Routers / Switches :: How To Reset Router Constantly
Aug 4, 2011In the last month or so I have had to reset my router every 30 min or so this is very annoying and would like to know what could cause the problem.
View 2 RepliesIn the last month or so I have had to reset my router every 30 min or so this is very annoying and would like to know what could cause the problem.
View 2 Repliesi cant use a new tablet i bought due to i can't remeber pas word for router it was such a long time ago it was installed
View 2 Replies View RelatedCan't reset password on router, have followed steps. want to secure network
View 2 Replies View RelatedI am unable to connect to the internet thru my router, Lynksys WRT54Gs. The network worked fine before I went on vacation. I accessed the internet by connecting the ethernet directly to the modem, and have been unsuccessful at my attempts to reset the router with 192.168.1.1
View 1 Replies View RelatedI recently purchased a newer Netgear wireless router ($50 or so) to replace an old one because I was constantly having to reset it to successfully get an internet connection on my computer, my phone, and our wireless printer. Now, the computer and phone have no problems picking up the network, but I always have to reset the router to get the printer to pick it up.
View 9 Replies View RelatedI lost my 192.168.1.1 password and how to reset it?
View 1 Replies View RelatedI just moved into a new place and I've been having a lot of trouble with the wireless connection. There are 4 other people sharing the wireless and none of them seem to have problems, and my phone connects fine, but my laptop will randomly lose internet access while still detecting the network. When I run the troubleshooter it says it has reset the wireless adapter, and the connection will work again, but sometimes only for a few minutes before it craps out. I don't have access to the wireless router itself, so doing anything with that will require asking the landlady (who doesn't speak English well). I had access fine for the first two days after I moved in. I did install a couple of programs after that: 7-Zip and Flash Player 11.2 (since the newest Flash version crashes my Firefox). I don't know if that could have anything to do with it.
I'm running Windows 7 64-bit on an Asus laptop. After searching around the forum a bit, I followed the instructions in this post and will paste the results here. I don't know if the ping address starting with 206 might be invalid since the post is from several years ago.
C:UsersLindsay>IPCONFIG /ALL
Windows IP Configuration
Host Name . . . . . . . . . . . . : Lindsay-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
[code]...
how to reset nokia siemens 1600 modem as i have forgotten its username & password which i changed?
View 1 Replies View RelatedI own a HP laptop (runs Windows 7), and lately when I either turn it on or log back in for the first time in a day, it's not connected to the internet, despite my brother's desktop computer (Windows XP) being connected (it's right beside the router and modem). Before, we would have to just unplug the router for a few seconds and then plug it back in again to get the connection to work again on my laptop, which that alone we don't understand why, as there are periods of time we have no problems connecting on either end, like I just bought this laptop at Christmas and have had no connectivity problems until now. Now however, when we unplug the router and plug it back in, it kicks my brother's computer off the internet despite his connection being good prior to, apparently it loses its IP address when we do that. So then we have to unplug/replug the modem and router plus sometimes restarting my brother's computer to finally get it working again.
View 3 Replies View RelatedI have a SF 200-24P Cisco switch that seems to be rebooting constantly, When i connect it to mains power it seems to go through a startup cycle, in this order - i have tried this with no network devices attached and the same thing happens
1. Fan starts - continously runs
2. Very quick flash of all RJ45 ports.
3. After about 30 seconds, any network devices connected have an acticity light
4. After about another 45 seconds, all ports light up including the activity and POE orange LEDs for about 5- 10 seconds then go off.
5. About 10 seconds later the ports all light up again and stay on for about 5 seconds.
6. All ports go off and the cycle keeps repeating continously.
I have tried pinging the switch without success.I have also tried disconnecting all devices from each port with no success.At no time does the system LED on the left light up.I have tried resetting to factory default with reset pot on the left side.This is a brand new shipped switch from our cisco supplier, could it be DOA?
My problem is that the switch all of the sudden doesn't boot up anymore. The System LED constantly flashes, after probably 40-50 seconds or so it constantly lights for a second, afterwards all the lights on the ethernet ports light up for a second and the process starts all over again! The console messages:
Device configuration:Slot 1 - SG300-10PDevice 0: GT_98DX3033B (AlleyCat2)
-------------------------------------- Unit Standalone --------------------------------------
Tapi Version: v1.9.5Core Version: v1.9.519-Jul-2012 17:55:03 %INIT-I-InitCompleted:
[Code].....
I have a Cisco SG300 switch on which trunks are configured. I have a server which sits on the switch via a trunk link of four network cables (4 Gbps total)on which LACP is enabled. I'm having trouble connecting to the server using VNC from a computer on the network. It doesn't happen all the time though, it's just random.
On looking at the logs of the switch, I saw something unusual. The trunk that connects the switch to the server is constantly removing all the member ports and adding them back again after a few minutes interval. That causes the trunk link to flip on and off all the time. What could be the reason that's causing it to happen? I know it could be the network cable but I'm using brand new cables and the server also is brand new.
I have a conflict with my satellite Internet connection between the modem and router IP addresses. I also somehow entered a password for the router which I now cannot duplicate. received a request for additional information which I responded to in September. I attempted to follow-up in October again, but I have not received any reply since the first one on August 11, 2011.
View 1 Replies View RelatedI want to setup an home network with a wireless router and use multiple switches for wired connections through out my home. I currently have an Airport extreme hooked up to a cable modem and a leviton gateway hooked up to the Airport. The 2 computers connected to the Leviton are on a windows 7 homegroup and share fine, but won't share or discover any wireless device connected to Airport. My main goal is to have a wireless/wired network with all computers sharing information with each other. I want 2-3 wired switches/gateways with a min of 2 devices connected to each, connected to my wireless router whiich is connected to cable modem.
View 3 Replies View Relatedhow to connect two subnets with two switches and one router using router sim software?
View 1 Replies View RelatedF7D2401 was constantly dropping out fixed the problem through the server but now my iPad and toshiba lap top wont join just say unable to join network but phone and other iPad are working fine
View 2 Replies View RelatedI have been having a lot of trouble lately with my wireless network. Basically, under certain situations it will constantly drop out, by which I mean all computers will lose connection with the wireless network for about 30 seconds and then reconnect.This is happening with two different wireless routers so I don't exactly know what is happening. I usually use a Linksys WRT54GS v7 but after this started happening I borrowed a friend's Linksys WRT54G2 v1 router to test it out with no change. I also updated both router's firmware last week, and changed both router's channels to 1 in case that was a part of the problem. To clarify,only one router is being used at a time, I have just tried different steps with each one.The other day when it was happening repeatedly, I connected one of the computers directly to the modem and had no problems so I do not think it has anything to do with my modem. On the network, depending on the time of day, there will be any combination of three macbooks running the latest version of snow leopard and one older PC running Windows XP. The network can drop out with only the PC, no PC, or any combo of macs. There can also be two iPhones and a Blackberry using the wireless depending on who is home. The most consistent problems seem to occur whenever something is being uploaded. We seem to get major issues when my wife is sending relatively large files (5MB+) using her macbook's mail program (either sending through gmail or her work address). However, yesterday it was happening every 30 seconds when someone was talking on skype on her macbook while there were two other macbooks connected to the network but doing nothing more than using a browser for basics like google.I have also noticed that this will often happen, though usually only once rather than repeatedly, when a computer that hasn't been on is turned on.
View 19 Replies View RelatedI have a SRP527W what has a constantly flashing power LED.Is there anything that I can do to attempt to recover this router?
View 2 Replies View RelatedI have an RV016 V3 with firmware 4.2.1.02 that is constantly rebooting making it unusable. I have one LAN connect and 3 WAN's, 2 DSL's and one Cable Internet in a load balance config. I have tried firmware 4.2.1.01 and it reboots also. do I get and RMA from Linksys and send this pig back?
View 6 Replies View RelatedMy F5D8235-4 v3 constantly looses it's DHCP service and needs to be rebooted.
View 1 Replies View RelatedBelkin storage manager sees my 8Gb flash drive for a split second and the pops up a message about unmounting. When it connects for a split second it shows up wit a drive letter, but then disappears again.
View 2 Replies View RelatedI have recently purchased a Belkin n300 wireless N router. The problem is, I have to reboot the thing numerous times throughout the day to allow a client to connect to it via wireless. One client will be connected and then drop, or a client will be connected, and I cannot connect another device. I also had an issue with streaming over wireless for netflix on my devices and the only way I could get it to work was to turn off the firewall, what the hek.... This is crap. I knew I should not have bought a belkin router again. Had one years ago and it constantly gave me issues. Had my Linksys Wrt54G for years with no problems until it finally crapped out. Anyways, my firmware version is the latest version according o the website.
View 6 Replies View RelatedI have been asked to do a network survey at a client. They are using the Cisco SGE2000 switch, which is new to me (used to working with 3750 switches). They seem to have lost the username/pasword for one the switches. Is there an way to recover from this, without reseting the whol config (not sure they even have a backup) ..
View 1 Replies View RelatedI have a problem with my SG200, maybe more than one.
I tried to update to 1.3.0.59 this morning. It succeeded and the switch was restarted. After the restart I could no longer log into the switch. I tried to reset the switch but it still will not let me log in. I also tried to log into the switch using the forllowing method but I still cannot log in. I unpluged everything, held the reset for at least 30 seconds, waited 3 minutes, plugged a computer in and set it up to see the switch. All worked there and the login page appeared. It still would not take my login dredentials nor wold it that the default credentials. I has access through the switch but connot configure anything.
The IP address is unknown and we need to reset the switch. SInce we can't access the configuration menus. I was wondering if we could reset this device to factory defaults another way. I couldnt locate a reset switch.
View 2 Replies View RelatedI can't seem to reset my switch and realized the reset button is missing/broken off. Is there an alternate method to reset the switch to factory settings? If not, how do I figure out the IP of the web interface, it is not the default.
View 8 Replies View RelatedUnable to log in into our new ESW 540 switch because the default User ID and PW was changed. How do i restore the factory default on the switch.Can't get into the switch with CCA or explorer.
View 1 Replies View RelatedI have been fighting against this Lynksys cisco switch to be able to restore admin password, no success. Theorically, is just unplug and plug switch, press ESC and press option 3) Password Recovery Procedure. Then Enter and Enter and switch will boot normaly with admin/blank password, well, not work,.
*******************************************************************
*** Running SW Ver. 1.2.1b Date 31-Aug-2006 Time 13:47:21 ***
*******************************************************************
HW version is 00.03.00
Base Mac address is: 00:1e:e5:1c:fd:eb
[Code]......
I use Cisco switch sg300-28. When i turn it off and turn on, it reset to factory reset include login password, dose it normal operation or I miss anything?
View 2 Replies View RelatedMy company just bought a SF300-24P, got it configured without much issue. Today I try to get into it and I can't. Tried via HTTP and console and nothing happens. Decided to try to reset it using the button on the front. Using the documentation, I held down the button for over 10 seconds. Didn't reset to factory defaults, tried again and rebooted it, still nothing. What I am I doing wrong. Also nothing comes up on console window and I'm using the setting for Hyper Terminal that the documentation says I should use.
View 5 Replies View RelatedI have a 1 month old SG200-26P - the green status LED is blinking constantly (> 30 minutes), I cannot access the webGUI, nor is it responding to ping. I have tried resetting via holding reset for > 10 seconds with no effect, the status/activity LEDs are still illuminating against all connected ports, excluding any of the PoE ports which are running a couple of cisco IP phones. I've tried accessing the device via both the static IP I configured, and the default IP.
I have disconnected all ports, then powered on the device, but same results...Do I have a dead switch? Anything I can do other than return for warranty claim which is going to be last resort due holiday period and leaving the customer offline for extended period...
I have a 1 month old SG200-26P - the green status LED is blinking constantly (> 30 minutes), I cannot access the webGUI, nor is it responding to ping. I have tried resetting via holding reset for > 10 seconds with no effect, the status/activity LEDs are still illuminating against all connected ports, excluding any of the PoE ports which are running a couple of cisco IP phones. I've tried accessing the device via both the static IP I configured, and the default IP.
I have disconnected all ports, then powered on the device, but same results...
Do I have a dead switch? Anything I can do other than return for warranty claim which is going to be last resort due holiday period and leaving the customer offline for extended period.
I reset my router (WBR-T2) a fews days ago and now I cannot connect to internet (although I can connect to the router - local only).
View 6 Replies View Related