Two Routers One Network And Cannot See Other Computers
Mar 29, 2011Need the solution for aboove
View 19 Replies
ADVERTISEMENT
Cisco Routers :: RV120W - Can't Map Win7 Network Computers Over VPN
Oct 9, 2011I have installed an RV120W router specifically for the VPN capability. I have a small home office with 3 Win7 computers and a SeaGate GoFlex Home NAS drive opperating on the RV120W LAN. I need to allow users to access these networked computers and NAS device over the VPN by mapping their IP locations, such as 192.168.100.155, which is the local IP assigned by the router.
I am able to establish a QuickVPN connection without trouble. I had to set the port to 60443 as it was conflicting with the NAS drive, but this resolved that problem.
I am able to ping the router without any problem over the VPN using the local IP address. I am able to pull up the NAS web portal off the drive via the local IP address using a broswer. Therefore, I know I am talking to the drive via port 443 (I think that is the right port for http). I CANNOT ping the NAS drive over the VPN. I CANNOT ping ANY of the computers or the NAS over the VPN.
Through my reading it appears that a port is being blocked that might need to be opened. But, in the same readings, they say you should use a VPN so that you don't have any issues with blocked ports. I thought I was using a VPN!
I am testing the VPN on a WIN7 Pro laptop with the most current QuickVPN installed. I have also update the firmware on the router to the most current as well.
When I do an ipconfig /all command and look at what I think is the VPN information, there does not appear to be any tunnels established. I don't know if this matters, but thought it odd since I do have a VPN established.
I have enabled PING in the firewall and unchecked the Block Fragment Packets.
I should also note that I can remote manage the router using the 60443 port and an https connection to the local ip address, so clearing there is a connection. SO WHY CAN"T I SEE ANY OF MY WIN 7 COMPUTERS OR MY NAS DRIVE?
I have burned a lot of time on this and without the VPN capabilities, this router does me not good.
Cisco Routers :: RVS4000 - Browsing Remote Network Computers?
Feb 24, 2010I have recently bought RVS4000 and I'm having problems with remote network computers. I can only access them by IP, by name it always fails. Localy I have BEFSX41, remotely RVS 4000, connected throught VPN. Everything else is working fine.
View 6 Replies View RelatedRouters / Switches :: Connect 3 Computers Using LAN?
Dec 26, 2011I'm having trouble trying to connect 3 computers via LAN for gaming using straight Ethernet cables and a net gear router. Only 2 computers seem to connect at a time. All 3 can connect to one another (one at a time) and the I.P. addresses have been set to 192.168.0.1 , 192.168.0.2 and 192.168.0.3. The cables work fine and the computers, but I'm wondering if I'm using the wrong kind of hub/router?
View 3 Replies View RelatedHome Network :: Setup A Local Network Between The 3 Computers But Separated?
Jun 28, 2012i'm connected to the internet through a shared internet connection through a switch,and also have 3 computers connected to the same switch,what i want to setup a local network between the 3 computers but separated from the internet network?
View 6 Replies View RelatedRouters / Switches :: Possible To Connect Two Computers With 2 Different IP Addresses From Same ISP
Aug 3, 2011I am having 2 Pc's and 1 ISP. I am havng a DSl modem cum router. Is it possible to connect two computers with 2 different ip addresses from same ISP? My ip address is a static one btw..
View 3 Replies View RelatedRouters / Switches :: How To Set Server 2008 R2 On A Lan Of 12 Computers
Jan 17, 2011We need internet connectivity on all workstations
View 1 Replies View RelatedRouters / Switches :: Connect Two Computers To 2 Printers?
Feb 16, 2011One computer is an iMac running Snow leopard and the other is running Win 7. I wish to switch either computer to any of the two printers.
View 1 Replies View RelatedBelkin Routers :: No Response From N300 On Other Computers?
Dec 27, 2012Cannot get wireless from any computers in home or room even the computer that I have installed the Belkin N300 on. When I click on the Belkin Icon on task bar get message "Wireless hardware not found" followed by comments about wireless radio not turned on and then how to recognize it with wireless radio icons. Now what do I do?
View 1 Replies View RelatedRouters / Switches :: Why Can't Ping Computers On Separates Subnets
May 21, 2012My new employer has asked me to determine any issues that could be causing performance issues our LAN. The network has two subnets and one of the first things that I noticed is that I cannot ping computers on subnet A from subnet B. I've looked into this and found a few things.-I CANNOT traceroute to computers on subnet B from subnet A-I CAN NMAP to computers on subnet B from subnet A-Computers on subnet A CAN ping other computers on subnet A and computers on subnet B CAN ping other computers on subnet B-Computers on subnet A CAN ping and access servers on subnet BI am relatively new to networking and not exactly sure where to start investigating this problem.
View 9 Replies View RelatedRouters / Switches :: Ethernet Router Only Allowing Two Computers?
Jun 12, 2011I recently got a new Toshiba laptop, which works perfectly. We already have an HP desktop PC as well as a Dell laptop, which are both connected to an Ethernet router. When I got my Toshiba, I couldn't connect to the router, whether from a new Internet cable, the cable the Dell uses, or the cable the HP uses (it works perfectly fine with Wifi). The next day I got up early and tried again, and it worked. The HP was turned on, and it connected. But then the Dell wouldn't. Over the next couple days, we realized the problem was that the router only allowed the first two computers that were connected to it to connect to the Internet, but not the third one. The router itself allows eight cables to be plugged into it at a time, so I don't see why it's only allowing two computers, whether laptop or desktop, to connect. Is there a possible solution to this?It's an 8-Port Workgroup Switch, Model EZXS88W.Also, our router DOES NOT support Wifi
View 1 Replies View RelatedBelkin Routers :: F5D7234-4V5 Need Software To Change Computers
May 29, 2013I am moving my wireles router to a new computer (Belkin F5D7234-4V5Do i need software for it to work on my new computer and if so can I get it online.I can't find a software disc.
View 1 Replies View RelatedCisco Routers :: RV042G - Can't Seem To Be Sharing Names Of Other Computers On Net
Apr 13, 2013I've just installed a RV042G router for the first time. The computers connect to the internet just fine, but they can no longer see each other through the Windows workgroup. I can ping the router, but not other computers on the net. The router doesn't seem to be sharing the names of the other computers on the net.
View 1 Replies View RelatedRouters / Switches :: How To Share Usb Based Internet One PC To Local LAN Computers
Mar 22, 20134 pcs are connected to a adsl bb router having 4 lan ports. i have removed the adsl cable going to the bb router cos bb giving problems. i m then connecting to internet on any one pc using a tata photon usb device. i want to share this internet on other 3 pcs. those 3 pcs are getting their ips from the bb router in 192.168.1.x series. all pcs are pinging to gateway ie 192.168.1.1 but not pinging each other. why?
View 3 Replies View RelatedCisco Routers :: RV042 - Unable To Forward Rdp Connections To Computers
Feb 25, 2013We have a Cisco RV042 Router. Two ISP's and using dual wan setup. We are trying to connect to a pc on our network using rdp. The pc we are trying to connect to has been configured to listed for rdp on port 3390. I have tested it internally and connect via rdp thru said port.
I have setup a port forward rule on the router to forward port 3390 to the ip of the pc. I have setup protocol binding for port 3390 service on wan1.
Belkin Routers :: 300N - Access WAN Via Wireless While Firewall Wired Computers?
Dec 15, 2012The facility provides WiFi access. I'd like to configure his router to access the facility's WiFi, as WAN access to the internet while providing DHCP service to the wired ports. The idea is to use the 4 wired ports to provide inter-connectivity to each other and internet access via the router's wireless connection via wireless for internet access by the wired client machines.I'd also like to firewall the wired devices from access by other users of the facility Wireless network.Can I do that? How do I configure the wireless aspect of their Belkin Share 300N? What other settings do I have to set.
View 2 Replies View RelatedXp Cannot See Other Computers On Network?
Jun 11, 2011I have an XP machine that is unable to see any other computer on the network. I disabled the firewall and I can ping any device on the network with no issue. I have set several other computers to the same workgroup which is mshome. Lastly I have read several other post and tried the ideas there including this one...Finally, let's do the stack repair.TCP/IP stack repair options for use with Windows XP with SP2.
Start, ]R[/B]un, CMD to open a command prompt:
In the command prompt window that opens, type type the following commands:
Note: Type only the text in bold for the following commands.
Reset TCP/IP stack to installation defaults, type: netsh int ip reset reset.log
Reset WINSOCK entries to installation defaults, type: netsh winsock reset catalog
Reboot the machine.That did not seem to work. As I am still in the same situation.
another note. This is the only XP on the network. Everyone else is Windows 7. Also on a side note, the reason I am doing this is to install a printer on this one and allow the other computers to print from it and seeing folders is good also.
Windows IP Configuration
Host Name . . . . . . . . . . . . : Upstairs
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Unknown[code].....
Can't See Other Computers On The Same Network
Oct 7, 2011I have a wireless router which works just fine. I can connect my laptop as well as my iPad to it. I also have a hard wire connection that goes to my computer which works just fine. how can I get my computer to see the other computers in the network? They just don't show up even though I have shared enabled. There is only one router, so I thought it might be automatic, but it doesn't seem to be.
View 2 Replies View RelatedCan't See 2 Computers On The Same Network
Aug 8, 2011I have two identical computers on the same home network (and a couple of others too). My problem is the even though they are connected to the same wireless router and can each see the internet and the printer that online they cannot see each other. When I ping one from the other I get no response though they both receive responses from the router. I can't transfer files etc. It works a while ago but can't seem to get them connected again.
View 9 Replies View RelatedNetwork Computers Disappear
Aug 4, 2011I have a vista, an xp, and a win7 computer networked. The xp is very temperamnetal, in that it randomly is accessible and just as randomly disappears. i often get the message "Computer (name) is not assessible...." The trouble is most acute in trying to access the xp machine from the win7.
View 4 Replies View RelatedCannot Access Network Computers With Ip / Sometimes With Name
Feb 26, 2012I usually access my network computers by typing "\ipaddress" in run command. But sometimes this doesn't work so I have to type the computer name to access it. Similarly, sometimes i could not access with name but could access with ip.
View 7 Replies View RelatedServers :: How To See Computers In Network
Jan 25, 2011I have a 2008 domain with win7 computers and winxp clients, i am able to see the win7 clients but not the winxp nor the servers in the network neighbourhood, ping works fineI can browse through a system on the network, but unable to have a broad view of the computers
View 1 Replies View RelatedConnect 20 Computers In A Network?
Oct 10, 2012how to connect 20 computers in a network[/u][/i][/b]
View 1 Replies View RelatedSeeing Other Network Computers With Windows 7?
May 3, 2011My home network was made up of a desktop running windows XP home (wired) and a desktop also running XP (wireless). I have recently added a desktop running Windows 7 (wireless) to the system. When I turn on the Windows 7 machine, it sees the other two machines and I use the files from them easily. But after the new machine has been on awhile, it does not see the other computers. (I can, however, still access the shared files on it (the Windows 7 machine) from the other desktop (haven't checked the laptop). If I power down the Windows 7 and then turn it back on, the other machines show up immediately. I've got them all named to the same workgroup and in the network settings in the control panel, I think that it is set to discover the network.
View 4 Replies View RelatedAccessing Network Computers LAN
Jun 1, 2011I have 2 computers connected in a LAN. I want to access the other computer through the main one.I do have shared folders (homegroup), but I would like to know how I can get complete access to the other computer via command prompt maybe?
View 4 Replies View RelatedHow To Intentionally Cause Lag To Certain Computers On Network
Mar 8, 2011How would I force lag to certain computer(s) on the network? Even better would be to only make certain processes lag. Would closing a port completely restricted traffic through it? How about limiting it? I have DD-WRT firmware installed on my Linksys router. This is my network that I pay for, so i am allowed to do it.I could possibly limit a port that online games would use specifically, or just set a low bandwidth cap for the IP the computer is on?
View 9 Replies View RelatedCan't Find WEP Key To Get Computers On Network
Dec 16, 2012I have vista and a lynksys but cannot find my key to get other computers on the network
View 6 Replies View RelatedCannot Connect To Other Computers On Network?
Dec 5, 2012I have a Windows 8 Pro laptop, and a new Windows 7 Laptop. When I try to setup the connection so that I can share files and folders between the two computers, I am asked for the User name and the password. I see the password in the homegroup, but entering it does nWhat is the user name in this case? My computer name or the other computer name or something else
View 1 Replies View RelatedHow To Connect 4 Computers On Network
Nov 15, 2011How to connect 4 pc on network.
View 1 Replies View RelatedHow To Retrieve Computers Network Key
Oct 8, 2012how to retrieve my computers network key?
View 1 Replies View RelatedHow To Network More Than 10 Computers On One Server
Jul 12, 2012How do I connect more than 10 computers on one server?
View 1 Replies View RelatedSet Up Ethernet Network With 2 Computers?
Sep 14, 2011i have modem with an rj 45 hub. i now have a switch with four hubs when i connect for my two computers , only one of the computers could connect to the internet
View 2 Replies View RelatedOne Way Connection Only Between Two Computers On Network
Mar 18, 2011I am able to go in only one direction between the two computers on my Network. The Acer Netbook computer can access the Toshiba Laptop, but the reverse is not possible. Both computers run Windows Vista Basic and Windows Firewall. I can ping the Acer from the Toshiba, but when I try to copy a file it says I do not have permission.
View 1 Replies View Related
