I bougth a used ASA 5505 on ebay which is experiencing this problem [url]... LEVELS or at least the described problem, if i touch the appliance while it is running it will somtimes go to this non working state as well
View 11 RepliesFirmware asa805-k8 was installed and saved on an ASA5505. Upon power failure the ASA5505 reverts to an older firmware, asa724-k8. 1) Is it normal for ASA5505's to revert to older version upon power failure. 2) ASDM/web browser doesn't work using IE--username and password brings to empty screen. how to revert back to later image.
"
# sh ver
Cisco Adaptive Security Appliance Software Version 7.2(4)
Device Manager Version 5.2(4)
[Code]......
how can I enable an automatic power-on after a power failure on an ASA 5512-X?
View 5 Replies View RelatedI have a SF-300-48P that is power cycling all POE ports (in use) exactly every 30 minutes. The other older cisco POE switches we were replacing did not have this issue. We have about 40 cisco SPA942 IP phones connected to it. Power consumption is about 175 watts total.
This is my second switch, previously tried a SG500X-48P with the same result.
how to stop it from cycling?
the only change that survived power cycling is the change of default password that it forced me to do.
View 2 Replies View RelatedI've got a WRSV4400N v2. Latest firmware. Every sunday, it becomes unresponsive and needs power cycling. After that, it works fine for a week. AT&T DSL. Hooked up to a Windows 2008 R2 server. There is also a Mac Xserver on site.
View 4 Replies View Relatedhow can I enable an automatic power-on after a power failure on an ASA 5512-X?
View 12 Replies View RelatedMy ASA 5505 getting pretty hot after a while and so I used a wattmeter to find out what´s happening.
260 watts is quite a lot if the device is running in idle mode and has no active device attached nor any config has been installed.
What's your experience of the ASA 5505 power consumption ?
We have several SF-300-48P switches, eveytime there is a power failure the switches need to reboot 2 or 3 times before they are able to route packets again.
View 1 Replies View RelatedI've got the power cut while PC was running (w7). After rebooting I'm not able to connect to the internet anymore.
In Device Manager, under Network Adapters there is a "Realtek PCIe GBE..." device properly installed. But under Other Devices there are now more entries with exclamation mark:
- Network controller
- Multimedia controller
- PCI Communication controller
etc
I tried updating the drivers, then deleting and reinstalling but no success so far. Still can't connect to the internet. The browser can see the router, at 192.168.1.1 I don't know where the problem is.
We have cisco wlc 2125 with 13 AP 1131g. All works good. But after power failure one AP can not join to controller, only reset work to recover connection AP to WLC. Additionally, we don't have access to rs-232 port on AP. In this moment on WLC we can see DISCOVERY request from AP and response from WLC to AP, but AP don't send JOIN to controller.
View 2 Replies View RelatedI have a WS-C6509-E (R7000) and am trying to implement some proactive monitoring for environmental alerts. What is the output from a Power Supply failure for the following “sh log” “sh environment alarm”.
View 1 Replies View RelatedI'm having the following issue with a couple of 1231's.
Some overall config info first:
This is a small office with 2x Catalyst 2950 (24-port, no PoE) switches and 4 AP1231G (autonomous). The APs get PoE from a PWRINJ3 each. The injectors are powered by the AP power supplies. Injectors and power supplies are mounted in the patch closet.
The 2 switches are connected together over 4 ports (20-23 on each switch), these ports are set to 1Q Trunk mode.
The APs are connected to the switches, 2 to each switch, on port 1-2. These ports again are configured as 1Q Trunk.
APs are connected to the switch as follows:
[switch] <- patch cable-> [injector] <- patch cable -> [patch panel] <- static cabling -> [outlet] <- patch cable -> [AP]
All this has been working without problems for a number of years.
A few weeks back, AP2 did not restart after a power cut (everything else did). All LEDs are off, port on switch has no LEDs lit. I did not get around to investigating this furtehr until last week. I unmounted (failed) AP2, took it to the spot where (working) AP3 hangs, and plugged it to the cable of AP3. AP2 came to life immediately. I unplugged it and plugged AP3 back in, which restarted immediately.
So I suspect a power supply issue on AP2. I took the injector and power supply that fed AP2 out of the patch closet. When connecting AP2 directly to the power supply, it came to life immediately. So I figure the injector is defective.
On the same day, I notice AP4 is also dead (again all LEDs off, no idea how long, could have been that day or could have been a few days - it has definitely been working after the power cut that appeared to have killed AP2).
So I order 2 new PWRINJ3s and for good measure 2 new power supplies. Later that day, I took the injector and power supply that fed AP4 out of the patch closet. When I try this combination (AP4, injector4 and P/S4), and connect it to a different wall outlet (and therefore a different port -16 - on the switch) IT WORKS! Should have triggered questions, but did not immediately.
Last Thursday I got the new injectors and power supplies. So I take one of each, hook them upto AP2 at my desk, and AP2 starts up. So I mount new injector2 and new P/S2 in the patch closet, put AP2 back in its place, connect all the cables - NOTHING. AP2 does not start. The "power" LED on the injecvtor lights up green, the "device status" LED remains off. I take AP2, new injector2 and new P/S2 to my desk, hook them upto a wall outlet (connected to switch port 17). AP2 starts immediately.
Meanwhile AP3 has (also) stopped working (no LEDs on at all). As far as I can tell, it stopped working after I briefly disconnected (and reconnected) the patch cable between injector3 and the patch panel in the patch closet. The LEDs on switch port 1 are off.
I have since tried to power cycle both switches (took power off both, waited a while, poewerd both back on). No change.
PS: the APs ran firmware 12.3(8)-JA until recently. AP1, AP3 and AP4 were upgraded to 12.3(8)-JEE after the the power cut that took AP2 out. THis is when I found out AP2 was dead. AP2 was still on 12.3(8)-JA. It was upgraded to 12.3(8)-JEE last week when it was on direct power on my desk.
We had power failure catalyst 6509 and after the device boot up ssh does not work any more below is error messages
line con 0
access-class 90 out
logging synchronous
[Code]....
Thinking back, about a month ago I updated the firmware (I can't check version at the moment). The switch has been working fine since then. Today I needed to move some power cables and the switch lost power. Now ALL of the LED lights are flashing green and I can't access the switch. I've tried setting a static IP on my laptop to 192.168.1.20, mask 255.255.255.0, and accessing the switch on 192.168.1.254, but there's no response. I've tried holding in the reset button for at least 30 seconds while the switch is powered on, AND while powering it on. None of that has worked. Also when I first power it on, the system LED flashes orange very quickly for a second or so, then all of the LEDS start flashing green.
View 5 Replies View RelatedAfter a recent power outage while my PC was in sleep mode, I don't have wired (Ethernet) connectivity.
I have new Dimension E510XP Media Center Edition, Version 2002, SP3 ver had an issue with wired connectivity on this PC after coming out of sleep mode. Of course, the power failure was unusual.
Observations:
- ipconfig /all shows that I have an IP address
- I can ping the DHCP server listed in ipconfig /all and I also can ping google.com.
- I was going to go a restore point set before the power outage. But, somehow system restore had gotten turned off. Oh, well. I did go ahead and turn system restore back on.
Things I've already tried that did not solve the issue:
- Reboot
- Uninstall/reinstall the network adapter driver. Device Manager says the network adapter card is working properly.
- Looked for an updated network adapter driver on Dell's website. Turns out that I have the latest driver already.
- Followed many of the steps from Microsoft at [URL]
- Checked McAfee Security Center firewall permissions list to see if something got changed. Everything looked okay. Also disabled the firewall just to be sure,
- Disabled SafeEyes internet filter.
- Reset the router. Also swapped router ports with a known good PC. The known good PC still had connectivity, the affected PC (the E510) did not.
I have a switch 3560v2 with an IOS 12.2(50) SE1.All the lights ON and console error message below:POST: inline power post failed for port 0 up to port 15.Then, the system hanged and all lights (indicator) ON.
View 5 Replies View RelatedMissing local area connection icon in network connection after power failure?
View 1 Replies View Related1、the router power led's emitting light very weak ,
2、client pc cannot get ip from connected router
these error perhaps happened after a plug power jack action. Dc-dc chip is ME5513,the voltage on its pin4 is about 11.94V,and the voltage on following electrolytic capacitor is 3.3V,its seem normal.
I have a ~3 month old e1000 v2. In the last 24 hours it appears to have died, all 4 ethernet lights plus the power light and the one to it's left are on continuously. Before I dispose of it, does anyone know if this really is a hardware fail or is there some way to recover it? I've tried a few resets, power cycles and leaving it off for a few hours in the hopes that would bring it back to life but to no avail.
View 5 Replies View RelatedI am running ASA 5505 release 8.2(4) using a clientless SSL vpn to connect my assessors to the server via RDP to a Terminal server. Everything was working fine until last week when we had a Internet outage. During the outage some of the assessors claimed to have accepted a Cisco add-on to get into the site. once the internet came backup they could not connect to the terminal servers - what would happen is they would click on the link - say OK to connect the clipboard and the screen would pause for a few seconds then right back to the select options page.
they can get to other servers (non-terminal servers) but not to the ones they need. I can recreate the issue by waiting a REALLY long time before replying to a prompt to install an cisco add-on. I have users that can connect and others than can not. Also this only seems to affect Internet Explorer 8 and 9 does not affect Firefox
I am having trouble accessing shares via client SSL VPN. I have an ASA 5505 running 8.4(4)1 The share is on on Ubuntu server 11.04 running Samba 3.5.8
This may not be strictly a Cisco issue and it seems to be an interoperbility issue between ASA and Samba. Or simply the smb.conf configuration.
I suspect the issue is down to the interpretation of Lanman on the ASA as I know the usernames and passwords work correctly when accesing the shares from other platforms (Windows Vista and Ubuntu desktop 12.04)
When monitoring the Samba logs I get the following errors: (amongst others)
ntlm_password_check: NT MD4 password check failed for user testuser
Storing account testuser with RID 1000
check_ntlm_password: sam authentication for user [testuser] FAILED with error
[Code].....
Connection denied due to NAT reverse path failure
View 2 Replies View RelatedI have a LAP1142N that is connected to a 3560 nonPoE switch (using compatible power injector) that will not associate to the controller I have set-up. The wireless is existing and I have about 11 other APs connected to the controller with no issues. The AP will pull an IP address from DHCP running on the primary controller. The AP pulls a new IP address in roughly a minute. I set the pool to be 3 IP addresses and set a contant ping to each, there is about 1 request time out before the next IP address starts pinging. I went to the controller and pulled the following message error from the log.
*Feb 13 14:24:58.614: %LWAPP-3-HDR_ENCAP_ERR: spam_lrad.c:4216 Unable to encapsulate LWAPP header for discovery response; AP (APs MAC address)
*Feb 13 14:24:58.614: %APF-3-PDU_ENCAP_FAILED: apf_net.c:771 Failed to encapsulate a PDU for transmission to station00:00:00:00:00:00. Destination IP address not set in L3 mode.
I have tried a different cable, connecting to a PoE switch, different controller, larger DHCP range, hosting DHCP on the distribution switch, I am awaiting console access to the AP since this is remote work. The controller is running Software Version 5.1.151.0. Thoughts?
console inventory output from GUI
Model No. AIR-WLC4402-25-K9
Burned-in MAC Address XXXXXXXXXX
Maximum number of APs supported 25
Gig Ethernet/Fiber Card Absent
[Code] ....
I have a 2811 Router that keeps cycling through reboots. About 30 seconds into a boot, it shows the ALIGN-1-FATAL error(s) shown below. It then does a dump and reboots. This cycle just continually occurs.
Readonly ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xcb80 (code)
I've had a WRT54GL ( for about a week now ) with no real issues. Today my wife mentioned that the net's been flaky ( wireless nto hard wired ). I originally noticed what seemed like minutes for my desktop of laptop to connect to any web pages. Loads were extremely slow. According to the computer I had a 1 mbps connection. I did the standard resetting of the modem and router.babble babble babble. Eventually, I ran a wifi analyzer from my phone to determine an ideal channel. However, while running the frequency scanner I also noticed that my broadcasting would continue to drop off the radar for a quick moment then return. This seemed to be true no matter what channel I set. What's interesting is that the signal would read as extremely strong for 45 sec - 1 minute, then completely drop the signal, then another strong broadcast. Other neighboring signals don't exhibit this behavior....well I would see the weaker signals coming in and off the radar from time to time. I'm guessing it's some type of interference? However if that's the case I can't explain why my signal seems so strong. I'm assuming I'd see a lot of fluctuation in my signal before dropping off ( instead of going from 100 to 0 in the blink of an eye ).
View 1 Replies View RelatedAfter the upgrade of the WLC 5508 to version 7.4 the 1142 access-points LED blinking rapidly cycling through blue, green, and red. I found the following information to this behavior: "Access point location command invoked"
The configuration didn't change. How can I switch this function?
i know in Cisco PIX til 8.2 OS, if i have Nat control disabled and ACL permitting connection from Low Secirity ( DMZ ) to High Secuurity (INSIDE) then connectino should be successful, and i dont need any STATIC identity nat of inside IP to be created.
But i have Cisco PIX 525 with Version 7.2(2) Which is not allowing connection from DMZ to INSIDE , although nat control is disabled. and giving RFP check failure, any thought?
PIT525PIXINET# sh running-config nat-control no nat-cont
packet-tracer input dmZ tcp 192.168.85.4 65000 10.34.21.25 3389
Phase: 1
Type: FLOW-LOOKUP
Subtype:
Result: ALLOW
Config:
[Code]...
Having an issue getting my DMZ vlan working. Running my ASA5505 and i have configured e0/2 for DMZ w/ VLAN ID 3. Connected to my 2716 on port2.Inside e0/1 w/ VLAN ID 1. Connected to my 2716 on port1.
I am trying to get my DMZ Vlan to ports3&4 (LAG1) but when i assign the LAG group to PVID 3 i lose connectivity on VLAN1. I want to send both VLANs to that host because the teamed adaptor is used for Hyper-v Network Switch.
I have 7604 router with FWSM module in module 3.First of all the FWSM CF has been damaged, not physically. I bought the new same compact flash (size, partnumber, etc.). Downloaded the software 3.2 for FWSM, and ASDM from Cisco website. I realized that the procedure of creating new CF for FWSM is quite diffucult: creating 1-5 partitions, where 1 - is MP, and 4th - application partition. According to cisco documentation - the default boot partition is the 4th, so I partitioned from 7604 the CF into 4 partitions (partition disk1: <1-4> maximum) and copied the software and ASDM to the 4th partition (disk1:3:). Removed the CF from the router and put it into the FWSM module.
View 1 Replies View RelatedI have two ASA 5520s in Active/Standby. I try and test this quartely to ensure it is working correctly. Everything works fine, except I have an issue with one interface. When doing a show failover, it shows the interface as failed on the secondary unit, and I am not sure why. It shows it as normal on the primary.
This host: Primary - Active
Active time: 9277305 (sec)
slot 0: ASA5520 hw/sw rev (2.0/8.2(4)) status (Up Sys)
Interface WaterworksCanopy (192.x.x.x): Normal
[code]....
I am using a Pix515E with 8.0(3) and 128MB RAM. It ran OK for months but has recently had several episodes during which it produced streams of memory allocation failures (syslog 211001). When in this condition I could not log into the VPN. It was still operating but some users were having problems and I eventually had to restart it.
The traffic load is typically 10Mbps, and the max number of connections is around 10,000 but typically 5,000. The CPU usage is 10%-20%. There is 1 VPN with normally 1 client. The memory usage is always high, between 115MB and 120MB but during these problems it creeps higher.
Why might the memory usage be so high when my network load is quite light for the 515E? What circumstances cause the memory usage to increase during operation? Is there anything I can do to prevent the memory usage increasing to the point where the PIX crashes?
I have a second 515E with 8.0(4)32 and 64MB RAM, loaded with the same config. I have not had this one in service, but off-line it is using 53MB of memory. If the spare pix needs 53MB to load the firmware and my config, why does the other one use 115MB?
Ive got a virtualised firewall running 3 security contexts in routed mode. What am experiencing is that i cannot connect to an OUTSIDE host through the security contexts. From the firewall itself i cannot ping the directly attached host on the OUTSIDE interface but i can ping the directly attached host on the INSIDE interface. When i reload the firewall box, the first ping to the OUTSIDE host would be successful but subsequent pings fail and thus total connectivity is lost.
I even tried upgrading to ASA version 8.4(1) but still the same.