Cisco Routers :: RV042 / Responses From Other Devices On Network Delayed
Nov 15, 2011
I keep getting an error when trying to use the Microsoft Link layer Topology discovery. It claims there the is either network delays or an incompatible router on the network.
Actual error:
"Responses from other devices on the network are delayed or there is an incompatible router on the network"
I have 2 RV042 routers, one for each of our network connections. So I am assuming this is the source of the error.
View 3 Replies
ADVERTISEMENT
Mar 28, 2013
On the System Summary screen in the Port Statistics table when you click on one of the Connected links the pop open window does not show the IP address of the connected device when using IPv4. Where can I find this?
If the devices are using static IP addresses and not getting them from the DHCP server they do not show in the Client Table under DHCP Status.
If they are know MAC addreses because they have been assigned to static IPs on the DHCP setup screen they will not show up in the Uknown MAC Addresses pop up window.
View 1 Replies
View Related
Jan 13, 2013
I recently reinstalled windows so as my pc was on service (one of rams was gone down) , but it is not the issue. My network connection is delayed, sometimes 5 minutes, this time 15.I found 2 types of errors in event log, I will add them at end of post .
So the problem - my computer acces network really slow. I am musing Modem what is connected with PC by my Ethernet cable and on pc I am using Local Area connection.Computer simply say that cable is unplugged while it is pluged in ( It works perfect with same modem and cable onmy laptop, I even tried different cable - no refult).Icon all the time have red cross, sometimes disabling/enabling network adapter fixes i, but nit today, then after some time it turns on in normal speed - several seconds blue circle spinning around and then connects.
But there is huge delay.Usually if he turn in it stay like thus, but sometimes it disconnects after some time ( after hour, maybe less or more ).I recendly find out one more thing, if I have my net fully working on my laptop and I plug off cable from laptop and blug in into my stacionary PC it connects pretty fast, i may be nothing, but sometimes it is only way.When trying connect it drops these 2 errors, sometimes several times : The driver DriverRTL8167 failed to load for the device
PCIVEN_10EC&DEV_8168&SUBSYS_E0001458&REV_014&39aeacf1&0&00E5.
Your computer was not assigned an address from the network (by the DHCP Server) for the Network Card with network address 0x001FD08E0204.
View 1 Replies
View Related
May 31, 2012
In the company that I'm currently working, we have one gateway with LAN IP address 172.16.0.1 and netmask /23 [=255.255.254.0]. In this gateway, there's a DHCP server providing 510 IP addresses in its pool.
I need to substitute the server, replacing it with a RV042. This afternoon, when I was configuring this router, I noticed that it doesn't let you configure different netmasks, since it comes with some of them predefined [starting in 255.255.255.0 and so on], as shown in the picture below:
I need to provide DHCP for this /23 network, but it seems that DHCP field cannot assign /23 networks.
View 4 Replies
View Related
Nov 1, 2011
My network consists of the following:
Office-RV042 with static IP ->SBS2003 (10.10.10.5/ 255.255.255.0)
Remote: BEFSR41 with Dynamic -> XP sp3 VPN client (192.168.3.x/ 255.255.255.248)
Within the RV042 I have enabled the PPtP server and assigned a user. No port forwarding enabled. All VPN passthroughs and firewall is enabled. DHCP server is disabled.I can establish a connection to the rv042 and ping PCs including the sbs domain server on the office side but am unable to browse any folders. When I attempt to access a network folder located on the office server I am prompted for a username/ password. Upon entering my domain credentials I get an error stating: "the user name you typed is the same user name you logged in with. That user name has already been tried. A domain controller cannot be found to verify that user name"
View 2 Replies
View Related
Jul 14, 2012
I am having difficulty with gateway to gateway vpn on RV042.I have site A and site B, both have static IP address,local IP at site A is 192.168.1.0 local IP at site B is 192.168.5.0I have configured each site as directed in the documentation, the sites connect ok within the admin consoles, I cannot browse any resources from either site. Site A is a domain.local and I am part of that domain at site B. I can ping site B local address from site A and vice versa however I can not ping any of the servers or NAS devices on either network. the only device I can ping successfully inside the network is a phone server (splicecom unit).
I have read various posts in the discussion boards but have found no resolve. Internet access is fine from either site. I think that it could possibly be a DNS issue but am unsure, should I add DNS entries in the advanced section, if so what DNS would I enter?
View 5 Replies
View Related
Nov 15, 2012
I used to have the problem where QuickVPN keeps on trying to verify the network because the RV042 cannot get the final ping to the client.I then bought a RV042 HW version 3 on the VPN side and I installed RV042's at the clients as well.This may look like overkill but believe me, it gives peace of mind, it made things a whole lot better, everybody happy.I am going to set up tunnels but for the time being the clients use QuickVPN. The above setup is all good if people access the vpn from the same source.
I now have a problem where one of our people is in Vietnam and she cannot access the vpn due to the "verifying network" loop.Looking at the log everything looks great, I compared a successful connect with an unsuccessful one and the logs are identical.The only difference is that the final ping is blocked (recorded in the QuickVPN log on the client side).The client uses W7 with firewall on.No need to repeat suggestions, such as turing printer sharing off, I have been through all that. isn't this simply caused by the ISP in Vietnam blocking pings ?
View 2 Replies
View Related
Dec 30, 2011
I am able to make a connect to my remote RV082, I can ping the inside network gateway from the remote end but I cannot ping or get to any devices on the remote network, my local network is 192.168.15.x and the remote network is 192.168.0.x I am using WIN 7, and using the native VPN setup in WIN 7, I do a print route and everything looks fine there, I can't figure this out
View 8 Replies
View Related
Sep 13, 2011
I configured ASA5520 and RV042 for site-to-site IPSec VPN tunnel.Tunnel get connected, but no ping, no traffic between both end network.
Network:
=======
192.168.113.0/24----------192.168.113.6 -ASA--------public, static IP address------Cisco 2821--------Internet
192.168.10.0/24-----------192.168.10.1 -RV042-----public, static IP address------Cisco 2821--------Internet
ASA5520 config:
----------------------
name 192.168.10.0 VPN
!
interface GigabitEthernet0/1
nameif NET
security-level 100
ip address 192.168.113.6 255.255.255.0
[code]....
View 5 Replies
View Related
Nov 26, 2011
I have an RV042 using Quick VPN to connect to a remote network. I have port 1723 forwarded to a static IP address on a Windows 7 Pro 64 bit PC. I can establish the VPN and ping a printer but not the Win 7 PC. I can not acccess any shares on the pc via the IP address. It has Norton Antivirus and Windows Firewall. This remote PC replaced a Windows xp PC that allowed access to the shares. I have tried access with a Windows XP Pro and Windows Vista Home Premium PC. Neither have worked.
View 1 Replies
View Related
Nov 2, 2011
I have a RV042 using (for now), just the single WAN interface. I am trying to forward all packets to port 9000 from the WAN to a single IP address on the network. I've set up both forwarding rules under Setup -> Forwarding and under the Firewall -> Access Rules.I cannot connect to my device from the outside world, however. Is there something I'm missing?
View 4 Replies
View Related
Feb 14, 2012
I have recently installed a new Cisco SG 300-10 switch--running in layer 3 mode--to function as a basic router for a new subnet installed at one of my company sites. When we attempt to ping devices on the 15.120.204.0 subnet from the 230.20.1.0 subnet, each device gives 2 responses and then times out continuously after that. If we wait long enough (thus far, an undetermined period of time) and reattempt to ping the same devices, the same thing occurs. Otherwise, we get nothing but timeouts. This occurs regardless of where we connect in the 230.20.1.0 subnet including VLAN1 on the SG 300-10. However, if we connect into VLAN 2 on the switch and assign a static IP, those same devices respond continuously. I was thinking that this must be a security setting of some kind but I'm unable to locate anything in the SG 300-10 that would appear to cause this.
View 1 Replies
View Related
May 8, 2013
After some wireshark, I see that when I have a vLan on the switch, only win7 gets IP, my macbook doesn't, sniffing to the bootp, I see that the DHCP sends NAK and after I only have DISCOVER & OFFER...
When I get the same switch and the same router and take out the vLan on the switch, everybody get an IP. What's the deal with this switch and vLans and Mac OS x ? Do I have to setup something else ?
View 1 Replies
View Related
Jan 26, 2012
We have a Cyberoam CR15wi hardware firewall at my company and it seems to be interfering with FTP to our website. I won't go into precise details but Filezilla, Dreamweaver 5.5, and GoLive CS's FTP utilities all will put a file up onto our web hosting company's server then indicate that the server didn't send a response so it assumes the file never got there. The file does in fact get uploaded intact though so it seems the server's response itself is the thing that's getting blocked. This problem occured with two different web hosts and FTP works perfectly with the same software and same FTP settings from my home connection so it's definitely us.
View 6 Replies
View Related
Jul 11, 2011
I have a newish instance of 5520 running. I am seeing some odd logging issues in that the logs are significantly delayed showing up in the real time viewer. I'll try to connect, say on remote desktop, and will not see the traffic in the viewer for up to 20 seconds or so after I'm already connected to the server. I have not seen this before.
View 1 Replies
View Related
Dec 5, 2012
I am currently testing Netflow accuracy on my Solarwinds platform. So I have been transferring a large file across an ASA 5520, which is set up to send Netflow data to out Solarwinds server.
The problem is that the Netflow data does not show up on Solarwinds for about 2.5 hours. Once it gets there the size is correct, but the time stamp on Solarwinds is 2.5 hours behind when the transfer happened. For routers it is showing up within a few minutes.
ASA is running 8.2(5) and Solarwinds NTA 3.9.0. Firewall and Solarwinds times / timezones are the same.
View 8 Replies
View Related
May 31, 2012
I am seeing SNMP coldstart traps that either are delayed by many hours or are false (e.g. right after receiving the coldstart trap a query to sysUptime shows the nodes been up for days).I seen this twice this week in a new network environment for me for two different C2900s running C2900-UNIVERSALK9-M Version 15.0(1)M3 Assuming the coldstart traps are coming from the actual source nodes, I am curious what could be going on here.
1) One guess I have is possibly the system clock changed could cause the SNMP agent to send a false cold start trap. Then my guess is in the device log I should see a system time change syslog message.
2) I recall hearing once that syslog and possible traps messages are held in configurable buffer who default value is 1 and if not sent are held and then suffer a delayed sent. Is it true for both traps and syslog ? In the past I assumed this was simply the logging history buffer and applicable to syslog traps only. My assumption in the past was that last trap or last syslog message is sometimes held on reload and sent immediately after restart regardless of device connectivity to the management target.
I always assumed coldstart traps are never delayed for any reason and that they were pretty accurate substitutes for system reload syslog messages. Does anyknow know any reason for false or delayed coldstart traps on a C2900 with IOS 15.0(1) ?
View 1 Replies
View Related
Dec 9, 2012
I'm trying to get a Curl Response from an outside server, however I noticed I cant neither PING the server in question nor connect to it.I tried disabling the iptables firewall but I had no success.My server is running behind a Cisco Linksys WRTN310N Router with the DD-wrt firmware Installed. In which I already disabled the firewall.
Here are my network settings:
Ifconfig
eth0 Link encap:Ethernet HWaddr 00:26:b9:76:73:6b
inet addr:192.168.1.120 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::226:b9ff:fe76:736b/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[code]......
This gets an empty result array. This function however works well in the previous server where the script was hosted before. No modifications where made whatsoever
View 4 Replies
View Related
Jan 24, 2013
I have RV042 and E4200 routers . I tried the manual UPnP port forwarding using Rv042 router and was succesful ( by typing 192.168.1.1 in the explorer and logged in using user name and password )
I am using a linux embedded system whose Internal IP ,Internal port are mapped .This system is connected to one of the LAN ports
I want to try auto UPnP port forwarding both for RV042 router and Linksys E4200 routers
After enabling the Upnp option only and logging out ,Can i add a port mapping entry in this router without logging in using a C++ program which runs on linux embedded system .
View 2 Replies
View Related
Aug 22, 2012
I was looking for a small business router that has VPN support and dual WAN support for load balancing. Upon reading reviews, I think RV042/RV042G is a good choice. Now am thinking if it supports intervlan/ router-on-a-stick configuration?
View 5 Replies
View Related
Feb 27, 2012
I have two Internet connections-
1-DSL Modem (WAN1-Internet Port)
2-Cable Modem-Comcast (WAN2-DMZ/Internet Port)
I connected the DSL (WAN1-Internet) port in and the Cisco RV042 was able to get an IP automatically. I tested the connection and it works just fine. Then I connect the Cable Modem-Comcast (WAN2-DMZ/Internet Port) in and I have the RV042 automatically optain IP address. But it just says 0.0.0.0. I've tried release/renew and that does nothing. Also, when I connect the 2nd Internet connection the Internet goes down. The only way it goes back up is when I disable under the PORT MANAGMENT setting.
All the settings have been kept to the default.How can I get the router to obtain an IP address from the Cable Modem-Comcast (WAN2 DMZ/Internet Port).
View 5 Replies
View Related
Mar 6, 2012
We have an Cisco RV042. We need to setup a VPN with a business partner who is already using our current IP scheme on another VPN with another client. They have asked us to NAT our IP's from 192.168.25.x to 192.168.245.x
I can't seem to figure this out on this router. I have done it on a Sonicwall and Watchguard, but can't seem to get it to work on the RV042.
I have setup the VPN and the One-To-One NAT. The tunnel will connect (using the 245.x IP as our local IP on the VPN setup), but no traffic will pass through.
View 1 Replies
View Related
May 20, 2012
i was planed to make a vpn over rv042 so i get the rv042 connected behind a thosmon 456(configured as a bridge) and 1 static ip ... and i configured the vpn and worked great ...but due to some circumstance i get a package of 6 ips insted of the old ip , so when i try to configure the router with the ISP they but the wan ip 10.232.x.x and told me that an internal ip from there lan ... and give me the 6 ip of 196.x.x.x to use as 1 for internal interface for the rv042 and 5 for the pc's,now the vpn not working anymore...notice: when try to configure the vpn tunnle in the local securty setting i mark the ip only and the ip that abear is the wan ip 10.232.x.x but i can't ping that ip beside i can ping the internal ip of the router 196.x.x.50does rv042 can support static and virtual ip inside the lan |! can i configure the thomson as pppoe and use one static ip from 196.x.x.x as wan ip for it ... and use anther 196.x.x.x ip for the rv042 to get access from outside and connect the lan to the rv042 with internal ip 192.168.x.x ...so i can access the vpn from outside .....and can connect the device i need to use static ip to the thomson ...
View 0 Replies
View Related
Sep 23, 2011
Firmware v4.0.4.02 has a nasty bug in the VPN section. If you switch to "IP by DNS Resolved" (yes, it says "Resolved" instead of "Resolution". Gotta love all the Engrish in the RV042!), it will automatically populate the field with "@yourdomain.com". This will cause the VPN to not lookup the proper IP address. Simply deleting the atmark after it populates will fix the problem.
Let's see what happens when we validate a Cisco RV042 webpage:
Errors found while checking this document as HTML 4.01 Transitional!
Result: 353 Errors, 1 warning(s)
Don't even get me started on the horrible Javascript...
View 0 Replies
View Related
Apr 24, 2013
i am trying to make a simple Site to SiteVPN between two offices, one has Cisco ASA and one has RV042 router.when traffic initiated from ASA side, i keep getting this message in Debug and tunnel wont come up
.
[IKEv1]: Group = A.A.A.139, IP = A.A.A.139, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.Apr 26 00:15:53 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
whereas if traffic initiated from RV042 side, i keep getting this message in debug and tunnel wont come up.
Apr 26 00:43:44 [IKEv1 DEBUG]: IP = RV.RV.RV.139, Oakley proposal is acceptableApr 26 00:43:44 [IKEv1 DEBUG]: IP = RV.RV.RV.139, IKE SA Proposal # 1, Transform # 0 acceptable Matches global IKE entry # 6Apr 26 00:43:44 [IKEv1]: IP = RV.RV.RV.139, Connection landed on tunnel_group RV.RV.RV.139Apr 26 00:43:45 [IKEv1]: IP = RV.RV.RV.139, Connection landed on tunnel_group RV.RV.RV.139Apr 26 00:43:45 [IKEv1]: Group = RV.RV.RV.139, IP = RV.RV.RV.139, Freeing previously allocated memory for authorization-dn-attributesApr 26 00:43:45 [IKEv1]: Group = RV.RV.RV.139, IP = RV.RV.RV.139, PHASE 1 COMPLETEDApr 26 00:43:45 [IKEv1]: IP =RV.RV.RV.139, Keep-alive type for this connection: DPDApr 26 00:43:45 [IKEv1 DEBUG]: Group =
[code].....
View 1 Replies
View Related
Sep 27, 2012
Apparently one of my two ISPs,CenturyLink, supports 6rd connections to IPv6.
This is supported natively on my Q1000 ActionTec modem, however my modem is in "transparent bridging" mode, so that the RV042 v3 can be the only router.
how to configure the RV042 to operate in this manner.
Per the CenturyLink FAQ: the IPv6 address space is:
2602::0 /24
Most importantly, can I do this WITHOUT buying a new modem.
View 2 Replies
View Related
Aug 28, 2011
I have a RV042 router (Ser#: NKS10462300, HW V3) running Firmware version v4.0.2.08-tm (Jan 14 2011 22:08:38) set up as a gateway. Right after it boots I am able to long into its web interface but shortly after that if I try to log into it I go through a very log time out while the web page is waiting the router to respond and then eventually IE comes back and says it 'cannot display the web [age'.
View 30 Replies
View Related
Jan 14, 2013
I have a Cisco RV042 VPN Router and I have added a group vpn, but when I am trying to connect I got an error that the remote vpn server isn't responding.
Here's my log:
2013/01/15 12:24:53 [STATUS]OS Version: Windows 7
2013/01/15 12:24:53 [STATUS]Windows Firewall Domain Profile Settings: ON
2013/01/15 12:24:53 [STATUS]Windows Firewall Private Profile Settings: OFF
2013/01/15 12:24:53 [STATUS]Windows Firewall Private Profile Settings: OFF
2013/01/15 12:24:53 [STATUS]One network interface detected with IP address MY HOME IP
[code]....
If I am trying to connect the status of the vpn user in the remote interface is "online".I have deactived my firewall at home and at the server for testing purposes.
View 2 Replies
View Related
Apr 19, 2012
I am looking to configure RV042 for VPN access to local machines and Win 2008 server. The story: Had issues with remote printers being created for clients logging into old Linksys RV042 with Linksys VPN software. First Tech exposed server without security, and it had to be removed as it was being attacked, but did not fix printing issue. 2nd tech could not get VPN to work after 1st tech. 3rd tech, 4hours, and I got that the router is a piece of ... So I'm out over 1000, and not able to have a simple router set up. The present situation. New RV042 with firmware V4.1.1.01, using Cisco VPN client 5.0.07.0410, most XP 32 bit machines coming into network, one 64 bit win 7. My clients have been unable to access their data for too long.
View 3 Replies
View Related
Feb 6, 2012
Is there any documentation out there on a step-by-step instructions on setting up a vpn on a RV042 router?
View 1 Replies
View Related
Apr 30, 2012
I'm trying to set up 2 subnet with two RV042 routers. One router will act as a gateway and both WAN ports will be used by two different isp connection. The first router (gateway) LAN IP will be 192.168.0.1/24. I would also like to set up another router behind the gateway with with separate subnet 192.168.1.X/24. And I would like clients on the 192.168.1.x subnet to use the internet through the gateway router and clients on the 192.168.0.x subnet to access resources on the 192.168.1.x subnet. Am I able to do this with two RV042?
View 6 Replies
View Related
Sep 2, 2012
The issue is when I am using PPTP the router seems to die, not every time but I would say about once a week now. I am the only PPTP user, simply using RDP. A few hours into an RDP session the PPTP connection drops and cannot be re-established, or quickvpn, nothing. Routing still works (somewhat, high latency) locally.
When I've checked the logs both times I see:
TimeEvent-TypeMessageSep 3 17:07:56 2012KernelOut of memory: Killed process 14354 (pppd). Sep 3 17:07:56 2012KernelOut of Memory: Kill process 14354 (pppd) score 177 and children. Sep 3 17:07:56 2012KernelOut of memory: Killed process 14367 (sh). Sep 3 17:07:56 2012KernelOut of Memory: Kill process 14354 (pppd) score 234 and children. Sep 3 16:46:41 2012KernelOut of memory: Killed process 14330 (pppd). Sep 3 16:46:41 2012KernelOut of Memory: Kill process 14329 (pptpctrl) score 134 and children. Sep 3 16:46:41 2012KernelOut of memory: Killed process 14324 (pppd). Sep 3 16:46:41 2012KernelOut of Memory: Kill process 14324 (pppd) score 177 and children. Sep 3 16:46:40 2012KernelOut of memory: Killed process 14328 (sh). Sep 3 16:46:40 2012KernelOut of Memory: Kill process 14324 (pppd) score 234 and children. Sep 3 15:36:15 2012KernelOut of memory: Killed process 14187 (pppd). Sep 3
[code]....
View 3 Replies
View Related
Nov 11, 2012
I have an RV042 connected via VPN to the office (to a LinkSys DFL-700). Sometimes the VPN is dropped and never activates again. In this state, if I try to connect to the WEB interface, I can log in, but the router hangs at the login screen. I have to power recycle the router to make it work again.
Updated to latest firmware 4.2.1.02 for V3 hardware. The funny thing is that services from the WEB routed through to local IP adresses on the lan is still accessible. I have setup PPPT VPN on the router, and that also fails to work.
Is there, as a workaround, any possibility to access the routers reset page or access via TELNET to reset the router? This migth be useful, when I'm out. (I have a backup solution to access the local network at home).
View 3 Replies
View Related
