Can't Connect To Internet After Power Failure

Apr 18, 2012

I've got the power cut while PC was running (w7). After rebooting I'm not able to connect to the internet anymore.

In Device Manager, under Network Adapters there is a "Realtek PCIe GBE..." device properly installed. But under Other Devices there are now more entries with exclamation mark:

- Network controller
- Multimedia controller
- PCI Communication controller
etc

I tried updating the drivers, then deleting and reinstalling but no success so far. Still can't connect to the internet. The browser can see the router, at 192.168.1.1 I don't know where the problem is.

View 4 Replies


ADVERTISEMENT

Dell :: How To Enable Automatic Power-on After Power Failure On ASA 5512-X

Mar 3, 2013

how can I enable an automatic power-on after a power failure on an ASA 5512-X?

View 12 Replies View Related

Cisco Firewall :: ASA 5512-X - Automatic Power-on After Power Failure?

Dec 5, 2012

how can I enable an automatic power-on after a power failure on an ASA 5512-X?

View 5 Replies View Related

Cisco Switches :: SF-300-48P Power Failure - Need To Reboot

Apr 4, 2013

We have several  SF-300-48P switches, eveytime there is a power failure the switches need to reboot 2 or 3 times before they are able to route packets again.

View 1 Replies View Related

Cisco Wireless :: 2125 / AP Cannot Join To WLC After Power Failure

Jan 13, 2013

We have cisco wlc 2125 with 13 AP 1131g. All works good. But after power failure one AP can not join to controller, only reset work to recover connection AP to WLC. Additionally, we don't have access to rs-232 port on AP. In this moment on WLC we can see DISCOVERY request from AP and response from WLC to AP, but AP don't send JOIN to controller.

View 2 Replies View Related

Cisco Firewall :: ASA 5505 Power Cycling Failure

Mar 18, 2013

I bougth a used ASA 5505 on ebay which is experiencing this problem [url]... LEVELS or at least the described problem, if i touch the appliance while it is running it will somtimes go to this non working state as well

View 11 Replies View Related

Cisco WAN :: 6509-E Power Supply Failure Sh Log Output

Jan 31, 2012

I have a WS-C6509-E (R7000) and am trying to implement some proactive monitoring for environmental alerts. What is the output from a Power Supply failure for the following “sh log” “sh environment alarm”.

View 1 Replies View Related

Cisco Wireless :: Strange Power Failure With AIR-AP1231G

Mar 25, 2012

I'm having the following issue with a couple of 1231's.
 
Some overall config info first:
 
This is a small office with 2x Catalyst 2950 (24-port, no PoE) switches and 4 AP1231G (autonomous). The APs get PoE from a PWRINJ3 each. The injectors are powered by the AP power supplies. Injectors and power supplies are mounted in the patch closet.
 
The 2 switches are connected together over 4 ports (20-23 on each switch), these ports are set to 1Q Trunk mode.
 
The APs are connected to the switches, 2 to each switch, on port 1-2. These ports again are configured as 1Q Trunk.
 
APs are connected to the switch as follows:
 
   [switch] <- patch cable-> [injector] <- patch cable -> [patch panel] <- static cabling -> [outlet] <- patch cable -> [AP]
 
All this has been working without problems for a number of years.
 
A few weeks back, AP2 did not restart after a power cut (everything else did). All LEDs are off, port on switch has no LEDs lit. I did not get around to investigating this furtehr until last week. I unmounted (failed) AP2, took it to the spot where (working) AP3 hangs, and plugged it to the cable of AP3. AP2 came to life immediately. I unplugged it and plugged AP3 back in, which restarted immediately.
 
So I suspect a power supply issue on AP2. I took the injector and power supply that fed AP2 out of the patch closet. When connecting AP2 directly to the power supply, it came to life immediately. So I figure the injector is defective.
 
On the same day, I notice AP4 is also dead (again all LEDs off, no idea how long, could have been that day or could have been a few days - it has definitely been working after the power cut that appeared to have killed AP2).
 
So I order 2 new PWRINJ3s and for good measure 2 new power supplies. Later that day, I took the injector and power supply that fed AP4 out of the patch closet. When I try this combination (AP4, injector4 and P/S4), and connect it to a different wall outlet (and therefore a different port -16 - on the switch) IT WORKS! Should have triggered questions, but did not immediately.
 
Last Thursday I got the new injectors and power supplies. So I take one of each, hook them upto AP2 at my desk, and AP2 starts up. So I mount new injector2 and new P/S2 in the patch closet, put AP2 back in its place, connect all the cables - NOTHING. AP2 does not start. The "power" LED on the injecvtor lights up green, the "device status" LED remains off. I take AP2, new injector2 and new P/S2 to my desk, hook them upto a wall outlet (connected to switch port 17). AP2 starts immediately.
 
Meanwhile AP3 has (also) stopped working (no LEDs on at all). As far as I can tell, it stopped working after I briefly disconnected (and reconnected) the patch cable between injector3 and the patch panel in the patch closet. The LEDs on switch port 1 are off.
 
I have since tried to power cycle both switches (took power off both, waited a while, poewerd both back on). No change.
 
PS: the APs ran firmware 12.3(8)-JA until recently. AP1, AP3 and AP4 were upgraded to 12.3(8)-JEE after the the power cut that took AP2 out. THis is when I found out AP2 was dead. AP2 was still on 12.3(8)-JA. It was upgraded to 12.3(8)-JEE last week when it was on direct power on my desk.

View 3 Replies View Related

Cisco Firewall :: ASA 5505 Reverts To Old Image After Power Failure

Dec 15, 2012

Firmware asa805-k8 was installed and saved on an ASA5505. Upon power failure the ASA5505 reverts to an older firmware, asa724-k8. 1) Is it normal for ASA5505's to revert to older version upon power failure.  2) ASDM/web browser doesn't work using IE--username and password brings to empty screen. how to revert back to later image.
 
"
# sh ver
Cisco Adaptive Security Appliance Software Version 7.2(4)
Device Manager Version 5.2(4)

[Code]......

View 3 Replies View Related

Cisco Switching/Routing :: 6509 - After Power Failure SSH Does Not Work?

Nov 28, 2012

We had power failure catalyst 6509 and after the device boot up ssh does not work any more  below is error messages
 
line con 0
access-class 90 out
logging synchronous

[Code]....

View 3 Replies View Related

Cisco Switches :: SG 200-08 All LED Lights Flashing Green After Power Failure

May 5, 2012

Thinking back, about a month ago I updated the firmware (I can't check version at the moment). The switch has been working fine since then. Today I needed to move some power cables and the switch lost power. Now ALL of the LED lights are flashing green and I can't access the switch. I've tried setting a static IP on my laptop to 192.168.1.20, mask 255.255.255.0, and accessing the switch on 192.168.1.254, but there's no response. I've tried holding in the reset button for at least 30 seconds while the switch is powered on, AND while powering it on. None of that has worked. Also when I first power it on, the system LED flashes orange very quickly for a second or so, then all of the LEDS start flashing green.

View 5 Replies View Related

Dell :: Dimension E510XP - After Power Failure No Wired Connectivity

Dec 17, 2011

After a recent power outage while my PC was in sleep mode, I don't have wired (Ethernet) connectivity. 

I have new Dimension E510XP Media Center Edition, Version 2002, SP3 ver had an issue with wired connectivity on this PC after coming out of sleep mode.  Of course, the power failure was unusual.

Observations:

- ipconfig /all shows that I have an IP address

- I can ping the DHCP server listed in ipconfig /all and I also can ping google.com.

- I was going to go a restore point set before the power outage.  But, somehow system restore had gotten turned off.    Oh, well.  I did go ahead and turn system restore back on.

Things I've already tried that did not solve the issue:

- Reboot

- Uninstall/reinstall the network adapter driver.  Device Manager says the network adapter card is working properly.

- Looked for an updated network adapter driver on Dell's website.  Turns out that I have the latest driver already.

- Followed many of the steps from Microsoft at [URL]

- Checked McAfee Security Center firewall permissions list to see if something got changed.  Everything looked okay.  Also disabled the firewall just to be sure,

- Disabled SafeEyes internet filter.

- Reset the router.  Also swapped router ports with a known good PC.  The known good PC still had connectivity, the affected PC (the E510) did not.

View 6 Replies View Related

Can't Connect To Internet - Get The Message Catastrophic Failure 0x8000ffff?

Dec 21, 2011

I am running 32 bit windows 7 on my mac with boot camp. Normally, all is fine, but for some reason I can't connect to the internet on windows 7, but I can on my Mac OS on the same computer. I ran troubleshoot, but it says it can't find any problems. I was connecting to my home network yesterday, but I couldn't get on the internet, however now I'm just stuck connecting to "Identifying...". I installed a game yesterday, and I'm thinking that could be the problem, but I can't uninstall it because I can't connect to Steam. I tried system restore, but I get the error message 0x80070001, and if i choose to press run system restore anyway, I get the message "Catastrophic failure 0x8000ffff". Everything is plugged in.

View 3 Replies View Related

Missing Local Area Connection Icon In Network After Power Failure?

Sep 29, 2011

Missing local area connection icon in network connection after power failure?

View 1 Replies View Related

Linksys Wireless Router :: WRT54G2V1 Failure - Power Led's Emitting light very Weak

Nov 20, 2012

1、the router power led's  emitting light very weak ,

2、client pc cannot get ip from connected router

these error perhaps happened after a plug power jack action. Dc-dc chip is ME5513,the voltage on its pin4 is about 11.94V,and the voltage on following electrolytic  capacitor is 3.3V,its seem normal.

View 1 Replies View Related

Linksys Wireless Router :: E1000 - Hardware Failure / Power Light On Continuously

Aug 7, 2011

I have a ~3 month old e1000 v2. In the last 24 hours it appears to have died, all 4 ethernet lights plus the power light and the one to it's left are on continuously. Before I dispose of it, does anyone know if this really is a hardware fail or is there some way to recover it? I've tried a few resets, power cycles and leaving it off for a few hours in the hopes that would bring it back to life but to no avail.

View 5 Replies View Related

Cisco Switching/Routing :: 3560v2 / Ws-c3560v2-48ps-s (inline Power Failure)

Jul 22, 2012

I have a switch 3560v2 with an IOS 12.2(50) SE1.All the lights ON and console error message below:POST: inline power post failed for port 0 up to port 15.Then, the system hanged and all lights (indicator) ON.

View 5 Replies View Related

TP-Link 150Mbps Wireless :: TL-WR740N Failure To Connect To Internet / Server

Apr 24, 2013

Region : Argentina
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP :
Region : UnitedKingdom
Model : TL-WR740N
Hardware Version :
Firmware Version :
ISP :

I've configured the router using the Easy Setup Assistant CD provided and have a wifi connection between the router provided however when using network diagnostics, while the wifi connection is fine, I am getting "failed to connect to Internet" and "failed to connect to server" messages. I have tried adjusting settings manually but without any progress.

View 8 Replies View Related

Cannot Connect To Internet After Power Outage

Apr 4, 2012

I'm running Windows Vista desktop on a wireless network. It's been working fine for months. Just lost power for a minute today and ever since I can't connect to the internet, only locally. My desktop can't even identify the network. My laptop (I'm using it to send this message) is also wirelessly connected and works fine, as do other wifi enabled devices in the house. I've done the power off and on for the modem and the router but it's made no difference. I've rebooted the desktop system too. I've run the ipconfig /all and am concerned I have no Default Gateway listed.

View 6 Replies View Related

Computer Won't Connect To Internet Via TP Link Power Line

Feb 1, 2013

I have got a TP link wireless router connected by TP link power line ethernet adapters connected to my sky box, one to Samsung Smart TV, which both work fine the third I have connected to my computer. This shows up as as a local area connection but with no internet access. I have similar problems to other people with internet access dropping out after installing Windows * and had hoped an ethernet connection would be more stable. Any thoughts on why I can't connect to the internet via my powerline adapter.

View 5 Replies View Related

D-Link DIR-615 :: Cannot Connect To Internet / Orange Power Light

Mar 11, 2012

I reseted my router because I couldn't go in the login so now eveything is green except the earth looking thing next.the power it is orange Cause I really need my internet

View 1 Replies View Related

Linksys Wireless Router :: WRT400n Cannot Connect To Internet After Power Outage

Mar 14, 2012

We had a power outage the other day, and now the wireless router cannot connect to the internet. Network Magic shows there is no connection from the device to the internet. I tried repairing it through Network Magic but it wasn't able to fix it.
 
My PC is directly connected to the wireless device by LAN cable. If I connect the PC directly to my DSL router I can connect to the internet, but not if I connect to the wireless router and from there to my DSL router. I tried resetting the wireless router to factory defaults and then going to [URL] and resetting up the router security settings. But Network Magic still shows the bad internet connection.
 
I then tried resetting the router to factory defaults again and installing it from scratch using the setup CD but that failed as well. I'm not at home right now so can't remember exactly at which point it was but I think it was either when the setup wizard tried to detect the device or install the device.This is the second time I've had to reset up my router due to power outage. Last time I was able to get it working by doing the first steps above.

View 2 Replies View Related

Aquos TV Failure To Connect

Feb 15, 2012

having the same problem with my Aquos TV. We have a 2wire router, that is directly connected to a home computer. all other computers are connected via wireless with no problems. I have followed the manual instructions, the TV finds the router with enough bars, input the wep key, but it fails to connect. [code]

View 4 Replies View Related

LAN Connection Failure But Connect To Wireless?

Mar 22, 2011

it an hp notebook PC with an intel processor and 3GB of RAM

View 1 Replies View Related

Servers :: Cannot Connect To PVP - Connection Failure

Sep 28, 2012

I can't connect too any game servers.This is the error i get when i try to log into any acount on League of Legends:Connection Failure: Unable to connect to the PVP.net server.Information regarding what may have caused this error can be found here.Service availability can be viewed on the League of Legends Server Status web page.

View 5 Replies View Related

Cisco Switches :: SG200-50 Could Not Connect After UPS Failure

Jan 9, 2013

I have an issue with the Cisco SG200-50p and almost all of the POE ports on the switch.
 
We had an issue with the UPS in the server rack yesterday where the UPS failed and turned off all power to the equipment in the rack. It is possible that something was blown in the UPS itself. I was able to reroute power to all devices but the only one that seems to have an issue is the SG200-50p switch. After the power was restored the unit refuses to acknowledge all the IP phones plugged into the POE ports. Running a copper test via the web interface on the majority of the POE ports are listed as Operational Status: Down.
 
I have tested the affected ports with Laptops, other switches, and simple loop test to verify that the port operational status after a coper test goes back to 'Up' when any of these devices are connected to the those ports. However it fails to recognize when one of the IP phones are connected at all. There are not even any lights on the device for those ports and the status is listed as 'Down' when I plug in any of the IP phones. The IP phone is a Linksys IP Phone SPA922. I know the phones are good because when I connect them through another POE switch they come on and function properly.

View 4 Replies View Related

Internet Wired Connection Failure?

Apr 3, 2013

i have a Echolife HG520c. internet through wireless is working fine but the internet through cable is not. this seems unusual FYI: i have checked the connections and all are fine, i have restarted my system and also the Echolife HG520c and it still has the same problem

View 1 Replies View Related

Can Use Internet - Get General Failure When Ping

Aug 11, 2011

I can access the internet just fine, but when I try to connect using a VPN It times out.When I ping the desktop in question, I get a timeout, and when I ping anything from the desktop I get "general failure".I've tried allowing echo responses through the firewall, and disabling the firewall, to no avail.

View 6 Replies View Related

Cisco Wireless :: Cannot Connect To Wlc4402 Via Console - Hardware Failure?

Jun 21, 2007

I made a lot of tests during some days with a wlc4402 and everything was ok.
 
One day when I tried to reset the system I had a lot of errors (see attach) and could not go on. After changing the image the following output appeared: "RAM Disk Image Integrity Check Failed (Bad Magic Number) Hanging". Now I have no response from the controller.

View 4 Replies View Related

Cisco Routers :: Total Failure To Get SR520-ADSL-K9 To Connect To ISP

Dec 15, 2011

We've (an independent school) just bought an SR520 with a view to replacing one of our Draytek 2820s. We need to set up some site-to-site VPN with NAT and the Drayteks won't do it.
 
I've been trying to configure the SR520 in just the most basic fashion using CCA (3.1) and the CLI but with no success. I can't get a PPP connection with our ISP.
 
I've tried following the instructions in the software config pdf and also tried replicating the various 'running configs' reported in other posts in this forum to allow connection to a UK ISP, with no success. I don't know how many times I've reset the poor thing to factory defaults.
 
I have to say that I'm dismayed at how flaky the CCA appears to be. Many of the things I've tried with it simply don't work and often end up in it hanging. Close to useless in my view.
 
So instead I've tried to use the CLI which seems a lot more solid but is somewhat impenetrable and there's precious little by way of supporting explanation.

View 12 Replies View Related

Broadband :: Failure Of Internet Explorer Browser?

Nov 3, 2011

i am not able to use the internet explorer browser to connect to the internet it may be connected to my installing of the adobe flash player that a site said that i needed .

View 1 Replies View Related

Connected To Internet But Getting General Failure When Pinging

May 1, 2012

I am have 3 machines int he house connected to the internet but one does not have internet access. It shows connected to the wireless network and from the command prompt there is an ip assigned to the laptop. But i cannot ping the gateway or any ip I get General Failure.

View 1 Replies View Related

Internet Access Stopped - Other PC's On LAN Working OK / General Failure

Aug 19, 2012

I have a new Alienware X51 running Win 7. It's connected to a home LAN, both wired and wirelessly. For the prior two days internet connectivity has been fine. Today, the PC will not connect to the internet. The Network and Sharing center in control panel shows that the PC is connected to both the wireless network and the wired network, but with no internet connectivity. All other computers and devices in the house are able to connect to the internet. Tried restarts, virus scans, router power off/on, ipconfig /release and renew, all with no luck. When I try and ping other computers in the LAN or the router I get a "General Failure" message.

View 8 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved