My ASA 5505 getting pretty hot after a while and so I used a wattmeter to find out what´s happening.
260 watts is quite a lot if the device is running in idle mode and has no active device attached nor any config has been installed.
What's your experience of the ASA 5505 power consumption ?
Can I mix up a 350 Watts PS and a 715 Watts PS on the same Catalyst 3kX switch?
View 0 Replies View Relatedwhat is the NM-32A card power consumption?
View 2 Replies View RelatedI am finding the power consumption of WS-C3750X-24T-L, WS-C3750X-48T-L, WS-C3560X-48T-L and WS-C3560X-24T-L switches?
View 5 Replies View RelatedWe are planning for the office move and I need to estimate how much power we need to run a fully populated Cat4507R switch. The chassis include 2 Sups, one 6-port fiber line card, two 48-port Gig and two 48-port FastEthernet line cards. The switch also has redundant power supply (4200ACV 1400W). According to Cisco Power Calculator [URL], I need 49.5 amp 110-120V circuit. It seems to be too much higher than real world. How many 20amp circuit we would need when all the ports are fully utilized?
View 3 Replies View RelatedWhat is the power consumption of the 6-port 40G M2 module for the NExus 7K?
It says "TBD" on the data sheet for the M2....and it says nothing about power for the Supervisos.
I need to know what the power draw is on a 7009 chassis, with 1 SUP and 5 of these cards....
I wondered, how much power do the SRP520-U series actual draw? Compared to commonly used home-grade equipment I think the power consumption is above average?
View 1 Replies View RelatedI have 2 x 3560e-24td-s
2 x ASA5510
2 x 2821(no modules)
2 x 2901
I'm trying to figure out power draw in Amps for my new cabinet. I looked at the data sheet for the 2821 and it says 3A for the 110V under the row AC Input Current, Would that be accurate if I did that for all the models and then just added up the total?
For a AIR-LAP1524SB-A-K9 Mesh Access Point I need amp (I) and power (W) consumptions of the power source options (12 VDC, 220VAC, etc.).
View 2 Replies View RelatedI need to figure out the max power consumption of 7009. The issue is, at this point i am not sure what modules will be used, so just to give an estimate, how we calculate the max power consumption of nexus 7009 ?
View 2 Replies View RelatedI am calculating Cisco 4500X power consumption requirements to select appropriate UPS systems. I have 4500X switch with dual power supplies.which value should I take for power consumption calculation, in data sheet it has two values: AC Power Max Rating: 750W System Power Consumption: 330W nominal/400W max
Which values should I take, to calculate UPS systems capacity? And also I am interesting when 4500x has two power supplies what is power consumption?
I have a problem with the configuration of the ACL of my ASA 5505 router.However, the syntax seems okay,access-list 121 extended deny icmp 192.168.0.0 255.255.255.0 .
View 3 Replies View RelatedI have a 5505 configured with a active/standby dual wan setup using the sla tracked connection settings. Is there a way to configure the ASA to stay on the backup connection after activating? We had a situation where the main T1 was bouncing, so the backup connection was being activated and deactivated very often. The problem is that there is an app being used that does not allow users to reconnect to dropped connections immediately, so every time the asa switches wan connections it causes a significant disruption.I should note that I already set monitor options frequency to 240 seconds. I could set it higher, but then we have a longer delay when the main connection dies.
View 2 Replies View RelatedI bougth a used ASA 5505 on ebay which is experiencing this problem [url]... LEVELS or at least the described problem, if i touch the appliance while it is running it will somtimes go to this non working state as well
View 11 Replies View RelatedFirmware asa805-k8 was installed and saved on an ASA5505. Upon power failure the ASA5505 reverts to an older firmware, asa724-k8. 1) Is it normal for ASA5505's to revert to older version upon power failure. 2) ASDM/web browser doesn't work using IE--username and password brings to empty screen. how to revert back to later image.
"
# sh ver
Cisco Adaptive Security Appliance Software Version 7.2(4)
Device Manager Version 5.2(4)
[Code]......
What is the required power by WAP321 ? There's no information about IEEE 802.3af class at the datasheet.
View 1 Replies View RelatedWhat is required power in Watts for this card in Catalyst 6500? Or the "show power" ouput with this card included?
View 2 Replies View RelatedWe have one switch 4510R which could have total 300 cisco GE color phone connected. That means 300x15.4=4620W. Considering the 89% effiency for the PoE line cards, that means each line card needs 5191W input power from chasis power supply. Based on the 6000W power supply specs, only up to 4800W is allocated for PoE purpose. But we need 5191W from power supply which redundant mode can't offer. We don't want to go with combined mode. So should we add external power shelf to add more power?Another question will be how much power we need from utility or UPS. For example, the efficency of cisco power supply is 75% and we use two 6000W power supplies in redudant mode. Then we need 8000W. The voltage is 220V. Then the AMP we need is 36.4A from UPS or utility power.
View 2 Replies View RelatedWhen our DSL modem drops its connection, even momentarily, the RV220W requires a power cycle before the computers on the LAN can browse again. When I connect to the router, the WAN Information displays the word Connecting, rather than Connected.
We have a DSL modem connected to the router, the router connected to an ethernet switch, and our small business pc's connected to the switch.
Firmware on the router is 1.0.4.17
From what I understand, it requires a 5V 2.5A adapter ... alas, cannot find one.
View 2 Replies View Relatedhow can I enable an automatic power-on after a power failure on an ASA 5512-X?
View 5 Replies View RelatedI'm getting currently installing a full Valcom IP sound and clock system , along with all new Cisco 2960 gig ps-l switches. All devices run off of POE. In the past, I have read that most AP's only draw approx. 12.5 watts (va's). But you must take into account length of wire to add your additional draw which puts you at the 14.5 they auto draw. My question being that the clocks I have auto draw 15.4 watts, which is eating up my 370w of power on my switches. The spec sheet on the clocks show only a power consumption of 4.5 watts. So today I turned a few ports down to 4.5 watts and everything still worked fine.. Any experience by chance with Valcom devices or just turning the power down on devices in general? I can imagine that a clock is drawing enough to care about the length of the wire run.
View 8 Replies View RelatedI am quite new to firewall, in my company one asa 5510 firewall is there.I configured inside, outside, dns, dhcp and nating.I need to config bandwidth limit (1Mbps) for inside port and I restruct like facebook, youtube and pornsites..And I heard that some subscription is required, really is it required?
View 1 Replies View RelatedI have one firewall need to be configured in transparent mode. I have inside and outside router. What is the configuration of transparent firewall ASA8.2. I didn't find the configuration on Cisco site.
View 17 Replies View RelatedHave a kill-a-watt and a Netgear FS105 switch? and if you do how many watts does the unit take idle and under network load?
View 5 Replies View RelatedI am very confused on how I setup a Pix 515 that I just got to route traffic out a cable modem. First, let me give you a little details on my current network setup and what I am trying to accomplish with this Pix 515. Currently all my users go out the proxy for any internet access, however I have certain users that need to go out the cable modem instead of the proxy server. Below is an example of the current IP setup of a user A:The cable modem that we currently have has DHCP so I would need the external PIX address to accept a DHCP address. I also don't really understand what else I need to setup so if I have say four users hitting the cable modem through the pix how do I direct their web traffic to the correct computer (NAT ?),I will be plugging the PIX into a cisco switch that all ports are in VLAN 48 so hopefully a static internal address on the pix of 10.24.48.254 will keep me from having to do any routes since all traffic will be originating from the 10.24.48.0 network.
View 1 Replies View RelatedI have two ASA 5510 with Security Plus license and Shared SSL VPN licensing enabled.
The problem is that the client get “Session could not be established: session limit of 25 reached” but ther is only 6 ssl vpn user connected with AnyConnect.The software on the firewall’s is 8.2(1)Is there any BUG in this software related to this problem?
We have purchased a new Websense 10000 Appliance and I'm not a hundred percent how to set this up. I see that URL Filtering is a possibility and WCCP, which way to move forward on implementing this?
View 4 Replies View RelatedI am trying to set up my Cisco 520 router with a firewall that will: Allow port 80 traffic to the vlan 20,Block all other incomming ports to vlan 20 (unless initalised from inside),Allow all outgoing ports on vlan 20,Block all access from vlan 20 to vlan 10 (unless initalised from vlan 10)
View 35 Replies View RelatedI'm in the process of migrating a rather big NAT configuration from a customer running pre 8.2 ASA software.The customer has 2 Dynamic Policy NAT configured which have overlapping source addressesOther Dynamic Policy NAT has the destination address of "any"
Other Dynamic Policy NAT has a single host address as destination address towards InternetThe Dynamic Policy NAT configured with the "any" destination is applied to all translations for the source host towards Internet
What I'm interested in is the following
Since both NAT statements are equal in a sense (because they are of same type) what is the next deciding factor for ASA decides which translation rule to use?
Does the "nat_id" parameter define which rule is checked first? Is the NAT rule with the lowest "nat_id" value used regardless what the order of the NAT rules is when you check them on the CLI? (with "show run global" and "show run nat")I'm just interested on how the NAT operates in this case, even though were generally using 8.4 at the moment.
I upgraded my ASA 5520 with the latest image. Now I get an error upon launching ASDM.Your ASA image has a version number 7.2(4) which is not supported by ASDM 6.4(1), use Device Manager version 5.2(x)Continue Anyway?
What are the newest, recomended image versions of ASA and ASDM I should be using?I will also be using the SSM-20 module with this setup, so I would like to stay with a working version of ASDM.
I am looking into buying an ASA5505 but I would like to know if it is going to work in my setup. I have an Internet connection and 2 seperate networks. I know that the ASA5505 has 8 ports and I would like to know if I can assign each port to a different network zone? I dont want to use VLAN but physical networks. I know it is possible with ASA5510 and above but I want to make sure I can do the same with a ASA5505 (Without the security upgrade). I want to get an ASA5505 unlimited users.
So an Internet connection (with multiple IPs), 2 seperate networks, I want to filter traffic between all 3 and route between them also.
I have a SBS 2008 box at a clients with 16 gig of ram in it. Right now the server is using 88-90% of it's ram. I have checked the device manager to see how much ram the services are using and everything except for a few services are using less then 200,000k each. The exchange store is using around 600,000k which is right in range and then a couple w3wp.exe services are using around 300,000k or less. Now here is where the issue lies 3 SQL engine processes are using a total of around 7 gig of ram. My client runs a custom software that uses sql express to host the database. And I am just wondering if it's normal for SQL to use this much ram in 2008 or should I be talking to the software company about the large consumption. It's basically using half of the available ram on the server. I did upgrade this machine from 8 gig ram about 9 months ago and it was fine for a while then all the sudden SQL just started eating more ram to point where we are today.
View 10 Replies View Related
