Cisco Routers :: RVS4000 Connects To ISP Can Ping And Tracer But Cannot Browse
Sep 22, 2012
Router connects to ISP but cannot browse the Internet. I have updated the firmware to 2.0.3.2 and that did not work. Reset the router to factory settings and that did not work either. Router had worked until the ISP changed the ONT. The router worked initally after the ONT was changed, but that changed sometime during the day as it did not work that night. The ISP gave me a netgear router and that works, so I can connect, but I would rather the RVS4000 would work. I assume a setting at the ISP, but do not know which one. I get an error on the computer "name resolution for the name dns.msftncsi.com timed out after none of the configured DNS servers responded" I can ping, tracert and my little weather gadget works, but a web page will not display
View 7 Replies
ADVERTISEMENT
Mar 6, 2011
I'm trying to set up a network comprised of three LANs connected by serial. As this is a small part of an assignment I've been instructed to subnet into /26 and to use /30 subnets for my serial connections.At the moment I can ping between devices on each of the LANs but I can't ping between routers at all. Embarrassingly I'm not sure why, I think it may be something I've missed on setting up the serial links as I have set routers up fine before using other connection types.
View 12 Replies
View Related
Aug 22, 2011
I am able to connect to the RVS4000 remotely using QuickVPN, and can stay connected, however, once connected I cannot use the internet or see any of the remote computers via the network.
View 3 Replies
View Related
Apr 16, 2013
I have a RVS4000 and I would like to setup a Ping monitoring from the outside to a device behind RVS on lan network. I have created a rule to allow a service PING for range from WAN 46.xxx.xxx.xxx - 46.xxx.xxx.xxx to host 192.xxx.xxx.xxx but unfortunately this is not working. I can confirm that I can ping host 192.xxx.xxx.xxx from diagnostics on RVS.
View 2 Replies
View Related
Dec 17, 2011
Using the latest Cisco QuickVPN, my Windows 7, 64 bit laptop processes the QuickVPN connection to the point where the laptop attempts to ping the router and verify the connection. Those pings fail.Windows firewall is ON and IPSEC is started on the laptop. I have tried Kaspersky's firewall both enabled and disabled with no change.
View 19 Replies
View Related
Aug 5, 2011
I have a RVS4000 at one location and a second RVS4000 at home. I have established an IPSec VPN tunnel between them and it is UP. I can ping the routers from each end no problem. I can ping the IPs listed in the "Local Group Setup" and the "Remote Group Setup" from both ends no problem. I can even open up a shared resource from a Win 7 machine (e.g. by typing \10.10.10.100 in start-run from a computer on my home network).
But - i can't ping anything else on one network from the other. What gives? I need to access a 10.10.10.101 machine but can't even ping it.
- both RVS4000 boxes have latest firmware (V1.3.3.5)
- home RVS4000 setup with IP 10.10.11.1
- home network has a server with IP 10.10.11.20
- other location RVS4000 setup with IP 10.10.10.1
- other location server setup with IP 10.10.10.100
Tunnel settings on home RVS4000 (the other location properly mirror these).
- Local Security Gateway Type : IP Only
- Local Security Group Type : Subnet
[code]....
View 2 Replies
View Related
Oct 7, 2011
My flatmates and I recently got Sky broadband - their laptops connect just fine to the internet and they are able to use it without any problems. Mine also connects, but I can't do things like browse or use Skype, etc.When I go into Google Chrome, I'm told there is a DNS error that was unable to be resolved. Mozilla tells me that I have a problem with my server, and IE doesn't work either. Also, I am receiving very few packets. For every 2,000 or so packets that are sent, I only receive 2 or 6. When I click 'repair' I am told that my IP address cannot be renewed. The thing is, the internet works on my netbook at my mother's house, yet it doesn't work in my flat or other places like wifi spots.
I've tried so many things, such as clearing the DNS cache, releasing and renewing IP address, I've set the properties of the wireless connection to obtain DNS and IP automatically, I've tried pinging, I've turned off all my firewalls, I tried system restore, I've fiddled with certain keys in the registry, I even rebooted my entire hard disk last night and it still doesn't work! I'm really at my wit's end with this and I don't know what else to do. The problem is way beyond my comprehension now.
View 14 Replies
View Related
Sep 17, 2011
My MacBook works fine with my linksys router and RR internet. My wife's toshiba laptop running vista establishes a connection, but will not browse the net. My neighbor says she's having the same problem with her PC when trying to connect to my router (we live very close together).
View 3 Replies
View Related
Feb 12, 2011
My laptop is able to connect to the wireless router in my home, but the browser will never load a page, status is shown "connected". However, when I try on other laptops, they are able to surf the net. I have tried using my laptop at my friend's place with a different wireless router and it works at his place as I was able to surf the internet through my wireless! So, I've tried resetting my personal modem to factory default and it still doesn't work.
View 15 Replies
View Related
Jan 19, 2011
We've got about 15pcs at work, all on one network. All connect to one switch, and the router connects to the switch so all has internet access. Four pcs has got windows vista on, the rest XP. Yesterday I tuned on the one pc with Vista on, but could not connect to a mapped drive. I checked in the network places, i could see only three pcs, all three xp pcs. I can browse the internet, but not the pcs on my local network, and I can ping the pcs on the network.
View 1 Replies
View Related
Feb 3, 2012
I have a very strange problem affecting my LAN. New entrants to the network can ping successfuly but cannot browse. Rest of the pcs that have been on the network before are browsing quite fine. Even when I connect new PC directly to the router LAN ports, problem still persists. I've tried four different new laptops so far. I've even intalled a new router to no avail.
View 19 Replies
View Related
Feb 10, 2012
I can ping all the devices on my network but cannot browse any pc/server, mapped drives now disconnected. I can access the laptop from another machine and can browse the internet from the laptop. It has windows 7 ultimate. I have tried everything from forums, sfc/ scannow, flushdns, all services started.
View 12 Replies
View Related
Feb 6, 2011
I've been stuck with a connection problem on my desktop for 6 months and nothing I do can fix it. My computer technician friends can't fix it either, so here's my last gasp attempt to get it online before I throw the machine out of the window.I'm using XP, don't recall ever having downloaded any Service Packs, and am trying to connect wirelessly to my home network here in France. Laptops and iPhones connect no problem. I don't think it's the wireless network card (which I bought nearly 5 years ago) as I had the same connection problem in my last apartment, with the same internet provider. I eventually borrowed an ethernet cable and managed to get it working wirelessly, but I have no idea how I did it.
The computer connects to the wireless network but I can't browse or ping. I've flushed dns, tried to input the ip manually, checked and unchecked LAN settings, checked and unchecked Internet Protocol TCP/IP, i've tried winsock, I've done the netsh reset and NOTHING worksI've checked the security settings, password and encryption a hundred times, I've disabled the firewall and today I've pulled out the recovery disks It didn't.Interestingly, the desktop has suddenly decided to go online once or twice (after I'd disabled Norton) but as soon as I shut down, I'm back to square one
View 8 Replies
View Related
May 21, 2011
I just installed a new ASA 5505 for an office with three internal subnets.* The three networks can each get online fine and ping eachother, but cannot browse to shares on the two internal networks other than their own.* How do I configure the ASA to allow all traffic between these three inside networks?
192.168.152.0
192.168.152.0
192.168.154.0
[code]....
View 8 Replies
View Related
May 18, 2011
3 different browsers fail to see the internet. can ping all domains.
View 1 Replies
View Related
Nov 27, 2012
New windows 8 laptop, wired connectivity works fine, wireless connects but can't browse. Can ping ip addresses and websites dns but cannot browse.
View 5 Replies
View Related
Mar 16, 2011
two of my workstation can not receive ip address from the server but can ping server. So i can not browse with them
View 3 Replies
View Related
Jun 1, 2011
I have Aironet 1240AG and the 2 laptops connected to same SSID. Unable to can ping each other but can ping/browse server on wired.
Below are my config:
Current configuration : 2646 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname AP2!enable secret 5 $1$7EVQ$2FN7ewjcrwKCICIfmFgCO.!no
[Code].....
View 2 Replies
View Related
Feb 16, 2011
I have the above mentioned switch. I assisgned an IP address to the switch some time ago, but never had cause to use it (as it was purhcased as a spare).The problem I have now is that I cannot ping the device or browse to it via IE. Using hyperterminal and the CLI i have attempted to assign the same IP address, but i get a warning along the line of already assigned.I have set IP's to other 3COM model switches without problems. why I cannot ping this device or assist in connecting to it via IE?
View 6 Replies
View Related
Sep 6, 2012
I have a RVS4000 with client VPNs setup and have created all 5 users......trouble I run into is that when one of the users attempts to connect to the VPN from a second device (ie the sixth device to connect to the VPN), the connection does not establish....cannot ping remote server (using QuickVPN). In looking at the logs, the device that isn't working is getting a different IP (172.16 vs 192.168). I know I'm limited to 5 users, but am I limited to 5 devices as well?
View 2 Replies
View Related
Sep 19, 2012
I have a cisco 5505 and am trying to configure it with ASDM 6.4.
My vpn client connects ok to the network but I am unable to reach any of the servers.
I'm sure its a simple configuration issue as I don't have much experience with Cisco configuation.
View 5 Replies
View Related
Apr 30, 2013
I am being told from my remote end I do not have port 22 opened up. I have single port forwarding to SSH 22 and Port Range 22 enabled.
View 1 Replies
View Related
Sep 11, 2011
I have 2 internet connections in my office one via Verizon Fios and another one via the local cable company. On the fios connection I have an RV042 VPN router and on the Cable company connection I have an rvs4000 router, I would like to know if there is a way I can connect the 2 so I can share a printer I have on one of the 2 networks from the other network without using the VPN feature, like via an ethernet cable connected between the 2 and some kind of static route maybe?
View 6 Replies
View Related
Dec 16, 2012
Recently installed a WRVS4400N router on my home network. Prior to that I was using the wireless built into my FIOS router. I wanted something more secure so I went with the WRVS4400N. I turned off the FIOS wireless and am only using the cisco wireless.
Im having intermittent issues with the wireless. I have many things hooked up to my wireless including a HP printer and a Sonos system. Most of the time if I just open my ipad I cannot see anything else on my network including the printer. If I try to see the Sonos system can cannot, sometimes I can open the app on my iphone and then I can see it.
Sometimes I can see the printer and sometimes I cant. Sometimes when I do see it and then print to it, it will be gone before it even prints.
I don’t seem to have any issues thru the LAN connections.
Also, ive noticed that the wifi is much slower than the old FIOS box.
FYI, when I remove the cisco and fire back up the FIOS wifi I don’t have any problems at all at any time. And its much faster.
I have tried channel 6, 11 and auto. Also turned off IPC and still no change.
View 1 Replies
View Related
Nov 1, 2011
My network consists of the following:
Office-RV042 with static IP ->SBS2003 (10.10.10.5/ 255.255.255.0)
Remote: BEFSR41 with Dynamic -> XP sp3 VPN client (192.168.3.x/ 255.255.255.248)
Within the RV042 I have enabled the PPtP server and assigned a user. No port forwarding enabled. All VPN passthroughs and firewall is enabled. DHCP server is disabled.I can establish a connection to the rv042 and ping PCs including the sbs domain server on the office side but am unable to browse any folders. When I attempt to access a network folder located on the office server I am prompted for a username/ password. Upon entering my domain credentials I get an error stating: "the user name you typed is the same user name you logged in with. That user name has already been tried. A domain controller cannot be found to verify that user name"
View 2 Replies
View Related
Aug 15, 2011
When I ping an address from my windows machine, it succeeds, but when I ping to the same IP on my MAC OS X machine, it fails.
1. Why?
2. How to get successful ping on my MAC machine?
View 1 Replies
View Related
Mar 5, 2012
I am unable to ping any device on the internal lan from the opposite side of the tunnel. However, the tunnel connects successfully. I have the firewall disabled on both routers. Site A is using 192.168.3.1 and Site B is using 192.168.4.1. Any thoughts on why I cant ping one router from the other?
View 4 Replies
View Related
Apr 20, 2013
Ive set up a rvs4000 with two vlans, one as a bussiness network and the other as a guest network. Everything works fine and the networks can not see each other. I would like to add wifi and I would like to do so with keeping both networks separate. I have a used 1130AG access point and was wondering if I could use this single AP for both networks. If so, how would I go about doing so? Is there a better suited AP for my needs?
View 4 Replies
View Related
May 16, 2012
I have an RVS4000 running V2.0.2.7 firmware that gives me an "Invalid Character(s) Found" error message when I try to edit an existing ACL.
I'm trying to deploy 57 of these routers and would like to be able to use a pre-built config dropped onto each router.
I initially planned on editing the exported config with a find&replace for my local LAN addresses. Since that didn't work the next reasonable solution would be to edit the ACL list (much more tedious, but still better than hand-entering every ACL on all 57 devices).
when this bug will be addressed? Alternatively, if there is an offline configuration editing tool I would be one happy camper to have it!
View 2 Replies
View Related
Jun 3, 2013
I have an RVS4000, not installed. How can I tell from the unit or the packaging that it is a v1 or a v2, without installing and switching it on (which I don't want to do now) ? Are v1 branded Linsys and v2 Cisco ? Can you tell from the date on the package (mine says copyright 2011) ?
View 1 Replies
View Related
Sep 4, 2011
I don't know if my vendor mislead me, but I need to do this: There is a public subnet in my office, not a 192.168.x.x, but a real Public IP.The reason is that we do VOIP and those are only servers. I installed a RVS 4000 in that location, and assigned a PUBLIC Ip to BOTH the WAN and LAN, since when I connect from outside, using either QickVPN or another identical router, I need to be assigned one of the PUBLIC Ip's on the remote LAN. That is the whole idea of the project, to locate servers remotely and make them use our set of PUBLIC IP's. Well, so far I cannot connect either with the Quick VPN client, or using the VPN Wizard. It goes and creates the tunnel, without error, but when I click test, it fails.
View 2 Replies
View Related
Mar 15, 2012
We have backup and other traffic over our vpn which is affecting our ip phone service between two sites. Our consultant suggested implementing QOS over the VPN to give the phone traffic priority. Is this possible with the rvs4000. Is there any good source saying how to do it. Is the setup of the QOS on this router similar to another router where this has been discussed.
View 1 Replies
View Related
Mar 19, 2012
I have problem with bandwidth management on my RVS4000.
That is the way how i done it:
All traffic (TCP & UDP on all ports)
IP range 192.168.0.2 - 192.168.0.2 (My IP adress)
Guaranted download speed 1kbps
Maximum download speed 5000kbps
after saving setting and rebooting router I have maximum download speed on my PC 12000kbps, Why QOS doesnt work ?
View 3 Replies
View Related
