Cisco Switching/Routing :: 7204 VXR Newly Installed Router Got Reloaded
May 5, 2012
One of my newly installed router got reloaded ,showing me below error . The same IOS im using in another router and it works fine without any issue ,but this newly installed router gave me this problem. [code]
cisco 7204VXR (NPE-G1) processor (revision B) with 983040K/65536K bytes of memory.
View 5 Replies
ADVERTISEMENT
Apr 20, 2012
I am trying to configure a newly installed HWIC-4ESW on a 2811 router to bridge to the FE 0/0 interface. Currently, I have a cheap switch connected to FE 0/0 which in turn connects to all the phones, however now I just want to connect all the phones to the HWIC and have it internally bridge to FE0/0 for the connectivity to CME, etc.
View 5 Replies
View Related
Apr 28, 2013
install Bluetooth for my newly installed Win8.I tried all the posted links for Bluetooth.I have Win8 on Dell Inspiron 5010, so which one will be suitable for it?
View 7 Replies
View Related
Dec 13, 2011
We have cisco 4506 and this got reloaded automatically and showing reload in show version output but no one made switch reload.
CORE-SW-2 uptime is 8 minutes
System returned to ROM by reload
System restarted at 12:37:58 IST Wed Dec 14 2011
View 8 Replies
View Related
Nov 7, 2011
I have a 3845 router which got reloaded immediately and need to know the reason for the reload .Router have created crash info detail .
View 3 Replies
View Related
Nov 28, 2007
I can't seem to find out what this means. Every 6 months or so, my 7204 locks up. I can't even get to it via the console port and I must reboot to access it. I noticed this alarm in my logs.( ASSERT CRITICAL PO1/0 Threshold Cross Alarm - B3) I've looked on-line but can't pinpoint it's meaning. Looks like a flapping interface but might be something else.
View 6 Replies
View Related
Oct 20, 2012
It has been work for a year without problem. We didn't do any change. Recently, we have to reboot thist router to make it work. After the rebooting, the router will work for a while. It could work from few days to a week, and tt stops working again.
View 7 Replies
View Related
May 1, 2012
I just upgrade a license on a cat 4510. The license installed but the EULA was not accepted and it will not upgrade to the new feature set.
View 1 Replies
View Related
Oct 26, 2011
We have Cisco 4507-R installed at customer site which got hang twice and became normal after getting booted.I have analyzed show tech-support for this switch after reboting but not found relevant logs for hang issue,
View 7 Replies
View Related
Jun 29, 2012
I have cat4500 with subject module. There is strange behaviour over module installed in 3rd slot only, some ports are connected, UP & working fine. But If I am connecting new ports over same module, are not coming UP.Duplex/speed settings already checked & are fine. If i connect same machine to any other module, it perfectly comes up & operation is fine.
View 3 Replies
View Related
Aug 4, 2011
Our router reloaded yesterday with a Software forced crash . I ant to identify the reason for the crash and also the fix for this problem . Attached is the crash info output .
[Code] ......
View 3 Replies
View Related
Nov 8, 2011
I need to route a subnet from a 7204 to 2 different gateway's which are not Cisco based. I cannot use HSRP, GLBP or VRRP as the other 2 gateways don't support theses protocols. Yet they do support OSPF, RIP, and BGP.... Take note that this setup is in a ISP scenario. How can I acheive gateway redundancy?
View 4 Replies
View Related
Nov 16, 2012
I bought a newly refurbished netegear wireless router from amazon and it came with no information and/or passwords,eetc. I connected the yellow wire like the old one was but no password to get me through the security entry for connecting to SSID for lapto
View 2 Replies
View Related
Mar 2, 2013
So anyone can use this channels without any restrictions and without register this AP.So how can i use this channels on my newely purchased EA3500? from drop down menus only low range is available.ive tried 2 different FW from linksys site (Cisco FW and Smart WiFi FW) in both i cant use this frequences .Also for this router no alternate FW available because inside Marvell chipsets (im not understood correctly why, but i suppose all about "closed FW").Also ive tried to change timezones (in hope that this range is magically appear), but magic not happened. So i have question: why i cant use this 5gHz range when its legal in my country?May be Linksys support watch on this problem and release new firmware for Russia with support of this channels?Also i knew that E3200 have this range enabled on default FW, but not on EA3500.
View 9 Replies
View Related
May 8, 2011
One of our Routers 7204 rebooted unexpectedly. I try to access Output interpreter but is not working. The output from our router is the following:
WAN-ROUTER#sh version
Cisco IOS Software, 7200 Software (C7200-ADVIPSERVICESK9-M), Version 12.4(15)T2, RELEASE SOFTWARE (fc7)
[Code].....
View 7 Replies
View Related
Jan 18, 2012
I need to configure BGP on our 7204 and 2811 router. The 7204 is our main router and currently running EIGRP internally. Our remote locations just moved to an MPLS connectivity and they have a 2811 router. I will need to configure BGP for the routing protocol. I have the AS number and the remote AS number. Attached is the the current configuration of the two routers.
View 4 Replies
View Related
Dec 22, 2011
We are replacing a DS3 Internet connection with a 100 Mbps fastE connection from a Tier 1 Provider. I currently have a Cisco 7204VXR with 512 Mb DRAM and 128 Mb of Flash and two 10/100 ports that is connected to the DS3. I also have a 3845 with 1 Gb of DRAM and 256 Mb of Flash with two 10/100/1000 ports available.
We are currently running BGP, below is the summary
BGP table version is 88880414, main routing table version 88880414
379041 network entries using 44347797 bytes of memory
379043 path entries using 19710236 bytes of memory(code)
View 4 Replies
View Related
Jan 9, 2011
I was attempting to setup our 7204 Cisco router to use RADIUS for authentication via the AAA commands. I must have messed up when configuring it as it comes up via TELNET asking for a username and password but doesn't take my AD credentials. How might I login to this router to fix the config? Do I need to do a password recover process?
One note, I didn't save the running-config to startup-config, so if I restart the router will it load the startup-config, thus overwriting the running-config that wasn't working?
View 2 Replies
View Related
Jul 11, 2011
We had some issue with Datacentre ACE modules. Both primary and DR ACE modules got restarted in 16 hours difference. Unfortunately Syslog was not configured on the ACE and local logging got cleared after restart. The current IOS version is A2(3.2). The modules uptime was around 300 Days. Here is the log from 6509 switch during the restart. [code]
View 7 Replies
View Related
Jan 23, 2011
reloaded xp. dont seem to have internet drivers. down loaded new drivers and seem to do no good. still unable to connect to internet.
View 1 Replies
View Related
Jun 29, 2011
I had a malware attack and decided to reload my XP Media Edition on my Dell XPS 400 series. After the disc reformat and reload of XP from the operating system CD, and then loading the drivers CD, I cannot connect to the internet. The plug for the ethernet cable is red/yellow on two different jacks in the house. The modem is supplied by ATT U-verse. The TCP/IP is connected at 400 Mb/s but showing "0" data transfer in or out. The internet connection was working before the XP reload. I did not backup an "image" and so I may have lost my registries? Is there a way to "turn on" the ethernet port?
View 5 Replies
View Related
May 12, 2011
We have purchased a 2901 router with permenant licenses for ipbase, security and uc. The router came shipped with c2900-universalk9-mz.SPA.150-1.M3.bin but there are newer releases available. I understand that our licenses will cover us to upgrade to the latest version, c2900-universalk9-mz.SPA.151-4.M.bin, but when I attempt to download I am denied.
How do I go about downloading and upgrading?
View 3 Replies
View Related
Mar 13, 2012
RARP (Reverse Address Resolution Protocol) is a protocol by which a physical machine in a local area network can request to learn its IP address from a gateway server's Address Resolution Protocol (ARP) table or cache. A network administrator creates a table in a local area network's gateway router that maps the physical machine (or Media Access Control - MAC address) addresses to corresponding Internet Protocol addresses.When a new machine is set up, its RARP client program requests from the RARP server on the router to be sent its IP address. Assuming that an entry has been set up in the router table, the RARP server will return the IP address to the machine which can store it for future use.Among the passage of words i read, there was this sentence i were not sure, "A network administrator creates a table in a local area network's gateway router that maps the physical machine (or Media Access Control - MAC address) addresses to corresponding Internet Protocol addresses." Does it means each time a host computer joins in the ethernet LAN, the network administrator would manually add in it's MAC address in the router table, so it would allow the newly joined computer to request IP address from it's MAC address?
View 1 Replies
View Related
Oct 24, 2011
Im unable to access my newly configured 1841 via SSH or via CCP from the WAN side.
Is there anything I can do from the LAN side in CCP that will assure that this router is able to be managed from the WAN?
View 10 Replies
View Related
Aug 4, 2012
I'm setting up Blast! Comcast/Xfinity internet (50mb/s) using an SB6120 modem and a linksys E3000 router. I haven't done anything yet, as i haven't received the modem in the mail yet, but i want to be prepared and knowledgeable when it all arrives. Here are my questions I've heard that running this router/modem setup on the N band at 5Ghz provides the best signal strength. How do i configure this? The main goal is to take advantage of as much of the 50mb/s as i can (i know this number is not practical due to overhead estimations etc).My newly built desktop has one free PCI-E slot (the other is occupied by my EVGA GTX 670) and 1 or 2 PCI slots. What's the best option to give my desktop wifi capabilities (pci card or usb adapter) in order to maximize signal strength? I'm about 10 feet away from the router, a door separates the computer from the router.
View 8 Replies
View Related
Nov 26, 2012
I've just finished building a new desktop and the problem is that it cannot connect to the internet. I've got a ethernet cable connected from the modem to the desktop. I know the modem is working properly since my laptop and itouch can connect to the internet wireless. The desktop can recognize the modem and it says it's connected to the modem but it says the modem isn't connected to the internet. I dunno what to do I've got the LAN drive installed all the neccesary requirements for the desktop but it just won't connect
View 2 Replies
View Related
Jul 31, 2012
I just built a new computer that will not connect to the internet, but only while using my wall port, and only this new computer, and only while connected through the router. Totally bizarre, right?I just built a new computer with a fresh install of Windows 7. I set it up directly connected to the router, where I applied all windows updates. I then moved it to where my old computer is, which uses a wall port to connect to the router in another room, where this new computer then fails to connect to the internet or to the router's setup. The new computer's Ethernet LEDs will light up, and the computer will automatically obtain an IP address, but will not connect to the internet or even the router setup.
View 2 Replies
View Related
Apr 4, 2011
I have a WMP54GS Installed in a SONY VAIO with a Pentium 4 2.6 ghz processor, 2 gb of DDR Ram, and Just over 60 GB of Hard Drive space. I've run this setup for over two years at this point, all on an XP operating System, from sp1 all the way up to sp3 with no issues. A week ago I ended up with a trojan on my system, and had to do a full recovery. This time I used an XP Pro copy that came with sp2. Not the same copy of XP that had been running previously. Needless to say when I had the OS finally installed and running, it didn't recognise my wireless adapter. I figured I needed to run through the same process as I had when I first purchased the adapter, and took the card out, ran the intsallation disc, followed the intructions, powered off, and reinserted the card. When I booted back up, there was simply a gray box in the lower left showing "disabled". I clicked on it, and it showed that there were no networks in range, when there should have been several. The only tab on the screen that I was able to click was "exit". I wasn't able to perform manual setup, and when I clicked the "xp setup" option, nothing happened. I was unable to find the device in the device manager (though it may be in the "other devices" list with a question mark, but I can't tell. Would it be something like "network controller" or "ethernet device"?) It doesn't appear in my network connections either. The LED on the card itself is dormant. Nothing happening. I figured at this point that it must not be fastened adequatly to the PCI slot. So I opened the case, took the card out, and fastened it back in nice in tight. No more give, and in the same slot it had always been in when operating properly. Still the same issue. I've done this a couple more times now, and with the same results. I just don't get it. I've followed the intrsuctions to the letter, and no results. Do I perhaps need to skip the cd and try to install the latest drivers for the card instead? Will that allow my PC to recognise it? I have another machine in my home, and can download a driver and transfer it by disc or flash drive to the other machine if need be.
View 1 Replies
View Related
May 23, 2011
I have a cisco 7204 vxr that terminates a 300 meg ethernet circuit asn well as an mpls DS-3. CPU increases along with utilization of the ethernet circuit. When the utilization gets to around 150 Mbps on the receive, the cpu is maxed out at 100%. I am wondering if the router can support the amount of traffic coming through it. The majority of the traffic is voip using g729 codec, so packet size is small. We are no where close to peak utilization and cpu is at 39%. Here is what I see currently:
#sh verCisco IOS Software, 7200 Software (C7200-ADVIPSERVICESK9-M), Version 12.4(15)T4, RELEASE SOFTWARE (fc2)Technical Support: [URL] 1986-2008 by Cisco Systems, Inc.Compiled Thu 13-Mar-08 10:40 by prod_rel_team
ROM: System Bootstrap, Version 12.3(4r)T3, RELEASE SOFTWARE (fc1)BOOTLDR: 7200 Software (C7200-KBOOT-M), Version 12.3(15), RELEASE SOFTWARE (fc3)
uptime is 3 years, 1 week, 3 days, 6 hours, 40 minutesSystem returned to ROM by Reload CommandSystem restarted at 08:26:49 UTC Wed May 14 2008System image file is "disk2:c7200-advipservicesk9-mz.124-15.T4.bin"
This product contains cryptographic features and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not implythird-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible forcompliance with U.S. and local country laws. By using this product youagree to comply with applicable laws and regulations. If you are unableto comply with U.S. and local laws, return this product immediately.
[code].....
View 5 Replies
View Related
Dec 19, 2011
We have a cisco 7204 VXR and would like to know the module which has two fastethernet port. We tried a PA-2FEISL-TX but it did not work.
View 1 Replies
View Related
Mar 6, 2012
Today we got a new cisco 7204 with NPE-G2 , so we wanna to configure to root for the internet so here is my scenerio
1- Public Ip address =155.155.155.20
2 Private Ip Address =192.168.2.0 /24
3- Gateway = 155.155.155.1
4-DNS Server = 194.155.12.133
Interfaces:
1- Gigabite 0/1 - We put this for Public ip address
2- Gigabite 0/2 - and this for Private Ip address
how to route this for the internet . after routed we want our client computers to get internet from Gigabite 0/2 Interface
View 8 Replies
View Related
May 20, 2012
is 633+ seconds (approximately 10 minutes) load time normal for a Cisco 7204 router? I find that it takes forever for the router to do :Self decompressing the image". I tried the latest IOS and tried different bootloaders but it doesnt seem improve it?
View 2 Replies
View Related
Feb 28, 2010
We have point to point metro ether net link terminating on 7204VXR router.On this point to point link we are configuring GRE over ip sec. Problem is when the traffic exceeding 8mbps we started getting packet drops. from the Cisco documentation it seems the tunnel bandwidth is by default 8mbps and there is parameter like Inherit/receive but those actually not change the tunnel interface bandwidth.If we just give tunnel bandwidth with bandwidth mentioned it allows me to give option of 100mbps but again the tunnel interface bandwidth remains 8mbpos only and probably that 100mbps is useful only for routing decisions.
i am using advance security 12.4.15T12 image. Whether this is a limitation or any other way to go beyond 8mbps for the tunnel interface (7204VXR-NPEG1 processor)
View 18 Replies
View Related