We have purchased a 2901 router with permenant licenses for ipbase, security and uc. The router came shipped with c2900-universalk9-mz.SPA.150-1.M3.bin but there are newer releases available. I understand that our licenses will cover us to upgrade to the latest version, c2900-universalk9-mz.SPA.151-4.M.bin, but when I attempt to download I am denied.
How do I go about downloading and upgrading?
So anyone can use this channels without any restrictions and without register this AP.So how can i use this channels on my newely purchased EA3500? from drop down menus only low range is available.ive tried 2 different FW from linksys site (Cisco FW and Smart WiFi FW) in both i cant use this frequences .Also for this router no alternate FW available because inside Marvell chipsets (im not understood correctly why, but i suppose all about "closed FW").Also ive tried to change timezones (in hope that this range is magically appear), but magic not happened. So i have question: why i cant use this 5gHz range when its legal in my country?May be Linksys support watch on this problem and release new firmware for Russia with support of this channels?Also i knew that E3200 have this range enabled on default FW, but not on EA3500.
View 9 Replies View RelatedRARP (Reverse Address Resolution Protocol) is a protocol by which a physical machine in a local area network can request to learn its IP address from a gateway server's Address Resolution Protocol (ARP) table or cache. A network administrator creates a table in a local area network's gateway router that maps the physical machine (or Media Access Control - MAC address) addresses to corresponding Internet Protocol addresses.When a new machine is set up, its RARP client program requests from the RARP server on the router to be sent its IP address. Assuming that an entry has been set up in the router table, the RARP server will return the IP address to the machine which can store it for future use.Among the passage of words i read, there was this sentence i were not sure, "A network administrator creates a table in a local area network's gateway router that maps the physical machine (or Media Access Control - MAC address) addresses to corresponding Internet Protocol addresses." Does it means each time a host computer joins in the ethernet LAN, the network administrator would manually add in it's MAC address in the router table, so it would allow the newly joined computer to request IP address from it's MAC address?
View 1 Replies View RelatedIm unable to access my newly configured 1841 via SSH or via CCP from the WAN side.
Is there anything I can do from the LAN side in CCP that will assure that this router is able to be managed from the WAN?
I'm setting up Blast! Comcast/Xfinity internet (50mb/s) using an SB6120 modem and a linksys E3000 router. I haven't done anything yet, as i haven't received the modem in the mail yet, but i want to be prepared and knowledgeable when it all arrives. Here are my questions I've heard that running this router/modem setup on the N band at 5Ghz provides the best signal strength. How do i configure this? The main goal is to take advantage of as much of the 50mb/s as i can (i know this number is not practical due to overhead estimations etc).My newly built desktop has one free PCI-E slot (the other is occupied by my EVGA GTX 670) and 1 or 2 PCI slots. What's the best option to give my desktop wifi capabilities (pci card or usb adapter) in order to maximize signal strength? I'm about 10 feet away from the router, a door separates the computer from the router.
View 8 Replies View RelatedI bought a newly refurbished netegear wireless router from amazon and it came with no information and/or passwords,eetc. I connected the yellow wire like the old one was but no password to get me through the security entry for connecting to SSID for lapto
View 2 Replies View RelatedI've just finished building a new desktop and the problem is that it cannot connect to the internet. I've got a ethernet cable connected from the modem to the desktop. I know the modem is working properly since my laptop and itouch can connect to the internet wireless. The desktop can recognize the modem and it says it's connected to the modem but it says the modem isn't connected to the internet. I dunno what to do I've got the LAN drive installed all the neccesary requirements for the desktop but it just won't connect
View 2 Replies View RelatedI just built a new computer that will not connect to the internet, but only while using my wall port, and only this new computer, and only while connected through the router. Totally bizarre, right?I just built a new computer with a fresh install of Windows 7. I set it up directly connected to the router, where I applied all windows updates. I then moved it to where my old computer is, which uses a wall port to connect to the router in another room, where this new computer then fails to connect to the internet or to the router's setup. The new computer's Ethernet LEDs will light up, and the computer will automatically obtain an IP address, but will not connect to the internet or even the router setup.
View 2 Replies View RelatedI have a WMP54GS Installed in a SONY VAIO with a Pentium 4 2.6 ghz processor, 2 gb of DDR Ram, and Just over 60 GB of Hard Drive space. I've run this setup for over two years at this point, all on an XP operating System, from sp1 all the way up to sp3 with no issues. A week ago I ended up with a trojan on my system, and had to do a full recovery. This time I used an XP Pro copy that came with sp2. Not the same copy of XP that had been running previously. Needless to say when I had the OS finally installed and running, it didn't recognise my wireless adapter. I figured I needed to run through the same process as I had when I first purchased the adapter, and took the card out, ran the intsallation disc, followed the intructions, powered off, and reinserted the card. When I booted back up, there was simply a gray box in the lower left showing "disabled". I clicked on it, and it showed that there were no networks in range, when there should have been several. The only tab on the screen that I was able to click was "exit". I wasn't able to perform manual setup, and when I clicked the "xp setup" option, nothing happened. I was unable to find the device in the device manager (though it may be in the "other devices" list with a question mark, but I can't tell. Would it be something like "network controller" or "ethernet device"?) It doesn't appear in my network connections either. The LED on the card itself is dormant. Nothing happening. I figured at this point that it must not be fastened adequatly to the PCI slot. So I opened the case, took the card out, and fastened it back in nice in tight. No more give, and in the same slot it had always been in when operating properly. Still the same issue. I've done this a couple more times now, and with the same results. I just don't get it. I've followed the intrsuctions to the letter, and no results. Do I perhaps need to skip the cd and try to install the latest drivers for the card instead? Will that allow my PC to recognise it? I have another machine in my home, and can download a driver and transfer it by disc or flash drive to the other machine if need be.
View 1 Replies View RelatedOne of my newly installed router got reloaded ,showing me below error . The same IOS im using in another router and it works fine without any issue ,but this newly installed router gave me this problem. [code]
cisco 7204VXR (NPE-G1) processor (revision B) with 983040K/65536K bytes of memory.
install Bluetooth for my newly installed Win8.I tried all the posted links for Bluetooth.I have Win8 on Dell Inspiron 5010, so which one will be suitable for it?
View 7 Replies View RelatedI am trying to configure a newly installed HWIC-4ESW on a 2811 router to bridge to the FE 0/0 interface. Currently, I have a cheap switch connected to FE 0/0 which in turn connects to all the phones, however now I just want to connect all the phones to the HWIC and have it internally bridge to FE0/0 for the connectivity to CME, etc.
View 5 Replies View RelatedI get on-line, and the internet all-of-a sudden starts to show that I've downloaded my limit of 250MB. Now, I am on Hughesnet for internet service, can not get on DSL, wont happen already asked. Now, I am running a router, only way my wife and son can access the internet. They have laptops windows 7 and build-in Wireless Cards. I have a desktop windows 7. My updates are scheduled in the morning hours about 5AM so their is no reason for the computer to update. Same goes for my wife and son, their are set for early morning hours as well. I get an error message as soon as I click on my webpage that I want to browse, Internet Can Not Display The Webpage or something to that effect.
View 8 Replies View RelatedWhat ISO do I need to purchase to get Cisco IOS Firewall on a Cisco 2901 - is it just IP Base or do I need one of the Security IOSs?
View 1 Replies View RelatedI have a 1-Port 3rd Gen Multiflex Trunk Voice/WAN Int. Card - T1/E1 in a 2901 that I want to configure for data only (T1 connection to the Internet)I don't see any options in the IOS for using this thing as a serial interface (data), only options for configuring PRI/ISDN.
View 5 Replies View RelatedThe license has been installed onto the router. Here is the relevant out from the show license all:
License Store: Primary License StorageStoreIndex: 0 Feature: ipbasek9 Version: 1.0 License Type: Permanent License State: Active, In Use License Count: Non-Counted License Priority: MediumStoreIndex: 1 Feature: WAAS_Express Version: 1.0 License Type: Permanent License State: Active, Not in Use License Count: Non-Counted License Priority: Medium
WAAS license as it says that this is not in use, WAAS under the interface is not possible.
I am trying to come up with a config for implementing QoS over a 512 kbps WAN link that will traverse voice and data traffic for now. I am using a Cisco 2901 router with 15.1(3)T IOS on it. my config is below
class-map match-any DATA-PRIORITY match protocol citrix match protocol sshclass-map match-any VOICE-CONTROL match protocol skinny match protocol mgcp match protocol h323class-map match-any VOICE match protocol rtp audio class-map match-any ANY match any [ code]...
THE ISSUE IS : when i add in the service-policy output WAN- QOS- POLICY command , i get the error " insufficient bandwidth 256kbps for bandwidth guarantee (180)". if i take out the " bandwidth 512 " command out then i get no issues adding the above command on interface g0/1
I have a Cisco ASA and a 2901 Cisco Router connected via site-to-site VPN. The ASA can ping over the VPN to computers behind the router, but the router can not always ping to computers in the ASA network. When i ping from a computer in the IOS router's 10.100.36.0 network the requests times out most the time; although every few minutes, i will get about 10 pings back, then stops working again.
I uploaded their two configurations.
The ASAs public IP is 20.20.20.5 and local (inside) network of 10.101.36.0/24
The IOS routers public IP is 20.20.20.10
There are many internal networks, but 10.100.36.0/24 is the one with issues.
I try to make a gre tunnel with 2 cisco routers 2901, ping responds between tunnel ip's ends, but I don't have pings from the pc's inside the networks. [code]
View 7 Replies View RelatedHow do I disable fragmentation on a 2901 router? I want it to simply drop packets oversized packets.In my lab, I am trying to test various MTU issues. I'm trying to use a 2901 router to simulate the WAN equipment that my WAN provider would deploy in production. In production i'm expecting the WAN to only support an MTU of 1320 with no fragmentation at all.
View 2 Replies View RelatedPhysical devices are a Cisco 2901 (CISCO2901/K9) with GE0/0 configured as 192.168.1.1
Connected through a D-Link DGS-1210-24 configured as 192.168.1.202
Running on a domain with an HP domain server as 192.168.1.2
The 2901 was an EHWIC (VA-DSL-A oPoTS) on EHWIC 0/0/0
GE 0/0 on the 2901 is physically connected to the DGS-1210 which is physically connected to the server.
VDSL 0/0/0 is physically connected to the DSL jack.
So far the configuration reports all is connected, and I can ping the gateway of our ISP (using CLI or Cisco CP); however the server reports no internet connection and no workstations can access the 'net.
Once connected; I'd also like to allow ports through for use on the network (25, 80, 110, 443, 987, 1723) - but not sure on how to do that just yet!
Our IP is 202.27.19x.19x
Our Gateway is 202.27.217.5
[Code] ......
I have recently bought cisco 2901 in order to replace it with our 1811W that we have at the moment.When I try to set a failover / backup with rtr; it seems like the function is not valid.Once I select rtr and set the object #, the reachability command is not available.Does that mean this function is not a part from the license package I have?
View 6 Replies View RelatedI have inherited a setup for a custom application and would like to know if this is the only way this could be set up. How would you do it?The application uses dedicated T1 links to our vendors. There is a Cisco 2901 router in the middle providing the connections. Traffic to specific vendor's IP's are routed to their prospective connections. I have attached a network diagram and a config for the 2901. The way my predecessor(s) set this up, each different vendor uses a different private IP address for the internal links. This seems odd to me. Shouldn't there be a way to have only one subnet on the inside and have the links NAT depending on which route it takes? The servers have persistent routes built in them to send vendor traffic to the associated IP on the router. E.g., traffic to Vendor 1 is routed to 192.168.50.1, the 2901's IP address for the Vendor 1 network. That traffic is then NAT'd to an IP address associated with Vendor 1's link and the 2901 then routes the traffic to the Vendor's end of the link.
I would think that I should be able to revamp this so that internally we're only using one subnet and the traffic could NAT at the link associated with the Vendor. I recently had to add the 3rd vendor connection, and wound up having to duplicate what was done for the other two in order to get it working quickly. I didn't have the time to wrap my head around the best way to revamp the whole thing.
I recently obtained a 2901 router running 15.2(2)T to replace my old 877 which was running 15.1(4)M1. The 2901 is humming along quite nicely but I have had difficulty configuring one feature which was working fine on the 877. The router needs to be a PPTP client to a hosted VPN service. On the 877, I had it configured like this: [code] I then had a dialer interface to actually set up the connection, and some PBR to control what went over the VPN. All well and good, and it worked fine. But on the 2901, when I try to configure the same thing, there is no such command as "protocol pptp" -- the only option is protocol l2tp.Was PPTP support deprecated somwhere between 15.1 and 15.2, or does the 2901 itself not support it for some reason? Obviously I understand that l2tp is superior to pptp, but at the moment this is my only option.
View 2 Replies View RelatedI have one router 1841 in which i configured PBR for internet traffic from LAN. I hv two ISPs few server are configured for ISP1 and few for ISP2.I planned to shift my existing setup at 2901 G2 router. when I am configuring the same config on this router so traffic is passing through only from one ISP not from other, if I troubleshoot so I see that the interface which is connected with ISP2 is not getting any input/output packet.
Config is here:
==========
interface FastEthernet0/0
description ****** ISP2 ******
ip address 203.xx.xx.110 255.255.255.248
[Code].......
I try to make a gre tunnel with 2 cisco routers 2901, ping responds between tunnel ip's ends, but I don't have pings from the pc's inside the networks.
[code]....
Why I cant correctly use ip sla command. I only have on my 2901 such commands: ip sla ?
key-chain Use MD5 Authentication for IP SLAs Control Messages
responder Enable IP SLAs Responder
server IPPM server configuration
There is my "sh ver"
ROM: System Bootstrap, Version 15.0(1r)M15, RELEASE SOFTWARE (fc1)
And...What should i do. if i want to create a failover with to WANs
Where's the ideal place to put the KS? My current setup is 1 KS, 19 GM. The KS sits BEHIND a GM, so all other GMs have to come through one GM to get to KS.Now, I have purchased two dedicated KS routers. I configured one today, and placed it right on my WAN. My WAN is a L2 Ethernet domain, so i just provisioned a switch port in the WAN vlan, and away we go. I copied RSA keys over from the current KS, configured redundancy and the two hooked up, saw each other and it seems to be good to go. For the ACL, I put in an exclustion for my two KS to talk to each other:
deny ip host 192.168.250.40 host 192.168.250.41 (Old IP, New IP)
deny ip host 192.168.250.41 host 192.168.250.40.
I used a test router and pointed it to the new KS, it registered without a hitch... HOWEVER about two hours later (my 7200 second timeout) I lost ALL my branches. My 18 other GM were still pointed to the OLD IP only, they didnt have the second IP configured yet. In a hurry, I quickly disabled the redundancy configuration on the old KS and had to go to each GM and do a 'clear crypto gdoi' on each one to get them to re-register. There were no log messages about not being able to rekey, no log messages about dropped peerings, nothing. Once I did that, everything returned to normal.
The Question I have...
Would having configured the redundant KS caused this problem? Would having one KS behind a GM and the other Coop KS in the WAN make a difference?
Relevant config from existing KS, 2801:
crypto gdoi group GETVPN_GROUP
identity number 1234
server local
rekey retransmit 60 number 2
rekey authentication mypubkey rsa GETVPN_KEYS
[Code]...
I have a 2901 ISR G2 router, with IOS 15.0.1M3 , this router is not working with static NATing, I have tried to configure this router with one internet link and make few static translations with it. But this configuration is perfectly working with 1841 ISR router.
View 2 Replies View RelatedWe've have a client who had a ordered 2 units of 2901 router to have site to site connectivity. User has bought a leased line of 256kbps from service provider in between two sites, but the issue is the service provider has layed a rj11 cable and there is no rj11 interface on 2901 router it only has two rj45.
View 5 Replies View RelatedNeed to know if I have 2 type of license on my 2901 router: ipbase and uc, will the 2 type of fuctions of this license work at the same time. Another words will i have route and nat functions work with voip having to type of license on my 2901?
View 3 Replies View RelatedI been working with PPTP server on cisco IOS since a log time ago. Up to release 15.0 seems is just stopped working. I mean external users can log in the pptp but after logged in there no traffic flow. A simple downgrade to 12.4 solves the problem.
But now i have all my infrastructure with ISR2 2901 and all IOS are 15.
I'm trying to run the ISM-VPN-29 in a 2901 router. Cisco says that the SECK9 and HSECK9 licenses are needed to operate this ISM. However, they also say that the HSECK9 license is not available on the 2901. I'm running the SECK9 license but it's still not working.
This link, table 5 states that the HSECK9 feature license is for 2921 and 2951 only:[URL]This link states that it is a requirement to run the card, and also that the card works on the 2901:[URL]
I am running 15.3(1)T IOS.