I can't connect too any game servers.This is the error i get when i try to log into any acount on League of Legends:Connection Failure: Unable to connect to the PVP.net server.Information regarding what may have caused this error can be found here.Service availability can be viewed on the League of Legends Server Status web page.
View 5 Repliesit an hp notebook PC with an intel processor and 3GB of RAM
View 1 Replies View Relatedi have two servers that is Primary domain Controller and File Server. When i remove the client computer from the domain and try to rejoin the domain again it refuses, when i ping it replies. i can not assess files in the file server It prompt"Logon Failure: the target account name is incorrect" Suprisingly When i logon in other clients its OK. but some clients give ths said error though the communication with the server is fine
View 1 Replies View Relatedi'm trying to connect 5 servers together to create a private network.Each server has a network of it's own and i'm trying to make all 5 servers communicate with each other to share and search data simultaneously..
View 16 Replies View Relatedi have a Echolife HG520c. internet through wireless is working fine but the internet through cable is not. this seems unusual FYI: i have checked the connections and all are fine, i have restarted my system and also the Echolife HG520c and it still has the same problem
View 1 Replies View Relatedtrying to connect studio 540 desktop by wireless connection with homeowners airport extreme. windows cant find connection. sure had wireless card installed at purchase. what adapter do i need? wireless card? what are options for wireless network connection for this desktop
View 1 Replies View RelatedI have recently purchased a Wireless-N repeater which is now up and running and connects with both Ipad, iPhone and other laptops with ease. The problem is that I can't connect using my own PC. I'm using Windows Vista and the connection to the repeater seems fine, it just can't connect to the Internet. Every time I try and open a web page I receive the following message.Error 105 (net:ERR_NAME_NOT_RESOLVED) Unable to resolve the servers DNS address.
View 7 Replies View RelatedI have a Cisco 819 WAN Router (C819 Secure M2M GW (non-US) 3.7G HSPA+ R7 w/SMS/GPS).Software: Cisco IOS Software, C800 Software (C800-UNIVERSALK9-M), Version 15.2(2)T, RELEASE SOFTWARE (fc1)
For dialing in at my Provider (T-mobile Germany), I use the following chat-script:
chat-script gsm "" ATZ "" AT+CGDCONT=1 "OK" "AT!SCACT=1,1" TIMEOUT 60 "OK" "ATD*99#" "CONNECT"
Dial-In is successful after Reboot.Now, i want to simulate a conenction fault, e.g. termination by mobile provider.So I used the command "clear int cellular 0".After that, The router can't dial in again.
Debug shows:
Dec 7 11:04:03: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to down
Dec 7 11:04:14: CHAT3: Attempting async line dialer script
Dec 7 11:04:14: CHAT3: Dialing using Modem script: gsm & System script: none
Dec 7 11:04:14: CHAT3: process started
Dec 7 11:04:14: CHAT3: Asserting DTR
[code]...
Is the "clear interface cellular 0" the wrong way to test this, or why can't the Router reconnect?The only solution is a reboot, but that is not the best option. The router should automatically redial.
I will just explain my setup:
I have a ADSL Huwavi modem by my ISP installed at my place.. Now the wireless from that device is very bad.. So I purchased WAG120N to setup a daisy-chain kind of setup in my other bedroom. I also put another D-link DIR-600 in between to give a connection to the first floor (via Ethernet cable).
So my huwavi is the ISP device, then a LAN from it goes to the dlink internet (WAN) port. then one cable from the d-link LAN port to the LAN1 of WAG120N and another upstairs.
Now all of this was working perfectly.. I put same SSIDs and Pwds on both ISP router and WAG120N and i was getting seamless net..
Now yesterday we removed the ISP modem to do some shifting.. Upon reconnecting, the ISP modem, Dlink work as before, but the WAG120N refuses to connect to the net.. it shows DSL down and doesn't access the www.
What I felt is that since i changed LAN ports on my ISP device and dlink, the static IP settings on the WAG120N should be changed.. i modified it, set to to point to the dlink for internet and huwavie for DHCP.. yet nothings happening..
I even connected the WAG120N directly to the Huwavie, yet it fails to connect to the net..
having the same problem with my Aquos TV. We have a 2wire router, that is directly connected to a home computer. all other computers are connected via wireless with no problems. I have followed the manual instructions, the TV finds the router with enough bars, input the wep key, but it fails to connect. [code]
View 4 Replies View RelatedI can't connect my DirecTV DVR to my WRT54GS router. I am using a new cat6 ethernet cable to the router.
View 5 Replies View RelatedIve got a virtualised firewall running 3 security contexts in routed mode. What am experiencing is that i cannot connect to an OUTSIDE host through the security contexts. From the firewall itself i cannot ping the directly attached host on the OUTSIDE interface but i can ping the directly attached host on the INSIDE interface. When i reload the firewall box, the first ping to the OUTSIDE host would be successful but subsequent pings fail and thus total connectivity is lost.
I even tried upgrading to ASA version 8.4(1) but still the same.
I have a ACE4710 setup to load balance a couple of web servers. The real servers all show as inservice as do the propbes and serverfarms/virtual servers. If I ping the Virtuual server ip address I get a reply but it I try to access VIP via telnet or web browser. I get a connection could not be open error on the client.The question is how do i determine where the error is comming from so far I can not tell if the client is getting through the acl or not.I have used the trouble shooting guide and nothing has worked to determine the cause so far. show service-policy int479 detail does not show an increase in the hit count when I try to connect.show stats conn does not show an increase in failed or timed out connections when i try to connect. [code]
View 3 Replies View RelatedI've got the power cut while PC was running (w7). After rebooting I'm not able to connect to the internet anymore.
In Device Manager, under Network Adapters there is a "Realtek PCIe GBE..." device properly installed. But under Other Devices there are now more entries with exclamation mark:
- Network controller
- Multimedia controller
- PCI Communication controller
etc
I tried updating the drivers, then deleting and reinstalling but no success so far. Still can't connect to the internet. The browser can see the router, at 192.168.1.1 I don't know where the problem is.
Missing local area connection icon in network connection after power failure?
View 1 Replies View RelatedI just purchased 2 AE3000 adapters to update my wireless network and cannot get either of them to connect to my wireless network through either of two computers I tried. It hangs for a while looking for address and then I get the 'limited or no connection' note. But yet when I plug in my old AE1000 adapter into either computer I get connected right away. I've looked under the device manager and it shows up there, the LED lights come on and I see my wireless network show up on available networks. I am using the windows wireless manager in lieu of the Linksys one and as such I don't think any specific drivers are being used. I bought two updated adapters to start with is to keep current and NOT have problems.
XP Pro SP3
WRT350N Router
I have an issue with the Cisco SG200-50p and almost all of the POE ports on the switch.
We had an issue with the UPS in the server rack yesterday where the UPS failed and turned off all power to the equipment in the rack. It is possible that something was blown in the UPS itself. I was able to reroute power to all devices but the only one that seems to have an issue is the SG200-50p switch. After the power was restored the unit refuses to acknowledge all the IP phones plugged into the POE ports. Running a copper test via the web interface on the majority of the POE ports are listed as Operational Status: Down.
I have tested the affected ports with Laptops, other switches, and simple loop test to verify that the port operational status after a coper test goes back to 'Up' when any of these devices are connected to the those ports. However it fails to recognize when one of the IP phones are connected at all. There are not even any lights on the device for those ports and the status is listed as 'Down' when I plug in any of the IP phones. The IP phone is a Linksys IP Phone SPA922. I know the phones are good because when I connect them through another POE switch they come on and function properly.
I recently updated my WRT54G V3 to frimware 4.21.5 and now get regular wireless connection issues. The wired connection never has any problem (can connect to the router and the internet), but none of the wireless devices can see either.
The problem happens every couple of days, and cycling the power seems to be the only fix. When the problem does occur, the wireless devices don't even see the broadcasted SSID. But cycling the WRT54G's power fixes that.
I've gotten a few suggestions to do a "30-30-30" reset, but can't find exactly what that entails.
Connection denied due to NAT reverse path failure
View 2 Replies View RelatedI am running 32 bit windows 7 on my mac with boot camp. Normally, all is fine, but for some reason I can't connect to the internet on windows 7, but I can on my Mac OS on the same computer. I ran troubleshoot, but it says it can't find any problems. I was connecting to my home network yesterday, but I couldn't get on the internet, however now I'm just stuck connecting to "Identifying...". I installed a game yesterday, and I'm thinking that could be the problem, but I can't uninstall it because I can't connect to Steam. I tried system restore, but I get the error message 0x80070001, and if i choose to press run system restore anyway, I get the message "Catastrophic failure 0x8000ffff". Everything is plugged in.
View 3 Replies View RelatedI made a lot of tests during some days with a wlc4402 and everything was ok.
One day when I tried to reset the system I had a lot of errors (see attach) and could not go on. After changing the image the following output appeared: "RAM Disk Image Integrity Check Failed (Bad Magic Number) Hanging". Now I have no response from the controller.
We've (an independent school) just bought an SR520 with a view to replacing one of our Draytek 2820s. We need to set up some site-to-site VPN with NAT and the Drayteks won't do it.
I've been trying to configure the SR520 in just the most basic fashion using CCA (3.1) and the CLI but with no success. I can't get a PPP connection with our ISP.
I've tried following the instructions in the software config pdf and also tried replicating the various 'running configs' reported in other posts in this forum to allow connection to a UK ISP, with no success. I don't know how many times I've reset the poor thing to factory defaults.
I have to say that I'm dismayed at how flaky the CCA appears to be. Many of the things I've tried with it simply don't work and often end up in it hanging. Close to useless in my view.
So instead I've tried to use the CLI which seems a lot more solid but is somewhat impenetrable and there's precious little by way of supporting explanation.
I am in the process of opening an internet cafe. I dont know exactly what a pc server does on the network... or do I really need one? Is the switch/hub sufficent to connect all pcs to the moderm to connect to the internet?
View 1 Replies View RelatedRegion : Argentina
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP :
Region : UnitedKingdom
Model : TL-WR740N
Hardware Version :
Firmware Version :
ISP :
I've configured the router using the Easy Setup Assistant CD provided and have a wifi connection between the router provided however when using network diagnostics, while the wifi connection is fine, I am getting "failed to connect to Internet" and "failed to connect to server" messages. I have tried adjusting settings manually but without any progress.
I currently have one home WWW server running on port 80 which is obviously the HTTP port. If I wanted to run another web server on the same connection, how would I do this? Is it possible? Obviously, I can't port forward the same port for more than one IP.
View 3 Replies View RelatedI have a server running win2000 server managing a network of 30 computers, it als a proxy server where all pc connecting to for internet access. The server is connected to Wimax through a router. Lately i have a vpn for PDA's through GSM lines where am supposed to connected a Modem (part of VPN)to this server so that PDA' s and modem can be on the vpn.The problem is that when I connected the GSM Modem the internet connection through router get disconnected. How do I connect the modem on the server without disconnecting the wimax internet connection
View 3 Replies View RelatedMy issue is that for as long as I can remember I lose connection temporarily while playing computer games online. It has plagued me through location changes, ISP changes, router changes, and modem changes. What seems to happen is the internet losing connection for a second, causing my computer to reconnect to the server, which takes a few more seconds. This happens at random, and at least twice every fourty-five minutes or so. It happens regardless of the game I'm playing (though I've only tried to recreate it with LoL and Dota 2). For those gamers out there, you can understand how frustrating this could be.I have tried both wired and wireless connection. I am running Windows 7 Studio XPS 435T/9000, and have recently replaced the graphics card
View 4 Replies View RelatedThe Lg840g is a tracfone with wifi capability. I get strong wifi signal and connection at home, but receive failure to connect to requested host message when I open the browser. This phone works at wayport wifi, so I assume it's a compatibility problem with the router. Is there a fix? (Router works great with our Acer and Kindle tablets though.)
View 1 Replies View RelatedI am connected but always have the red cross up in the connection tray
View 1 Replies View Related"Remote Desktop Disconnected - The remote connection has timed out. Please try connecting to the remote computer again."I am not behind any network, firewall, outer...I tried to turn off firewall and antivirus programs to see if they are blocking it. It didn't work. All I could find from Microsoft support site refer to the server side configuration. But I know problem isn't with server, because I am able to connect from another PC (notebook running windows 7 with wireless connection). It is working straightforward with default settings.
View 1 Replies View Relatedcannot share internet connection in windows 7?
View 1 Replies View Relatedhow to uninstal remote desktop connection, computers are networked
View 1 Replies View RelatedI'm having an issue with my work computer where it can connect to all of the servers in the company accross the country EXCEPT the servers located in New Jersey. I am running Windows XP SP3. I am able to ping the servers and get a response back, but my network drives are disconnected and I cannot open them. I have tried completely uninstalling the driver for my network adapter and reinstalling it with no affect. Mine is the only computer having this problem and I have uninstalled all software that was installed within the past month to be sure. It is ALL of the servers in New Jersey so I know it's a problem with my computer and not the serers. I had a similar issue a while ago where I could ping Google, but could not get to the website, and that ended up being the ZoneAlarm firewall that I had. That was fixed by uninstalling ZoneAlarm and doing an ipconfig /release & /renew. I re-registered some dlls but that didnt work either.
View 1 Replies View Related