Cisco AAA/Identity/Nac :: C220 ISE On UCS Platform With UC
Mar 7, 2013
We are looking to deploy ISE supporting 5000 devices and would like to use the Cisco UCS platform to host this. Looking at the spec required a C22 M3 would be sufficient; however we would also like to host some UC applications on the same server if resources allow.
Therefore we would like to deploy ISE on a C220 M3 server and connect the associated NIC to a DMZ. We would then like to deploy UC applications such as CUCM and CUPS on the same UCS server with a NIC attached to the internal network.
Also while the UC application would require a UC Foundation License (R-VMW-UC-FND5-K9) whould this also meet the requirements for ISE?
View 1 Replies
ADVERTISEMENT
Mar 21, 2011
Any relevant doc for ACS4.2 on 1113 platform to be integrated with Unix Directory service having LDAP10.2.0.0 version from Oracle or guidance available.
View 1 Replies
View Related
Jan 12, 2013
I cannot integrate Virtual MSE 7.3.101 with my Prime Infrastructure 1.2 After I setup MSE via its wizard, I make a change on WCS username and password. When I try to integrate MSE with Prime Infrastructure, Prime notify me about the mismatch username/password.
Both systems are fresh install on my UCS C220 M3.
View 4 Replies
View Related
May 26, 2011
I am doing a school research project in which I am setting up an OC-192 ring for a company (contract work through AT&T). I have chosen to use the Cisco ONS 15454 SONET MSPP as my platform. The company currently has locations in Chicago and Philadelphia and connects them through an OC-12C ATM connection and they are looking to add 2 gigabit ethernet connections.My question is what cards and parts will I need for the Cisco ONS 15454 SONET MSPP, and how much will everything cost? I have been searching the internet for components and prices and I have found it extremely difficult to find any information.
View 2 Replies
View Related
Oct 17, 2012
I currently have a 50Mbps Internet Connection provided by an ethernet handoff for hosting some webservers. We are looking at adding an additional 10Mbps Internetn connection and route BGP between the two. For the 50Mbps connection, i'm using a Cisco 2951 router. I also have another 2951 router to terminate the 10Mbps connection. Does these router have enough horsepower to fully route BGP?
View 1 Replies
View Related
Jun 13, 2007
Is there any way to auto migrate my 3030 VPN configuration to an ASA platform?
View 3 Replies
View Related
Nov 27, 2011
I want to select catalyst 3560G for my network. But IOS SLB need to be implemented in my network. I only know catalyst 6500 series can support this feature and i am not sure whether 3560G can support this feature. what platform and IOS version i need to implement IOS SLB?
View 1 Replies
View Related
Mar 22, 2011
A make one BOM and i just ask my self can we order on the one platform ( for example 5510-SEC-BUN-K9 ) SSL Essentials license ( this license is on the platform by default we buy 250 users ) and i need 50 Users license from them to be Premium.
Can i buy those two license on the same platform and is this will work ?
View 3 Replies
View Related
Jan 3, 2012
During WAN troubleshooting, I did a "clear interface ser0/0/0" on a branch router. It has two WAN links. I lost ssh/telnet connectivity but both WAN links were still replying to pings. We did a manual power off of the router to regain connectivity.Is there a known issue with this command on this IOS version? We're using Cisco 2911 platform with IOS 15.1-1.T2 version.
View 1 Replies
View Related
Apr 23, 2012
I am currently working on our Cisco voice platform at work.
Our Cisco firewall engineer has left and I have been given the task of looking after the firewalls as our Chief Exec seems to think that Cisco Voice is similar to Cisco ASA firewalls,
Are there any books/videos out that you can recommend to learn the about firewalls quickly.
View 1 Replies
View Related
Apr 24, 2013
I am trying to bridge the traffic(including different vlan traffic) from rtrA to rtrB using "bridge-group" functionality.I achived the same using a 7200 using the below configuration. [code] When I tried the same using 7600 router ping failed between rtrA and rtrB. Then from the documents it seems "bridge irb" is not supported in 7600.Is there any other way we can achieve the same fuctionality ( eg: using switchport also fine) ?
View 3 Replies
View Related
Feb 22, 2011
I've been experiencing a problem with my existing 3845's that may mean I may have to upgrade to a newer faster platform.Currently I have ISP links to 2 providers and run BGP. Each ISP link plugs into a separate 3845 NM-1GE fiber port. Both links are 100Mb ethernet handoff. There is an average of 50 - 60Mbps traversing each link during peak times. I am experiencing a large number of Input errors on both ISP links almost all of the errors are ignored. I opened a TAC case and I'm told that the 3845 can not handle this much traffic along with an ACL on the ISP interface and BGP. TAC engineer tells me that the RX ring of the interface is being overrun and tuning buffers will not make any difference. CPU util never goes above 25%.
View 1 Replies
View Related
Aug 15, 2011
What is the minimum platform that supports GETVPN over DMVPN?
I have been looking around cisco website but couldn't find a document with the supported platforms.
We have branch offices with Cisco 861 routers and i would like to know if we could use GETVPN with these routers.
View 1 Replies
View Related
Oct 30, 2011
I'm going to replace a Cat6513 with a Nexus 7018. In my Cat6513, there are object tracking config as follows:
ip sla monitor 1
type echo protocol ipIcmpEcho 112.78.254.249
timeout 3000
frequency 6
ip sla monitor schedule 1 life forever start-time now
ip route 172.17.7.0 255.255.255.0 165.202.51.46 name VPN-1 track 123
Is there similar feature in Nexus platform? Because from Nx-OS command ref, I only found:
ip route ip-prefix/mask {[interface] next-hop} [preference] [tag id]
Seems can't associate a track object to a static route in Nx-OS?
View 4 Replies
View Related
Jan 29, 2013
You all know the senario; A managed device, let's say a c2801 router is being replaced with newer platform, let's say a c3900e series router. Might aswell be a C2960 being replace by a c3750x
I the goodolddays, with LMS3.2.1, you would get the "conflicting device" notice that the SNMP OID has changed on this managed device. you then need to press update and the device would then be managed once more.
How is tyhis done in LMS 4.2.2 ?
I seem to see more and more device in one of my installation, that DCR sees teh new OID and updates, but Inventory fails ... I get more of this, and the error is just; Internalt error in the job-browser .
I see Device Center info is wrong, but DCR info is right ..
What to do, and how do LMS handle this ? Can I get notice around when a device has been changed ?
View 5 Replies
View Related
Nov 15, 2012
Does the 4500E platform (sup7E) support the extension VLAN over MAN connections? In wich technology?
View 1 Replies
View Related
Mar 6, 2013
Does the Cisco vWLC support the cisco AIR-AP1231G-A-K9 platform?
View 4 Replies
View Related
Dec 22, 2011
I´m looking for an IOS on a 7609 SUP720/MSF3 that supports the NAT-PT feature (IPv4 to IPv6 translation). I searched on the Cisco Feature Navigator but the tool didn´t show up any IOS for the 760x platforms. I only got the feature "NAT-PT: Support for Overload (PAT)" with IOS 15.xS train.
View 2 Replies
View Related
Feb 5, 2013
We have the following design in mind
3750 Stack (Voice gateway for phones configured on the 3750 and has a VPC nexus)
+ +
+ +
+ +
(Nexus5596) ++++++++++ (Nexus5596) (Gateway for all other vlan like PC / servers / etc)
+ +
+ +
+ +
3750x access layer (VPC to Nexus)
[CODE].....
View 1 Replies
View Related
Nov 22, 2011
Setting up Netflow from the 7010 platform to Solarwinds?I implemented the following code on both of my cores (VPC/HSRP Redundant Linked Pair) but had the following issues:
1. One of the cores I could see was sending Netflow records every few seconds whereas the other was not doing anything
2. Solarwinds was not seeing any of those records coming in and was showing last update from both devices as "Never"
Note that I have netflow already working as my Riverbed (fairly intelligently) already updates Netflow.Also i was all set to debug this myself but there doesn't seem to be debugging for Netflow that I can see?!?
View 0 Replies
View Related
Mar 22, 2012
I want change my old router to new one. I have problem with runing SERVICES READY PLATFORM WIZARD.
View 1 Replies
View Related
Aug 2, 2011
Our company has recently upgraded our firewall from a Borderware Steelgate v7.1 platform to a Cisco ASA 5520 platform. Needless to say the interface on the Cisco platform is much more complex and I don't have much experience working with firewalls. Our other IT guy is out of town and this is the first time I have worked on this setup.
I need to create the following access rule
I need to open port 4**0 to be allowed through the firewall from external ip address 10.XXX.XX.XXX only. Then forward port 4**0 to 10.XX.XX.XX port 80 tcp
View 9 Replies
View Related
Aug 24, 2012
A customer wants to upgrade an IOS Base (cat4500-ipbasek9-mz.122-25.SG4.bin) of a WS-C4507R Cisco, for a IOS that have a enterprices functionalities.We install an IOS cat4500e-entservicesk9-mz.122-53.SG5.bin, but we had the following results:
config-register = 0x2102
Autobooting specified file using Variable BOOT .....
Current BOOT file is --- bootflash: cat4500e-entservicesk9-mz.122-53.SG5.bin
[Code].....
View 1 Replies
View Related
Sep 11, 2011
Any equivalent show command to get the "FIB TCAM Usage" on An ASR 1006 ?the "show platform hardware capacity forwarding" does not work on ASR1006 Example on 6500: Router# show platform hardware capacity forwarding.
View 1 Replies
View Related
Mar 26, 2012
I have 2 C2811 ISRs runnning c2800nm-advsecurityk9-mz.124-15.T17.bin and having on board: 1 Virtual Private Network (VPN) Module.is it possible to enable IPSec stateful failover (or switchover, SSO) between these boxes? I get different infos from Cisco sources. url...All commands were accepted, but failover doesn't seem to be statefull (I loose connection for few seconds and VPNs are reestabilishing)
View 5 Replies
View Related
Mar 6, 2013
When we originally deployed our Cisco Prime NCS and MSE Virtual Appliances, the VMsphere server they were on was not able to assign us the level of resources we requested. We installed the MSE as "LOW" system due to the memory and CPU requirements. It has a 2000 CAS element limit. At the time we were licensed for 1000, so no huge problem.
Now, we purchased a Cisco UCS C240 server to run our Prime NCS and MSE on, which gives us our own environment where we have plenty of resources. I also bought 6000 CAS element licensing.
The catch is, how can I either do a fresh install, using the same UID, on our new UCS server, so that our licensing is still valid when we move the box, or, is it possible to do some sort of platform reinstall or upgrade after moving our original MSE VM guest over to the UCS server? Sadly, I can't even utilize the additional 1000 CAS element licensing at this time because it won't allow me to add the 6000 license and use only 2000, on the LOW appliance. So I've got to get these VM guests moved, but maintain any UID's so that the licensing still works.
Is it possible to disconnect the licensing we have, from the UID, and move it to a different UID?
View 6 Replies
View Related
Nov 13, 2011
How the police flow command ( see below) works only in the 6500's platform? Can it apply in 3745 router?
View 2 Replies
View Related
Feb 13, 2013
I want to know what the default behavior about the command 'mls qos trust dscp' under router platform interface. the router is ASR1000 series.we don't need to put above command line to trust dscp in case of router? otherwise, we have to add it as welll as like switch platform.
View 4 Replies
View Related
Apr 10, 2012
Any info regarding the number of MAC Entries of Catalyst 3560X/3750X Platform? I can find that number in 3560, 3750 ds but not in 3560x ds.
View 2 Replies
View Related
Mar 25, 2012
I found this "VWIC2-2MFT-G703 1841 - 3845 tied to platform slot density" from Cisco web site, does it mean if Cisco 1841 have two wic slots I can put two VWIC2-2MFT-G703 in this chassis.
Reference link [URL].
View 1 Replies
View Related
Jan 4, 2012
Is it possible to view extensive information about switch supervisor on WS-C4506 platform? I could use show module or show inventory, but this only displays the module name. For example how to view the amount of SRAM the SUP has? Or any other similar more detailed information?
View 7 Replies
View Related
May 6, 2012
I got the error in object when I try to add a new HSRP group in new vlan.All the HSRP group has the same HSRP group the 2.another way to provide clients's default gateway redundancy for each Vlan intead to use the HSRP?
View 4 Replies
View Related
Mar 27, 2013
I am having problems with IGMP and QoS on CAT6500 platform with SUP720 engine.The problem is, it seems that all IGMP packets are getting marked with DSCP 48 when sent out of the switch regardless of any input service policy. I found several articles saying that PFC QoS does not apply to IGMP packets. However in IOS 15 that should be possible, but I didn't get it to work there either. [code]
View 0 Replies
View Related
