I've got a WRSV4400N v2. Latest firmware. Every sunday, it becomes unresponsive and needs power cycling. After that, it works fine for a week. AT&T DSL. Hooked up to a Windows 2008 R2 server. There is also a Mac Xserver on site.
View 4 RepliesI have a SF-300-48P that is power cycling all POE ports (in use) exactly every 30 minutes. The other older cisco POE switches we were replacing did not have this issue. We have about 40 cisco SPA942 IP phones connected to it. Power consumption is about 175 watts total.
This is my second switch, previously tried a SG500X-48P with the same result.
how to stop it from cycling?
I bougth a used ASA 5505 on ebay which is experiencing this problem [url]... LEVELS or at least the described problem, if i touch the appliance while it is running it will somtimes go to this non working state as well
View 11 Replies View Relatedthe only change that survived power cycling is the change of default password that it forced me to do.
View 2 Replies View RelatedWe have a WRSV4400N installed as our primary NAT Firewall. It is configured to allow Windows VPN connections to our server residing on the Internal Network Domain - this works fine.Problem is that even though the remote VPN client can open shares, browse the internal network, and resolve computer names fine with DNS, but... Remote Desktop will not connect using the VPN tunnel.We need this to work... I spent several hours with your support people when installing this router a year ago and got nowhere. And everythung else works fine.I am using Windows server-based VPN because your VPN Clint didn't work ata ll either. Can you perhaps give me a list of configuration settings to check?
View 3 Replies View RelatedI am having trouble connecting the Amped Wireless AP600EX access point to my WRSV4400n. As soon as I plug the range extender into the router, instead of it receiving an IP address, it crashes the router. I have updated the router firmware to 2.021. I have checked the box in the WDS menu to "allow wireles signal to be repeated". I will check with Amped, but are there any known issues between this router and the Amped Wireless family of range extenders?
View 1 Replies View Relatedis it easy to remove the 3750x stacking? i'd like to test one of them on a sunday and keep the other one on production. it's just two stack of 3750x, is it hard and do i really need to remove the cables on the back?
basically i need to put a different config for my testing, i gues i need to remove the cables right? and put it back on the stack before monday.
I have a LAP1142N that is connected to a 3560 nonPoE switch (using compatible power injector) that will not associate to the controller I have set-up. The wireless is existing and I have about 11 other APs connected to the controller with no issues. The AP will pull an IP address from DHCP running on the primary controller. The AP pulls a new IP address in roughly a minute. I set the pool to be 3 IP addresses and set a contant ping to each, there is about 1 request time out before the next IP address starts pinging. I went to the controller and pulled the following message error from the log.
*Feb 13 14:24:58.614: %LWAPP-3-HDR_ENCAP_ERR: spam_lrad.c:4216 Unable to encapsulate LWAPP header for discovery response; AP (APs MAC address)
*Feb 13 14:24:58.614: %APF-3-PDU_ENCAP_FAILED: apf_net.c:771 Failed to encapsulate a PDU for transmission to station00:00:00:00:00:00. Destination IP address not set in L3 mode.
I have tried a different cable, connecting to a PoE switch, different controller, larger DHCP range, hosting DHCP on the distribution switch, I am awaiting console access to the AP since this is remote work. The controller is running Software Version 5.1.151.0. Thoughts?
console inventory output from GUI
Model No. AIR-WLC4402-25-K9
Burned-in MAC Address XXXXXXXXXX
Maximum number of APs supported 25
Gig Ethernet/Fiber Card Absent
[Code] ....
I have a 2811 Router that keeps cycling through reboots. About 30 seconds into a boot, it shows the ALIGN-1-FATAL error(s) shown below. It then does a dump and reboots. This cycle just continually occurs.
Readonly ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xcb80 (code)
I've had a WRT54GL ( for about a week now ) with no real issues. Today my wife mentioned that the net's been flaky ( wireless nto hard wired ). I originally noticed what seemed like minutes for my desktop of laptop to connect to any web pages. Loads were extremely slow. According to the computer I had a 1 mbps connection. I did the standard resetting of the modem and router.babble babble babble. Eventually, I ran a wifi analyzer from my phone to determine an ideal channel. However, while running the frequency scanner I also noticed that my broadcasting would continue to drop off the radar for a quick moment then return. This seemed to be true no matter what channel I set. What's interesting is that the signal would read as extremely strong for 45 sec - 1 minute, then completely drop the signal, then another strong broadcast. Other neighboring signals don't exhibit this behavior....well I would see the weaker signals coming in and off the radar from time to time. I'm guessing it's some type of interference? However if that's the case I can't explain why my signal seems so strong. I'm assuming I'd see a lot of fluctuation in my signal before dropping off ( instead of going from 100 to 0 in the blink of an eye ).
View 1 Replies View RelatedAfter the upgrade of the WLC 5508 to version 7.4 the 1142 access-points LED blinking rapidly cycling through blue, green, and red. I found the following information to this behavior: "Access point location command invoked"
The configuration didn't change. How can I switch this function?
I have a SRP527W what has a constantly flashing power LED.Is there anything that I can do to attempt to recover this router?
View 2 Replies View RelatedI wondered, how much power do the SRP520-U series actual draw? Compared to commonly used home-grade equipment I think the power consumption is above average?
View 1 Replies View Relatedwhere i can buy a power adapter/supply for the AC1200 wireless router?
View 1 Replies View RelatedI need power supply for N wireless modem router F5D8633-4. It says 15v 0.8A on the router but I can only find 15v 1A available on the internet.
View 2 Replies View RelatedI have been given the task of unbricking a WRVS4400N V2 router. It just sits there with the Power and Diag lights blinking and does nothing else.I'm thinking I'm going to have to try to find some way to flash the firmware, because I'm seeing that this is a common problem with this router.I already tried support "chat" online, but after about 20-30 minutes waiting for someone to actually come into the chat room, I gave up.I did note that this model is not being sold anymore and won't be supported before very long, so this may be a gigantic waste of time, but I thought I would give it a shot.
View 2 Replies View RelatedI have two RV180W's which are excellent units in almost all respects. The one really noticeable problem is that when I have a power outage (which I have quite a lot in rural France) my RV180W does not automatically restart when the power is restored. Is it not possible to fix this in the next firmware upgrade, or have I missed something in the router menu/setup which I should have set.....?
View 1 Replies View RelatedWe have a Cisco SRP 527W router that was not showing up on the LAN. so we tried a Factory Default reset but it seems to be dead.
The power light is flashing constantly,the 4 LAN light are constantly on,the DSL Data light comes on for 1 sec when device is powered up.
i have tried connecting directly to a PC, the NIC reports as network cable unplugged.i have tried the (power on device, hold down reset button, power of after 30 sec, power on after 5 sec, release reset button after 5 sec) but still "network cable unplugged".
the firmware flash utility will not find the NIC the device is connected to.the router is less than a year old, is there a fix or is it a warranty replacement ?
I connected an EnGenius M5000 AP/Bridge to a switch, a Modem (VSAT) is also connect to the switch and aslo my Desktop standalone PC. All instructions were followed to install the EnGenius M5000. However, only the Power,Lan, and Wan light indicators are on but the Link/Signal indicators - red, yellow and green are not coming on.I tried pinging 192.168.1.1 according to the default IP address, but still there was no responds. Even I tried resetting it on the firmware, but it can not ping
View 2 Replies View RelatedThe instructions say to power off the modem but the modem is also for the phone and has a battery backup. How do i proceed? model N300 wireless router
View 1 Replies View RelatedWhat is the part number of the power-supply of this router (WRP400)? [code]
View 6 Replies View RelatedWhen our DSL modem drops its connection, even momentarily, the RV220W requires a power cycle before the computers on the LAN can browse again. When I connect to the router, the WAN Information displays the word Connecting, rather than Connected.
We have a DSL modem connected to the router, the router connected to an ethernet switch, and our small business pc's connected to the switch.
Firmware on the router is 1.0.4.17
found that the problem is (temporarity) corrected after we power cycle the router.
The firmware installed in the latest published. See below:
System Information
Serial Number : NKS15481665 Firmware Version : v4.2.1.02 (Jan 18 2012 14:10:55)
PID VID : RV016 V03 Firmware MD5 Checksum : a9817f2dbdcbd6a5c109eaa21b1c3545 ystem InformationSerial Number : NKS15481665 Firmware Version : v4.2.1.02 (Jan 18 2012 14:10:55) PID VID : RV016 V03 Firmware MD5 Checksum : a9817f2dbdcbd6a5c109eaa21b1c3545
I am receiving the following error on 3750 stack switches. have already verified the power status and found ok.
IOS used: Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
211540: Jun 10 10:45:17.935 UTC: %PLATFORM_STACKPOWER-4-UNBALANCED_PS: Switch 4's power stack has unbalanced power supplies
211541: Jun 10 10:46:18.045 UTC: %PLATFORM_STACKPOWER-4-UNBALANCED_PS:
[Code]....
After stacking two 3750X switches, with four equal power-supply's, with StackWise and PowerStack , still got the next message every few hours %PLATFORM_ENV-1-FRU_PS_ACCESS: FRU Power Supply is not responding (gn4m-rt1p08-04-2)( note that the message revers to the second switch in the stack ) although the stackwise and powerstack on the switches is oke and are working correctly. !
Config : Stack-power in power-sharing mode/strict With CLI on the switch : All the power supply's and stack-power details, prio look OK.
Only: LMS prime /inventory/cisco-view/configure/power supply status result : some power supply's are marked as disabled.with the command > power supply 2 slot a off/on I manage to get the status back to "normal", but after a few hours some power supply's are again marked as "disabled".
Looks like SNMP en IOS difference from opinion.
Hardware
WS-C3750X-24S-S
C3KX-PWR-350WAC
Software
15.0(2)SE
C3750E-UNIVERSALK9-M
I keep getting alerts from our WCS stating that our 1252s are drawing low power. Now I am aware that they require enhanced PoE (up to 20W) but as we only have standard PoE in that building we purchased the 1252 series power injectors to go with them.
However, even with the correct power injectors the WCS still reports the draws low power error.
Is this a bug? Running WCS 7.0.172 at the moment.
Forgot to say we are using the PWR-INJ4 and the injector status is enabled and you see the injector MAC address when you drill in to the AP status.
We have two switches of the same model (WS-C3560-48PS-S) that are not providing PoE. I'm trying to remotely determine what the cause of the issue is.
Here is some output.
Hostname#show power inlineAvailable:0.0(w) Used:0.0(w) Remaining:0.0(w)
Interface Admin Oper Power Device Class Max (Watts)--------- ------ ---------- ------- ------------------- ----- ----Fa0/1 auto off 0.0 n/a n/a 15.4Fa0/2 auto off 0.0 n/a n/a 15.4Fa0/3 auto off 0.0 n/a n/a 15.4Fa0/4 auto off 0.0 n/a n/a 15.4Fa0/5 auto off 0.0 n/a n/a 15.4Fa0/6 auto off 0.0 n/a n/a 15.4Fa0/7 auto off 0.0 n/a n/a 15.4Fa0/8 auto off 0.0 n/a n/a 15.4Fa0/9 auto off 0.0 n/a n/a 15.4Fa0/10 auto off 0.0 n/a n/a 15.4(code)
I have a 6500 chassis with 2 power supplies. At the moment I am using the default configuration:
power-redudancy mode redundant
The problem is that an inserted module is in "power deny" state due too insufficient power.
I know, that It's not a good idea to change into combined mode (loss of redundancy), but my customers requested this anyway.
So I will change to combined mode. So here's the 1 million dollar question: "Which modules will go into power deny, if one of my power supplies fails?"
The 6500 config guide states:
"Power supply is removed withredundancy disabled
• System log and syslog messages are generated.
• System power is decreased to the power capability of one supply.
• If there is not enough power for all previously powered-up modules, some modulesare powered down and marked as power-deny in the show power oper state field."
Well, do you know if there's any way to configure some kind of priority? E.g. I definetly don't want by 10Gig Module or WiSM module to be in power deny. Can i statically make sure, those module will be powered on for sure? Like: "power enable module slot_number" How is this calculated? Or is random?
In a stand alone 3750x switch configuration, can the secondary power supply only act as a redundant power supply (active/standby), or can it become a "pool" of power similar to power sharing mode for StackPower (somewhat active/active)? I understand there is no stack involved here but I'm curious if this functionality is possible.
View 1 Replies View Relatedhow can I enable an automatic power-on after a power failure on an ASA 5512-X?
View 5 Replies View Relatedhow can I enable an automatic power-on after a power failure on an ASA 5512-X?
View 12 Replies View RelatedI'm new on this version and I don't know how to create a Monitor/Alarm to detect that a power supply has gone down. I want to send a message.
View 1 Replies View RelatedAny trouble with IOS XR licenses dissapearing after a power off ?I was able to add them correctly, but after the power off "show licenses" gives and empty message, but the logs states the licenses are already there.I'm working with a CRS-3 with IOS XR version 4.0.1.
View 1 Replies View Related