We have a 3750x switch with some issues on the arp. Our servers become unreachable for some time, buy when I clear the arp cache, I am able to ping the server again. I have tried adjusting the arp timeout but I don't think doing so would be the permanent solution.
View 9 RepliesWe have several 3750 stacks across our campus that we are unable to completely clear port security on. We have mac address stick set up on all access ports. When we clear the sticky address on the port, the mac address is removed from the running config like normal, but we keep getting port-security voilations. If port security is taken off the port completely, i.e. no switchport port-security, traffic still doesn't pass the port. Even clear port security across the stack doesn't work. If we try to reload the stack, only the master reboots, and the other switches in the stack lose switch capabilities.
View 1 Replies View RelatedI develop websites, and we moved a site from one server to another, and now I get the message the site has moved. I ran the cmd to clear the dns cache, but that didn't solve the issue. I tried stopping and restarting the client, that didn't work. It was already set to automatic. I am logged in to my laptop as an administrator. I tried to be the user Administrator, but it doesn't appear as a choice, but when I try to change my name, I get the message it is already in use. I am using XP Pro, SP3?
View 3 Replies View Relatedwhen i try to get on my network it keeps coming bk have to clear arp cache so i do the repair and it does not work becoz it cant clear it
View 2 Replies View RelatedHow do I clear my router DNS cache on my ZyXEL P-660 router?I already cleared it on my PC with "ipconfig /flushDNS" in the command line but everyone sees my online IP camera, except me my online IP camera on LIVEwhen I try to access the camera URL i go to the router default/settings/home page
View 10 Replies View RelatedEvery 2 minutes, I want to clear it, because some machines will be turned off. Currently, they will stay on on the left hand side of my host's window explorer.
View 1 Replies View Relatedclear ARP cache from server side?
View 12 Replies View Relatedi have a wireless-g broadband router and the cache is giving me headaches as i cannot access certain of my sites on a server in USA.
View 4 Replies View RelatedI have been encountering a can't find server (not page not found error 404) message in two ways. Either using a hyperlink to open a new web page or returning to a tab will yield this error. Refreshing the page will render the page properly.The two cures I have found that look to be the most promising are to run ipconfig /flushdns from the command prompt and to clear the prefetch cache.
View 18 Replies View Relatedcannot access internet from desktop Gateway WIN XP Mozilla FF Tried ARP cache clear -- went to DOS -- didn't work Tried Admin Tools, comp mgmt, services, routing/remote changed to disabled -- didn't workNow what?
View 1 Replies View Relatedwhen i try and repair it it comes bk saying cannot repair ip address coz cant clear arp cache
View 1 Replies View RelatedI configured an DHCP server on cisco 3750 switch . Wher in w3750 gets connected to plain l2 switch 2960 on floor and machine gets connected to 2960 port. [code] Below is the description of problem:
-> The Cisco 3750 switch is the DHCP server. VLAN 108 is named as internet vlan.
-> Ports in Cisco 2960 switch has been configured with "switchport access vlan 108".
-> There were no problems at all and everything had been working smoothly.
-> 3 days back, users started complaining that they couldn't access the internet. Up on troubleshooting the issue, I found out that there was an issue with the DHCP server as the computer couldn't get any IP address at all. After setting static IP address, the internet started working again.
If I bind IP to MAc address reservation on core 3750 switch for some time of moment it works but after that machine gets unreachable .I restarted the 3750 switch and also all the 2960 switches over the weekend, however, the issue still hasn't been resolved yet. I did issue the command "clear ip dhcp conflict *", clear ip dhcp binding * but no joy at all.
i have an issue to connect a trunk between cisco switch and extreme switch i have many vlans that i want to cross via a link between cisco 3750 switch and a Extreme Alpine 3800 switch
View 12 Replies View RelatedI have two 3750-X configured to be a stack and I am planning to re-rack these somewhere else. What I would like to know is what are the effects of having the master switch itself lose power? Does it immediately just make the member take over master (there should be no election since there are only 2 switches??) and there would be no loss of connectivity?
View 1 Replies View RelatedI have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net.
My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20
I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2)my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to go out to the internet. I think it has to do with the routes. [code]
I have the task of replicating the router config on a 3825 router on a 3750 switch. Reason is we are taking out the router and replacing it with the switch to make use of the router for other functions.
Below is main part of the router config:
!
ip source-route
ip cef
!
!
multilink bundle-name authenticated
!
license udi pid CISCO3825 sn FCZxxxxxxx
!
vlan internal allocation policy ascending
[code].....
The 3750 switch I have runs C3750E-UNIVERSALK9-M, Version 12.2(55)SE3 on a LAN BASE license.
The first thing I have done is to order for a license upgrade to IP BASE which would give the support for OSPF routing.I do not see much of an issue with the Interface configs, however, I am not too sure about replicating the routing config on the switch.
My question is can I run the commands as shown for the OSPF routing on the switch? If not, can I get suggestions on how best to set this up on the switch?
I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net. My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20,I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2),my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to,go out to the internet.
View 3 Replies View RelatedI'm running into what seems a basic ip routing config problem with a Catalyst 3750 (IP Base) switch. I have several VLANS configured on the switch with IP routing enabled, and the switch is connected to the inside interace of a new ASA 5520 as follows:
ASA5520 IP (Default gateway): 192.168.1.1Switchport Gi1/0/1 is configured as a routed port, IP address 192.168.1.3 255.255.255.0Example VLAN is VLAN 100, IP address 192.168.100.1 255.255.252.0 From the switch CLI, I can ping all VLAN addresses, as well as the ASA5520, and the client laptop I'm testing with from VLAN 100.
From the client laptop on VLAN 100, I can ping all switch interface and VLAN addresses (inter-VLAN routing is working), including 192.168.1.3, but I CANNOT ping the default gateway at 192.168.1.1.
Here is the relevant configuration information on the 3750:
!
no aaa new-model
switch 1 provision ws-c3750x-24
system mtu routing 1500
[Code]....
configure qos in Cisco 3750 switch.I have configured below template and applied on the vlan interface.But i am getting the hit on the access list but I am not able to get hit on the class map.
View 2 Replies View RelatedI had a bad expirience with Switch 3750-X. Because of an auditing security processess, my customer ran a software called "Nessus" to do a scanning of vulnerability on the network. When this software is point to switch, the process of the switch will next to 100% and reset. The software only do a listening on the ports to see what ports are opened and the switch should not reset because this. Bellow is the log os switch on the moment of test; we note that the processess 'HTTP' rise moments before the switch reset. I disable the HTTP service on switch but the problem persist. The test was made only one machine connected to switch.
View 4 Replies View RelatedWe have three Cisco 3750 - 48port POE -LAN switches and i am trying to see if there are any issues when we stack POE and Non-POE type of switches.Aslo looking for information on the advanatage and disadvantage the stacking can provide on a Cisco 3750 48port.
View 3 Replies View RelatedThe question is: Will a 3750 switch route Jumbo frame sizes (e.g. 9000 MTU)?
We know that we can change the System MTU to 9000, and someone on a previous thread said that we can change the Routing MTU to 9000 as well, although I couldn't figure out how to do that. However, regardless of how we configure the System MTU and Routing MTU, I don't think we're able to adjust the MTU on L3 VLAN interfaces, so if we want to actually "route" between VLANs on the switch, we're limited to 1500 MTU.
Our situation is that we have a customer connecting to our 3750 switch, and this customer wants to use Jumbo frames. The customer connects to our 3750 switch via their own VLAN, with their own L3 VLAN interface configured on the switch. The customer will point their traffic towards the L3 VLAN interface, then we want to route them onto another VLAN, via a different L3 VLAN interface, before forwarding their traffic. Because of the limitations noted above, specificially regarding the routing between these VLANs via L3 interfaces, I do not think we'll be able to support 9000 MTU frames on this 3750 switch. I think the L3 VLAN interfaces will limit us to 1500 MTU, regardless of what we configured via the global System MTU and Routing MTU settings.
How do you properly remove the QOS queues and configs from the switch.A was using auto qos which created a whole mess of qos configs on my running-config. I did "no mls qos" in conf term but that did not remove the queues.
View 3 Replies View Relatedi want to remove an access layer 3750 48 POE master switch and replace with a new 3750 switch in the stack. i want to copy the same configuration to new switch since the old switch is having POE issue and I got replacement of the malfunctioned switch. we have VTP domain is configured in the network...
View 3 Replies View RelatedCisco 3750, I'm trying to reset the password but cannot communicate with my switch
View 1 Replies View Relatedis it generally possible to connect another switch, such as a 3750 to a port of a fabric extenders (C2232PP-10GE)?
View 1 Replies View RelatedI have Layer_3 " 3750-x " , so I can't do any routing on the switch , so if I need to Upgrade the IOS what is the proffered image that support hte routing , and Is it free or should I pay?
View 7 Replies View RelatedIn Cisco 3750 facing high CPU utilization for specific period. During this period traffic response times across the switch degrades. Steps to identify interface potentially generating traffic. I have attached 'sh proc cpu history' , ' sh ip traffic', 'sh proc cpu sorted' during troubled period .
View 5 Replies View RelatedI have a 2 member 3750-x switch stack that was upgraded to 15.2 today via CNA. All the files were transfered and expanded correctly and it got to the step where the switches needed to be reloaded but on reload they froze.
I connected a console cable and power cycled the stack. I see the flash initialize and then the IOS image start to load. Lots of @ symbols and then nothing. It just sits there. The system light on the switches, while flashing green during the load, is now off. No light at all. But fans are running and the process will repeat itself if power cycled.
i have standalone 3750 switch. RPS light is green and system light is off.
3750TS#sh env all
FAN is OK
TEMPERATURE is OK
[Code].....
i have another switch with same model and ios its RPS light is off and system light is green
We currently have a stack of 5 x 3750 switches and i want to remove switch number 3 (it has the least number of things plugged in). What will happen to switch 4 and 5 will they be renumbered 3 and 4, and will the config automatically update this if it does?
View 2 Replies View RelatedI configured 3750 A switch with vlan 20 and its IP address 192.168.20.41Its default gateway was 192.168.20.3Then i configured 3750 B switch with same default gateway and vlan 20 IP 192.168.20.43My question is now when we stack it becomes single switch and now vlan 20 ip address is 192.168.20.43 thats only IP i can see.So how does stack switch choose vlan 20 IP?Does it choose highest IP address between two switches if they have same vlan 20 as in my case?Also when i go to switch 3750 b by session command and do sh ip route it does not show ip default gateway .Also it shows vlan 20 as admin down .
View 5 Replies View RelatedI have a doubt. In my environment I have two Switch 3750-X in stack.
My question is: How to shutdown remotely only a switch in stack?