Servers. All the Servers in the RACK 1 has a default gateway as PIX Inside IP. As of now the 3560 Switches acts as Layer 2 and does not have L3 IP routing enabled. How can I enable conenctivity between 192.168.36.0 range and 192.168.57.0 range wihtout making any change to current PIX inside IP address 192.168.57.1?Is it possible that I can enable IP routing on the 3560 Switches , create interface VLAN 36 and since already Switch 2 has it 's default gateway as 192.168.57.1 , Would the traffic from 192.168.36.0 be routed to 192.168.57.1 ? Or do I need to create static route for that ?Since L3 Routing is not enabled and since the 3560 Switches are just acting as L2 , the VLAN 2 - 192.168.57.0 range does not have any interface VLAN configured. When it is changed I would need to create interface VLAN 2 on 3560 Switches?
View 18 Replies
View Related
