I have a cisco PIX-515e which i have connected to a emulator through the console port, and im having trouble erasing data from it. I can get into 'pixfirewall' mode and 'monitor' mode but thats as far as i get. i have tried 'write erase' and 'configure factory-default' in both modes to no success.
View 11 RepliesI need to recover the passwords for my 3750 stack (2 switches), I have the password recovery documentation but it seems to be referring to recovery for one switch. How do I go about recovery when in a stack, should I remove the links on the switches and recover each one separately?Alternatively can I do a factory reset on them
View 1 Replies View RelatedIm connecting to my firewall through the console port, and need to know how to reset it to factory defaults. I have looked around online and can not see any reference on how to do this.
View 11 Replies View RelatedPIX-515e reset to factory defaults
View 6 Replies View RelatedI have completed my CCNA qualification and i am doing some volunteering for a none proffit eletronics recyciling company they receved some cisco pix 515e firewalls and i was aloud to keep one so i can learn how hardwaire firewalls work and how to set them up but i can not seem to connect to it is there a way to completely reset the device to factory settings without any ip address or passwords i do not have any cables for the device but i have made a straight and cross over cable and there is a box of cables at the recyciling company from diffrent places if i need a specialist cable i may be able to find one
View 6 Replies View RelatedI have a cisco 515e pix but where I bought it from did not get the machine back to default. I boot it up and get to the user prompt, type enable and it asks for a username and then a password. I am new to this and am have no problems with router and switch password recoverys but when I look at the cisco documentation it is a bit overwhelming and I am not quite sure what it is that they want me to do to fix this. I have downloaded all the password recovery software loads and have the one I need for 6.x which is what the box is running I am just not sure what it is that I need to do. Can I use that recovery software from directly from my pc using a tftp server?
View 1 Replies View RelatedMy bussines have an old PIX 515e and im about to install it in a "testing" eviorment but no one can remeber the password for this old equipment. Is there a way to reset the password?
But when it reboots and I write "enable" in the console it asks for a password, and the password isn't "cisco" as factory default. I really need this firewall up and runing ASAP.
How to reset the "enable"-password?
I have Cisco PIX 515E for my Lab and can't recover the password. It is not connected to the network. I have configured server, address, gateway from the monitor mode and tftp not seeing my laptop. best way to reset or recover password.
View 7 Replies View RelatedI recently decomissioned an 871 from a small business site and the owner did not want the device anymore. So now I'm trying to use it back at the office in the sandbox, however I don't know the password to the device and neither does the business owner. There's a reset button on the back, but from what I've read (here), it only loads a different config file found on the internal flash. Tried this, no dice. Is this essentially a bricked router now or is there anything else I can do to clear the config and repurpose it for my use?
View 7 Replies View RelatedI was trying to do a password recovery on a 1142 AP but enable password did not reset and I am stuck
AP model is AIR-AP1142N-A-K9
Running IOS c1140-k9w7-mx.124-21a.JA1
Its autonomous so there is no controller. I renamed the config.txt file I am unable to rename or delete the private-config file. I get the message that file or directory cannot be found when i try to rename and permission denied when I try to delete it.
Im trying to access the switch to reset the password to factory defaults (please see switch output Astrix has removed customer identifying information for security purposes.) Each time I reboot the switch and try and access the password recover mode this same output below starts and im still not able to access the recovery area of the switch
cisco WS-C3560G-48PS (PowerPC405) processor (revision F0) with 122880K/8184K bytes of memory.
Processor board ID FOC1133Y28Q
Last reset from power-on
1 Virtual Ethernet interface
52 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.
[code]....
i need to recover a router Cisco 2801. I lost the password and the "no service password-recovery" is configured. I have done many attempts with the procedure in this link :URL
View 9 Replies View RelatedI have a cisco PIX-515e which i have connected to a emulator through the console port, and im having trouble erasing data from it.
I can get into 'pixfirewall' mode and 'monitor' mode but thats as far as i get. i have tried 'write erase' and 'configure factory-default' in both modes to no success.
I forgot the user for management a IPS SSM-10, when i follow the procedure to reset the password for cisco user, i can get into the module, i change the password and every thing is OK, but when i tried to configure y don´t have rights to do anything.
if i see the privileges for the user cisco this is the result. [code]
I've inherited a IAD2430 router but I don't have the ena passwords nor am I able to do a break and do a password recovery. I'm familiar with the password recovery process and config reg settings but this one has me stumped.
The config register is set to 0x2102 so I see nothing at all when it boots until it's completed and I get the prompt to "Press RETURN to get started!" I get to non priv mode but without the password obviously I'm going nowhere at that point. All the docs I've come across so far assume you can break out of the boot process or are already in rommon. When I remove the flash: I get no output at all... The IAD has no "reset" button like the CAT switches either..
I don't need the current config, just a reset/format of the NVRAM.
My team already bought one 1800 Series router. And they setted some passwor.
Right now i am not able to login. I know the cisco password recovery method to reset the password.
Instead of password recovery method i want to try with total factory default setting.
is there is any method to do factory default without login
I got a ASA5505 back from a Office. I don`t know the IP Address to connect to the ASA. How can i reset the System to the Factory Settings.
View 1 Replies View RelatedI have an AIR-AP521G-E-K9 and i want to reset to factory default in CLI.I tried "write erase" but dont work.I have problems with access-list and i want to desactivate access-list that i have created by web GUI.The problems now is that i can not access to my AP, no ping, no web GUI access.Access that i have is only by CLI, but access list is always blockinh all tha traffic trought my AP.How can i desactivate mac filtering, or how can i reset to factiry default
View 1 Replies View RelatedWe've recently changed data line providers and now have some Cisco 877 routers we'd like to reconfigure and use at other sites. Although we own these, they were configured by our old data line providers, I'm having a hard time of resetting them to factory defaults. The simple, hold down the reset button until it restarts does not work.If I press the reset button within 5 seconds of power up to load the default rom image, I get the below:
System Bootstrap, Version 12.3(8r)YI4, RELEASE SOFTWARE
Technical Support: [URL]
Copyright (c) 2006 by cisco Systems, Inc.
C870 series (Board ID: 1-148) platform with 131072 Kbytes of main memory
Booting flash:c870-advipservicesk9-mz.124-24.T.bin
Error opening: flash:c870-advipservicesk9-mz.124-24.T.bin
[code]....
I assume from this the required bin has either been removed, renamed or overwritten.As soon as the router boots it requires a password and I dont have the password to be able ftp files in and out of it.
i got the ACS 5.1 at work..after migrating the data from 4.1 a lot of data got changed into the 4.1 so I needed to reset my configuration (since i played around with the 5.1)after doing so, I can't access the web page, to start the configuration again tried the administrator-setup but it didn't work,
View 1 Replies View RelatedI can't figure this out and there isn't much documentation on the subject online. The reset button just resets the device even after holding it for 10+ seconds and there is nothing in the CLI.
View 5 Replies View RelatedI successfully pulled it out of the box and already broke it.
What I did to lose my connectivity to it (via IP, console is OK), but I'd like to start from scratch and during my learning/experimentation I will undoubtedly need to do this over and over until I get things right.
I've found various guides, none of which look like what I am after. Basically, I want to return this to the condition that it was in when it came out of the box. IOS is version 12.4(6)T11 .
I put a config on this switch and it is having some issues I would like to take it back to out of the box state however I am not sure how to do this ? I do not need to blow away the IOS just the config I put on it
Cisco IOS Software, C3560 Software (C3560-IPBASEK9-M), Version 12.2(50)SE5, RELE
ASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 28-Sep-10 13:21 by prod_rel_team
Image text-base: 0x01000000, data-base: 0x02900000
[code]....
I am trying to factory reset CE500 switch, as described in the factory rest section of the documentation. I do not get an IP address via DHCP from the switch.
On boot up I hold the setup button down, wait till the lights go solid amber release setup. wait for a port on the switch to start blinking green port 1 starts blinking green, plug my pc into port and wait for IP..and keep waiting !!!!
I have tried this on 3 switches now all with the same result.... NO IP offered.
How to reset a CAPWAP AP3600 to factory default using the AP's CLI and not the controller.
View 2 Replies View RelatedThe IP address is unknown and we need to reset the switch. SInce we can't access the configuration menus. I was wondering if we could reset this device to factory defaults another way. I couldnt locate a reset switch.
View 2 Replies View RelatedI have a WRV210-A V01 (Software: 2.0.1.5) router that when originally purchased I upgraded the firmware to the newest 2.0.1.5. However after the firmware upgrade the router has not worked right since. [I thought maybe the upgrade did not take, and successfully pushed the firmware 3x times]
Everytime you login to the webpage the right-side pane you have to scroll down 3x pages until you can see the settings options. It does that for everypage you visit you have to scroll down 3x pages until you can see the settings.
The wireless is sporadic and dropping connections, and now certain options like changing the "Basic Rate:" from "All' to "Default" does nothing and wont let you change it.
The main issue I have is that certain wireless settings like changing the "AP Isolation:" cause the router to reset back to factory defaults. and even trying to configure the LAN setup also randomly makes the router reset to factory default.
Is there any possible way to factory reset an AIR-AP1231G-A-K9 that was once attached to a WLC via SSH? I dont have physical access to it and the old WLC has long been decommissioned. I have tried the clear command but since it is in CAPWAP mode that command has been disabled. I know I can press and hold the mode button and reset it that way but I need to know if its possible through SSH to be reset. I have two that are in need of being reset in order to connect to the new WLC.
View 21 Replies View RelatedUnable to log in into our new ESW 540 switch because the default User ID and PW was changed. How do i restore the factory default on the switch.Can't get into the switch with CCA or explorer.
View 1 Replies View Relatedi have a new 5505 and i have done a few configurations on it. When i try to reset it to the factory settings via asdm i get an error saying it could not be done. I have used config-factory-default using the cli option available in the asdm. I am using asa 8.2 and asdm 6.2. Will erasing the flash reset to factory defaults.
View 4 Replies View RelatedI use Cisco switch sg300-28. When i turn it off and turn on, it reset to factory reset include login password, dose it normal operation or I miss anything?
View 2 Replies View RelatedMy company just bought a SF300-24P, got it configured without much issue. Today I try to get into it and I can't. Tried via HTTP and console and nothing happens. Decided to try to reset it using the button on the front. Using the documentation, I held down the button for over 10 seconds. Didn't reset to factory defaults, tried again and rebooted it, still nothing. What I am I doing wrong. Also nothing comes up on console window and I'm using the setting for Hyper Terminal that the documentation says I should use.
View 5 Replies View RelatedI am locked out of my Arris wtm652 (unable to login with default password or the password that i set). I have tried every way I know of to reset the modem outer to its factory settings but to no avail. I know that it is not being reset because I still can not login to it and it is maintaining the wireless security settings that were set for it.
View 1 Replies View Related