Cisco Switches :: SGE2000P Stack Password Recovery?
Mar 22, 2013
Im trying to recover the password from my stacked switchs(doing procedure on master switch),im following a guide i have read in this forum("SRW248G4 V1.1 unable to reset password"), at console terminal have chosen "password Recovery" it prompts the "current password will be ignored" and then i hit "Escape" the switch start loading de configuration, at this point i attempt to login from telnet or http but the login fails.
Here is the password/username combo im using (admin/blank ; admin/admin). Is it possible to restore admin password or should i just hardware reset the switchs?
View 3 Replies
ADVERTISEMENT
Aug 3, 2011
I'm using a stack of four SGE2000P switches for a PoE video camera system. I've got the cameras in a VLAN and everything's working fine.
I'm wondering, though, is there a way to find out what data rate the stack interfaces are working at (since it's going over cable infrastructure we put in ourselves), and also what percentage of that bandwidth is being used? I don't see anyway to get to those interfaces from the main page, and I wasn't able to find a way to do any sort of percentage thing even on a regular interface.
View 2 Replies
View Related
Feb 3, 2013
I need to recover the passwords for my 3750 stack (2 switches), I have the password recovery documentation but it seems to be referring to recovery for one switch. How do I go about recovery when in a stack, should I remove the links on the switches and recover each one separately?Alternatively can I do a factory reset on them
View 1 Replies
View Related
May 1, 2012
i need to recover a router Cisco 2801. I lost the password and the "no service password-recovery" is configured. I have done many attempts with the procedure in this link :URL
View 9 Replies
View Related
Dec 27, 2012
I am trying to get QoS for my VoIP system setup on several SGE2000p switches and have got a question...How do I define the ACL for RTP? As far as I can tell it will not let me enter a UDP port range for the RTP traffic... And I cant imagine creating rules for each port would be very effective either. So, how can I define an ACL to cover the RTP traffic so I can classify it?
View 4 Replies
View Related
May 29, 2012
We have a potential new customer who is wanting to deploy a guest WLAN. I am happy doing this via a VLAN on the WAP4410N series AP’s. I would then create the relevant VLAN’s on the switch. Can each VLAN be assigned an IP address and allowing me to be able to add a static route on the router pointing the traffic for the Guest VLAN back to the switch?
View 1 Replies
View Related
Sep 19, 2011
I've got multiple SGE2000P & SGE2010P switches
Originally I was happy just set them all up in a stacked ring configuration. However I've become aware that my back bone fibre links are contantly pushed to their max.
So I've decided that I should change this configuration and unstack the switches and make them all stand-alone units. and I'll configure 2 cable LAG links between all my switches Theorically I should now get 2GIGs between each switch and to complete the ring in my network for redundancy I'll turn on Spanning tree.
However I've tested the speed and I just can not seem to get a LAG connection with 2 x 1gig cables to push more data than a single link 1gig link cable would.
My test enviroment(not using fibre optic cables just cat5e copper cabling):
4 x pc's(all gigabit network cards)
2 x sge2000p switches
PC1 ---(1G eth)--- /---(1G eth)--- PC2
[SGE2000P]===(LAG1 2x1G cables)===[SGE2000P]
PC3 ---(1G eth)---/ ---(1G eth)--- PC4
If I send files from PC1 & PC3 simultaneously to PC2 & PC4 They don't transfer faster than if I I just use a single 1GIG Link cable
looking at the LAG configuration it shows both cables are connected & the LAG looks like it's working. But it really doesn't seem to be running at the expected 2GIG?
The LAG fail over seems to work fine if I remove either of the 2 cables from the LAG the link continues to work. (sometimes it will drop a ping when removing or readding a LAG cable)
View 3 Replies
View Related
Sep 17, 2011
I'm planning to separate voice and data traffic with two vlans. I have a COR switch catalyst 3750, a UC560 for VOIP with SIP trunk and SGE2000P as access switches. The thing is i had configured VLAN1 (data vlan) and VLAN8 (voice vlan), i've created the vlan 8 in the database on 3750 and let pass those vlans through a TRUNK port. In the SGE2000P configuration i've created the VLAN8 and the the ports as trunk for letting pass the two vlans for the PC and the IP phone. This works but some phones aren't registering, and for example i've unplugged a register phone and plug and doesn't registering anymore.
View 0 Replies
View Related
Nov 1, 2011
We have one SGE2000P switch that we are testing in Layer 3. We have a very simple configuration with some vlans that we want to route to our corporate network, but I want to test if there is actually traffic coming out from the up-link port first.
1- Created the vlans:
VLAN1: 10.10.1.12 /16 (native)
VLAN10: 172.16.10.1 /24
[Code].....
View 1 Replies
View Related
Feb 15, 2012
I am having problem setting up SGE2000P switches to work with my default data VLAN and additional voice VLAN. I am configuring it to pick IP address for phones from voice VLAN which is working fine but when I connect a PC on phone port it is also picking up an IP from Voice VLAN while default VLAN is data with different scope of IP.
I pack these switches and purchase ESW 500 series. I have ESW 500 at another client and they are working fine out of the box but this guy is giving me hard time.
View 1 Replies
View Related
Mar 25, 2013
Currently, we have a plain network and we are planning to 'upgrade' it a little. We want to implement VLANs to separate wireless clients, workstations + servers and infrastructure devices form each other.As of now, we have no VLANs, and no managed Switches. We only have an RV016 that handles two ISPs and a 3rd party connection service to the office branches ( I belive they're using Frame Relay, but as far as we know, we are not concerned since we cannot touch their devices)
The reason behind the title, pointing towards the famous SGE2000P, is that my workplace is located in Argentina... and we don't have as many choices as some of you guys have ! In fact, I was unsuccessful trying to get a Cisco partner to contact me. We would like to replace the RV016 with a cisco 1941 (and a HWIC switch card).
So, back to business..! Assuming we will be using the SGE2000P switches, I was thinking about setting VLANs using 802.1Q through seven of these switches, along with a 1941 Cisco router. I'm expecting the 1941 to handle load balancing between both ISPs and the 3rd party link. Now, as for Inter VLAN routing, I would like to have gigabit traffic between VLANs.
Is it possible to use one SGE as Layer 3 mode to hande inter VLAN traffic (gigabit speeds) while using the 1941 as a end point device to reach internet (using PAT) ?Would you suggest me to use the 1941 for Inter VLAN routing, despite the 10/100 limitation(*) and use all SGE's in L2 mode? We need two ISPs, a third link for the FR connection, and finally the LAN interface. As far as I know, I'm limited to the gigabit builtin interfaces for WAN purposes, am I right?
View 5 Replies
View Related
Jun 4, 2013
I'm working with a customer who has an SGE2000P and a Catalyst 2960 to setup and configure a single mode fiber link. The SGE2000P has an MFELX1 fiber GBIC and the 2960 has a GLC-LH-SMD GBIC. When I have the customer plug in his fiber, there is a power light that comes on on the MFELX1 GBIC. Neither GBICs/switches show that a link or activity is occurring, but the presence of that light makes me think that they are connecting somehow. Are these two switches/GBICs compatible?
View 1 Replies
View Related
Oct 20, 2011
where I can find a CLI password recovery procedure for the administrator account?
View 1 Replies
View Related
Nov 18, 2011
I have problem recovering my cisco 501 pix password. I followed instructions on this pageurl... but it seems its not working. I cant ping my TFTP Server on my pc. I tryed to disable firewall on my pc, i did a fresh install Windows but still i cant ping my TFTP Server on my PC.
View 8 Replies
View Related
Dec 13, 2011
As I make a password recovery to a Cisco PIX 525 Version 6.3(3)?
View 1 Replies
View Related
Jun 1, 2011
I just bought one of these in and it was in production and I have no way of getting a hold of the login information. Is there a way to wipe these to factory defaults? I have been looking everywhere with no such luck.
View 2 Replies
View Related
May 6, 2011
I am a student pursuing a CCNA certification currently. I recently came across a lot of 3548 xl switches. They power up fine, post with out problem and load flash. The problem I am running into is that the console is password protected. I have found the password recovery procedure for this switch, but it requires the use of the mode button. I have tried this process several times and the flash file is loaded with the startup config file. How do I perform a password recovery on a switch with a broken mode button?
View 1 Replies
View Related
Apr 10, 2012
how to recover ACS 5.0.021 CLI password.I dont have 5.0.021 cd with me can i use 5.2 cd to recover the same ?
View 1 Replies
View Related
Mar 12, 2012
To configure my Cisco, I use the console cable but as I have no serial port on my PC, I use a USB to serial cable which I plug the console. I had lost this USB cable -> serial but I found another one. So I started to configure my Cisco by copying from an existing config. I found out that a prior the converter is defective and copy the wrong config.
I had copied the enable secret password and it badly copied! No luck, I made a copy run start. Therefore more accessible to Cisco! When I start the Cisco, I see what activated "the Mechanism password-recovery is enabled". so I followed the procedure Cisco
I go flash_init: OK but when I type "load_helper" Unknown command it say to me .... I'm stuck!
The model is my Cisco: Cisco WS-C2960G-24TS-S
SW Version 12.2(55)SE3
Sw image C2960S-UNIVERSALK9-M
View 3 Replies
View Related
Oct 2, 2011
I have a couple of 877s which have "no service password recovery" set and something has happened to the flash or the IOS has been lost for one reason or another.
When trying to boot the routers, they all display similar to this, which then repeats:
[code]....
Or words to the effect of there being no IOS at all, unable to boot, but the result is the same, it just loops and there's nothing I can do to break the sequence!
I've tried taking the flash from a working 877 and replacing the card but this doesn't work and unfortunately, putting the once working strataflash card back in the working 877, it gets the same problem!
View 11 Replies
View Related
Jun 26, 2011
I have a cisco 515e pix but where I bought it from did not get the machine back to default. I boot it up and get to the user prompt, type enable and it asks for a username and then a password. I am new to this and am have no problems with router and switch password recoverys but when I look at the cisco documentation it is a bit overwhelming and I am not quite sure what it is that they want me to do to fix this. I have downloaded all the password recovery software loads and have the one I need for 6.x which is what the box is running I am just not sure what it is that I need to do. Can I use that recovery software from directly from my pc using a tftp server?
View 1 Replies
View Related
Aug 3, 2012
I need to recover switch enable password, i have already configured AAA also, when i am tryig to follow below proceedure finally saying Authorization failed. how can i recover enable password,If I try to recover password like this description says [URL]
Step 1 Connect a terminal or PC with terminal-emulation software to the switch console port.
Step 2 Set the line speed on the emulation software to 9600 baud.
Step 3 Power off the switch. Reconnect the power cord to the switch and, within 15 seconds, press the Mode button while the System LED is still flashing green.
Base ethernet MAC Address: 00:0x:xx:xx:xx:xx
Xmodem file system is available.
The password-recovery mechanism is enabled.
The system has been interrupted prior to initializing the flash filesystem. The following commands will initialize the flash filesystem, and finish loading the operating system software:
flash_init
load_helper
boot
[code]....
View 1 Replies
View Related
Oct 17, 2011
where I can find a CLI password recovery procedure for the administrator account?
View 2 Replies
View Related
Sep 26, 2011
I was just configured a 3800 router with this command. I cannot get to the ROMMON mode anymore. Cisco says you should press Break key within 5 seconds after the image decompresses during the boot. But mine is ignoring it and going to load running config directly.
View 7 Replies
View Related
Nov 27, 2011
I have a 4404 running firmware 7.0 and something happened (don't think it was a hack), but all of a sudden I can't login to the box via web or ssh or even telnet.
In trying the recovery procedure, I get a lot of messages scrolling through and cannot do the Restore-Password command on the CLI.
I'm attaching the whole capture, but here's a truncated capture from the procedure:
*fp_main_task: Nov 21 10:39:46.501: sshpmGetCID: comparing to row 0, CA cert >bsnOldDefaultCaCert<
*fp_main_task: Nov 21 10:39:46.501: sshpmGetCID: comparing to row 1, CA cert >bsnDefaultRootCaCert<
[Code].....
So as you can see, my prompt to enter the command is taken up by this fp_main message and it uses up the first and only time I can enter this in. I'm trying everything I can to not have to go back to factory defaults.
View 24 Replies
View Related
Aug 23, 2012
How is-it possible to do a recovery password for sysadmin on ADE-OS ?We're using LMS 4.2.1 and my customer doesn't remember the username and password created during installation.We have the admin user for the https connection.
View 4 Replies
View Related
Sep 19, 2012
I wanted to do with my Cisco 2800, a password recovery. I have read the instructions and Cisco just came up at six.
Complete these steps in order to recover your password:
Shut down the router. Remove the compact flash that is at the back of the router. Power on the router. Once the Rommon1> prompt appears, enter this command:
confreg 0x2142Insert the compact flash. Type reset.
BUT I had forgotten to plug the flash card. And now comes via console hieroglyphics only
View 1 Replies
View Related
Jan 7, 2013
I have 3 x ASA 5510 & 2 x ASA 5520, that require resetting back to factory default, the customer has removed the External Flash Cards, and i've checked internally on each unit the Internal Flash car is still present, is it possible to run a password recovery then a factory reset? and how would i go about resetting each unit to the new configuration.
View 8 Replies
View Related
May 31, 2010
the " password recovery functionality is disabled " service is running on the system .
im trying to access rommon in a Cisco 851, with not much success, i am sending a break after the image is loaded ( in the time frame that is allowed for that) .
View 13 Replies
View Related
Jul 4, 2011
I have a cisco PIX-515e which i have connected to a emulator through the console port, and im having trouble erasing data from it. I can get into 'pixfirewall' mode and 'monitor' mode but thats as far as i get. i have tried 'write erase' and 'configure factory-default' in both modes to no success.
View 11 Replies
View Related
Mar 24, 2012
I am studying for the CCNA and have my own lab. Several months ago I setup the lab and hand things running well, and decided to put it all away for a while. Alas, now that I have brought it all out again, I don't remember the passwords I used and have since destroyed my documentation, so this is perfect practice at password recovery/config maintenance type of stuff.
I am working on a 2610XM. When I power on the router, I see all the information pasted below. I have tried the password recovery processes described in the cisco knowledge base where we use the rommon prompt to load 0x2142, reset, then enable secret <password> and followed the remainder of the instructions, but when I reload the router after the process, the new password I've set still does not work.
Some things that are not consistent from the documentation that I am seeing are the messages Slot is empty and WIC is empty.
I am wondering if my router does not use 0x2102 for it's load, but it will not show what it is using and I can't run show version because of the password. I am connecting through the console port and using putty to access and configure. Below is a paste of the startup messages after the router decompresses it's image.
Processor board ID JAD070709N9 (1997350087)
M860 processor: part number 5, mask 2
Bridging software.
[Code].....
View 6 Replies
View Related
Jul 20, 2008
how to password recovery Wireless LAN Controller 4402
View 3 Replies
View Related
Sep 17, 2012
I am trying to use the password recovery for an NME-16 and am having trouble. I am unable to look at my files in dir to so I can rename them. I can get the switch to bypass the config and come with the switch: prompt, but can not do anything more. I am trying the password recovery guide, but cant get to the text file to rename. I am using a 2811 router.
View 2 Replies
View Related
