I recently acquired a used SRW2016 in perfect working order (I checked it) and then made the mistake of trying to update the software image. Since then I cannot get any image to boot and cannot install a new one despite many attempts with XMODEM.The switch is hardware version 1.1 with Boot image "BOOT Software Version 1.0.0.03 Built 08-Jun-2004 09:48:10" I've tried installing a new boot image via XMODEM: [code]
View 4 RepliesI have tried to update the firmware of my srw2016 but after this update my switch wouldn't start again.
It shows this message in my console:
Exit from boot menu. Continue with flow.
Preparing to decompress...
Image in address: 0x0 - Check Sum error!
Please download a new image.
Downloading code using XMODEM.
I have had the switch for about 2 years and recently moved. The manual specifies:
38400 bps and 8-n-1 serial port settings using DB9F to DB9F cable.
I have done this and tried using multiple machines/ports/cables as well as several peices of software (minicom, PuTTy, hyperterminal) and none give me any output from the switch at all.
The trouble is that in its original config, it had 1 port locked into its own VLAN for management with port security and an obscure RFC1918 IP address which I cannot recall for the life of me.
At this point, I have no access to TCP/IP management so serial console is my last hope and is not working.
Im trying to recover the password from my stacked switchs(doing procedure on master switch),im following a guide i have read in this forum("SRW248G4 V1.1 unable to reset password"), at console terminal have chosen "password Recovery" it prompts the "current password will be ignored" and then i hit "Escape" the switch start loading de configuration, at this point i attempt to login from telnet or http but the login fails.
Here is the password/username combo im using (admin/blank ; admin/admin). Is it possible to restore admin password or should i just hardware reset the switchs?
I did RECOVERY on my computer. Its a Compac Windows XP Home edition. This computer runs off of my main computer by a router & adapter. My router & adaptor are showing green but the Internet is showing red. Its becuz my high speed Internat service is ATT.my.yahoo.com. which comes through IE. On my newer computer all is fine. My IE works good & all is working. but my IE on my older one which runs with the router wont set up.
View 1 Replies View Relatedi need to recover a router Cisco 2801. I lost the password and the "no service password-recovery" is configured. I have done many attempts with the procedure in this link :URL
View 9 Replies View RelatedI was messing with the settings, it saved now I can't access it because I can't find the ip...
Current Setup:
When I remove the router and connect directly to the switch, I lose connectivity all together.
What can I do? I don't own a console wire.
I'm Upgrading from a SG-300-10 to a SG-300-28P - Can I just load in the Config from the SG300-10 into the SG-300-28?
View 2 Replies View RelatedRecently I brought SG 300-28.It came loaded with firmware ver 1.0.0.27.Can I upgrade it to ver 1.1.2.0 directly?
View 2 Replies View RelatedWe have 2x Cisco 3750 WS-C3750-48PS-S and 1x WS-C3750-48PS-E in stack mode. They all work well. Currently they have c3750- ipservicesk9-mz.122- 25.SEE2.bin on them which is deffered by Cisco. What would be a good alternate, stable version for my switches? Switches have 16MB flash and 128mb Ram.
View 4 Replies View RelatedJust updated the fw to 1.2.5.70 and after a while, the device crashed wth the following message in the flash log.
21474836472012-Jun-17 11:46:21Emergency %SYSLOG-F-OSFATAL: FATAL ERROR: GOAH: ABORT DATA exception ***** FATAL ERROR ***** SW Version : 1.2.5.70 Version Date: 11-Jun-2012 Version Tim e: 17:35:31 Instruction 0x150348 Exception vector 0x10 Program state register 0x60000013 0x0015014c ***** END OF FATAL ERROR ***** Haven't seen the switch crashing before.
We have Sg-300-28 serious switches(SRW-2024 k9-EU) and i want to upgrade switch with latest firmware, any info for latest firmware is used for the same ?
View 6 Replies View RelatedI'm trying to upgrade a switch SRW224G4 but without success. Model Name SRW224G4 Hardware Version 00.03.00Boot Version 1.0.0.06
I send the file via the XModem( SRW2xxG4_FW_1.2.3.0 ).
I have just attempted to load the latest firmware on an SLM2008, everything appeared to work as expected BUT, the switch is no longer pingable on its static IP doesn't appear to have attempted get an address via DHCP. I have attempted power cycling the switch but it has made no difference. The switch is still switching but I have no management any more. What to do next ?
View 1 Replies View RelatedI have upgraded my 7 x SG200 50/50 switches from 1.1.2.0 to 1.2.5.70 and after upgrading,most of these switches rebooted by itself while I'm saving or logging off. It gives me this error
View 7 Replies View RelatedI have 2 6509 switches configured with VSS.As per advised my managment I have to enable SSH but it is not available existing IOS which is "s72033-ipbase-z.122-33.SXI3.bin". SSH available in "s72033-ipbasek9-mz.122-33.SXI10".
upgrade the IOS with VSS configured switches.
I've been having a problem with a brand new SG300-10 switch that I posted about yesterday. I checked the firmware and it was at 1.0.0.27 and the lastest is 1.1.0.73. So I backed up the current firmware and loaded the 1.1.0.73 version and it seem to be CLI based only, with no web GUI.
If so is there an easy way to reload the 1.0.0.27 using the CLI? There is nothing in the CLI docs that I can see unless it's buried.
The release notes for 1.1.0.73 don't say it's CLI only either, maybe something just went wrong but the CLI seems to be functional.
After performing a firmware upgrade on an SG300-20 switch from ver 1.1.0.73 to 1.2.5.70 the switch now boots up with the following error and resets:
30-Aug-2011 10:47:33 %L1Mngr-F-PARAMTOOLONG: csco-sb parameter %s is too long.
The attached file contains a full output of the console boot process. I have tried loading different versions from the console, but all produce the same error.
I have just downloaded new software for sge2010p. I had tried to made an upgrade on some switches, but switches still boot with the old software.I have installed software 3.0.0.18 and boot 2.0.0.03. I have downloaded software 3.0.1 from cisco, put it on tftp and started an upgrade via switch web interface. I have checked that the active image is set to 1, and started the upgrade.Switch has downloaded soft from tftp, and reported that process has been finished without errors.After the restart switch have 3.0.0.18 software again. I have try to do this same on 4 different switches working in L3 and L2 mode - always with the same effect.Should I upgrade both images in the same time to get this work?
I have noticed, that the new firmware is located on image 2.
# show bootvar
Image Filename Version Date Status
----- --------- --------- --------------------- -----------
1 image-1 3.0.0.18 08-Nov-2009 16:21:37 Active
2 image-2 3.0.1.0 19-May-2011 13:05:53 Not active*
[Code] ...
So I try to set active image via console command:
# boot system image-2
and again...
a# show bootvar
Image Filename Version Date Status
----- --------- --------- --------------------- -----------
1 image-1 3.0.0.18 08-Nov-2009 16:21:37 Active*
2 image-2 3.0.1.0 19-May-2011 13:05:53 Not active
"*" designates that the image was selected for the next boot
Finally i have tried to set the active image to "2" using console menu: I have set it like this:
Active Image
============
Unit ID Active Image Active Image after Reset
======= ============ ========================
1 Image 1 Image 2
and save..
[Code]
Where is the right place to set active image for 2. Is the "active image" settings only sets the firmware image which switch uses or configuration files too?
Using the SGE 2010 for Microsoft NAP with 802.1x auth for switch access, which led to a few issues
What i have: An SGE 2010 48 port switch, firmware 3.0.0.17 Firmware upgrade: In order to ensure im not having problems due to old firmware, i tried to upgrade using ros_ls1_bp_ge_bx-3020.ros in order to move to 3.0.2, when uploading the file via TFTP, the upload completes and thats it, nothing happens.Restarting the device: As part of the upgrade process, i thought i might of had to reboot, so i rebooted, and found that all my settings were wiped clean, as if a factory reset had been performed.... and add further to pain, the backup of settings that i had taken do not seem to want to re-apply.NAP support: So i have tested my NPS (radius) server with NTRadping.exe and all is good, however i cannot get the SGE2010 to talk to it.... the authenticator state in the web interface is always listed as initialising.... im not sure if this is a simple incompatibility (hence the attempt at a firmware upgrade), a tag that needs to be set on the radius side or a switch misconfig.
1) how on earth do you upgrade the firmware?
2) why are none of my settings being saved when the device reboots ?
I am trying to do ios upgrade on 5 stacked 3750 switches. All the switches have different model number, so i am wondering which image file i should download. As far as i understand all the stacked switches should have the same IOS, i may be wrong. The switches have the following model numbers and SW images;
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
1 28 WS-C3750G-24PS 12.2(35)SE5 C3750-IPSERVICESK9-M
* 2 28 WS-C3750G-24PS 12.2(35)SE5 C3750-IPSERVICESK9-M
3 52 WS-C3750G-48PS 12.2(35)SE5 C3750-IPSERVICESK9-M
4 30 WS-C3750E-24PD 12.2(35)SE5 C3750E-UNIVERSAL-M
5 30 WS-C3750E-24PD 12.2(35)SE5 C3750E-UNIVERSAL-M
which image file i should use as they all have different model numbers and Cisco provides different image files for each model.
I have a switch SRW224G4 from Linksys and doesn't work now after an firmware upgrade!
Simple, here the result when I try to install the firmware "ls_106-12216.ros" or "SRW224G4P_SRW248G4P_image_v1020.bix" that came from your web site!
Here the result for "ls_106-12216.ros"
Calculating file's checksum...OK
Erasing FLASH ->>>>>>>>>>>>>>>>>>>>>>>>>>
[Code].....
with TFTP upgrade SRW2xxG4_FW_1.2.3.0.ros and WEB interface after the restart, the switch will not start, display HyperTerminal link. You can also restore the switches do not?
View 1 Replies View RelatedI HAD similair problem:[URL](Have ver 1.1) Forgot password. Restored to v1.0.0.86 via telnet Been playing around with telnet AND web based updates Read somewhere else (Web-based ONLY works with IE) (Tried Web-based and keep getting "Copy Failed/Undefined Error" and 0 Bytes transfered) Know to upgrade "Boot" first, then "Software Image" THEN reboot
Tried telnet (not through web-based startup) Can get to "lcli" (by Ctrl+Z twice)Retyped Username and Password:
At "console#" tried typing "copy tftp:///srw2024_16_boot-101.rfb boot" didn't work : "Must be valid URL or reserved keyword"
Where am I going wrong?
I have downloaded the ros file, but can't find how to apply it. I know this information must be out there, but can't find it.
View 2 Replies View RelatedMy task is to upgrade a couple of 6500 series switches, 6513 with SUP720/MSFC3 (WS-SUP720) and Policy Feature Card 3 (WS-F6K-PFC3B) installed. How to upgrade those switches if in SSO redundancy mode with two SUPs installed?
I understand that it is good to connect to the MSFC3 via console and upgrade this first, is this correct?
I also have to upgrade some 6509 but I only can test it on one 6509-E, how to get everything up to date. [code]
I am trying to update the SGE2000v1.0 with 24ports to 3.0.1.0: url...I got the error "illegal software format" using tftp.
View 2 Replies View RelatedI have a DI-604 D-link router, is it necessay to upgrade to newer router to get faster access to internet? Upgrade Firmware? I have a PD950 processor with Win XP pro and use it for DAYTRADING streaming data and fast executions.
View 5 Replies View RelatedWhere I can find ACS 5.X recovery DVD. I have vm ware and want to make .iso to recover lost system password.I am not able to find in any Cisco downloads.
View 2 Replies View Relatedwhere I can find a CLI password recovery procedure for the administrator account?
View 1 Replies View RelatedI have problem recovering my cisco 501 pix password. I followed instructions on this pageurl... but it seems its not working. I cant ping my TFTP Server on my pc. I tryed to disable firewall on my pc, i did a fresh install Windows but still i cant ping my TFTP Server on my PC.
View 8 Replies View RelatedAs I make a password recovery to a Cisco PIX 525 Version 6.3(3)?
View 1 Replies View RelatedIt's impossible to use acs 5.2 recovery DVD to cisco 1121 acs 5.1?
View 7 Replies View Related